Search Documents

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and, liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise eight be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and. removing the disintegrated clay particles from wells after the perforated pipes have been inserted. Mechanical methods for removing mud sheaths are quite satisfactory, but prompted by tie request of certain operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions.

Jan 1, 1934

By John E. Pahlman

An increasing number of gold and silver mining operations are employing cyanide solutions to effectively dissolve silver and gold from finely disseminated ores. Many of these operations use small, packaged processing systems like the State of Maine filter system, which employs zinc precipitation of gold and silver. Solution-clarifying filters in these systems become blinded with calcium carbonate (CaC03) scale and require frequent (every 2 to 10 days) dismantling of the filter units for acid cleaning, This is a hazardous operation as it is not compatible with the alkaline cyanide leach solutions and may result in the evolution of toxic hydrogen cyanide (HCN) gas during cleaning and during any accidental acid spill. The Bureau of Nines has investigated an alternative, nonacidic method of cleaning blinded State of Maine filters that employs ethylene- diamine-tetraacetic-acid (EDTA) type chelating agents to dissolve the scale. In situ cleaning of a 150-st/d State of Maine filters with EDTA- type chelating agents was successfully demonstrated. Greater than 90 pct of the CaC03 scale was removed in about 10 min with circulation of 31 L of 2.5-pct-EDTA solution through the filter unit. The EDTA cleaning method not only eliminates the cyanide hazard in filter cleaning but is advantageous from the standpoint of operating costs and productivity.

Jan 1, 1986

By B. E. Davis

Over 80 pct of domestic phosphate rock, which is the starting material for phosphorus-containing fertilizers, comes from central Florida deposits. As K-her grade deposits are depleted, lower grade phosphate ores containing 'Mg0 in the form of dolomite are encountered. Treating high MgO ores with present beneficiation technology will not yield a concentrate meeting specifications for acidulation. The Bureau of Mines conducted research on three high-MgO phosphate samples from south Florida. The sales contained, in percent, 5.4 to 10.2 P205, 1.9 to 7.6 MgO, and 35.3 to 60.1 acid insolubles. A technique of sizing, grinding, desliming, scrubbing, and redesliming was used to produce a feed suitable for continuous flotation studies, A conventional fatty acid-fuel oil rougher flotation followed by two to three cleaner stages resulted in concentrates containing, in percent, 30.7 to 31.3 P205, 0.6 to 1.3 MgO, and 2.5 to 4.8 acid insolubles. The P205 recovery from the flotation feed ranged from 55.1 to 89.7 pct.

Jan 1, 1984

By Lawrence G. Houk

Lithium is the lightest of all metals, but as it deteriorates rapidly in air it has no structural applications. Alloys of lithium that will float upon water can be made with other light metals, but these ultralight alloys are not useful in aircraft production or elsewhere at present. Alone or alloyed with alkaline earth meals, lithium acts as reining agent on molten metals, and as a minor constituent with other metals it imparts characteristic properties to the allay. Lithium compounds have somewhat wider application in commerce than either the metal or the alloys. They are used in the glass, ceramic, chemical, and air-conditioning industries and less extensively in the optical, pharmaceutical, electrical, and textile industries. The United States is the leading producer anti consumer of lithium ores and compounds and apparently has the largest known ore reserves. The value of lithium ores and primary chemical byproducts produced is relatively small, yet the lithium chemical industry yields products worth hundreds of thousands of dollars each year, owing partly to the high degree of purity demanded by the trade for most finished products and to the low combining weight of lithium. Fortunately, the low-grade ores can now be concentrated economically, and this fact, together with our extensive reserves, assures adequate supplies to meet any reasonable increase in demand. Lithium is listed as essential by both the American and British war agencies, and its military importance may be greatly enhanced.

Jan 1, 1942

By M. F. Chambers

The U.S. Bureau of Mines conducted experiments on electrowinning of neodymium metal by using a molten-metal cathode at 650° C and an electrolyte of 50 mol pct NdCl3 (neodymium chloride) and 50 mol pct KCI (potassium chloride). The molten-metal cathodes were alloys of magnesium and zinc or magnesium and cadmium. Current efficiencies were 90 pct with a Mg-Zn cathode and 80 pct with a Mg-Cd cathode; The Mg-Cd cathode was easily separated from the electrolyte. In contrast, the Mg-Zn cathode tended to mix with the electrolyte, making separation difficult. The cathode metals were separated from the neodymium by distillation at 1,100° C under a vacuum of 10-3 torr. Neodymium metal of 99.9+ purity was recovered from the Mg-Cd alloy cathode after 30 min distillation time. The neodymium recovered from the Mg-Zn system contained almost 2 pct Zn after vacuum distillation. Continuous operation using the Mg-Cd alloy cathode was demonstrated.

Jan 1, 2010

By P. C. Good

The Bureau of Mines conducted a laboratory investigation of a sinter-leach method to recover aluminum and fluorine from waste carbon potlining residues from secondary cryolite recovery operations in aluminum reduction plants. After removal of carbon by burning, the residue was sintered at 900° to 1,100° C with silica and N2CO3, then crushed and leached with dilute NaOH solution, dilute Na2C03 solution, water, or water containing residual Na2O which remained in the sinter after reaction and decomposition of Na2CO3. Over 90 percent of the contained aluminum and up to 87 percent of the contained fluorine were extracted from this waste product in the form of a mixed alkaline solution. Treatment of the alkaline solution with CO2 yielded a white precipitate containing 89 percent of the original aluminum and 61 percent of the original fluorine as a mixture of synthetic cryolite and alumina, together with a variable excess of soda.

Jan 1, 1969

By George S. Rice, C. W. Owings

"Brattice cloth is an important material in coal-mine ventilation practically all coal mines use some brattice cloth, gassy mines a large amount. It is employed in three ways:Crosscut brattices.Curtains in haulageways.Line brattices in gassy mines.In each case brattice cloth is used to deflect part or all of a split of the mine ventilating current into or toward the face of a working place. As a general rule, its use in a particular location is temporary.A crosscut brattice should be employed only until a permanent stopping has been erected. Such a brattice is subject to little wear when in actual service, the chief damage occurring when it is taken down and put up again.When used for curtains on haulageways or haulage crosscuts to deflect the air current up into rooms or headings, the wear on brattice cloth is considerable, as mine cars, machines, and personnel constantly pass under the curtains which last only a few days or a few weeks in an active part of the mine. For such purposes tightly woven smooth cloth is desirable, so that it will not be easily torn. Curtains should not be used back from the working places, as they sometimes are, to deflect the main. split, as the leakage of air is too great. Doors should be used in such places."

May 1, 1928

By William W. Adams

Not since complete records of accidents first became available has the safety record of the quarrying and related industries of the United States been as favorable as it was in 1940. The combined accident-frequency rate was lower and therefore better than in any year since 1916, the first year for which complete and comparable figures are available. Although operating companies began to furnish accident reports to the Bureau of Mines in 1911, the reports for that year and the next few years were obviously incomplete as to number of accidents reported, especially slight injuries involving only 1 or 2 days of disability of the injured employees. By 1916 the reports from operating companies appeared to be reliable as to completeness of coverage of slight injuries. Although the number of men employed in 1940 was by no means a record, it represented a gain over each of the 2 preceding years. Likewise, the number of man-hours worked during 1940 was larger than in 1938 and 1939.

Jan 1, 1942

By Louis A. Panek

The practice of roof bolting or rock bolting to stabilize rock surrounding underground excavations has increased tremendously within a few years. This widespread application has led to many questions concerning the mechanics of bolting and has pointed up the need for a quantitative method of designing bolting systems. To answer these questions a research program was initiated to determine the principles of roof bolting. The first problem chosen for investigation was the use of bolts to reinforce bedded roof, since the great majority of bolts are used under these conditions. The attack employed is a combination of theoretical and experimental stress analysis. Centrifugal testing of models was chosen as the experimental method because it is particularly suited to the study of stratified roof. This report describes the models, the experimental method, and the model-prototype relations. By using dimensional analysis, a general expression for a roof-bolting design formula in terms of the structural variables has been obtained. Certain model-prototype similarity requirements have been relaxed, thereby minimizing the number of variables to be studied and extending the applicability of quantitative test data to a large class of full size structures.

Jan 1, 1956

By W. N. Cathey

Many materials including carbides, silicides, phosphides, borides, nitrides, oxides, and metals were studied by the Bureau of Mines as potential fuel cell catalysts for electroreduction of oxygen in a 1[N]H2S04 electrolyte. The objective of this study was to assess the potential of abundant, low-cost materials as substitutes for platinum or to increase the catalytic efficiency of platinum. Several compounds were rejected because of their reaction in the corrosive environment of the oxygen electrode. However, some of the remaining were the most active catalysts. Activity of carbides such as tungsten carbide could be improved by doping with platinum-group metals, by varying stoichiometry, or by sputtering on a layer of platinum. While no catalysts were found with activity as high as platinum, some compounds were shown to be deserving of further investigation.

Jan 1, 1979

By D. A. Wilson

Several promising systems for selectively oxidizing the iron in an iron-tin alloy commonly called "hardhead" were investigated in a research project conducted to devise a method for recovering tin from this troublesome alloy. A satisfactory oxidation method was developed and tested successfully on melts of 2,000 grams. Molten hardhead (near 1,080° C.) was blown with air to oxidize iron and leave tin in the reduced state. Recovery of available tin was 96 to 98 percent. Tin products contained 2 to 0.1 percent iron which was reduced to 0.06 percent by filtration at 250° C. Iron oxide formed during oxidation was absorbed by a fluid flux cover composed of 43 percent silica, 17 percent burned limestone, and 40 percent fused borax. Less successful but nevertheless promising results were obtained with mixtures of steam and hydrogen which were sufficiently selective at temperatures between 600° and 950° C. but did not result in complete oxidation of iron. Carbon dioxide-carbon monoxide mixtures also oxidized iron selectively but incompletely. Both stern and carbon dioxide systems produced sufficiently encouraging results to additional research on these systems.

Jan 1, 1961

By Clarence Hall, J. J. Rutledge

Many of the fatal accidents in coal mines have resulted from the Explosives used in Use of explosives for breaking down the coal. These accidents have resulted both from the use of explo- sives that were not suitable and from the careless or improper use of suitable explosives. Investigation has shown that one of the commonest causes of dis- astrous explosions in the coal mines in this country has been a blown- out shot of black blasting powder or dynamite. The dangers that attend the use of these explosives were perceived several years ago, and in consequence the attention of powder manufacturers was directed to the production of explosives that would be less liable to ignite inflammable gas or dust. The manufacturers have been so successful in their efforts that it is now possible to obtain explosives which yield much shorter and quicker flames than black blasting powder or dynamite, and hence are much less dangerous to use in fiery or dusty coal mines. of explosives. To find out which of the many grades of short-flame explosives Government tests have the qualities that render an explosive most effective and least dangerous for mining coal, the United States Government established a testing station at Pitts- burgh, Pa., in 1908. This station is now under the charge of the Federal Bureau of Mines. Before the station was opened a state- ment of the requirements that the explosives in question would have to satisfy was drawn up and sent to manufacturers. A number of these sent explosives to be tested, and on May 15, 1909, a list of the explosives that had passed the tests was published. Since that date other brands of explosives have been tested and three more lists have been issued. The latest list, published in Miners' Cir- cular 2, Bureau of Mines, contained the names of no less than 71 explosives that had passed the tests prior to January 1, 1911.

Jan 1, 1912

By Robert A. Jankowski

The Bureau of Mines has recently identified five major factors that contribute to high respirable dust levels on the six U.S. longwall faces having the most difficulty complying with Federal dust standards: (1) a poorly structured cutting sequence, (2) a poorly designed external water spray system, (3) marginal waterflow to the cutting drums, (4) minimal controls at the stage loader and crusher, and (5) the lack of effective controls for dust generated during support advance. The results of this survey illustrate the need to address all the major sources of longwall dust generation and the need for mine operators to implement a variety of control procedures to assure compliance. The Bureau of Mines will continue to assist mine operators in implementing improved dust controls and will work to identify and evaluate controls for dust generated during support advance.

Jan 1, 1983

By R. L. Crosby

A part of the liquidus of the magnesium-zirconium system was determined by chemical analysis of suction samples taken from the melt in the approximate temperature range of 850° to 1,450° C. The melt was prepared in a furnace pressurized with an inert gas. The average zirconium value in weight-percent of the liquidus composition at each sampling temperature was 0.96 at 867° C, 1.40 at 1,062° C, 2.05 at 1,262° C, and 2.96 at 1,402° C. The equilibrium solid phase was zirconium.

Jan 1, 1965

By M. B. Cooke, A. D. Bauer, E. W. Dean

The Bureau of Mines is collecting and analyzing representative samples of crude petroleum from all the producing fields in the United States , and the results are being published in a series of reports that are preliminary to the issue of a bulletin covering the entire survey . The bureau has recently completed a survey of crude oils from the Kansas district . In all 27 samples were collected and analyzed , under the direction of A. W. Ambrose , chief petroleum technologist of the Bureau. Valuable assistance was received through the cooperation of oil companies operating in the State , especially the Prairie Pipe Line Co. , and the Empire Pipe Line Co. The present report issued as Serial 2322 , on the Kansas crudes , forms the fifth of the series . Of the four previous papers , the first ( No. 2202 ) deals with crudes from the Eastern fields of the United States , the second ( No. 2235 ) with crudes from the Rocky Mountain district , the third ( No. 2290) gives additional data , cn viscosities and pour tests , for the crudes from these two fields , and the fourth ( No. 2293 ) covers the fields of northern Texas , northern Louisiana , and Arkansas . The details of the methods of collecting samples , making laboratory tests and interpreting results , have been discussed in these earlier reports . It has also been pointed out that the only adequate method of interpreting analyses of crude oils is to compare the individual reports with the analysis of some crude oil that is familiar to the operator . For this reason , no comprehensive discussion of the results of the Kansas survey is attempted, although some general statements may be made .

Feb 1, 1922

By Edward F. Divers

Tills U.S. Bureau of Mines report briefly evaluates the advantages and disadvantages of basic dust control techniques presently used by U.S. coal preparation and mineral processing plants. These include ventilation, baghouse-type collectors, wet scrubbers, electrostatic precipitators, source control, sprays, good housekeeping, and personal protection devices. Two specific problems in these types of operations are also considered: dust collector system duct clogging, and control room dust control. Information provided in this report results from dust control research projects conducted by the Bureau at various coal preparation and mineral processing plants over the past decade to reduce workers' dust exposure. These studies indicate that plant ventilation systems normally provide the most cost effective method for dust control. Baghouses and scrubbers were also effective in specific applications, and examples of each are given. In extreme dust conditions, personal protection devices, such as respirators or the dust helmet, can also be highly cost effective.

Jan 1, 1990

By James W. Townsend

[The Harrington-Hickory mine in the Star raining district, Beaver County, Utah, has produced approximately 20,000 tons of lead-zinc-silver ores since 1910. Production previous to 1910 is not known. The mine is owned by the New Majestic Mining Co. The property was rehabilitated and operated by James D. Williams under a 10-year lease with option to purchase from April 1943 to May 1949, Loans from the Reconstruction Finance Corporation in the aggregate of $41,000 wore used in construction of an access road, rehabilitation of the mine, and purchase of equipment for full-scale operation. The improved, all-weather access road extends from loading ramps on the Union Pacific Railroad at Milord to the urine storage bins 5 miles west o f town. The mine is serviced electrically by a. 5,000-volt line owned by Telluride Power Co. Mine transformers step the voltage down to 440/220/110 for surface and underground service.]

Jan 1, 1953

By R. W. Smith

The Bureau of Mines has been engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies were designed to provide basic thermodynamic information of high accuracy, facilitating the theoretical study of flame and combustion phenomena.4 This report is the fifth of a series5/ presenting results of the study for particular fuel-oxidant systems. These calculations have as their objective the constant pressure flame temperature of acetylene-air for a range of pressures.

Jan 1, 1954

By G. L. Hopps

Various chemicals, including compounds of copper and lead, were added to a mixture of No. 2 and No. 6 fuel oils that was fired in an experimental furnace. Tests were made to determine (1) the effectiveness of these chemicals in removing soot deposits on probes devised to simulate heat-transfer surfaces in boilers and (2) the effectiveness of the chemicals in preventing the deposition of soot on the probe surface. Test conditions were regulated so that the temperature of the products of combustion adjacent to the probes was in the range of 625° to 700° F. The clean-metal temperatures of the air-cooled probes were comparable with the water-tube temperatures in boilers operated at 40 to 100 p.s,i.g. The dosages of the fuel oil additives used in these tests were generally larger than those usually recommended for most proprietary compounds.

Jan 1, 1962

By N. F. Le Jeuns

For a number of years the Bureau of Mines has conducted semi-annual surveys to determine the changes in motor gasoline being sold in the United States. It was pointed out in the previous survey that there was an apparent tendency toward greater uniformity in the character of gasoline marketed in the United States. This practically uniform tendency which continued from April, 1917 to January, 1923, has been interrupted in the, present survey, as shown by an examination of the column marked "Difference," as given in Table 1. The figures in this table were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10% ,(85 samples) having the highest end points and the 10% having the lowest end points mere grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10%" and the ?Minimum 10%? respectively. The same process was used on the other surveys.

Jan 1, 1923