Search Documents

By G. St John Perrott

"The United States Bureau of Mines is cooperating with the State of Utah and the City of Salt Lake in an investigation of methods of abating the smoke nuisance in Salt Lake City. In the course of this work samples of the atmosphere have been collected and analyzed in an attempt to determine the part played by sulphur dioxide or smelter gases in polluting the air at Salt Lake City.A fairly wide-spread opinion exists in Salt Lake City that the smelters contribute appreciably to the smoke nuisance. The gases discharged from the smelter stacks are believed (1) to float over the city in a heavy blanket which prevents the smoke from rising, and (2) to unite with the water vapor in the air to form corrosive fogs injurious to health and property.The first of these theories seems untenable. If the gas did not mix with air it would sink, owing to its heavier specific gravity, and form a blanket an the earth. Actually, the gas diffuses rapidly in air and any part reaching Salt Take must he thoroughly diluted. Perhaps sulphur dioxide in sufficient concentration might aid in fog formation. The more obvious nuisance, however, would be the injury to health and vegetation.The Garfield smelter is 16 miles west of the city, The Murray smelter 8 miles south, and the Midvale smelter 12 miles south. Under normal operating conditions, a relatively small amount of solid matter is discharged from these stacks. The toxic gaseous constituent of the discharge is sulphur dioxide, it is being discharged from the smelters the year round. If they are a factor in the city's smoke problem, the concentration of this gas in the air of the city should be appreciable and should increase toward the smelters, the con centration being highest with a south or a west wind."

May 1, 1920

Reduce longwall shearer operator's dust exposure by selecting the best drum water spray sys-tem for minimizing dust generated durinq cutting. Approach Three of the most commonly-used drum water spray systems were installed on the same set of shearer drums and compared to determine which system best suppresses dust. The spray systems studied were: ? pick-point flushing ? cavity filling ? water-through-the-it Instantaneous and gravimetric sampling instruments were used to measure the respirable dust exposures of the shearer operators and dust concentrations downwind of the shearer. The Three Systems: Longwall shearer drums are routinely equipped with internal drum spray systems since these systems have been shown to be more efficient than external systems in terms of dust suppression per gallon of water applied. All U.S. longwall shearer faces utilize some type of internal water delivery spray system. The two most common systems are bit-or pick-point flushing and cavity filling. Pick-point flushing uses nozzles mounted in the bit blocks or in special blocks immediately in front of the bits. Cavity filling utilizes spray nozzles installed in a pipe manifold mounted on the drum hub between the scrolls or along the edge of the vane scrolls; water is sprayed radially from the manifold towards the adjacent vane scroll.

Jan 1, 1986

By Robert C. Hickman

"INTRODUCTION The Big Four fault and the Sandy Creek fault, with several cross faults, traverse the Stalion-Curnel fluorspar prospect in a northeasterly direction. The Big Four mine, about three-quarters of a mile northeast of the prospect, is the only active mine in the immediate area.A resistivity survey was made of a portion of the prospect by the Division of Geophysical Exploration, Bureau of Mines, in May and June 1946. As a result of this survey, five holes were drilled by the Bureau of Mines during the period from October 8 to December 16, 1946. Two Longyear No. 12 Junior Straitline diamond drills were used for the work.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the supervision of Mitchell H. Kline, chief, Raleigh Branch, Mining Division."

Mar 1, 1948

By D. Harrington

Although it is impossible to give definite final figures at this time on Nation-wide accident occurrence in 1933 , enough data are at hand to indicate that the progress in safety in the mining industry, which first became apparent in 1930 and was accentuated in 1931 and 1932 , was continued and much improved in 1933. This improvement was of considerable magnitude in mining both bituminous coal and anthracite but was not so great in other branches of the mining industry . While the volume of work done in all phases of mining increased in 1933 over that in 1932 , the exact amount of the increase is not yet known . Usually increased activity in mining is accompanied by even greater increase in the rate of occurrence of accidents to the workers , but happily it appears that this " rule " was not operating in 1933 --at least in the coal -mining industry .

Oct 1, 1934

By Charles W. Huggins

Electron diffraction and electron microscopy were used to determine the unit cell parameters of garnierite [(Ni,Mg)3 Si2O5 (OH)4] and to examine its crystal habit. Bundles of ribbons, many less than 200 A. in cross section, make up the bulk specimen of the garnierite Electron diffraction revealed the unit cell to be monoclinic. Unit cell parameters were: a, 5.33 A,; b, 9.23 A.; c, 14.96 A.; and ß, 94°441.

Jan 1, 1961

By Frank D. Lamb

Four samples of manganese-bearing material from the Aroostook County, Maine, deposits were tested at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., to determine their amenability to beneficiation by ore-dressing methods. The samples represented material from the Maple Mountain-Hovey Mountain deposit, the Dudley farm, and the Burnham farm and contained 11 to 14 percent manganese. None of the tests produced appreciably enriched concentrates suitable for further treatment for the production of ferromanganese. The intimate association of the manganese minerals with iron and siliceous minerals requires extremely fine grinding to liberate the manganese minerals in these ores and prevents efficient concentration by physical means.

Jan 1, 1953

By Will H. Coghill

[The supply of gravel spar and of acid spar is not well balanced. Gravel spar -- 85 per cent flourspar, 5 per cent silica -- gluts the market, whereas acid spar -- 98 per cent fluorspar, 1 per cent silica -- is somewhat scarce. Hence it is desirable to convert some of the gravel spar into acid spar. Knowledge of this condition prompted the Franklin. Fluorsrar Co. at Paducah. Ky., to enter into cooperation with the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy to improve the methods of fluorspar, milling so that morn acid spar would be available. The fluorspar company detailed Mr. Omar Greeman for the work. During the course of the investigation, while Mr. Greeman was also doing work for a master's degree in the School of Mines? an extensive study was made of gravity concentration of fluorspar ores. Decrepitation by heat treatment was also given a laboratory try-out. A part of tie time was spent on flotation; these notes relate only to the flotation. The results of one of the flotation runs is appended. The test was made in a 500-gram mechanical-agitation machine. The sample was ground to 100-mesh in a pebble mill.]

Jan 1, 1928

By Frederick C. Trutt

Research performed on arcing faults and their interaction; with electrical insulating materials within coal.-mine power-system enclosures is described. This work was performed at The Pennsylvania State University from 1 December, 1976 through 30. November, 1977. Results presented are interim in nature and future research is planned to integrate the simulations which have been constructed, as well as to apply developed experimental procedures to the evaluation of electrical insulating materials for use in coal-mine enclosures. The thrust of this research has been divided into several primary areas. These include the development of a theoretical procedure for computation of three-phase and line-to-line arcing fault currents as a function of time, formulation of an arc model based upon thermal-arc plasma properties so that arc voltages and energies may be computed, development of a simulation for pressure and temperature rises when an arc interacts with an electrical insulating material within an enclosure, experimental evaluation of electrical insulating materials in terms of their tendency to support an arc as well as their potential contribution to enclosure pressure rises, and integration of the above research areas to form overall procedures for theoretical and experimental evaluation.

Jan 1, 1977

By J. G. Donaldson

Binary alloys of molybdenum and tungsten were prepared by the Bureau of Mines in laboratory-scale experiments by hydrogen reduction of their vaporized hexafluorides. Near-optimum deposition parameters were determined, and the nature of the deposited alloys was investigated. Dense, homogeneous alloys were codeposited between 650° and 750° C with a reduction efficiency of more than 75 percent. The alloy composition was uniform when the hydrogen ratio in the gas feed mixture did not exceed 3 times the stoichiometric requirement. Regulating the proportions of the metal hexafluorides in the gas feed provided a large degree of control over the composition of the deposit. Hardness of the deposits varied directly with the proportion of excess hydro,,,, in the gas feed and with the weight-percent of tungsten in the alloy. Hardness was not affected by deposition temperature over the range 650° to 750° C for specimens of similar composition. Extreme brittleness and unsuitable physical shapes of the alloys prevented tensile strength measurements.

Jan 1, 1966

By Aleksandar D. Bugarski

Three types of uncatalyzed diesel particulate filter (DPF) systems, three types of high-temperature disposable filter elements (DFEs), and one diesel oxidation catalytic converter (DOC) were evaluated in underground mine conditions for their effects on the concentrations and size distributions of diesel aerosols. Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. The DPF systems reduced total mass of aerosols in the mine air approximately 10-fold for light-load and 20-fold or more for high-load test conditions. The DFEs offered similar reductions in aerosol mass concentrations. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the filter element. The effectiveness of DPFs and DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. The effects of the DOC on mass and number concentrations of aerosols in mine air were relatively minor when compared to those of the DPF and DFE systems.

Jan 1, 2009

By W. H. Rinkenbach, C. A. Taylor

"Among the recently patented detonating compounds that have been suggested as substitutes for the commonly used fulminate of mercury is the normal lead salt of trinitroresorcin, or styphnic acid. As no data concerning its use or practi¬cability were available, a study of its properties was made in the explosives laboratory at the Bureau of Mines experiment station at Pittsburgh, Pa. This paper embodies the results obtained.Normal lead trinitroresorcinate was first prepared and patented*** by Herz; it probably found some use during the World War, but no record of its performance is available,Preparation of Lead Trinitrpresorcinate.In his patent specifications, Herz states that the normal salt may be obtained in a quantitative way by precipitating a multiple of the equivalent weight of the lead salt of a strong inorganic acid - such as lead nitrate - in the presence of a weak organic acid - such as acetic acid - by heating with a Teak solution of the alkali-metal salts or alkaline-earth salts of trinitroresorcin. Herz gives the following example: 245 grams of dry trinitroresorcinand 290 grams of crystalline sodium carbonate are dissolved in in 18.8 liters of boiling water, to which 77 c.c. of glacial acetic acid is added. The toiling solution is mixed with a boiling solution of 650 grams of lead nitrate in 1.4 liters of water, stirring rapidly; and the mixture is boiled for two minutes, after which it is cooled quickly with constant stirring. The precipitated crystals are then filtered off, washed several times with cold water, and dried."

Oct 1, 1923

Develop a reliable, portable device for non-destructively testing the support integrity of a friction rock support (commonly referred to as a Split Set ). Approach The friction rock support, used to support mine roof and ribs, is a slotted tube driven into a drilled hole of smaller diameter. Upon installation, the tube is compressed radially. The amount of compression is a function of the hole diameter, the strength of the host rock, and the properties of the split set itself. A simple lightweight self-contained device was developed to determine the pull-out resistance of the friction rock supports in-situ, based on measurements of the tube's deformation. The tester measures the com-pressed internal volume of the slotted tube, which has been found to provide an estimate of the support's resistance to pull out. How It Works The tester consists of a pump and expander sections. The expander sections are made from an elastomer membrane which is stretched over two cores, each one inch in diameter and twelve inches long. The expanders are connected by a flexible coupler so that they can fit any alignment of the support.

Jan 1, 1984

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

"INTRODUCTION The float-and-sink test 5/6/ is generally the first test used in determining the washing characteristics of coal. The simplest form of the test is that of using one solution of such specific gravity that the test sample is separated into ""float"" and ""sink"" fractions. In practice, however, a series of solutions is used, and the sample is separated into a number of fractions of a definite specific-gravity range. Analyses of a series of fractions of this type are often referred to as the ""specific-gravity analysis,"" and are of great value in the selection, construction, and operation of commercial washing equipment.The test is rather simple to use, provided a number of conditions are recognized and as many as possible held constant, such as:1. In laboratory testing, two types of solution are available -Aqueous solutions of calcium and zinc chlorides.Mixtures of organic liquids such as carbon tetrachloride, benzene, gasoline, bromoform, etc.2. Absorption of the solution by the coal,3. Solvent action of the solution toward the coal.4. Constancy of specific gravity during the test is affected by temperature changes, dilution, and evaporation.5. Personal technique of the test, such as the time the coal is in the liquid, rate of adding the sample to the liquid, stirring, time of draining, etc.6. Moisture content of the coal as tested."

Dec 1, 1947

By Richard A. Winters

The 31,880-acre Battle Creek Wilderness Study Area (WSA) was evaluated for mineral resources by the U.S. Bureau of Mines in 1984. No mining district is in the area, nor were any mines or claims recorded or found. Oil and gas leases, or lease applications, covered about half the area in early 1984. No known exploration has occurred. The entire WSA is covered with thick volcanic flows. Faults in these volcanic rocks may have provided conduits for mineralizing solutions emanating from the basement rocks; however, no evidence of mineral deposits was detected from rock samples collected along the faults. Reconnaissance samples from sand and gravel deposits yielded gold at less than $0.02/yd3. The source of the gold is assumed to be intrusive rocks or the Challis Volcanics about 20 miles north of the study area near the headwaters of Battle Creek. No economic concentrations of minerals were found in the WSA. INTRODUCTION Mineral surveys of designated wilderness study areas (WSAs) 1/ are conducted by the U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) at the request of the U.S. Bureau of Land Management (BLM). The USBM researches the mining and mineral exploration history and evaluates mines, prospects, and mineralized areas within or adjacent to WSAs. The USGS studies WSAs by regional geochemical and geophysical surveys and geological mapping. The USBM and the USGS investigations are summarized in a joint report used to help determine the suitability of WSAs for inclusion into the National Wilderness Preservation System. Although the immediate goal of this USBM study is to provide data for the President, Congress, BLM, and the general public for land-use decisions, the long-term objective is to help insure that the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1985

The Ringelmann Smoke Chart fulfills an important need in smoke abatement work and in certain problems in the combustion of fuels. A knowledge of its history and method of preparation is, therefore, of interest to many. Since instructions on its use are not shown on the recent edition of the chart, those included in this revision of the previous Bureau of Mines publication now are a necessary complement to the chart, More detail regarding the use of the chart is included than was given in the earlier version.

Jan 1, 1967

By I. D. Shah

The Bureau of Mines investigated the sequence of principal chemical reactions taking place during the roasting of covellite (CuS). Practically all covellite is converted to digenite (Cul.SS) before oxidation to Cu20 begins. Part of the Cu2O is then converted to CuO, which in turn forms CuS04 through CuO?CuS04 as an intermediary. CuS04 and CuO'CuS04 decompose at 600° to 700° C to yield CuO and S03 (g) as final products. An overall mechanism is proposed for chemical reactions occurring at different interfaces of partially oxidized CuS pellets.

Jan 1, 1970

By J. P. McGee

As part of a joint U.S. Atomic Energy Commission-Federal Bureau of Mines program for using nuclear energy to supply process heat, a simulated nuclear loop has been constructed to test components. This loop has been operated for more than 1,800 hours at 100 p.s.i.g. Of this period, 23 hours were at 2,500° F. and higher; 540 at 2,000° to 2,500° F.; 840 at 1,500° to 2,000° F.; 200 at 1,000° to 1,500° F.; and 260 below 1,000° F. Leakage at flanges and welds was not a serious problem. A helium-recycle system with gas temperatures of 2,300° to 2,500° F. and a static pressure of 250 p.s.i.g. appears feasible. Difficulties were encountered with the recycle compressor due to thermal distortion of the impeller and shaft. The use of sealed bearings limits compressor operation to the life of the bearings.

Jan 1, 1960

By R. V. Lundquist

A method was developed by the Federal Bureau of Mines for evaluating viscosity data from slurries obtained in leaching sinters from the lime soda sinter process for extracting alumina from aluminous silicates. The logarithm of the viscosity was observed to be a linear function with time. The slope of the plotted line provides a means for evaluating viscosity behavior in a lime soda sinter blurry and also a means for comparing gelation characteristics directly with other variables in the lime soda sinter process. This report presents one aspect of a continuing study by the Bureau of Mines on methods for treating siliceous aluminum ores. It is one of the many programs of the Bureau concerned with conservation, development, and use of our domestic minerals resources. Previous investigations of lime soda processes, both by the Bureau4-7/ and industrial concerns, have demonstrated that sintered materials containing CaO, Na2O, A1203, and S102 in various combinations exhibit a tendency to gel or set when mixed with water or other extraction solutions. Gelling prevents satisfactory recovery of alumina and in extreme cases prevents operation of an extraction plant.

Jan 1, 1960

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008, "I guess that without the occasional complaint, your mine is probably over-ventilated" (Marks, 2008). Miners are seldom in this situation and spend much of the time trying to find enough air to keep an operation running. With examination, there are usually changes that can be made to increase the efficiency of ventilation systems. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Modifications that result in surplus mine ventilation air could bring financial and environmental benefits. Some issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and nonmetal mines, to ventilate reserves that are deeper, hotter, and further away from fans and shafts, and to meet demands from increased production. This paper discusses successful methods to find additional usable air when there is no extra ventilation capacity. Most of the options presented in this paper are useful for metal/ nonmetal operations but some may be applicable to coal as well.

Jan 1, 2010

By R. G. Nelson

The mechanical properties of low-hafnium, arc-melted, Kroll-process zirconium are presented. The effect of temperature on the ultimate strength, yield strength, proportional limit, elongation, hardness, Young's modulus, electrical resistivity, and impact strength are shown, The effects of cold work and annealing on the tensile properties, bend radius, and formability, as determined by cupping tests, are also given, Tensile properties are compared, in part, to those obtained on earlier graphite-melted zirconium and on crystal-bar zirconium. INTRODUCTION The commercial production of high-purity, low-hafnium bearing zirconium has been achieved, and this metal is becoming available for industrial use. However, there is little published information regarding the physical and mechanical properties of this product; and, since there have been many improvements in the production and arc-melting techniques of zirconium in the past 3 years, it was considered advisable to present the properties of the vastly improved zirconium representative of current production.

Jan 1, 1954