Search Documents

By D. E. Anders

Saturated hydrocarbons from 60 selected samples of a 2,300-foot Green River Formation oil-shale core (Piceance Creek Basin, Colo.) were analyzed by gas-liquid chromatography techniques. Emphasis was placed upon the distribution of normal alkanes and 15 key-branched and cyclic alkanes. The latter compounds consisted of the C15, C16, C18, C19, and C20 chain isoprenoids, the 5-a and 5-ß C27, C28, and C29 steranes, three C30 pentacyclic triterpanes, and perhydro-ß-carotene. The results showed definite evidence of maturation of both the n-alkanes and the branched and cyclic alkanes; however, most if not all of the changes were limited to the indigenous soluble extract and were not the result of additional soluble extract generation from the insoluble kerogen. Source material and environmental variations were important factors in some of the observed differences in the branched plus cyclic alkane compositions.

Jan 1, 1973

By W. S. Landers

In contrast to the large fund of information available on the carbonizing properties of Eastern U.S. coals, the experimental data available for most Western U.S. and foreign coals are meager. To supply some self-consistent data, the Bureau of Mines conducted 220 low-temperature carbonization assay tests at 500° C. in a laboratory-scale carbonization apparatus. The results are included in this report. The U.S. coals tested are from Alaska, Arizona, Colorado, Illinois, Montana, New Mexico, North Dakota, Pennsylvania, Ohio, Texas, Utah, and Wyoming. Assays were also made on coals from Canada, Ecuador, France, Greece, India, Mexico, the Philippine Islands, Thailand, and Yugoslavia. In addition, one assay of pine sawdust and one assay of a peat from Ireland are reported. Prediction equations were developed relating the yield of products of carbonization obtained at 500° C. in the assay unit to the proximate and ultimate analyses of the coals. The equations for predicting the yields of tar plus light oil, char, and gas, and the heating value of the gas, are considered good, each equation having a multiple correlation coefficient of 0.90 or higher. The equation predicting volume of gas obtained upon carbonization is considered as fair, with a multiple correlation coefficient of 0.84. A reproducibility study of the assay made on 10 replicate samples of a subbituminous coal indicated that the standard deviation of the individual products was 0.31 percent or less.

Jan 1, 1961

By Robert K. Koch

Laboratory-scale studies on defluorination of natural and synthetic fluorspars by pyrohydrolysis at 1,500° C. were made to determine the feasibility of developing a process for producing hydrogen fluoride from siliceous fluorspars. It was found that the reaction (at 1,500° C.) is not promising for process development, even though a silica-free offgas can be generated. The primary difficulty is the low hydrogen fluoride content of the offgases; an HF content of 6 percent was the best achieved. Previous research by the Bureau of Mines has demonstrated that offgases averaging 27 percent hydrogen fluoride can be produced under carefully controlled conditions at 1,280° C. The lower temperature process is a better method for production of HF. However, charges in which the CaF to Si02 mole ratio varied from 0.4 to 2 could be processed with similar results. Also, combined alumina and ferric oxide contents up to 25 mole-percent did not noticeably alter the rate of defluorination. Therefore, virtually any natural siliceous fluorspar would respond in essentially the same manner when exposed to water vapor at 1,500° C.

Jan 1, 1962

By D. R. Babich, E. R. Bauer

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of equipment sound levels and worker noise exposures in the stone/aggregate mining industry. Six stone/aggregate mines (three surface and three underground) were recently surveyed, and the findings (ire presented here. The surveys consisted of sound-level measurements conducted around various equipment and machinery (including stone processing and crushing equipment) and full-shift dose measurements to determine worker noise exposures. The findings identify the equipment and machinery that are likely to cause worker overexposures and identify the workers found to he experiencing overexposures. In addition, the benefit of cabs in reducing mobile equipment operator noise exposure is discussed.

By John Henderson

If you missed this year?s Texas State Holmes Safety Association meeting, you missed a great one. On January 23 & 24, 2009, we held the meeting that was rescheduled when Hurricane Ike threatened Corpus Christi in September 2008. Sixty-five persons from across the state attended the meeting held at the Holiday Inn Emerald Beach. The weather was 82 degrees, and the sky was clear and perfect for a safety meeting. Evaluations submitted by the attendees gave the presentations, the networking, and even the food top marks. There were eight councils represented; Big Country, Central Texas, Costal Bend, Heart of Texas, Hill Country, North Texas and North Central. Presentations included Workplace Examinations, Emergency Preparedness, Screen Safety, Contractor Responsibilities, Powered Haulage, Supervising for Safety, and Basic Inspections of Slings and Rigging. Mr. Edward Lopez, SC MSHA District Manager, gave the State of the District Address.

Feb 1, 2009

By Thomas E. Green

A solvent extraction procedure using 8-hydroxyquinoline and chloroform was investigated by the Bureau of Mines as a preconcentration technique for the determination of aluminum, calcium, cobalt, copper, iron, lead, magnesium, manganese, nickel, and zinc in large samples of high purity tungsten. X-ray spectrographic and atomic absorption methods were used to determine the trace metals after preconcentration. The presence of 10 grams of tungsten had a pronounced effect on the distribution of 8-hydroxyquinoline between the aqueous and chloroform phases. This change in the 8-hydroxyquinoline distribution in turn had an adverse effect on the extraction of the trace metals. Extraction efficiencies can also be adversely affected by an increase in the quantity of extractable metals present, as shown by radiotracer tests using 65Zn. Excess 8-hydroxyquinoline in the extracts did not interfere with the determination -of the serious interference in the combined ion exchange paper--X-ray spectrographic method. Although preconcentration by 8-hydroxyquinoline extraction was found to be partially successful, other preconcentrationn methods based on ion exchange and dithizone extraction were found to be superior.

Jan 1, 1968

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

By Albert L. Brautigam, Michael C. Leigh, August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 1992

By E. Chin

The production of crude mineral commodities in Bangladesh was limited to natural gas, a small amount of construction materials, and clay for ceramics and bricks. No metallic minerals were mined. The only mineral commodity of economic significance was natural gas. Natural gas production has 'been climbing steadily and becoming an increasingly important source of energy for the country. Proved gas reserves were over 4.5 trillion cubic feet, but the amount has been increasing as exploration discovers large new deposits. Some sources quote reserves at over 10 trillion cubic feet.

Jan 1, 1984

By R. R. Hornor

BIBLIOGRAPHY OF ARTICLES RELATING TO THE PRESERVATION

Apr 1, 1922

By M. Kanefsky, A. Q. K. Rajput

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties but on the precise shape of the cross-correlation functions between the noise inputs. By using two polarity difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 11, 1981

By Manuel Gomez

A general prediction model for the Hardgrove grindability index was constructed from 735 coal samples using the proximate analysis, heating value, and sulfur content. The coals used to develop the general model ranged in volatile matter from 12.8 to 49.2 percent, dry basis, and had grindability indexes ranging from 35 to 121. A restricted model applicable to bituminous coals having grindabilities in the 40 to 110 range was developed from the proximate analysis and the petrographic composition of the coal. The prediction of coal grindability within a single seam was also investigated. The results reported support the belief that mechanical properties of the coal are related to both chemical and petrographic factors of the coal. The mechanical properties of coal may be forecast in advance of mining because the variables used as input to the prediction models can be measured from drill core samples collected during exploration.

Jan 1, 1970

By K. Robert Dorman

This Bureau of Mines report describes laboratory and field experimentation in building mine ventilation stoppings, air-door frames, and fan bulkheads with a civil construction technique. Shotcrete is applied to a free-standing, three-dimensional wire-truss panel, which is easily cut and rapidly erected. In mines where shotcrete equipment is available, this technique should be faster and cheaper than conventional block-and-mortar or monolithic concrete construction.

Jan 1, 1980

By Fred C. Turin, William J. Wiehagen

This study examined musculoskeletal injury risk at four mining sites: underground coal, underground limestone, surface copper, and surface phosphate. Each site offered opportunities to investigate musculoskeletal disorder (MSD) injury risks and how those risks might be identified and categorized. The National Institute for Occupational Safety and Health (NIOSH) worked with these sites to (1) identify work activities that showed evidence of MSD injury risk, (2) examine physical risk factors that can lead to MSDs for a handful of work tasks at each site, and (3) develop a set of ideas for problem-solving to help reduce risk factors for examined work tasks. For each site, NIOSH implemented a plan that was refined over the time period of this study. The plan consisted of four steps. The first step was to use mine injury records, a musculoskeletal discomfort questionnaire, front-line supervisor interviews, and a list of management concerns to identify work groups and work activities that have significant evidence of MSD risk factors. The second step was to select work tasks for evaluation. The third step was to interview those who do the work and make observations to characterize the MSD risk factors and musculoskeletal symptoms that exist for target tasks. The final step was to conduct brainstorming sessions with workers who perform the work or have a stake in the production task. The brainstorming sessions served to identify general strategies (ideas) for reducing MSD risk factor exposures. A final report of findings was presented to mine management and workforce representatives at each site. The risk factors and ideas for improvement identified for each site were specific to the target tasks examined. These target tasks were diverse, but there were some key similarities. For instance, jobs were found at each site that required a significant amount of manual work involving the upper extremities and low back. Handling heavy and awkward objects, forceful arm and shoulder exertions, and working in awkward postures were common for a variety of jobs across the four sites.

Jan 8, 2004

By John Ward Smith

The Bureau of Mines drilled Wyoming Corehole No. 1 in Sweetwater County, Wyo., to sample Green River Formation oil shale. Core obtained was assayed for oil yield to determine richness and stratigraphic distribution of oil shale in the deposit. Oil shale in place at Wyoming No. 1 site represents over 200 million barrels of oil per square mile. Additional data useful in evaluating the deposit, including generalized stratigraphy and mineralogy, detailed lithologic descriptions of the core, rock specific gravity, and bore-hole logs, are presented with the oil-yield data. The sampled Wyoming oil shale resembles Mahogany-zone oil shale in rock properties and gross mineralogy. A statistically derived equation relating shale density to oil yield for the Wyoming deposit compares with a similar relationship valid for the better known Mahogany-zone oil shales in Colorado and Utah. A density log from Wyoming Corehole No. 1 is calibrated for direct oil-yield logging. The alternating rich and lean beds of shale at this site may permit creating the permeability necessary for direct production of shale oil from the shale in place.

Jan 1, 1968

By Walter E. Lewis

Ventilation-air-heating plants are in use at several iron mines on the Menominee Iron Range, Iron River, Mich. Many of the mines are exceptionally wet; during winter months, when fresh air is forced down the wet air shafts into the mine, it is usually necessary to heat the fresh air to above freezing so that the openings will not be closed by ice. The problem of ice closing air shafts has been solved by the practice of reversing the air current before the openings have become completely closed. This procedure involves drawing warm air from the mine up the usual down-draft air shaft. The M. A. Hanna Co. has found, at some of their mines on the Menominee Range, that it is more convenient to heat the below-freezing air rather than reverse the air current. Intermittent freezing and thawing of ice that has formed in the air shaft tends to loosen the wall rock, requiring major shaft repairs. The openings are kept free of ice the year around by heating the fresh air during periods of below-freezing weather. Table 1 shows the monthly minimum moan, maximum mean, and mean temperatures for the Iron River area. Under normal conditions of temperature, the furnaces are fired in November and usually are not allowed to go out until April of the following year.

Jan 1, 1951

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

Provide a means of recovering precious metal values from finely ground tailing materials. Approach Determine the procedures needed for agglomerating the finely ground material for subsequent heap-leach cyanidation of the precious-metal-bearing tailings. Applying Agglomeration/Heap-Leaching to Fine Tailings Agglomeration technology was developed by the Bureau of Mines to provide cost-effective recovery of precious metal values though better heap leaching of clayey or low-grade ores. While many precious metal producers have adopted this technology to reclaim precious metals from crushed ores and wastes, other operations have experienced problems in using the heap leaching technique effectively on piles of fine tailings. In contrast to the coarser ore and waste material, most tailings piles contain more than 50 percent minus 200 mesh materials with no coarse material. Fine particles and clays present in the pile can impede 8 uniform flow of the leaching solution through the heap, thus preventing efficient and cost-effective precious metals recovery.

Jan 1, 1986

Control the release of ground-water into active underground coal workings by short-term pumping from dewatering wells sited on fractures. Approach The sudden release of fracture-stored groundwater into underground coal workings often occurs when mine workings are developed beneath fracture valleys, Pumping from fracture trace-sited dewatering wells, prior to development of the underlying workings, can be an efficient means of intercepting fracture-stored groundwater before it is released into the mine. Dewatering operations are discontinued once the underlying mine workings have been fully developed, and the maximum possible reduction in fracture storage has been achieved through pumping. How It Works An aerial photographic technique known as fracture trace analysis is used to site dewatering wells on rock fractures in a valley bottom. Downhole caliper and temperature logs are used to assess the fracture flow potential of each dewatering well drilled.

Jan 1, 1987

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of El Salvador has been prepared from the best available information in Washington , but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State . Under the terms of the Code of Commerce ( arts . 12ff . ) , foreigners living in El Salvador can engage in business on the same terms as nationals . This involves ( = $434.00 ) - except for those with a working capital , of less than a thousand pesos inscription in the merchants ' register , which can be refused only in case of manifest disability of a permanent nature .

Sep 1, 1930