Search Documents

By Jeffrey Johnson, Thomas Brady, Radford Langston, Mary MacLaughlin, Hendrik Kirsten

The magnitudes and directions of in situ stresses affect the stability of mine openings, as well as the type and amount of ground support needed to maintain a safe working environment for miners. Using hollow inclusion stress cells, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health obtained two in situ stress measurements from the face of two footwall lateral drifts at the Stillwater Mine near Nye, MT. The first measurement, obtained in 1997, was collected under the valley beneath the Stillwater River. The second measurement was obtained in 2002 under the main frontal massif of the Bear tooth Mountains in the western sector of the mine. Although few data are available, the major principal stress under the valley has been recorded as nearly horizontal in a north-south direction perpendicular to the ore body, while beneath the mountains, stress runs east-west parallel to the ore body. This paper documents the measurements, describes the in situ stress state, and discusses a finite-difference analysis of the biaxial test.

By Philip W. Holland

The U.S. Bureau of Mines has developed an improved method for determining dissolved helium in water in the concentration range of 4.0 x 10-8 to 270 X 10-8 cm3 He (STP)/cm3 H2O. The method is a modification of a previously reported method that was developed for analrzing surface and subsurface waters in geochemical survey work. Water samples are collected in SOD-cm stainless steel cylinders, and the dissolved gases in a sample are extracted into an evacuated cylinder of equal volume. After addition of 30 psig of nitrogen containing less than 2 ppb helium to the extracted gases, the resulting mixture is analyzed for helium using a helium-tuned mass spectrometer. The helium content of the water sample is determined from an empirical calibration that is established by analyzing standard solutions of helium in water. The accuracy of the method is ±7 pct for helium-in-water concentrations above 10 x 10-8 cm3 He (STP)/cm3 H2O.

Jan 1, 1989

By M. D. Marshall

This handbook is for the engineer or person responsible for the storage and removal of material from bins and silos in the minerals industry. The objective of the handbook is to prevent bin-related accidents by eliminating problems which require workers to enter bins. It provides basic information on handling materials so that knowledgeable decisions can be made on bin design and accessories to minimize flow stoppages. Materials are classified in terms of their flowability, and bin design and accessories suggested for each classification. A method for classifying a material is also given, and the various types of material flow aids reviewed. Safety around bins is the basic theme of the handbook. Federal regulations are reviewed and additional suggestions presented to prevent bin accidents. New equipment for releasing material hang-ups is reviewed.

Jan 1, 1984

Reduce the cost and incidence of low-back pain in underground coal mines through redesign of materials-handling tasks. Background Approximately 25 pct of all injuries in mining involve trauma to the hack. These injuries account for at least 30-40 pct of worker compensation payments made by the industry, are the leading cause of lost work days in mining, and have been estimated to cost the industry $50 million annually. It is clear that the traditional approach to reduce back injuries (i.e., training) has been largely ineffective. Thus, new approaches are necessary to control this problem. This document briefly describes methods that can be used to redesign hazardous materials-handling tasks to reduce the threat of worker injury. Approach A model for redesigning materials-handling tasks is shown in figure 1. The model outlines the sequence of steps that should be followed (and questions that should be asked) when developing new strategies for handling materials in underground coal mines. A critical examination of the current supply-handling system is the first step to developing safer materials-handling procedures. The purpose is to identify hazardous tasks that can be modified to reduce injury risk. Accident analysis (a review of past accident records) and task analy¬sis (usually a videotaped analysis of hazardous jobs or tasks) arc effective methods of distinguishing areas where job redesign is needed.

Jan 1, 1992

By James J. Olson

The Bureau of Mines used micro fracture density analysis of quartz grains in thin sections and diametric pulse velocity measurements along preblast and postblast cores to determine the nature and extent of rock damage produced by small (0.25-,0.50-,1.0-, and 2.0-kg) charges of high intensity explosive (C-4) in granite. Pulse velocities from the postblast cores were significantly lower than velocities from the preblast cores and, with the core logs, provided clear identification of the upper and sometimes the lower limits of most severe damage. These zones ranged from about 1.68 ft for the 0.25-kg blast to 4.16 ft for the 2.0-kg blast. Microfracture densities from postblast cores were significantly higher and more variable than densities measured from preblast cores. The microfracture density measurements showed that microscopic damage was present far past the zones of most severe damage as delineated by the pulse velocity logs and core logs. An exponential relation-ship was observed between the micro fracture density levels and the charge weight.

Jan 1, 1973

By P. L. Woolf

Oil was successfully injected into the tuyeres of the Bureau of Mines experimental blast furnace. Determinations were made for the minimum oil addition necessary to permit the maximum available blast temperature of 2,250° F. and the maximum oil rates at blast temperatures of 1,900°, 2,000°, and 2,100° F. From these tests, the upper and lower levels of high-temperature heat input, which limit the smoothly operating furnace, were established. Substantial coke saving was realized with maximum oil injection. Oil-to-coke replacement ratios have been calculated for various conditions, and oil is compared with natural gas and moisture in somewhat general terms. A study of the effect of variations in slag volume and basicity on the sulfur content of the metal at high sulfur loads was made.

Jan 1, 1963

By Basil Dimitriades

Five recently developed methods for determining nitrogen oxides in automotive exhausts have been evaluated from the standpoint of accuracy and applicability in current exhaust studies. Results showed that methods requiring conversion of nitric oxide to nitrogen dioxide as a part of the analytical procedure are subject to errors introduced by the instability of NO2. The extent of some of these errors has been determined and procedures have been developed to minimize undesirable influences. On the basis of the results obtained from this study, recommendations are made regarding procedures for batch type or continuous measurement of nitrogen oxides in exhaust streams.

Jan 1, 1968

By Arthur E. Goddard

Radio propagation measurements were conducted in a coal mine at UHF (200 to 1000 MHz) and VLF (1 to 50 kHz) to characterize the transmission loss of intra-mine paths. The basic experimental parameters included frequency, polarization, path orientation and distance. Further tests evaluated the performance of roof-bolt vs. loop antennas at VLF and parasitic reflectors at UHF. Measurement results are summarized in a series of transmission loss curves. Examples are presented to show the use of these curves in predicting the performance of radio communication systems in mines.

Jan 1, 1973

By Murali M. Gadde, John A. Rusnak

Rock mass classification systems are extremely useful for site characterization and have been employed by the rock mechanics community for several decades. While empirical in nature, the classification systems provide a viable means to quantify the nature of rock mass, which is necessary for stability analyses. In U.S. coal mines, the Coal Mine Roof Rating (CMRR) is the most widely used classification system for several purposes, including sup-port selection, chain pillar design, assessing the stability of extended face cuts, etc. The Analysis of Roof Bolt Systems (ARBS) is an empirical method developed from the CMRR to guide selection of roof bolts as the primary support system in U.S. coal mines. In this paper, the experience of Peabody Energy in applying ARBS to sup-port design is discussed. In general, data from the Peabody mines show that ARBS predictions match well with field conditions. Peabody, however, does not use ARBS as the stand-alone methodology for support selection. Peabody uses a two-pronged approach in which the support requirement is initially estimated from the classification method, and then numerical modeling is used to select the proper reinforcement system. Such an integrated approach is necessary, as ARBS suggests only the “amount of steel” that may be used to support the roof and does not specify which type of roof bolt to use. A case study is used to demonstrate the usefulness of ARBS and Peabody’s integrated approach to support design. Also, the application of ARBS at several Peabody mines showed a very good correlation with support cost. The correlation indicated a direct relation between bolting cost and the ARBS value.

Jan 5, 2007

By N. S. Dalal, X. Shi, V. Vallyathan

"INTRODUCTIONThis paper summarizes our recent investigations of the potential role of silicon-oxygen based free radical species in the biochemical mechanism of the lung injury caused by the inhalation of freshly fractured silica. The impetus for this study came from the following observations. Inhalation of crystalline silica is associated with the development of acute and chronic silicosis. Chronic silicosis is characterized by the development of sharply marked concentric fibrotic nodules in the lung. This occurs over a period of several decades with the development of progressive respiratory impairment. In contrast, acute silicosis is manifested by the filling of the alveoli with an amorphous lipoproteinaceous exudate within a short period after exposure, and rapid development of respiratory disability often leading to fatality. Most studies on the pathogenesis of silicosis have focused on the elucidation of cellular mechanisms of cell injury and the development of chronic silicosis. Because pulmonary responses to crystalline silica are distinctly different for · the acute and chronic silicosis, we hypothesized that the acute response is associated with some unique properties of ·freshly formed silica particle surfaces, due to the formation of some reactive chemical species caused by the rupturing or the silicon-oxygen bonds. In occupations involving drilling, tunneling and sandblasting operations acute silicosis can be correlated with this unique surface reactivity of silica. The formation or reactive species was demonstrated, using electron spin resonance (ESR) spectroscopy (Dalal et al., 1986; Fuibini et al., 1987; Hochstrasser and Antononi, 1972). Grinding of quartz crystals under ultra high vacuum (10-10 torr) leads to the formation of Si- and SiO• radicals and these radicals are quenched by exposure to air and other gases (Hochstrasser and Antonini, 1972). ESR signals have also been reported from micronized quartz samples that were evacuated at 413 K (Bolls et al., 1983). In order to find a more direct relationship of such radicals to acute silicosis, we made ESR measurements on quartz dusts freshly ground in ambient air and found- that indeed grinding under ambient environment leads to the formation of the Si• and SiO• type of radicals which decay on storing the dusts in air or in biological buffers (Dalai et al., 1986; Vallyathan et al., 1988). The Si• and SiO radical formation on grinding has also been reported by Fubini et al. (1987). In addition, we recently found that •OH radicals are generated in aqueous suspensions of freshly ground quartz (Dalai et al., 1988; Shi et al., 1988; Vallyathan et al., 1988). We have subsequently carried out detailed cytotoxicity and biological assays on freshly made as well as aged quartz dusts. As summarized below, the results provide new insight into the biochemical mechanism of acute silicosis."

Jan 1, 1988

By Howard E. Parkinson

A brief description is given of various Bureau of Mines research activities that have begun since July 1974 and are not being reported on by others at the Third West Virginia University (WVU) Conference on Coal Mine Electrotechnology. An essential feature of the various projects is that they are pragmatic. The projects are applied research and are carried out both by the Bureau in-house research group and by other research groups through contract research. Projects have been directed toward wired-type communications with a special effort to modify the wired systems so as to be more effectively used. The projects are in three groups: Pager phone systems, trolley line phone systems, and guided-wire wireless communications. Also, a brief sketch is given of research that is essential for further developments in mine communications. From the early results of these various projects, the Bureau has good reason to project that there will be improved performance of existing communication systems and that communications will be extended to other individuals working in areas that are excluded from present mine communication systems.

By C. R. Hopkins

"The petroleum refiners of the United States made rapid strides in fuel economy in 1928, when the calculated number of B. t. u. required to refine a barrel of crude petroleum was 637,000 as compared with 698,000 in 1927, a decline of 9 per cent. The major portion of this indicated increase in fuel efficiency was undoubtedly due to the gain in use of the pipe-still and the continuous process of refining as contrasted with the old batch method of distillation.,Almost without exception the new refineries are equipped with one or more pipe-stills, and many of the older plants are changing over to this type of equipment. The refineries of the Appalachian area are among the oldest and most conservative of the country, yet a number of them dismantled their old shell and cheese-box stills and installed pipe-stills in 1928.The more extensive use of the pipe-still was not the only way in which the refiners lowered their fuel requirements in 1928. The use of heat-exchangers, in which the heat from hot vapors to be condensed is used to heat the incoming cold oil, also increased in 1928, and in addition the refiners have kept abreast of the times in saving fuel through better insulation and improved burners.For the year 1928 the refiners burned as fuel the following: 46,400,000 barrels of-fuel oil; 3.362,000 short tons of coal; 114,950,000,000 cubic feet of natural gas; 77,313, 000,000 cubic feet of refinery or still gases; and 470,000 short tons of coke, in addition to a little electricity. This fuel was calculated to have produced a grand total of 582,156 billions of B. t. u., as compared with 578,784 billions B. t. u. in 1927.The total of 46,400,000 barrels of fuel oil burned represents an increase over 1927 of about 5,000,000 barrels, which made it about equal to the 1926 figure. Practically all of the refinery districts used more oil as fuel in 1928. The most important increase - over 2,000,000 barrels - occurred in the East Coast district, where greatly expanded throughput of foreign crude was instrumental in increasing fuel-oil production.The use of coal for fuel at refineries again registered a material decline, the total for 1928 of 3,362,000 short tons being 33 per cent below that of the previous year. The outstanding decrease in the use of coal in 1928 occurred in the East Coast district, where coal was probably replaced by oil. The use of coal for fuel at refineries in the States of Ohio, Pennsylvania, and West Virginia declined materially in 1928; the substitute used in the majority of cases was oil burned in pipe-stills."

Nov 1, 1929

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

To develop and design a bit that will rapidly drill smooth and precise instrumentation holes in soft rock. Approach Use a one-piece bit made by combining a drag bit and a diamond bit. Because a smooth-walled borehole with a precise diameter is needed for borehole pressure cells (BPC) and other borehole instruments, a diamond bit is usually used. However, diamond bit drilling is slow, and the bit will tend to bind when squeezing ground is encountered. On the other hand, the drag bit will cut faster, but the walls of the drill hole will be rough and the diameter will not be as precise. The combination will provide a bit which penetrates as rapidly as a drag bit, but retains the smooth-wall and precise borehole diameter of a diamond bit. How It Works A three-foot-length of EW-size drill rod is centered in a diamond bit by welding it to three equally-positioned spacers at each end of the bit. A drag bit is attached to the EW rod with a standard EW-to-drag bit adapter as shown in the diagram. Three equally-spaced diamond inserts are set to the desired hole size and welded to the diamond bit barrel behind the crown. These inserts increase the smoothness and precision of the hole by cut-ting away any hole closure. Three equally-spaced shims are set approximately 0.020-inch under the overall insert diameter size and welded to the rear of the diamond bit barrel. The combination bit should be used on a diamond drill with either water, mist or air as the coolant.

Jan 1, 1982

By W. F. Marshall

The Bureau of Mines conducted a series of experiments to determine the influence of exhaust rebreathing on emissions from various gasoline and diesel engines. Tests were conducted that simulated operation of engines in nonventilated spaces as well as in spaces with partially restricted ventilation. Results of these tests showed that exhaust rebreathing can have a marked effect on exhaust emissions and thus on the composition of the air in the working space. For the case of restricted ventilation, unacceptably high (greater than 50 ppm) levels of CO in the air of the working space resulted from exhaust rebreathing rates as low as 8 pct exhaust in the engine's intake. Operation in a nonventilated space resulted in highly critical CO levels (fatal in a few minutes) at times corresponding to 1 to 3 pounds of fuel consumed per 1,000 cu ft of space. Tests involving spaces of various sizes showed that volume of the air space [per se] is not important--the primary variable is fuel consumed per unit volume of air space.

Jan 1, 1973

By Robert Blickensderfer

Equipment and procedure for the continuous roll bonding of metal strips are described. The reels, mill rolls, and furnace were located within a vacuum chamber capable of operation at a residual gas pressure of 1 x 10-4 to 1 x 10-5 torr. Several metals were successfully clad at rolling temperatures of 930° to 1,050° C in lengths up to 120 ft. The bimetals that were clad included stainless steel to carbon steel, molybdenum and nickel to stainless steel and carbon steel, and titanium to carbon steel. Bend tests of bond integrity are described, and microstructures of the interfaces are presented. The amounts of brittle intermetallic phases formed at the interface are minimized by this cladding method.

Jan 1, 1980

By Robert F. Holub

The Bureau of Mines has made a study of the magnitude of the variations of radon daughter mixtures, with the objective of determining whether these variations reflect the existing physical conditions in uranium mine atmospheres or if they are merely random or systematic errors. To accomplish this, many data have been plotted using a triangular graphing technique which shows that plateout affects RaA more than RaB or RaC, and that it is impossible to find simple correlations between working level ratios, radon daughter mixtures, and age.

Jan 1, 1978

By Roberta L. Hudak, Ellsworth R. Spencer, Eric R. Bauer, Adam K. Smith

The National Institute for Occupational Safety and Health (NIOSH) is conducting research with the objective of preventing hearing loss in the mining industry. Longwall mining is one sector that has received considerable attention. Studies involving the monitoring of worker noise exposures, characterizing equipment sound levels and dominant noise sources, evaluating engineering noise controls, analyzing hearing protection device (HPD) effectiveness, and testing of improved sound level monitoring techniques specifically for longwall mining systems, are being conducted. The research efforts revealed that stageloader operators are the most exposed longwall workers, with the discharge end being the noisiest location along the stageloader. In addition, the studies have shown that using stationary dosimeters, coupled with observational data of the cutting cycle and worker habits, has the potential for improved monitoring of the effectiveness of engineering noise controls. To address the ineffective use of soft foam earplugs, a simplified 3-step method was developed for inserting soft foam earplugs. Results indicate a 9 dB greater attenuation after training subjects on the 3-step method. Finally, muff type HPDs are being evaluated for effects of speech intelligibility in noise. The combined results of these studies illustrates that much can and has been done to prevent noise-induced hearing loss (NIHL) in the mining industry, especially with respect to longwall mining workers. This paper presents an overview of ongoing studies, a progress report of results, and the implications for reducing worker noise exposures and preventing NIHL in longwall mining workers.

By F. C. Turin, K. M. Cornelius

1. INTRODUCTION Underground mining in the USA has undergone significant change in the past 20 years. Two key elements have been increased mechanization and a more educated work force in spite of these changes, many jobs continue to be labor-intensive and repetitive in nature. They entail tasks that, performed over time, can take a toll on the soft tissues and joints. The problem may be compounded by an aging mining workforce. In 1996 the mean age of the coal mining work force was 45 years and the median total years of experience was 20 (NMA 1998). As a person ages, the body resilience to chronic wear and. tear is reduced, which may cause a worker to pay an increasingly higher health price for performing the same task. Mining companies, like many others, are becoming more aware of cumulative effects to the worker as reports of these types of injuries rise. . Conducting a job analysis is an important step when considering a job redesign or modification to reduce worker cumulative trauma exposure. A basic approach to job analysis is to examine the types of aches and pains reported, the tasks performed, and work site conditions. The US Bureau of Mines (USBM) conducted an evaluation of roof-bolting tasks performed at an underground coal mine concerned about early warning signs of cumulative trauma. This evaluation will comprise the primary focus of this chapter. The approach used for the roof-bolting race study may be applicable to other work environments. 2. FUNDAMENTALS OF CUMULATIVE TRAUMA EXPOSURE Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders that affect the nerves, tendons and muscles. Common examples include lower back pain, tendinitis and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may not appear immediately, but can take weeks, months or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute there to a single event. In fact, it is more common to identify factors that may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTD) have been commonly used to refer to disorders that have occurred due to work-related activities. Three main risk factors contribute to CTD: force, repetition and awkward postures. Any one or combination of these may contribute to the development of CTD. Therefore, the design of equipment in conjunction with the required tasks should be evaluated when attempting to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list (Putz-Anderson 1988), describes ergonomics concerns that, overall, should be minimized at the work area: • Crowding or cramping the worker: a work area layout may unnecessarily constrain movements of the worker. • Twisting or turning: placement of tools and materials may require the worker to twist the spine to fulfill the requirements of the job. • Repeated reaching motions: the layout of the work area may require the worker to lean to reach and grasp the necessary tools and controls. • Misalignment of body parts: the arrangement of the work area may require the worker to frequently have one shoulder higher than the other or have the neck or spine bent to one side. While many of these concerns are a function of equipment design and environmental conditions, making workers aware of these issues may help them to adapt their work habits to reduce risk of injury. Additionally, this information is useful when conducting an ergonomic evaluation of a work area and associated tasks. 3. UNDERGROUND MINING ENVIRONMENT The underground mining environment is a unique challenge. It is more difficult to develop controls for an underground mine site as compared with a factory setting where equipment and facilities can be more easily designed to reduce worker force, posture and repetitive exposures. In an underground mine, workers are required to perform labor-intensive tasks that often cannot be avoided due to environment constraints. The dynamic nature of the environment does not allow easy implementation of mechanical assists to reduce force exposure. Many of the tasks performed by workers are repetitive. Restrictive work areas due to low ceiling height, low lighting levels and large pieces of equipment cause workers to perform these tasks in postures that are not desirable. Designers of underground mining equipment can control how a machine will function, but not the environment in which it will be used, Hazards in an underground mine cannot be completely removed by redesigning the system. There are many hazards and information sources that must be continually monitored by workers including their position in relation to large pieces of mobile equipment and unpredictable geological anomalies. Thus, immediate dangers may take priority over awareness of ergonomic considerations while performing a job. 4. CASE STUDY OF UNDERGROUND ROOF BOLTING 4.1. Roof Bolting and Cumulative Trauma Exposure In an underground coalmine, after an area is mined it is necessary to support the roof to keep it from collapsing. Since 1950, the primary method for supporting the mine roof has been installation of roof bolts. Long bolts installed into the roof compress the layers of strata achieving a uniformly distributed support anchorage. Roof bolts, typically 6-8 feet long, are installed by workers using large roof-bolting machines. There are different types of machines

By S. B. Flagg, J. F. Barkley

In the past few years an awakened activity in power-plant econ- omies has resulted in a marked improvement in the equipment for generating and utilizing steam. Although the improvement in design and construction of steam-driven prime movers has been greater than that of the steam-generating equipment, the economies obtained with the more efficient engines and turbines have stimulated interest and activity in eliminating unnecessary boiler and furnace losses. Much attention has been given to the boiler room in efforts to obtain proper combustion of the coal, because of the importance of the coal item in costs of power production. As evidence of this increasing interest may be cited the record of the development within the past few years of new apparatus for the analysis of flue gases. Many new forms of apparatus have appeared, including those for the determination of carbon dioxide, oxygen, and carbon monoxide, and others for indicating and for recording the content of carbon dioxide only, as carbon dioxide content is usually a good indicator for the control of furnace operation. Because of the large number of steam-power plants operated by the Federal Government and the number of CO, recorders used therein the Bureau of Mines undertook to collect information regard- ing the practical application of such recorders. Articles published from time to time concerning CO, recorders have been mostly descrip- tive, giving little reliable information as to the results that could be expected from the various types of instruments in ordinary prac- tice, and most of the tests made have been of a laboratory nature. Tests of several different types of recorders were made under service and laboratory conditions in order to obtain needed information. The purpose of the Bureau of Mines in publishing the results is to show the factors which may affect the accuracy of a CO, recorder and the manner in which a recorder should be tested. Readers should note that the remarks on different recorders apply to the instruments tested and not to later instruments of the same makers. In the course of the tests the following details were determined: 1. The lag in recording changes of composition of a flowing gas. 2. The accuracy of each type of recorder.

Jan 1, 1916