Search Documents

By Gerrit V. R. Goodman, Charles D. Taylor, Edward D. Thimons

Future coal mining systems will be able to cut from crosscut to crosscut where advances could exceed 100 ft. However, limitations arise when ventilating such mining systems. In deep advance mining, there would be no workers at the face to advance ventilation tubing or curtain manually. Traditional methods also provide no means for maintaining face ventilation after the miner backs away from the face. U.S. Bureau of Mines research is studying means to provide effective ventilation at cut depths beyond the current limit of 40 ft. Several innovative ventilation schemes are currently being considered. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Jet fan testing in a 90-ft entry revealed that higher exit velocities and greater penetration depth occurred when various configurations were used to confine and direct the air flow. Additional testing also indicated that 2,200 cfm of fresh air was delivered to the face 90 ft distant when a check curtain was used to limit entrainment around the fan. Without this curtain, this quantity dropped to only 1,000 cfm This testing indicated that a jet fan was capable of providing ventilation to a distant face area. It also highlighted potential problems, such as recirculation at the fan and reentrainment in the jet flow. Despite these potential problems, jet fans may be adequate for ventilating cuts exceeding 40 ft.

Jan 1, 1992

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

By Parviz F. Rad

The Bureau of Mines conducted groove cutting experiments in marble, lime-stone, granite, and quartzite with a 7-inch disk cutter under a normal thrust of 7,000 lb. The values of muck weight per unit length, specific energy, cutting coefficient, and groove depth for each of these rocks were determined for groove spacings ranging from 0.1 to 4 inches, and from these results the values of optimum and critical spacing were computed" The results indicate that compressive strength may be used to predict some of the cutting characteristics of the independent grooves. Considering all the cutting characteristics, particularly those for the interacting grooves, Shore hardness, coefficient of rock strength, and torsional velocity correlate with cutting characteristics better than do other physical properties. Some of the field applications of the principles established in this report are identified.

Jan 1, 1974

By Fred N. Kissell

Experimental work by the Bureau of Mines indicates that when a coalbed is degassed by boreholes, the flow of methane may actually increase with time. This phenomenon appears to be the result of a relative-permeability effect; that is, the coalbed permeability to the gas increases sharply with decreasing water saturation. This report reviews the background of experimental evidence indicating a relative-permeability effect, and presents the results of a computer simulation of two-phase flow in coal.

Jan 1, 1975

By Kris Chatrathi, John E. Going, Kenneth L. Cashdollar

Two types of flammability limits have been measured for various dusts in the Fike 1-m3 (1000-L) chamber and in the Pittsburgh Research Laboratory (PRL) 20-L chamber. The first limit is the minimum explosible concentration (MEC), which was measured at several ignition energies. In addition to the three dusts studied previously (bituminous coal, anthracite coal, and gilsonite), this work continues the effort by adding three additional dusts: RoRo93, lycopodium, and iron powder. These materials were chosen to extend the testing to non-coal materials as well as to a metallic dust. The new MEC data corroborate the previous observations that very strong ignitors can overdrive the ignition in the smaller 20-L chamber. Recommendations are given in regard to appropriate ignition energies to be used in the two chambers. The study also considered the other limiting component, oxygen. Limiting oxygen concentration (LOC) testing was performed in the same 20-L and 1-m3 vessels for gilsonite, bituminous coal, RoRo93, and aluminum dusts. The objective was to establish the protocol for testing at different volumes. A limited investigation was made into overdriving in the 20-L vessel. The LOC results tended to show slightly lower results for the smaller test volume. The results indicated that overdriving could occur and that ignition energies of 2.5 kJ in the 20-L vessel would yield comparable results to those in the 1- m3 vessel using 10.0 kJ. The studies also illustrate the importance of dust concentration on LOC determinations.

By John P. Conway

This Bureau of Mines investigation was undertaken to determine the feasibility of lock-bolt support in Tertiary-gravel material. Pull tests were performed on five types of rock-bolt anchors to determine their optimum anchorage capacity. Four of these anchors are commercially available; the fifth, an explosive-anchor bolt, was developed by the Bureau of Mines. To increase anchorage capacity, epoxy grout was used with several of the commercial types of bolt. Tests showed that sufficient anchorage could be obtained by employing epoxy-resin grout with the commercially available wedge bolt, or by using the explosive-anchor bolt. Also estimated are bolt spacing and cost of a rock-bolt support system.

Jan 1, 1971

By Mridul Gautam, Alex Bugarski

Size Distribution and Deposition in Human Respiratory Tract: Particle Mass and Number Aleksandar Bugarski and Mridul Gautam National Research Center for Alternative Transportation Fuels, Engines and Emissions Department of Mechanical and Aerospace Engineering West Virginia University TOXICITY OF ULTRAFINES (MAUDERLY et al.) ? FINER PARTICLES PENETRATE MORE READILY INTO CELLS AND TIXROUGH TISSUE BARRIERS ? FINER PARTICLES HAVE GREATER SURFACE AREA PER UNIT MASS, AND A LARGE NUMBER OF TOXIC REACTIONS OCCUR AT THE SURFACE ? FINER PARTICLES DISSOLVE MORE READILY THAN LARGER PARTICLES THUS ENHANCING THE BIO- AVAILABILITY OF SOLUBILIZED COMPOUNDS EPIDEMIOLOGICAL STUDIES INDICATE THAT THE IMPORTANCE OF ULTRAFINES REMAINS SPECULATIVE

By C. P. Lazzara, Y. Miron, A. C. Smith

This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, utilizing the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2)

Jan 1, 1992

By Peter F. Strong, Robert L. Lagace, Alfred G. Exslie

The theoretical study of WF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer is the concern of this paper. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. The theoretical results are compared with published measurements. This work was part of an investigation of new ways to reach and extend two-way communications to the key individuals who are highly mobile within the sections and haulageways of coal mines.

Nov 14, 1974

By A. B. Hooker

Since man first mined underground, there has been need for adequate illumination; this need has never been fully supplied. At first, suitable lamps were not available. Gradually they have been developed, but along with that development the need for better and better lamps has continued owing to the following conditions and factors: 1. Increasing hazards from gas and dust ignitions. 2. The speeding of operations with mechanized mining, which necessitates greater visibility. 3. A demand that cleaner coal be loaded, which requires higher levels of illumination. 4. The cost of compensation for injuries that has created a demand for better illumination and safer lamps. Use of better lamps has been retarded by: 1. Prejudice and resistance to change on the part of the workers in some districts. 2. The cost and upkeep of the lamps. 3. The present types of lamps, while a great improvement over the old lamps, do not entirely fulfill the requirements for a safe and efficient light for underground workers.

Jan 1, 1938

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method, Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out- crop will emit low levels of methane gas.

Jan 1, 1977

By Tye J. Lasich

This project involved modeling rock masses with varying Rock Mass Rating (RMR) values to determine the degree of instability that develops around an underground opening as a function of RMR. The modeling was performed using Itasca?s UDEC distinct element software, which allows explicit modeling of blocks of rock and how they interact with each other. The analyses included three different orientations of the joint sets, four different joint spacings and three different values of joint strength, which combine for a total of 36 different combinations of model parameters. Two different modes of behavior were observed: local failure of area immediately surrounding the roof and sides of the opening, and deep-seated failure extending a large distance beyond the opening. Quantification of the size of the unstable area that developed provides numerical validation of empirical guidelines used in design of ground support and instrumented monitoring systems.

Jan 1, 2005

By A. F. Colombo

Infrared spectroscopy employing attenuated total reflectance (ATR) techniques on thin films of dried gelatinized starch solution was used during Bureau of Mines research to determine the structural and impurity differences in starch products and to correlate these characteristics with the flotation response of a nonmagnetic taconite. All of the starch products evaluated gave spectrograms which were characteristic of the anhydroglucose monomer and its polymerization product. Distinct infrared absorption peaks caused by the protein molecule were observed and were used to classify the starches. Correlation of laboratory flotation of calcium-activated gangue from a Mesabi Range nonmagnetic taconite and infrared spectra produced from gelatinized starches showed that protein impurities and linear chain structure limited the effectiveness of starches as iron mineral depressants. Starch products having spectrograms similar to pure amylopectin were generally good depressants for iron oxides, were effective at about one-half the addition that was required for starches that gave infrared responses similar to pure amylose, and yielded acceptable iron concentrates containing 61.5 percent iron and 6.5 percent silica.

Jan 1, 1969

By Peter F. Strong, Robert L. Lagace, Alfred G. Emslie

This paper is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1973

By W. H. Lewis

This Bureau of Mines report and its companion report (Information Circular 9074) have been prepared as a complete reference on underground coal mine lighting. This report discusses the fundamentals of light and its interrelationship with the visual process. The purpose of the report is to insure an understanding of the numerous complex and interrelated factors that must be considered to design and implement a mine lighting system that will satisfy human needs for good vision and comfort. Topics include history, objectives, and technical considerations of coal mine lighting; light physics; light and vision relationships; and disability and discomfort glare.

Jan 1, 1986

By L. C. Headley

Surface areas of two synthetic and three natural consolidated porous samples were obtained by the Orr low-pressure permeametry technique. The results suggest that the Orr technique is a useful substitute for the low-temperature gas adsorption (BET) method for determining the surface area of rock samples. It was more rapid than the BET method, and the surface-area values obtained were larger but agreed better with BET values than values calculated from the Kozeny-Carman equation. Efforts were unsuccessful to demonstrate the influence of channel-size distribution on pressure-flow rate curves by means of experimental data and a parallel channel model.

Jan 1, 1971

By Clarence Hall, Spencer P. Howell

This bulletin deals with the characteristic features of the principal explosives used in mining and engineering operations, and espe- cially with the tests that show the suitability of different classes of explosives for different kinds of work. The Bureau of Mines pub- lishes the report as one of a series dealing with tests of explosives and methods of reducing the risks involved in the use of explosives in mining operations. The application of explosives to engineering and mining opera- tions has increased rapidly in recent years. According to a pre- liminary report issued by the Bureau of the Census, 469,000,000 pounds of explosives was manufactured in this country during the year 1909, and the greater part of this production was used for industrial purposes. In large engineering projects and in mining operations requiring the use of explosives the selection of a suitable explosive from the many varieties offered for sale is of fundamental importance. Vari- ous considerations are involved in the selection of an explosive of proper class for the blasting to be done. Many explosives suitable for quarry work are unsuitable for use in deep mines or in close workings. In metal mining and in driving tunnels the character of the gases evolved by the explosive on detonation is an important consideration. An explosive for use in gaseous or dusty coal mines must be formulated and compounded so that its flame temperature and the height and duration of its flame are reduced enough to per- mit its being used with comparative safety. In wet workings or in submarine blasting explosives impervious to moisture are requisite. In extremely cold climates explosives that do not require thawing are desirable, provided they are equally good in other respects. An essential requirement of all explosives, especially of those for use in tropical countries, is that they shall remain stable without change in chemical or physical characteristics.

Jan 1, 1913

By Forrest T. Moyer

THE SAFETY record of the mineral and mineral-fuel-mining-and-processing industries retrogressed slightly in 1964, as indicated by the 3-percent increase in the frequency rate of all injuries. A slight improvement in the fatality rate was more than offset by the less-favorable rate of occurrence of nonfatal injuries. The overall-operating activity of these industries was lower in 1964 as measured by slight declines in employment and total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 18.00 per million man-hours. This overall rate in 1964 comprised frequencies of 0.29 for fatal injuries and 17.71 for nonfatal work disabilities, which compared with respective rates of 0.30 and 17.20 in 1963. Fatalities totaled 538 or 30 less than in 1963. However, the total nonfatal disabilities of 33,151 in 1964 was 492 higher than in the preceding year.

Jan 1, 1965

By D. Harrington, C. W. Owings

Each year at least one and in some years several explosions are reported as having resulted from firing of mudcapped shots in coal mines; undoubtedly a number of small or local explosions occur that are not reported; in addition there are numerous accidents, some of them fatal, attributable to this reprehensible blasting practice. It is surprising that so few explosions and other accidents from this cause occur since the practice of firing mudcapped, Even in gassy "adobe," "dobe," "sand blast," or "bulldozed" shots is widespread. mines where general blasting is safeguarded by being done with permissible explo- sives, rocks or bowlders frequently are blasted with mudcapped shots of dynamite; even if permissible explosives are used, this type of shooting is dangerous. The usual method of preparing a mudcapped shot is to place the explosive, either in loose or cartridge form, with the detonator or "cap" on top of a piece of rock or coal and cover it with several handfuls of moist clay, loam, sand, or When the shot is road dust; in many cases there is no covering of any kind. fired a dense cloud of dust, together with an intensively hot fleme, are thrown into suspension, and if the dust is explosive or ignitable an explosion or igni- tion is likely to result practically simultaneously. The presence of gas greatly increases the explosibility of the dust, as well as the probability of an ignition. Every shot, of any known explosive, fired in a coal mine without having the charge properly confined in a drill hole and tamped with incombustible stemming to the collar of the hole, is capable of initiating an explosion that may cause the death of every man in the mine. Attention has recently been directed to this unsafe practice by an explo- sion resulting from a flagrant disregard of safe blasting practices in one of our The mine had been idle for several years most productive coal-mining regions. and was being prepared for reopening on a different system of mining. Six to 10 inches of bottom coal had been left in place during former mining operations, but in the new system it was felt desirable to remove the bottom coal left in certain parts of the mine. Instead of drilling holes in the coal, loading them, and fir- ing in the usual safe manner, five or six charges of dynamite were placed on top of the coal in each of several rooms; and while the men were at the mouth of the

Aug 1, 1929

By Chelesa C. Woodward, Gregory G. Miller, Walter K. Utt, Wayne L. Howie

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the use of a drill monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof so that roof drill operators can be warned when a weak layer is being drilled. Measurements taken during drilling can be converted to suitably scaled features so that a neural network can classify mine roof strata in terms of relative strength. The feasibility of this concept has been demonstrated in the laboratory. The research project was undertaken in order to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills used in underground mining and would likely find wider application as well.

Jan 1, 2002