Search Documents

By D. Z. Hobbs

Because an economic method for preparing pure boron has not been developed, a program was started by the Bureau of Mines to evaluate existing techniques or to develop new methods for preparing the pure element. This report describes investigations directed toward the development of techniques for the preparation of pure boron by fused-salt electrolysis. Only two of the several fused-salt baths tested were satisfactory for the preparation of boron. These baths contained (1) potassium fluoride, lithium fluoride, potassium fluoborate and boron trioxide; and (2) potassium fluoride, potassium chloride, and boron trioxide. Of these two mixtures, the latter was more satisfactory. Elemental boron of from 90- to 95-percent purity and, in isolated cases, as high as 98-percent purity, was prepared from these two types of fused-salt baths. There appeared to be no distinct differences either in the yields or the purity of boron prepared at current densities ranging from 795 to 1,000 amperes per square foot. Current efficiencies were as high as 85 percent.

Jan 1, 1961

By I. L. Nichols

Laboratory characterization studies have investigated the processing variability of carbonaceous uranium-bearing materials found in-sandstone deposits. This work was conducted by the Federal Bureau of Mines in support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs. Conventional processing produces only partial uranium recovery from these ore materials. Ore samples from New Mexico, Texas, and Wyoming were examined, and each responded differently. Using direct acid leaching techniques, some of the ores required acid additions of only 50 pounds per ton, while others required 300 pounds per ton of material. Maximum extractions ranged from 83 to 94 percent in the six ores tested. Roasting those ores prior to leaching improved extraction of the uranium to the 90 to 99 percent range. An oxidative autoclave treatment used with five of these ores resulted in extraction of 78 to 97 percent of the uranium. The experimental studies also showed that some carbonaceous materials can be concentrated by froth flotation. The flotation tailings were amenable to acid leaching, and up to 98 percent of the uranium was extracted from this type of material.

Jan 1, 1979

By W. L. Hunter

Eleven steelmaking heats are described in this Bureau of Mines report in which acid practice was used to produce carbon steel from pre reduced iron ore pellets. Furnace slags obtained with no flux addition to the charge became quite viscous as they cooled, which precluded pressure casting from a ladle. Lime was added to the furnace charge at two levels to eight of the heats to modify slag characteristics in the furnace, and to the ladle in two heats to further modify the ladle slag cover. Selected ingots from nine heats were successfully rolled on a commercial mill to produce No. 10 reinforcing bar.

Jan 1, 1974

By B. G. White

NIOSH researchers have identified a pattern of fracture zone development that suggests an explanation for fracture formation around rectangular openings in underground mines. This pattern is characterized by shearing and dilation that result in either faults or in the repeated formation and propagation of en echelon fractures from sites of tension. Two computer modeling codes, Fast Lagrangian Analysis of Continua (FLAC) and Particle Flow Code (PFC), were used to model different aspects of this pattern. Use of very small elements with FLAC enabled the identification of sites of initial tension near the skin of square-cornered rectangular openings, while PFC allowed the initiation and progressive development of fractures from these sites to be followed as the fractures evolved. Such studies can lead to a greater understanding of how roof support can be better selected and installed for specific conditions in underground mines prone to roof falls and rock bursts. These studies may also lead to modifications of corner and opening shapes that could be incorporated into mine designs to produce more stable mine openings and reduce the risks of rock falls and rock bursts.

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals. Also, miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupational Research Agenda, problems created by occupational hearing loss include (1) the reduced quality of life due to social isolation and unrelenting tinnitus, (2) impaired communication with family members, the public, and coworkers,(3) a diminished ability to monitor the work environment (e.g., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers? compensation and hearing aids.

Jan 1, 2000

By Terry J. Close

In 1992, as part of the U.S. Bureau of Mines Idaho Land Assessment Program, the Western Field Operations Center investigated the mineral resources of the 30,300-hectare Elk Summit study area. The area is in the Clearwater National Forest, adjoining the Selway-Bitterroot Wilderness in Idaho County. Idaho. The study area is underlain by granitic and metasedimentary rocks. Associated with these rocks are road metal (stone) resources, black sand mineral placer resources, and thermal water resources. Also present are abundant sand and gravel. Two of the five sites examined during the Bureau study have road metal (stone) resources, one has black sand mineral resources, one has thermal water resources. The fifth site is a black sand mineral placer occurrence. There is no evidence of petroleum or coal resources. Idaho County records indicate that 38 mining claims, mostly black-sand placer, have been located in the study area, Twenty-three of the claims are current. Workings consist of a few pits and trenches at the placer, and two borrow pits. The only mineral commodity produced from the area was about 1,500 tonnes of stone excavated from the Savage Pass and Swamp Creek borrow pits along the Elk Summit road, north of Hoodoo Lake. The stone was used to surface the road; these stone resources will continue to be used as needed.

Jan 1, 1993

By Fred Leighton

The least squares method of rock noise source location presented is shown to be more accurate and reliable than standard direct solution methods. This method is particularly effective in improving solutions from rock noise locations outside of geophone array boundaries. A least squares solution for a medium .in which the seismic velocity is the same in all directions is also presented. In this special case, one can solve for both the source coordinates and the velocity.

Jan 1, 1972

By Launa Mallett, Charles Vaught, Michael J. Bmick

Since 1991 the Pittsburgh Research Center (PRC formerly part of the U. S. Bureau of Mines) has been tapping u valuable resource-researchers have recorded extensive interviews will, 30 individuals who are recognized as experts in the area of mine emergency response. These veterans related stories and observations from events experienced during as many as 47 years of response activities. Overall, the response veterans averaged 29 years of mine emergency response experience and 35 years mining experience. Individuals [ ] interviewed included representatives from mining companies, the UMWA and state and federal government agencies. This information was gathered so dial it could he provided to today's miners and to tomorrow's emergency response personnel. It is hoped the collective wisdom that has been obtained can be used to help train new responders and guide those decisions which mill have to be made on the scenes of future events. During interviews file emergency response experts were asked to discuss lessons they had learned through experience. The interviewers asked them to tell what they had learned that would cause them to handle similar situations differently and to tell about things they saw at past events shat the would warn others not to do in the future. In response the experts discussed a variety of things. Most of their responses, however, touched on some of the same topics including: preparedness, experience people on-site mine rescue teams, and decision making. A summary of their responses provides alt overview of [lie lessons learned on-site at tile largest mine disasters in the country.

By A. F. Jolly

As a part of ongoing research into the sulfidation partitioning of selected complex minerals, the U.S. Bureau of Mines conducted research designed to selectively recover Cu from sulfidized chalcopyrite (CuFeS2). Ferric chloride (FeCI3) solutions leached >90 pct of the Cu and <20 pct (sometimes < 10 pct) of the Fe in the sulfidized concentrates. Cupric chloride (CuCI2) leaches were even more selective, solubilizing essentially 100 pct of the Cu and < 5 pct of the Fe. In contrast, leaching non-sulfidized CuFeS2 with either FeCl3 or CuCl2 showed that somewhat more Fe than Cu dissolved. These studies demonstrate that Cu is substantially more leachable from sulfidized CuFeS2 than from nonsulfidized CuFeS2? The Cu-and Fe-bearing constituents generated as sulfidation products, CuS (covellite) and FeS2 (pyrite), respectively, are differentially dissolved. The solubility of Fe from pyrite in sulfidized CuFeS2 is much lower than the solubility of Fe from complex nonsulfidized sulfide where Fe and Cu are bound in the same crystal lattice. Thus, the Cu dissolves selectively, producing a high-Cu filtrate from which Cu can be recovered by cementation or by electrolysis. Flotation of CuS-FeS2 mixtures indicates partitioned phases can be physically separated if effective liberation can be achieved. Magnetic separation tests yielded less promising results.

Jan 1, 1991

By R. O. Dannenberg

Applicability of the fluosilicate sintering process to recovering beryllium from beryl-spodumene concentrate analyzing 1.4 to 3.7 percent BeO (10 to 30 percent beryl) was investigated. The work was one phase of a Bureau of Mines research program undertaken to assess applicability of conventional processes and to devise new procedures for treating various potential beryllium feed materials. Beryllium recovery of about 70 percent in a product of 99-percent BeO grade was achieved in treating 3D-percent beryl concentrate. The process consisted of (1) sintering a briquetted charge of concentrate, soda ash, and sodium fluosilicate for 3 hours at 750° C.; (2) extracting the soluble beryllium by multiple stages of water leaching; (3) adding caustic to the leach solution and boiling to hydrolyze and precipitate crude beryllium hydroxide; (4) dissolving the crude beryllium hydroxide in sulfuric acid and separating the solution from undissolved silica; (5) sulfidizing the acid beryllium solution to precipitate heavy metal impurities; (6) adding ammonia to the clarified sulfate solution to precipitate beryllium hydroxide; and (7) converting the hydroxide to beryllium oxide (beryllia) by calcining at 900° C. About 60 percent more sodium fluoSilicate was required per unit of beryl than is used industrially in treating 10-to 12-percent BeO concentrate (80 to 90 percent beryl). Recovery decreased, and flux requirements increased, when treating concentrates containing less beryl.

Jan 1, 1963

By R. E. Morgan, J. F. Barkley

"INTRODUCTION In city smoke-abatement work it is customary to require approval of the sizing of fuel-burning equipment. This is to insure that, with reasonable attention, the equipment can be operated essentially smokelessly, having such features as ample furnace volume and air supply. To answer the many inquiries that come to the Bureau of Mines as to what dimensions are acceptable and standard, the requirements of a number of smoke-abatement ordinances have been tabulated.CONCLUSIONSStudy of these tabulations shows that even after many years of fuel-burning practice and experience there is no common standard. Variations in the requirements for the same type of equipment under the same conditions of operation are great. This causes considerable difference in installation costs. Over-all costs being affected, the competitive positions of different types of fuel-burning equipment are also affected. It is apparent that there is a lack of information as to proper dimensions that is commonly accepted as authoritative.DISCUSSIONTable 1 gives the minimum furnace-setting heights required by various cities for mechanical underfeed stokers installed under H.R.T. boilers. Figure 1 shows a typical installation. The dimension given for each case is the distance from the dead plate of the stoker to bottom of boiler shell, unless otherwise noted. As shown in the table, different cities use different size-classification systems; it is not possible to make complete, exact, direct comparisons. Table la gives a comparison for various cities, showing the approximate percentage difference in H.R.T. furnace-setting heights required from those recommended by the Stoker Manufacturers' Association arbitrarily chosen to serve as a basis of comparison. The percentages are approxi¬mate because they were calculated as if all heights as given were measured from the dead plate of the stoker. In two cases a lower height is permitted, in a number of cases the height may be the same, and in a number of cases the height must be greater. The percentage increase goes to 100 in one case. Lack of uniformity is quite evident."

Mar 1, 1950

This Volume documents the Phase 111 effort on the Seismic Detection and Location of Isolated Miners on Contract H0122026 undertaken during the fall of 1972 by a task team composed of ADL staff and several seismic consultants. The team was assembled specifically to work together on complementary tasks, at an accelerated level of effort for four months, to meet the Bureau of Mines&apos; time schedule for obtaining independent, objective, technical judgments regarding seismic methods and systems for detecting and locating isolated miners. The impetus for this work resulted from a compilation and analysis, during the first half of 1972, of new experimental data obtained from a series of in-mine field tests conducted by Westinghouse Corp .+ using the CMRSS* interim seismic location system. The Bureau of Mines took advantage of the availability of these new data to reassess the potential and limitations of various seismic methods and systems, and to direct its seismic system improvement program accordingly. ADL assisted the Bureau in this reassessment by drawing on the skills of seismic consultants from industry, universities and government, to supplement the skills of the ADL project team. The consultants were principal resources of broadly-based and detailed technical expertise in the areas of seismic signal-source and signal-propagation characteristics, natural and cultural seismic noise, seismic sensors and field instrumentation, seismic signal and data processing for detection and location, and overall seismic system utilization in the field under operational emergency conditions. Specifically, the participating consultants were: F. Crowley, Air Force Cambridge Research Laboratories ; W. Dean, Teledyne Geotech, Alexandria Laboratories; R. Greenfield, Pennsylvania State University; J. Kuo, Columbia University; D. Peters and R. Crosson, University of Washington; and F. Pilotte, U.S. VELA Seismological Center. The principal ADL participants were J. Ginty, R. Lagace, M. Roetter, and R. Spencer.

Jan 1, 1974

By W. P. Stroud

In this U.S. Bureau of Mines report, the conditions required for the direct reconstruction of a tomogram from observed line integrals are examined. Because of the limited access to the working faces in coal mines, the special case of access to only two opposite faces is emphasized. Classical matrix methods were used for small dimensional (2 by 2, 3 by 3, and 4 by 4) applications to determine the limitations and the requirements for a solution. The results for large (n by n) grids were then inferred and generalized from those of the smaller grids and matrices. Limited access tomography is found to be appropriate for in-seam hazard detection from seismic and microwave data, but it is shown that additional data must be added to obtain a direct solution.

Jan 1, 2010

By Walter J. Frank

Thls report summarizes work done under Bureau of Mines contract H0357100, "Development of a Crimp Connector for Trailing Cable Splices." The purpose of this effort was to establish optimum connector design conditions to meet flex cycle, pullout and electrical resistance criteria on phase power conductors. Field testing of "optimum design" connectors is briefly discussed. One of the primary objectives of contract H0357100 was to enable one to design better performing phase conductor connectors. Illustrating the practical significance of this 1s a discussion on the development of a new splice kit for trailing cables. The connectors in this kit were designed in accordance with the design methods described in the contract final report. Kit components, test data, and a connector installation tool are also discussed. The successful effort on the phase connector has resulted in contract H0377042, entitled "Design and Testing of Joining Sleeves for Trailing Cable Ground and Pilot Wires." The purpose of this contract (currently in effect) is to improve ground-conductor and pilot-wire performance. Significant findings to date are discussed.

Jan 1, 1979

By D. E. Wolfson

The Bureau of Mines carbonized 21 coal samples from Fayette, Greene, and Washington Counties, Pa., at 900° C, using the Bureau of Mines-American Gas Association (BM-AGA) method, and determined yields of products and physical properties of the coke. These samples represented high-volatile A Pittsburgh, Sewickley, Waynesburg, and Upper Freeport and medium-volatile Upper Freeport and Lower Kittanning coals. About 20 percent of all coals presently carbonized in commercial coke ovens in the United States are mined in Greene and Washington Counties, principally from the Pittsburgh seam. Sulfur content of the Pittsburgh coals in these counties is moderately high (1.0 to 3.2 percent) but, because of extremely large reserves, accessibility to eastern United States markets and excellent blending characteristics to yield strong coke, these counties will continue to be an important source of metallurgical coals in the future. Most coals from the other seams contained more than 2 percent sulfur, which would limit their use as metallurgical coals.

Jan 1, 1968

By John A. Breslin

Three scale models of coal mine entries and mining machines were constructed by the Bureau of Mines to study the effects of ventilation parameters on dust concentrations where mining personnel would be working. A one-fifth-scale model of a coal mine entry with a drum-type continuous-mining machine and a one-sixth-scale model of an entry with a twin-borer-type machine were used as well as a one-fifth-scale model of a longwall face with a double-drum shearer. Methane was used as a tracer gas to simulate respirable dust in the models. The distance of the end of the brattice or tubing from the face was found to be more important than the airflow rate for the drum-type machine. Dust reductions greater than 90 pct were shown to be possible with a secondary ventilation system used with the twin borer and a dust collector mounted on the longwall shearer. Cutting-head speed had a significant effect on concentrations at typical positions of miners with the drum-type machine and longwall shearer but not for the twin borer.

Jan 1, 1976

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990

By J. I. Paige

The Bureau of Mines, U.S. Department of the Interior, conducts research on methods to minimize the requirements for mineral raw materials through conservation, substitution, and increased minerals and metals recovery from primary and secondary domestic resources. To further this goal, prior Bureau research had devised a pyrometallurgical technique (RI 8211) to recover metallic iron and copper from molten copper smelting furnace slags by carbothermic reduction. As a continuation of this Bureau research on the carbon injection technique, reverberatory and electric furnace slags were treated in an 800-kva electric arc furnace by simultaneously top feeding the slag and injecting coke breeze into the bottom of the molten bath. Results of the tests show that 76 to 89 pct of the copper and up to 48 pct of the iron contained in the smelting furnace slag were recovered in a metallic phase, while 56 to 82 pct of the carbon injected into the sys-tem was utilized as the reductant. Laboratory evaluation has shown that the metal product, which contains 86.9 to 95.0 wt-pct iron and 1.3 to 4.1 wt-pct copper, will be a satisfactory medium for recovering copper by cementation. The expected energy consumption for the process is 110 kwhr per ton of molten slag treated and 520 kwhr per ton of solid material charged.

Jan 1, 1982

By Ronald S. Conti

Fire is a major concern for those who work in underground mines. A mine fire can occur at anytime and often results in a partial or total evacuation of mine personnel and could result in the loss of lives. Therefore, having a workforce that is well trained to prevent, detect, and fight a fire is important. This paper focuses on responders’ preparedness for fire. Responders in this context are considered the entire workforce and are categorized as first, second, and sustained responders and evacuating miners. Quality training enhances ones awareness of mine fire hazards and promotes self-confidence in combating fires and responding to emergencies. Early warning systems and other escapeway aids such as a through-the-earth signaling and communication system, lasers and strobe lights are also addressed. The technological advancements that have been made can improve the state-of-preparedness for responders to underground emergencies and increase the chances of survival for escaping personnel.

By D. L. Pool

To increase metal recoveries and to minimize pollution by improved extraction technology, the Bureau of Mines investigated a hydrometallurgical technique to recover copper, lead, nickel, and cobalt from lead smelter mattes. The metals were converted from insoluble sulfides to soluble chlorides using a HCI-CI2-02 leaching system. Parameters studied in a 50-gallon, glass-lined reactor were the ratio of hydrochloric acid to chlorine, chlorine consumption per pound of matte, oxygen reaction pressure, and temperature. The matte material used contained, in percent, 19.7 Cu, 52 Pb, 2.9 Ni, 1.5 Fe, 0.38 Co, 0.19 As, 0.41 Zn, and 0.12 Cd. Extraction of Cu, Pb, Ni, Co, and Cd ranged from 92 to 98 pct, with concomitant extractions of Fe and As of <0.1 pct. The Cu and Pb were recovered as electrowon metals, while the Ni, Co, and Cd were recovered as mixed hydroxides.

Jan 1, 1981