Search Documents

Improve underground mine roof bolt support systems by alleviating problems associated with certain ground support systems currently being used. Approach Convert a passive resin-grouted roof bolt system into a uniform, tensionable roof bolting system. Background Resin-grouted roof bolts are one of the most common forms of ground support in U.S. underground coal mines. These support systems can be installed with a full-column of grout and be loaded with subsequent roof movements after installation. This is called a "passive" support system. An alternative to the passive support system is the mechanically-anchored, tensioned roof bolt system. This system is installed with resin grout. This system is designed to load or tension the support during installation by using a mechanical anchor, coupling, or threaded nut after the resin has properly cured. It is called an "active" support system and is used extensively for improved strata control in a laminated geologic deposition or in difficult ground conditions. To ensure that active bolts have been properly installed, the bolt loads must be checked by using a torque wrench or other suitable equipment. Unfortunately, this practice presents potential safety hazards and has limited accuracy. Laboratory and field experiments also reveal that the torque-to-tension ratio developed on active support systems can vary by 50% from bolt-to-bolt. Variations in bolt load installations can induce stress concentrations and lead to roof degradation or failure.

Jan 1, 1991

By David L. Moffatt

Considerable current interest is evident[l,2] in the use of transient electromagnetic methods for subsurface remote sensing. A transient method is discussed which uses a periodic video-type pulse containing a wide frequency range. A video pulse is used as an interrogating signal both for "target" identification and detection for relatively short depth (c 20 meters) applications in soil and soft rock media. If the medium is favorable, e.g., hard rock, greater depth applications appear to be feasible. The same procedures would be applicable for deep geological exploration but would require a substantial reduction in frequency and increase in target size. It should be noted that video pulse generators with 35 kv peak voltage and nanoseconds base widths are now within the state-of-the-art, thus significant power over broad spectral ranges is possible. In the design of a video pulse sounding system, 5 main problem areas can be identified; 1 ) selection of the pulse shape or spectral content of the video pulse, 2) design of a radiating structure which effectively couples such a pulse into the medium, 3) isolation of the radiating and receiving mechanisms, 4) realistically accounting for the dispersion and attentuation of the medium and the air-medium interface, and 5) interpretation or processing of the received signal waveform. Each of these problem areas will be discussed and illustrated with experimental and/or theoretical results. The Video Pulse Selection of the proper video pulse signal is dictated by 3 considerations, the maximum desired depth of penetration, the attenuation of the medium and the required resolution and size of the target. For a lossy medium, penetration and resolution are clearly at cross purposes and a compromise is necessary. The exact nature of the compromise is dictated by the application, but the spectrum of the video pulse should not contain any frequencies higher than the predicted cut-off, i.e., that frequency which is attenuated to the threshold level of the receiver. As a practical matter, it may be necessary to select 1 or 2 video pulses reasonably suited

Jan 1, 1973

By C. B. Manula, R. L. Sanford, R. A. Rivell

A central requirement for using simulation models is the need for retrospect testing to validate experimental conclusions. Acceptance of a model by managers and safety practitioners is more likely to depend on its tested performance in-the field rather than on the underlying logic or the validity aspects of the model itself. It is here that simulation bridges the gap between theory and useful design procedures. The original version of the rail haulage sub-assembly was success¬fully tested in the field (Sanford, 1969). However, the case studies that were described here involved single-stage haulage and restricted jobtypes from UGMHS. Since this report together with Volume VI (Production Subsystem) describes extensive changes and modifications to the rail haulage sub-assembly and UGMHS, field tests were necessary to verify both the rail model and the linking concepts to the Produc¬tion Sub-system. Mine Description The candidate mine selected for model verification works the 6 1/2 foot Pittsburgh seam. Shaft openings are used for manways and ventilation and a dual compartment slope for materials handling. In the bottom half of the slope, a hoist with track handles supplies and equipment. In the upper half, a 42 inch belt conveyor travelling at 450 fpm moves coal from a rotary dump to the surface. The immediate roof is shale with the first 12 inches taken during development mining. About 4500 raw tons are produced daily from seven face units and one spare working three shifts. At seven of the sections,

Jan 1, 1974

By W. R. Wrzensinski

This report presents the findings from a l-yr Bureau of Mines program in which sulfur concrete reinforcing materials were tested and evaluated to determine their resistance to corrosion. It also summarizes the permeation characteristics of sulfur concrete and the exemplary performance of precast, reinforced sulfur concrete structures in various industrial environments. The Bureau is furthering the development of sulfur concrete technology as part of a larger effort to find uses for the Nation's plentiful sulfur resources in construction materials. Sulfur concrete is a corrosion-resistant material that can be used in acid and salt environ-ments where conventional materials fail. Penetration of corrosion-inducing agents is minimized because of the low permeation characteristics of sulfur concrete.

Jan 1, 1988

By R. Barany

The heat of formation at 298.15 ° K of muscovite was determined by solution calorimetry . The value obtained for the heat of formation from the elements was -1,421.2 ± 1.3 kcal / mole , and the value for the heat of formation from the oxides was -55.9 ± 1.3 kcal /mole .

Jan 1, 1964

Provide a machine for economically drilling probe holes in coal mines (required where there's a possibility of unmapped, abandoned workings) to check for possible water flood or gas hazards ahead of the face. Approach A lightweight air-powered drill, that mounts on a light-weight frame anchored to the face with an expandable packer, is used to drill one or more probe holes. The anchor installs quickly and will lock the drill in any desired position. How It Works The drill is portable and can be broken down to small components for ease of transportation. One man can carry these sections through restricted access routes to the working place. Components that are separable are the anchor assembly, drill frame assembly, and drill motor assembly. The drilling sequence is as follows: A 2-inch-diameter anchor hole is drilled 2 feet deep. The fixed anchor tube is rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to inserted in the hole and the rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to the frame with a single locking pin. Installing the anchor and drill takes less than 12 minutes.

Jan 1, 1981

By Irven A. Jacobson

The thermal reactions of l-methylindole were studied in the temperature range of 525° to 627° C in a flow reactor. The major products consisted of 2-methylindole, 3-methylindole, indole, quinoline, hydrogen, and methane. 2-Methylindole is formed from 1-methylindole by an irreversible isomerization reaction. The 2-methylindole isomerizes in a reversible manner to 3-methyl-indole, the equilibrium favoring the 3-methyl isomer. Indole is formed directly from 1-methylindole. Quinoline is formed from l-methylindole, 2-methylindole, and 3-methylindole.

Jan 1, 1971

By J. Litsenberger, T. E. Marshall, P. R. Coyle, L. J. Prosser, A. T. Iannacchione

For the first time in an underground stone mine, the relationship between roof movement and microseismic emissions was examined in conjunction with two distinct roof fall areas. As roof monitoring increases in acceptance and monitoring technology advances, the goal of providing reliable roof fall detection systems to enhance the safety of underground mine workers moves closer to reality. Instrumental to reaching that goal is the ability to interpret accurately and completely roof movement and microseismic emissions, which can serve as precursors to roof falls. This paper examines the capabilities of convergence and microseismic monitoring systems to better understand roof rock failure mechanics and to anticipate roof falls. An understanding of how these techniques are used and how they interact with each other is critical in developing the most effective ground control strategy for our nation’s mines.

By Sivalingam Jeevan, R. L. McConnell

Ground check monitors may be made in several configurations. Each type has unique characteristics and provides different safety attributes when applied to different mine situations. In this paper, the monitor types are discussed in relation to the mine situations. It is shown that the selection of the monitor type can have a significant effect on the safety of the resistance grounded power system. The options are discussed, and the conclusion is drawn that only one monitor configuration can provide maximum safety. Unfortunately no monitors of this configuration are presently available. In addition, when the monitor capabilities and ground wire configurations are considered as a system, it can be shown that certain configurations will lead to maximum safety. This work was supported by U.S. Bureau of Mines grant G0144138.

Jan 1, 1979

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of three samples collected from the Kidney seam, in the Northern Field of the anthracite region. Removal of the sink 1.70 specific gravity material from the samples collected would result in greatly reduced ash contents at yields in excess of 90 percent. The Kidney seam, in the locations sampled, proved to be a low-ash anthracite containing an unusually high percentage of float 1.45 specific gravity material.

Jan 1, 1970

By R. V. Ramani, A. S. C. Owili-eger

The quantity of methane emitted into the mine atmosphere and the movement of gas through solid coal and the adjoining country rock are dependent on the physical properties of the medium, boundary con¬ditions, the initial gas pressure distribution, and the combination of natural and mining factors. Functional relationships between these factors are not yet known. Consequently, the development of rigorous mathematical models to predict methane flow into the mine air is difficult and to date no model has been reported which is capable of such a function. Thus far, empirical formulas available for the calculation of gas quantity released from underground sources require too much his¬torical data, not currently available. Again, these estimations are at best only crudely approximate. The numerical methods available have not been made practical enough for industry wide application. Therefore, the development of a relationship amenable to numerical analysis and practical enough for use in the industry would provide the flexibility lacking in analytical approaches. The mathematical models given in equations (7) and (8) are further attempts in presenting practical models for predicting the quantity of methane emission into the mine environment. Equation (7) is the steady state model and equation (8) is the unsteady state model.

Jan 1, 1974

By Foster Fraas

In this Bureau of Mines report, use of the photoemission of electrons to produce electric charges for the electrostatic separation of sonic dispersed minerals, which had previously been ground to pass a 43µ-opening sieve, is demonstrated. It appears that many of the oxides, carbonates, sulfides, and arsenides will respond to photoemission. Minerals least responsive are the oxides of silicon, the oxides of aluminum, and minerals that have a high concentration of these oxides. Although several synthetic ore mixtures did not yield to complete separation in a one-stage operation, it is probable that preliminary neutralization of the initial electric charges produced by powder dispersion will provide complete separation. That the separation can be carried out in air and without the use of reagents or heating, which are required in the present practice of electrostatically separating coarse granular feeds, is of special significance.

Jan 1, 1972

Provide sound battery safety guidelines for mine workers who maintain mobile surface mining equipment. Approach Battery-related accidents account for about 5 percent of all nonfatal disabling injuries in coal and metal nonmetal surface mines. These accidents occur despite the fact that appropriate battery safety technology (maintenance-free batteries, cable removers, fault detectors, hot-jumping systems, etc.) exists. Mine operators are not always aware of the safety measures that could be taken because this safety information is widely scattered in numerous unrelated technical reports, vendor brochures, and journal articles. A literature search of these reports and a review of relevant industry standards, handbooks, and references on battery safety, followed by discussions with mining company and MSHA personnel, provided the Bureau of Mines with the background necessary to develop procedures for proper and safe battery usage. These procedures were condensed and written in nontechnical language to serve as guidelines in assuring battery safety during maintenance of mining equipment.

Jan 1, 1986

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

5. General Escapeway Requirements 5.1 Escape Routes Present escapeway regulations state "Every mine shall have two separate properly maintained escapeways to the surface which are so positioned that damage to one shall not lessen the effectiveness of the other, or a method of refuge shall be provided when only one opening to the surface is possible." "Escape routes shall be a. Inspected at regular intervals and maintained in safe, travellable condition, b. Marked with conspicuous and easily read direction signs that clearly indicate the ways of escape." "Application. "Regular" intervals means at intervals no greater than monthly where conditions are stable and oftener where conditions may change." "Designated escapeways inclined more than 30* from the horizontal shall be equipped with stairways, ladders, cleated walkways, or emergency hoisting facilities." As can be noted in present and proposed regulations there must be two separate properly maintained escapeways. In most operations, the escapeways will consist of one route that is the normal travelway used in day to day operations. The second route is usually a return airway through old work areas. Based on this generally accepted practice, we will designate the two types as primary and secondary.

Jan 1, 1976

Detect fires in or near mine shafts, isolate smoke filled areas, and remotely extinguish fire. Approach A system (of sensors, automatic alarms, an aboveground control console, remotely operated ventilation doors, and sprinklers) has been built from off the-shelf components, and fire, tested in two mines. How It Works The system uses three different kinds of sensors that can detect the heat or smoke of a fire and automatically actuate alarms. When the alarm sounds in the control center on the surface, water sprays in the mine shaft and shaft station areas can be remotely turned on to deluge both the inside and the outside of the mine shaft's wooden support structure. To protect miners from toxic fumes, smoke control doors can be closed or opened, either remotely from the control center or directly by miners using the manual or electrical actuators at the door locations. Man doors built into each ventilation door allow persons to pass without opening the main door.

Jan 1, 1977

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.

By Richard V. Ageton

"Everyone admits that there are more accidents in metal mines than there should be but there is much difference of opinion as to the causes of accidents, whether avoidable or unavoidable, and the amount of responsibility attaching to the miner and the mine operator, respectively. However, it seems that one of the main reasons why there are so many accidents, is that there is so little general knowledge regarding their causes and costs. Some information regarding the costs and causes of metal-mine accidents is presented in this paper.The data contained were obtained from a study of the complete accident and medical reports of two large metal-mining companies, which carry their own insurance. Path maintain hospitals with competent medical attendants. One of these companies also maintains a very efficient safety bureau, consisting of a safety engineer, with two assistants who work in connection with the medical department, and with the safety committee made up from among the miners themselves.Daring the year of 1920, ""A"" Company employed approximately 900 men, and these men worked more than 270,000 shifts. There were 373 minor and major injuries, among these 900 men, hence assuming that each injured man was hurt cut once, 41 per cent of the men who worked in this mine received some kind of time-losing injury during the year. On account of these injuries the injured men lost 3731 shifts, and thus the time lost due to injuries amounted to approximately 1.4 per cent of the total number of shifts worked,"

Oct 1, 1923

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page, Linda J. McWilliams, Gerald J. Joy, Steven E. Mischler, Jon C. Volkwein

The United States National Institute for Occupational Safety and Health, through an informal partnership with industry, labor, and the United States Mine Safety and Health Administration, has developed and tested a new instrument known as the Personal Dust Monitor (PDM). The new dust monitor is an integral part of the cap lamp that coal miners normally carry to work and provides continuous information about the concentration of respirable coal mine dust within the breathing zone of that individual. Previous laboratory testing demonstrated that there is a 95% con?dence that greater than 95% of individual PDM measurements fall within ±25% of reference measurements. The work presented in this paper focuses on the relationship between the PDM and respirable dust concentrations currently measured by a coal mine dust personal sampler unit utilizing a 10 mm Dorr Oliver nylon cyclone. The United Kingdom Mining Research Establishment instrument, used as the basis for coal mine respirable dust standards, had been designed speci?cally to match the United Kingdom British Medical Research Council (BMRC) criterion. The personal sampler is used with a 1.38 multiplier to convert readings to the BMRC criterion. A strati?ed random sampling design incorporating a proportionate allocation strategy was used to select a sample of mechanized mining units representative of all US underground coal mines. A sample of 180 mechanized mining units was chosen, representing approximately 20% of the mechanized mining units in production at the time the sample was selected. A total of 129 valid PDM/personal sampler dust sample sets were obtained. A weighted linear regression analysis of this data base shows that, in comparison with the personal sampler, the PDM requires a mass equivalency conversion multiplier of 1.05 [95% C.I. (1.03, 1.08)] when the small intercept term is removed from the analysis. Removal of the intercept term results in a personal sampler equivalent concentration increase of 2.9% at a PDM measurement of 2.0 mg m-3.

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992

Improve surface mine haul-age truck safety and efficiency by providing a means for sensing the weight and distribution of the truck's load. Approach The safety hazards and the economic implications of overloading mine-haulage trucks were analyzed to determine the net effect of that practice on mine operations. The analysis indicated that: Ten to 25 pct overloading is typical; Higher haulage, tire, and maintenance costs occur due to overloading (a 20 pct overload was estimated to increase operating costs 7 pct per ton); Ten to 15 pct of haulage? truck injuries and fatalities are attributable to overload conditions, at a cost over one million dollars per year to the mining industry. Vehicle-weighing technology that conformed to the performance specification for an off-highway haulage truck overload detection system was selected for in-mine testing. How It Works Normally, volumetric estimates are made during the loading sequence which do not account for the varying ore density. Hence, the actual weight of a load is never precisely known. By providing a precise measurement, an overload detection system will not only indicate vehicle overloading, but will also show under-utilization of the truck. One system tested by the Bureau of Mines was the ?Load Analyzer" manufactured by Pactronics Corporation in California. This system consists of a meter-type analog readout for the cab console and three "Electrosensors" (linear variable differential transformers) attached to the main frame. Using conventional welding and brazing techniques, two sensors are attached between the front members of the engine sub-frame and the top of the left and right trailing arms (one sensor per arm). The same techniques are used to attach the third sensor to the rear centerline of the truck. between the main frame cross member and the A-frame. The readout unit on the cab console indicates by color-coding whether each sensor loading is under (green), at (yellow), or over (red) the pre-set rated load. The three-sensor configuration with in-dependent readouts also detects uneven distribution of the load.

Jan 1, 1984