Search Documents

By E. G. King

This paper reports measurements of low-temperature heat capacities and entropies at 298.15° K. of two copper ferrites (CUFe204 and CU0.75Fe2.2504). These substances, which occur in copper-smelting slags, have not been sujected to any previous direct thermodynamic investigation. The two copper ferrites are spinel minerals of the variate class. In previous investigations similar data were obtained for 13 other spinel minerals -7 of the normal class and 6 of the variate class. The entropies at 298.15° K. of these minerals have been compiled and revised as necessary in the light of present knowledge regarding structural randomness; entropy values, recommended for use in thermodynamic calculations, are listed.

Jan 1, 1959

By Thomas R. Bur

The order of identification and in same cases the magnitude of the elastic constants of an anisotropic material depends on the orientation of the cartesian coordinate axes with respect to a set of reference coordinate axes within the material; thus confusion will result unless standard orientations are used. In this paper the relationship between the cause (the internal fabric) and the effect (the elastic properties in this case) is discussed for single crystals and for polycrystalline and amorphous materials. While reference axes based on the cause are used in the IRE (Institute of Radio Engineers) standard for piezoelectric crystals) it is shown that a reference coordinate system that would be suitable and practical for all anisotropic polycrystalline and amorphous materials must be based directly on a three-dimensional expression of the effect. The conventions offered are similar to the IRE standards for piezoelectric crystals) but use the elastic coordinates of the wave surface which can be quite readily established experimentally as the reference coordinates.

Jan 1, 1969

By R. J. Matetic, D. Elsworth

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the field site. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 1995

Information Circular (IC) 9453 Roof falls continue to be the greatest single safety hazard faced by underground coal miners. During1996-99, 44 coal miners lost their lives in rock falls and nearly 2,400 were injured. In addition, nearly 6,000 non injury roof collapses were reported. Roof supports are installed to protect the miners, but support system failures contributed to most of these incidents. Reducing the terrible toll taken by ground falls continues to be a major goal of research by the National Institute for Occupational Safety and Health (NIOSH).During 2000-01, NIOSH conducted a series of open industry briefings on New Technology for Coal Mine Roof Support in Norton, VA, Charleston, WV, Evansville, IN, Tuscaloosa, AL, Price, UT, Glenwood Springs, CO, and Washington, PA. Drawing on many years of research undertaken by the NIOSH Pittsburgh and Spokane Research Laboratories, the proceedings describe what types of coal mine roof support are available, how they work, and when they should be used. The major subjects covered include roof bolts, standing roof supports, cable supports, and longwall shields. Some special topics are also addressed, including an analysis of roof fall accident statistics, techniques for better skin control, and material handling considerations. The proceedings volume also contains information on several important new technologies, which are described for the first time, e.g., guidelines for selecting roof bolt

Aug 1, 2001

By Thomas V. Falkie, R. Venkataramani

1. Summary This investigation is concerned with description of the loading function at the underground coal face, and the identification of varia¬bles - geological, geometric, mechanical, and operational - that affect the loading function. The immediate objective of this work was to provide information for operations-research studies as applied to underground coal mining, and the broad objective was to provide guide¬lines for planning and equipment selection in underground coal mining. The loading function was expressed as -a statistically-developed linear mathematical model. Originally, fifteen independent variables were considered which potentially could have influenced the loading function. These variables were constructed on the basis of measurable or estima¬ble geometric and geological properties at the working face, mechanical characteristics of the mining machine, and certain operational proce¬dures of mining. The original model explained 64.0 percent of the experimental variation. The final condensed model explained 54.1 percent of the experimental variation in terms of only five indepen¬dent variables, namely: 1. Ratio: width of cut/total width of cutter 2. Ratio: height of cut/diameter of cutter 3. Total horsepower of cutter-drive motors 4. Rotation speed (RPM) of cutter 5,. A subjective estimate of machine quality and operator skill Certain limitations were found to exist in the evaluation of the variables. Principle among these limitations was the impossibility of precise measurement of tonnage loaded in certain instances.

Jan 1, 1972

By Thomas V. Falkie, R. Venkataramani

The purpose of this work was to Investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors - geometrical , geological, mechanical, or procedural - which affect the delivery rate, and to develop quantitative rate-descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily Influences the loading function The geometrical factors -the dimensions of the work area In relation to the dimensions of the mining machine -were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent Independent variables. It is expected that this work will be useful In operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Sep 1, 1972

By D. R. Forshey

The recent occurrence of fatal accidents in copper mines, presumably due to premature ignition of loaded holes by the heat from reacting ammonium nitrate-fuel oil (AN-FO) and pyrite-bearing ores, has led to an examination of this reaction. The reactivity of prilled AN-FO mixtures with pyrite-bearing ores and the effects of water, dilute sulfuric acid, and potential inhibitors on reactivity of the mixtures were evaluated. Initiation of an exothermic reaction was observed as low as 150° F with acid in the absence of inhibitors. Low concentrations of urea, calcium carbonate, zinc oxide, and magnesium oxide were effective in inhibiting the reactivity of the mixtures. The temperatures produced during the reaction of mixtures of AN-FO and pyrite-bearing ores, in the absence of inhibitors, always exceeded the temperature at which electric blasting caps are thermally initiated.

Jan 1, 1968

By R. A. Friedel

Data on compositions of natural substances are important in the study of possible interrelationships. The similarity of the low molecular weight alkane isomers from crude oil and Fischer-Tropsch catalytic synthesis product has been reported (8).3 A similar composition for the alkane isomers from high-temperature coal carbonization has been found. The composition of the C4 to C 7 alkane isomers from these three sources can be calculated quantitatively with the equations previously developed to calculate alkane isomers in Fischer-Tropsch product. An KM sting reversal of the concentrations of the monomethyl isomers from C6(2 Me > 3 Me) to C7 (3 Me > 2 Me) occurs in all three products; fragmentary comparisons at higher carbon numbers indicate some dissimilarities. Naphthene isomers in the C6 to C7 range for crude oil and high-temperature coal carbonization also have similar compositions. Aliphatic hydrocarbons from low-temperature coal carbonization processes are considerably different, consisting mainly of normal alkanes.

Jan 1, 1968

By G. W. Murrie, W. P. Diamond, C. M. McCulloch

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over- burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

By R. V. Ramani, V. T. Burgos, J. A. McClay

Cost Systems Cost systems are organized methods of collecting, allocating, and accumulating resource utility expressed in terms of money. There are two major spheres of cost accumulation: financial accounting and cost accounting. Financial accounting deals primarily with historical costs and provides a means of measuring and recording cost events which have al¬ready taken place. While there are no legal requirements to control the methods of recording and reporting cost data in the United States, the procedures in use are guided by professional organizations such as the American Institute of Certified Public Accountants. The final pro¬ducts of financial accounting practices are the income statement and balance sheet which describe the financial status of the organization under study. Cost or managerial accounting is an expansion of financial ac¬counting procedures, providing more detailed cost breakdowns on present operations with one objective being the projection of present costs into the future. The projection process tends to limit the accuracy of the information; however, to management and project justification per¬sonnel, data on future operations tends to be of greater value. The basic principle behind cost accounting is the cost cycle. As products are developed from raw materials, the value of the work-in¬process increases due to the cost input of the various fabricating ele¬ments. Thus, from the basic input elements of facilities, labor, and raw materials, costs are added to each unit of production as a function of the work performed on that unit.

Jan 1, 1975

By Launa Mallett, Michael J. Brnich

The first step to emergency preparedness is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen all at once. Risk assessments are used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. While the examples provided in this training package are specific to mine fires, the concepts and tools can be applied to any mine hazard. Purpose: This training package was developed to assist instructors, as they: 1) determine how to use risk assessment to improve preparedness for mine fire emergencies and 2) present risk assessment concepts and tools to trainees. Audience: This package is appropriate for workers/trainees from all types of mines. A risk analysis can be conducted by anyone familiar with the location(s) being studied. Why Conduct a Fire Risk Assessment? During a risk assessment, hazards are evaluated in terms of the likelihood that a problem may occur and the damage it might cause. Mine fire preparedness requires consideration of all possible fires that could occur. However, at a given mine some fires are more likely than others and some would result in greater damage than would others. Conducting a risk analysis identifies these differences. The results can be used to target resources at the types of fires that are most likely and/or are most destructive. Hazards that are very likely to result in fires that would do considerable damage to people and property should be targeted first for remediation and/or effective response if remediation isn't possible. Potential fires that are less likely or that would have less severe consequences are identified for attention later, after the more serious situations have been addressed.

Jan 10, 1992

By Bruce K. Cantrell, Winthrop F. Watts

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989(1), which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This report reviews, available diesel exhaust aerosol and gas measurement techniques. Measurement of human exposure to toxic agents is the first step in determining the exposure-dose-response relationship. It is a fundamental step in risk assessment. Measuring exposure to diesel exhaust pollutants is particularly challenging due to the complexity and variability of exhaust components. This paper reviews current occupational health standards for diesel emissions and available diesel exhaust gas and aerosol measurement techniques. Although surveys in mines have primarily assessed diesel exhaust exposure using diesel particulate matter (DPM) some exhaust gas measurements have been used as indicators of exposure. DPM is emphasized because it is a major component of diesel exhaust, is suspected to make a major contribution to the health hazard, and is measurable. OCCUPATIONAL HEALTH STANDARDS Occupational exposure surveys of diesel exhaust frequently measure regulated pollutants, or pollutants that are suspected carcinogens, even if no permissible exposure limits (PELs) have been established. In the United States, various organizations recommend a range of allowable values for diesel exhaust gaseous constituents, including carbon monoxide (CO), carbon dioxide (CO2), sulfur dioxide (SO.), nitrogen dioxide (NO2), nitric oxide (NO), and formaldehyde (HCHO). Table I summarizes these recommended levels, showing 8-hour or 10-hour time-weighted-average values where available; where these are not available, 15-minute short-term [ ]

By H. Robert Ensminger

As a result of the new mining law implemented in August 1985 and the programs conducted by the Institute Ecustoriano de Mineria (INEMIN), which was created by this legislation, there was considerably greater activity in the nonfuels mineral sector during 1986. Over the next 2 years, INEMIN will be developing a national mining plan that will guide Ecuadorean mineral development for the balance of this century. As stage one of INEMIN's mineral study, historical records were reviewed and 300 abandoned mines and 1,200 unexplored mineral deposits were available for further investigation. In 1986, INEMIN established 5 branch offices and negotiated 250 new mining contracts with foreign companies valued at $16 million. Despite all this activity, INEMIN officials estimate that 100,000 square kilometers remain available for claim staking. Technical assistance contracts were signed with Belgium, the Federal Republic of Germany, Italy, Spain, and the United Kingdom, to assist in a variety of assignments ranging from helping prepare the national minion plan to the development of industrial mineral deposits.

Jan 1, 1988

By G. B. Atkinson

The Bureau of Mines, in cooperation with McDermitt Mine, investigated a method for recovering mercury metal from mercury sulfide flotation concentrate by a hydrometallurgical technique. This preliminary report shows the feasibility of leaching mercury with a cupric chloride solution and electrowinning mercury from the solution. Proposed chemical reactions are shown in equations 1 through 3: 2CuC12 + HgS + 2CuCl + HgC12 + S°; (1) electrolysis HgC12 ?Hg + C12; (2) 2CuC1 + C12 ? 2CuC12. (3) A bench-scale leaching-electrowinning apparatus capable of treating 2.36 kg of sulfide concentrate in 11 days was operated continuously. An acid chloride solution containing, in grams per liter, 70 Ca, 60 Cu, 30 Fe, and 80 Hg was used as both leachant and electrolyte; 99.5 pct of the mercury was solubilized from the sulfide concentrate. Electrolysis of the leaching solution recovered mercury metal at an average current efficiency of 32 pct and an average energy consumption of 1.2 kwhr/lb Hg. Results from a preliminary economic evaluation indicated that a plant producing 31,500 flasks of mercury per year would have a capital cost of $3.7 million and an operating cost of $62 per flask of mercury.

Jan 1, 1983

To provide safer and more efficient mine operations by improving the operational performance of underground trolley line communication systems. Approach The dc trolley line provides a convenient means of In-mine communication since it can carry signals to each phone on the system whether the phones are in mine vehicles or in a fixed location such as that of a dispatcher. In many cases, however, the system does not perform satisfactorily. Short communication range, noise, and dead spots commonly interfere with effective communication. These problems are inherent with the trolley line, which was designed to transmit power and not communication Signals. As a power line, the trolley line is connected to rectifiers and feeds many loads such as motors, water pumps, track block lights, etc. Each of these devices represents a low impedance radio frequency (RF) shunt that seriously reduces carrier communication Signals. Performance is therefore often poor and can be improved only if the effects of the various shunts can be reduced. The Bureau of Mines has developed numerous methods applicable to either existing or planned phone systems which can improve communication range and reduce the shunting effects of the various loads.

Jan 1, 1983

Objective Develop a method to warn of hazardous conditions and enhance safety during operation and inspection of vertical mine shafts and hoists. Background Mine hoisting is the most critical and potentially the most dan¬gerous operation in underground mining. Many hazards are related to falls of miners and materials, ground instability, and malfunction or lack of safety devices. All have the potential to cause a cata¬strophic accident. A condition known as "slack rope" is particularly dangerous, expecially if it occurs without the operator's awareness. The most common occurrence of slack rope is in metal or nonmetal mines that have a history of ground control problems near the "haft. Approach Studies of hoist safety features and Mine Safely a and Heath Administration (MSHA) accident statistics suggests a need to measure wire rope tension, conveyance speed and position, and shaft guide misalignment. The most accurate data are obtained directly from the conveyance. Such data could warn of potentially dangerous situations during hoisting operations, as well as during inspections, maintenance, and lowering of large equipment. Figure I shows the concept for monitoring wire rope tension, conveyance position, and guide displacement. Progress to Date A conveyance-mounted system has been developed that monitors rope tension: hoist conveyance position, speed, and load; and shaft guide misalignment. A "flex-beam" load sensor mounted just above the- conveyance protects against slack and tight rope. The measurements are transmitted 60 times a second via wireless equipment from the conveyance to the hoist room. An encoder mounted on the conveyance eliminates the need to correct the position because of rope stretch. Figure 2 shows the encoder wheel and guide displacement sensors being mounted on a cage in¬spection deck. A potentiometer monitors misalignment of the shaft guides during inspections. Information about the cage or skip can be acquired by the shaft inspector using a hand-held indicator. Inspection can also he conducted remotely from a station or hoist room using the wireless link to a laptop computer. Figure 3 shows test results from a simulated slack rope condition. Patent Status NIOSH has a patent pending on this device entitled "Cable-Load¬Sensing Device." For More Information NIOSH is seeking cooperators to assist in further tests of this technology to improve hoisting safety. Additional information can he obtained by contacting Michael J. Beus, Steven Iverson, or Elaine Cullen, Technology Transfer Officer, NIOSH, Spokane Research Laboratory, Spokane, WA 99207 at (509) 354-8000.

Feb 1, 1998

By Guy A. Johnson

This Bureau of Mines report summarizes the results of efforts to develop reasonably priced, reliable mine shaft fire and smoke protection hardware for metal and nonmetal mines. The hardware was incorporated into a viable prototype system that would minimize fire and smoke hazards. The design of the system had to be sufficiently flexible to be utilized in a wide variety of metal and nonmetal mine shaft and shaft station configurations. As a result of long-term, rugged field tests, an improved (second generation) system was developed. The hardware is now commercially available.

Jan 1, 1978

By F. W. Hoertel

The effects of certain process variables on the grain size, grain type, and microhardness of vapor-deposited tungsten were established, and the near-optimum parameters and the efficacy for the vapor deposition process were determined. No significant change in the grain size or microstructure resulted from ultrasonic vibration of the substrate during deposition, from variations in the hydrogen (H2) to tungsten hexafluoride (WF6) ratio, or from small increases in reaction-chamber pressure. Near-optimum conditions were continuous deposition at atmospheric pressure, a deposition rate of 2-mils thickness/square inch of substrate area/hour, a temperature of 5500 C, and a hydrogen to WF6 ratio of 4:1. The addition, individually, of about 2 volume-percent of butane, 24 volume-percent of carbon dioxide, or 4 volume-percent of propane to the hydrogen and WF6 mixture produced deposits with the finest grain size for each gas. A corresponding increase in microhardness accompanied the decrease in grain size. The addition of gases did not alter the columnar microstructure found in vapor-deposited tungsten.

Jan 1, 1966

By L. M. Chan, D. R. Carlson, J. H. Johnson

"This paper presents an apparatus and procedures to implement a methodology for controlling ambient air quality in a confined working environment, such as an underground mine, an underground storage area, or a tunnel. The air quality control methodology is directed at limiting the quantities of exhaust pollutants emitted by diesel-powered vehicles into the confined space by identifying vehicles that are excessive polluters. The methodology is based on tailpipe and ambient air measurements in the confined space, and the ambient air threshold limit values (TLVs) for the various diesel exhaust pollutants. The methodology consists of two computational methods; a deterioration criteria computational method to identify excessive polluting vehicles, and an engine performance computational method to determine engine performance and to provide information needed to diagnose engine faults. The methodology is designed for implementation in conjunction with a preventive maintenance program.The first part of the paper describes the mine air and tailpipe emissions measurement apparatus and techniques used to obtain data. This is followed by sections discussing the deterioration criteria and the engine performance computational methods. A section discussing some common engine emissions-related faults is also presented lastly, a proposed procedure to implement the methodology including a possible hierarchical structure for mine personnel involved to implement the procedures is presented.INTRODUCTIONDiesel-powered mining vehicles are gaining Popularity in underground coal mines and are almost universally used in underground non-coal mines due to their mobility, flexibility, and higher productivity. However, noxious gases and particulate matter in diesel engine exhaust are a concern because of the potential for being harmful to the health of miners. Diesel exhaust pollutant concentrations out the tailpipe of a mine vehicle change with time due to engine wear, inadequate maintenance, improper adjustments and other factors. This deterioration in pollutant concentrations, if not properly controlled, may adversely affect the air quality in an underground mine. To provide assurance that a clean and healthful work environment are maintained, a program is needed to identify and repair diesel engines that contribute to poor air quality. Also, earlier detection of deteriorated engines will make preventive maintenance possible, thereby eliminating further deterioration and possibly complete breakdown. Preventive maintenance also increases engine life and equipment availability in production which in turn will result in decreased operating costs."

Nov 1, 1995

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A. 3 Program Description The computer program developed to simulate events in the case of fire in the mine is described in this section The description is divided into three parts. 1. Program Capabilities This part summarizes what inputs can be changed, what outputs can be obtained and demonstrates program flexibility through suggested uses.

Jan 1, 1976