Search Documents

By S. J. Page, J. A. Organiscak

Airborne respirable dust surveys were conducted at six surface coal mines to investigate the effectiveness of dust control methods used on rotary rock drills and bulldozers. Dust controls commonly used on drills include a dry dust collection system, exhausting from a shrouded area around the collared hole, and an enclosed drill operator cab, filtering airborne dust from the cab. Bulldozers are also typically equipped with an enclosed operator cab as a dust control measure. Airborne respirable dust sampling was conducted near each equipment's source of generation and inside its enclosed cab. Silica analysis was performed on the dust samples to determine the percent silica content in the dust generated at the six mining operations. An additional eight- month follow-up of dust sampling was also conducted in the enclosed operator cabs of several rock drills and bulldozers. Data were analyzed for long-term variability of accepted control methods to abate dust and silica levels. The highwall rock drill was the major and most variable dust source as compared to the bulldozer, generating dust levels, on average, one order of magnitude higher than dust levels of the bulldozer. Four of the six drills surveyed had dust containment and capture problems at the shrouded drill table above the lple. Repairs or modifications to three of the drill dust collection systems were shown to reduce dust levels by more that 50% next to the shrouded drill table. The enclosed operator cabs provided more than 90% and more than 40% lower dust levels than at the dust source for the drill and bulldozer, respectively. Long-term sampling of several of these highwall drills and bulldozers showed that the dust levels in the drill cabs were frequently higher than 0.2 mg/m3 and more variable than in the bulldozers. The bulldozer dust levels were frequently below 0.2 mg/m). Future research should focus on improving some of the deficiencies present in the drill's primary dust collection system, and developing quality control methods to ensure the integrity of enclosed cab protection for equipment operators.

By Ronald D. Hill, Elmore C. Grim

1. Potential groundwater pollution resulting from large-scale surface mining in western states should be evaluated. 2. Criteria should be developed for the design, construction, operation, and abandonment of sediment ponds for maximum removal of suspended solids. 3. Methods should be developed for reducing suspended solids discharges from surface mines to less than 30 milligrams per liter. 4. A manual should be developed in the form of guidelines for sediment and erosion control planning and implementation. These guidelines must be designed to cover all phases of the coal surface mining operation (i.e., before, during and after mining). 5. A mine road manual should be developed for use by surface mine operators and State and Federal Agencies. Erosion, water control, and dust control should be covered in detail. 6. The block-cut, head-of-hollow fill, and mountain-top removal methods and techniques of contour mining should be evaluated, designed, and ultimately demonstrated in steep, mountainous terrain. Designs should be prepared for single and multiple seam applications. The demonstrations must show that these mining systems will secure rapid achievement of reclamation require¬ments and provide maximum, safe, economic coal recovery in an environmentally safe manner. 7. A Blasting Manual should be developed for use by industry and enforcement agencies. Stress should be placed on how to keep vibration levels and air blast pressures well below accepted safe criteria. Also, methods that can be used to control noise should be listed. 8. Investigations should be conducted on the effect of continued vibrations from blasting on structures that are near quarries. 9. Additional guidelines need to be developed for sampling and analysis of overburden material and associated coals for trace elements and noxious strata. Samples are extremely sensitive, and the source and manner of their collection, handling, storage, and treatment, as well as the techniques of analysis, need to be developed and described. This information can be used to predict possible future problems.

Jan 1, 1974

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Federal Bureau of Mines. The purpose of the examinations was to disclose new sources of industrial limestone and to indicate the commercial potentialities of little-known and undeveloped deposits. These examinations were part of a long-range program of investigation of mineral resources of the Pacific Northwest. The following report on the Whitechuck travortine deposit is one of a series prepared in the course of the investigations.

Jan 1, 1949

By F. C. Trutt, J. Sottile, J. L. Kohler

Presented in this paper is a theoretical review of the relationships that should exist between electrical winding parameters and the mechanical vibration of a-c machine elements under normal and faulted operating conditions. Also included is data from an experimental study that relates stator vibration and bearing vibration to selected winding faults in a synchronous machine. Consideration of these results indicates a significant relationship between electrical deterioration and mechanical vibration and thus provides the motivation for additional study and a basis for future applications.

Objective: The Roof Monitoring Safety System (RMSS) provides a first step in roof behavior awareness. By understanding and measuring roof movement in an underground mine, the potential for injuries or fatalities to mine workers from fall of ground can be lessened. Also, officials at an underground mine with a history of data on roof movement are better prepared to make a decision on remedial actions if falls of ground become a problem. The RMSS provides a safer, simple, and inexpensive means for measuring roof movement.

Aug 1, 1998

By Andrew B. Cecala

While various types of equipment are used in bulk material processing plants to control respirable dust, the equipment often doesn't adequately protect workers. One cost-effective way to supplement your existing dust control equipment is to install a whole-plant ventilation system. This article outlines research by the National Institute of Occupational Safety and Health (NIOSH) on using whole-plant ventilation in two mineral processing operations to reduce respirable dust levels. Information also covers how to design a ventilation system for any bulk material processing plant.

By Mark Larson, Doug Tesarik, Joe Shoemaker, Brad Seymour

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the backfilled entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backfill provided stability for the roof and floor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right mine through and should provide beneficial case study information for other longwall backfilling applications in the future.

By A. B. Hooker, L. C. IlsLey

Several ignitions or mine pa, which might have led to explosions, and at least ona mine fire attributed to heated leg wires of electric detonators, have occm.rred. at rn1::.es in which outside shot firing is practiced. Photographs taken at one mine ind.la.ted. that the wires became red hot during firing. These results having been --i·-led. to the .Lttention of the electrical section of the Bureau of the Mines, ignitions the tests and to reportd aid in herein preventing were made future to trouble determine of if this possible kind, the cause of The investigation, which 1• considered preliminary, included tests to determine the conditions tha.t cause gas ignitions from heated. leg wires of electric and. of detonators, copper leg possible wires, remedies The tor samples such of heating, wire used. and in the the relative test were behavior the of reg\llar ironDa. Pont iron and copper leg wires (No, 22 A,W,G.) C\1t from Du. Pont electric detonators.

Aug 1, 1922

By L. C. IlsLey

The Bureau of Mines has collected field data and made laboratory investigations of trailing- cable performance in the hope of developing a better and safer cable for use with permissible mining machines . Because of their better insulation and performance , only rubber- sheathed cables were finally considered . The cables tested represented the product of six manufacturers . : After consideration of the results of the preliminary investigations , the conditions under which cables are used in mines , and the better performance of the later types of cables that were submitted as the investigation progressed , the bureau formulated a performance - test requirement and notified the cable manufacturers as follows : The hazards of the trailing cable are such that the bureau has been unable to extend beyond the machine its formal approval to cover the cable as at present developed . However , in the attempt to reduce the hazard as much as possible , cables passing certain tests will be recommended for this service and it is hoped that several cables will be developed to meet this requirement .

Sep 1, 1930

By J. E. Chilton, C. R. Carpenter

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro- chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1- to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light- emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 1992

By Hans M. Cassel

The specific objective of research presented in this report was clarifi- cation of physicochemical fundamentals of the mechanism of dust explosions. The equipment, techniques (chiefly photographic), and dusts (chiefly graphite and light metals) employed are described. From behavior of individual par- ticles, conclusions are drawn as to their cooperative function in ignition and combustion of dust clouds. Results are interpreted using thermal theory as accepted for combustible gas mixtures. Radiative transfer across the flame front, as a characteristic of dust flames, is given particular atten- tion. Related studies by other investigators are discussed.

Jan 1, 1964

By P. Delogne, L. Deryck, R. Liegeois

So far as the propagation of electromagnetic waves is concerned, an underground tunnel behaves like a pipe or hollowed waveguide. Waves propagate in this tunnel with a low attenuation only if their frequency is higher than a so-called critical frequency which depends on the shape and mostly on the cross -dimensions of the tunnel and which value is in the neighbourhood of several tenths of MHz. However, when a metallic conductor is stretched along the gallery the electromagnetic characteristics of the latter are considerably modified and the effect of the cut-off frequency disappears; this is due to the fact that the gallery equipped with such a conductor works like a coaxial cable where the conductor serves as the outward conductor and the wall of the gallery as the return conductor. This is the principle of the monofilar waveguide cable which has been perfectly studied by Gabillard. Two mean characteristics of the monofilar mode are as follows: first of all, when the cable is suspended in the middle of the cross section of the gallery, the electromagnetic field occupies all the space between the wire and the walls of the gallery. When the wire is close to the wall, the electromagnetic field tends to become concentrated between the wire and the wall, with the consequence that, with the given monofilar mode power, the aerial of a receiver standing somewhere in the tunnel will capture a weaker and weaker signal. Secondly, owing to the fact that the mode of monofilar propagation uses the ground as return conductor, its power of propagation is considerably diminished; the closer the wire is to the wall the higher the attenuation, for only a very small part of the wall is utilized as return conductor. To cover great distances, everything else being equal, two or more conductors must be placed in the gallery. If the distance between two conductors of a cable is much smaller than the distance between one or other of the conductors and the walls; or again if one of the conductors surrounds the others and forms a screening, two sorts of modes appear: on the one

Jan 1, 1973

By John W. Buch

"INTRODUCTION The Ruhr coal basin is estimated to cover an area of more than 1,000 square miles. Here, the total thickness of the coal bearing formation (Carboniferous) is 10,500 feet, and drilling-hole have revealed 92 coal beds with a total thickness of 262 feet. 6/ Beds pitch from 0 to 90 degrees and about 70 percent of the wartime production came from beds that pitched less than 30 decrees. 5/For example at the Minisiter Stein mine, there are 24 minable coal beds ranging from 80 centimeters. (2 ft., 7 1/2 in.) to 250 centimeters (8 2 1/2 in.). The vertical thickness of the measures is 1,000 meters (3,200 ft.), and at this mine the deposits are covered with 150 meters (500 ft.) of surface wash. The cross section (fig, 1) at Fritz mine; Hoesch, A.G., Essen, Ruhr, is characteristic, The mines have been developed and worked to vertical depths of 2,000 to 2,500 feet by vertical shafts; main-level intervals are 500 to 700 feet apart. Haulage roads are straight, driven in rock, and centered as nearly as practical between property boundaries. Levels are sectionalized by driving crosscuts at right angles to the main haulage road on 800- to 900-foot centers. The roads are the main transportation arteries for the use of trolley or Diesel locomotives. A plan of the sixth main level (fig. 2) at the Bruchstrasse mine; Gelsenkirchener A.G., Bochum, illustrates main-level development and,sectionalizing with crosscuts. The cross section in figure 3 is that of the fourth crosscut west at the same mine."

Oct 1, 1946

1. In 2003, a total of 734 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Examples of nonmetal mining operations include, but are not limited to, the mining of clay, shale, barite, potash, trona, phosphate rock, rock salt, gypsum, talc, gemstones, mica, perlite, and pumice. • Nonmetal mines comprised 5.1% of all mining operations. • Nonmetal mining operations are located in all states and territories except Alaska, Delaware, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands. • Mines producing common clay comprised 28.6% (n = 210) of all nonmetal mining operations.

Feb 1, 2005

By Clyde E. Eilliams

In recent ye.ars much intere,t has been centered on the possibility of pro­ducing alumina from clq, a.nd proposed methods tor the recove:r,v of alumina are appearing constantly in parent lit,erature, As a good· grade of clay contains from 30 t<> 40 per cent of al"WDina, the prospect of tecovering it is alluring, al though obviously ditfieul t. A patent typical of m projected thermal processes is that 0£ Paul Migu.et, (U, S, Patent No, l,376,563) entitled nprocess for the preparation of pure alkaline alu:ninates.'' Re proposes to prepare alkaline a.luminate by fusing clay, lime, and acrap iron with a reducing aget in the electric furnAce, thereby reducing the silica a.r.d formin1s calcium alumina.te and ferrostlicon, The calcium aluminate, being lighter, would. float on top substantially free from foreign oxides, It could. then be tapped ott, cooledf ana later crushed and leached with aodium carbonate solution to torm, by double decomposition, sodium aluminate, and calcium carbonte. The fonMr is soluble and yields readily aluminum hydroxicie. 'l'he ferrosilicon wo'Uld be r,covered as such and sold at a profit.

Aug 1, 1922

By E. P. Youngman

Prior to 1854 the provincial legislatures in Austria enacted their own mining laws. The confusion that resulted from the existence of different codes when mining began to be conducted by modern methods forced the drafting of a law to cover all mining operations of the country. Such a general law (allegemines österreichisches Berggesetz) came into effect May 23, 1854, in the old monarchy, with the exception of Hungary, which had its own special laws. This general law of 1854 is still the basic mining law for Austria, although it has been amended and supplemented by a mumber of acts.

Nov 1, 1931

By Gerrit V. R. Goodman, Jeffrey M. Listak, John A. Organiscak

Data on dust control practices, geology, and occupational exposures were gathered for approximately eighty underground continuous mining units. Despite silica contents in excess of 5%, nearly forty units successfully maintained silica concentrations at or below 100 µg/rn3 on a majority of occupational dust samples while the remainder had difficulty maintaining this level. These two sample sets were termed group A operations and group B operations, respectively. Analyses of productivities, geologies, and dust control parameters revealed only minor differences between these two groups. Subsequent analyses of face ventilation design showed considerable differences in silica exposure and silica content between group A and group B at the continuous mining machine and roof bolter operator occupations. These differences were minimal when using exhaust curtain ventilation with a dust scrubber&apos;, This face ventilation system may benefit operations having difficulty controlling silica dust exposure and silica dust content. Finally, the collected data showed that occupational samples from group B operations possessed generally higher silica exposures and silica content than similar samples from group A. The single head roof bolter (helper) possessed among the highest silica exposures and silica contents in both groups.

By Peter L. Swanson

NIOSH has developed an automated PC-based seismic monitoring system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network (LAN) is a central feature of the system. Design requirements include (1) the use of lowcost, off-the-shelf, data acquisition and computer hardware, (2) the capability of automatically merging waveform data sets from different types of monitoring systems, (3) delivery of raw and processed data underground and on the surface, as well as to remote sites, and (4) automated data collection and processing over long periods of time without the need for human intervention. Current mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface and provide 20 to 40 stations within a radius of several kilometers. Event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system&apos;s hardware and software components, examples of installations in hard-rock and coal mines, and a few observations from western U.S. longwall coal mines.

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

MFIRE is useful for the analysis of ventilation networks under thermal and mechanical influence MFIRE simu¬lates a mine&apos;s ventilation system and its response to altered ventilation parameters, external influences, and internal influences Extensive output enables detailed quantitative analysis of the effects of the proposed alteration on the ventilation system MFIRE was written in FORTRAN 77 and compiled with Microsoft° FORTRAN for the Intel 8086-8088 central processing units The source code is listed in appendix A for users who wish to modify the source code for operation on other computers MFIRE MODIFICATIONS OF MTU-BOM CODE The program described in Bureau of Mines Informa¬tion Circular 8901 has become known as the MTU-BOM codes MFIRE is an evolutionary product of the MTU¬BOM code with major improvements and enhancements 6 For users previously familiar with the MTU-BOM code, the following is a listing of the major improvements and enhancements incorporated by MFIRE 1 The length of an airway is an input value, LA The elevation difference of the airway is calculated from the elevation input, Z, in both programs It is possible for a data file to describe an airway that is shorter than its el¬evation difference The MTU-BOM code does not check for this error and uses the values of LA and Z This does not cause a computational problem, only a simulation problem MFIRE issues a warning message for this case, and the airway length is made equal to the elevation dif¬ference if LA is less than Z 2 To evaluate rock temperatures (average wall surface temperature of airway before a fire), it is assumed that the air temperature at an airway entrance is equal to the air temperature at the airway starting junction, and that the air temperature at the airway exit is equal to the air tem¬perature at the exit junction. The MTU-BOM code follows this assumption in all cases When a rock temperature of less than 0° F is calculated, an average temperature is used to represent the rock temperature of the airway MFIRE uses the same principle, except the consideration of unlikely rock temperatures When the exit junction of an airway is the atmosphere (a fixed condition junction), the air tempera¬ture at the exit is made equal to the air temperature at the airway beginning If an unlikely value of wall temperature (<0° F or > 150° F) results from calculations, a message is issued and the rock temperature is set equal to the air temperature at the airway exit The program user can always input rock temperature (TROCK) for an airway to override the calculated value. 3 MFIRE allows use of an optional reference airflow rate to define and limit the heat generation of a fire source This allows the simulation model to more closely resemble a real fire and to improve simulation conver¬gence Heat generation corresponds, but is not linearly related to airflow rates reaching the fire In the simula¬tion, heat generation is calculated from oxygen consump¬tion and is directly related to the variable incoming airflow Use of this optional reference airflow rate allows the heat generation to vary, but in a damped, user defined manner When the airflow rate passing through a fire source is equal to its reference airflow rate, the data items describ¬ing the fire source are not modified If the airflow rate is lower or higher than its reference airflow rate, the data items used to define the fire source are modified according to the following equations

Jan 1, 1990

By Bob Thomas, Syd Peng, Quanzhong Gu, Gene Wilson, Gerald L. Finfinger

Identifying the properties of overlying rocks in underground mining operations is important to ensure the appropriate roof support design is used to maintain stability of the mine entries. Recently J. H. Fletcher & Co. developed a monitoring and control system for roof bolters for the underground mining industry. The system records the drilling parameters used during roof bolt drilling and the information can provide insight into the physical properties of the roof strata. The parameters include thrust, rotational speed, torque and velocity and the measurements are collected every 0.1 second during the operation. The drilling parameters were analyzed to determine the application of identifying the strength of rocks being drilled from the measurements. The data was converted into the specific energy of drilling which is a measure of the amount of energy required for removing a given unit of rock during a drilling operation. The laboratory studies completed to date indicate a fairly high correlation between the specific energy of drilling and the unconfined compressive strength of :he rocks that were drilled. Additionally, the drilling parameters were shown to be effective for identifying the presence of fractures or bed separations between rock layers. The thrust, torque and specific energy of drilling were all good indicators for identifying the fractures or separations. Regardless of the drilling parameters used during the drilling experiments, the location of the fractures were identified. In order to determine the application of the drilling parameters for identifying roof rock properties, two series of experiments were conducted. The first series of experiments used three "manufactured" roof layers that had various rock samples embedded in concrete blocks. The rock samples included three types of sandstone, marble, and argillite. Another concrete block was poured with foam inserts to simulate large bedding separations (2 to 8-in). Two other manufactured blocks were constructed using high-strength concrete with cardboard layers embedded to simulate smaller fractures or bedding separations. The size of the cardboard layers varied from 1/8- to 1-in thick. One of the blocks had the cardboard layers embedded at an inclined angle to determine the effect of the orientation on the drilling parameters. A series of experiments was conducted with the rotational speed and the penetration rate held constant and the thrust and torque allowed to vary. The information collected from the experiments is used to determine the application of the drilling parameter measurements for identifying rock properties, fractures and bedding separations.