Search Documents

By Bernard Lewis

This report on the research and technical studies conducted by the Explosives Branch of the Bureau of Mines covers the 2-year period July 1, 1946, to June 30, 1948. A report for the fiscal year 1947 was omitted because of the large amount of work still in an unfinished state. The material presented herein is based largely upon more comprehensive reports prepared under the authorship of members of the branch staff.

Jan 1, 1949

By Norman] [Seldle

This report describes the development of a mine machinery training system from initial conception through a task and skill analysis, a training system analysis, implementation of a prototype system, and initial validation of the prototype system. The objectives of the training are to improve safety and productivity simultaneously via complete, thorough training. A task and skill analysts was executed for shuttle cars, continuous miners, cutters, loaders, face drills, tractors, and scoops. The prototype training system is for shuttle car operator training.

Jan 1, 1976

By William H. Lesser

Never before have mine managers in the anthracite region of Pennsylvania been so seriously concerned about the rising cost of pumping mine water. Many of them know that future pumping charges may affect their operating profits adversely to an extent that will make it necessary to abandon some mines. Increased pumping charges in the anthracite industry are currently comparable in importance with higher mining costs; in fact, profitable operation of some mines depends not only upon the cost of mining coal but also upon whether they can be kept free from water at reasonable cost. Pumping charges are relatively low during the early development of a mine, but they increase rapidly as development progresses. Numerous crop falls, strippings, and. abandoned adjacent properties contribute unfavorably to the volume of water produced during mining. The foregoing conditions and the existence of large underground pools below existing mining levels present water problems of such magnitude and cost that some mine owners cannot continue to operate profitably.

Jan 1, 1950

Real gross national product increased at a larger-than- expected annual rate of 8.3 percent in the first quarter of 1984, with both consumption and investment spending increasing significantly in real terms (table 1). Residential and nonresidential fixed investment increased at annual rates of 25.7 and 14.6 percent during the first quarter of 1984, and investment in nonresidential structures, which declined in 1983, also increased during the first quarter of 1984, nearly attaining its 1982 level. The annual level of personal savings increased $27.7 billion, while the personal savings rate (the ratio of personal savings to disposable income) increased to 5.8 percent during the first quarter. The increase in the personal savings rate comes as welcome news to analysts concerned over the flow of loanable funds to the private sector and the impact on interest rates in 1984 of increased private and Government demands. U.S. Minerals Industry Performance A major upswing in the performance of the metal mining sector occurred during the first quarter of 1984, with production increasing almost 11.2 percent from January to March, The recovery of the metal sector is also reflected in the performance of primary metal industry profits, which were positive during fourth quarter 1983 following seven consecutive quarterly losses (table 1). Two thousand nine hundred more metal mining production workers were employed in February 1984 than in February 1983.

Jan 1, 1984

By Lawrence J. Froisland

To aid in minimizing adverse environmental impacts of mining and mineral processing, the Bureau of Mines studied changes in soil characteristics in topsoil stockpiled during mining operations. Topsoil stockpiles in arid areas of New Mexico, Utah, and Wyoming were sampled over a 1- to 8-yr period to determine any changes in physical, chemical, or biological parameters in the top 15 ft of soil. Parameters examined in this study included soil moisture, pH, electrical conductivity, and cation exchange capacity; total nitrogen, organic carbon, carbon to nitrogen ratio, extractable potassium, and soluble phosphorus levels in the soil; general levels of bacteria activity in the soil; and productivity of the soil as measured by shoot yield in growth tests. Data were analyzed by multiple linear regression to determine possible effects of stockpile age and depth. Bacteria population counts, used as an indicator of goner l bacterial activity, was the only parameter found to be significantly correlated with stockpile age and depth at more than one site. Bacterial activity increased with depth at the two sites where it was measured. Activity increased with age at one site and decreased with age at the second. Significant changes in soil pH, electrical conductivity, and moisture were significantly correlated with stockpile age and depth at single sites. This study did not show significant, consistent deterioration in soil characteristics or growth yield of topsoil stored in stockpiles.

Jan 1, 1987

8186. Aquilina, C. Determinazioni relative di gravita eseguite nel 1939 (Relative Determinations of Gravity Made in 1939), Ric. Ingegn, Rome, vol. 10, 1942, pp, 6376. In 1939, the author made a survey of relative gravity in the Mediterranean-basin, 41° 35,5' to 41° 56.3' northern latitude and 0° 10,3' to 0° 28' longitude, referred to Mt. Mario. Ten stations were covered; 25 other stations had been occupied in the vicinity of Rome and in Albanian mountains during previous years. The new measurements revealed gravity anomalies ranging within the following limits: (1) With a free-air reduction, between + 29 and + 120 mgl., average + 60 mgl.; and (2) with a Bouguer reduction, between + 22 and + 87 mgl., average + 41.5 mgl. - V. S.

Jan 1, 1946

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if primary gas toxicities that evolve during the early (~300° C) and later (~.400° C) combustion stages of polyvinyl chloride and chlorinated brattices could be predicted by a smoke particle characteristic, which could be used as a simple and inexpensive test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 2500 and 1,0000 C, for 14 min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCl) and carbon monoxide (CO) concentrations, sample and furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and number concentration (no), and the product of the average smoke particle diameter and concentration (dgno)' Results show that the inverse of the smoke particle diameter-concentration (l/dgno) correlates directly with the primary gas toxicities evolved during both stages of combustion.

Jan 1, 1989

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety Factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By Joan Weinberg

Seasonally adjusted new factory orders for primary metals declined in January, February, and March, especially in the steel industry. The decline was part of an apparent slowdown for the entire manufacturing sector. Orders for all durable goods, including not only primary metals, but also clay, glass, and stone products, fabricated metal products, machinery, and transportation equipment, fell in January and February. In March, orders rose a slight 0.8%. According to the U.S. Department of Commerce, the downturns in durable goods orders in January and February were the first back-to-back declines in 3 years. They were largely attributed to a drop in orders for transportation equipment, mainly auto-mobiles and aircraft, while the small gain in March was due to a surge in aircraft orders. Higher interest rates may be partly responsible for the slowdown in durable goods orders over the past 3 months. The higher rates have also hit the construction industry--another major end-user of minerals. Construction of new homes and apartments fell by a seasonally adjusted annual rate of 5.4% in March, following a 12% decline in February.

Jan 1, 1989

By Jos. R. Guiteras

This paper describes the pumping operations at the Ajax, Cresson, and Vindicator dines in the Cripple Creek mining district of Colorado during the summer of 1936. At that time the three mines wore pumping 6,500 gallons of water per minute into the Roosevelt drainage tunnel. Cripple Creek is the most important gold district in the State; it has yielded gold valued at over $365,000,000. The mines engaged in pumping are among the largest producing properties in the district. ACKNOWLEDGMENTS The author wishes to acknowledge the friendly cooperation of mine officials at the properties visited. At the. Ajax mine information was courteously given by Clayton Kissel, mine superintendent, and his staff; R. Y. Roby contributed the drawings. For information on the Cresson mine, thanks are expressed to Al H. Bebee, mine superintendent, and his staff, especially to Guy Rorabaugh, master mechanic, and to engineer Carlton. At the Vindicator mine, J. S. Anderson; mine superintendent, and Robert Welch, master mechanic, assisted; the latter furnished most of the information about that mine. Acknowledgment is also made of the cooperation of M. H. Salsbury, engineer at the Portland mine, who supplied technical data on the Roosevelt drainage tunnel.

Jan 1, 1937

By W. R. Crank

[Rock bursts are phenomena associated with mining operations, particularly with deep mining, although they occur throughout a wide rump, of depth, from 600 feel downward. The intensity is usually in direct proportion to the depth, varying from a loosening and sloughing off to a violent rupture, giving rise to the term, "explosive rock." The more or less violent breaking of rock in mine working, tins been variously designated as " flaking," "pressure hoists," "strain bursts," "bumps," "quakes," and "air blasts," which indicate opinions as to cause and effect. The term "air blast" lots probably beat most widely used, and naturally so, as a more or less rapid movement of air often accompanying the more violent phenomena of rock failure. Furthermore, there is an implied if not definitely expressed degree of magnitude in the action designited by a given term and in the cause and character of the action. For example. flaking, pressure bursts, and quakes are terms ranged to indicate action of increasing magnitude; and pressure bursts, strain bursts. bumps, and quakes are ranged according to the cause and character of the action.]

Jan 1, 1929

By Gary A. Halvorson

Plots were established on regraded abandoned mine spoil to determine if nearby good quality spoil could be used in place of topsoil for the reclamation of these sites. Gypsum, calcium chloride, and power plant ash were also tested to determine the effectiveness of these materials in reclaiming these sites. Two sites were selected on which very little vegetation was growing on highly sodic spoil material. Gypsum, calcium chloride, and ash were added to the spoil at a rate designed to reduce the (sodium adsorption ratio) SAR in the surface 15 cm to 10 or less. The good quality spoil (replacement soil) was then laid on the swface at rates of 0, 5 or 15 cm of material. The plots were seeded to a mixture of smooth bromegrass (Bromus enennis Leyss.), crested wheatgrass (Agropyron desertorum (Fisch. Ex Link) Schult.) and alfalfa (Medicago sativa L.). The addition of 5 or 15 cm of replacement spoil significantly improved vegetative growth on these sites. Chemical treatments had no effect on vegetative growth. Weathered ash showed no adverse effects on plant growth or soil properties.

Jan 1, 1991

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

By J. D. Dixon

This Bureau of Mines report describes a technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. The technique is adapted for use with a nonlinear finite-element computer code, NONSAP, to obtain stabilization pressures for linear or nonlinear stress distributions in the rock media around the excavation. This analysis permits a point-wise calculation of active rock pressures that depend on the values of shear stress and strength along the excavation surface. The approach is applied to the solution of several sample problems. The results show that both the magnitude and the distribution of stabilizing confining pressures are significantly influenced by rock and joint strengths, joint orientation, and biaxial nature of the load field.

Jan 1, 1976

By Louis P. Domingues

As part of a study on high-temperature ceramic materials, the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of yttrium, lanthanum, and cerium were analyzed thermogravimetrically. The temperature ranged from room temperature to 1,500° C. Each salt was decomposed by heating at a rate of 2.5° C. per minute, and some of the salts were subjected to additional rates of 5° C. per minute or 10° C. per minute. The decomposition sequences have been identified, and the temperatures of formation of intermediate compounds and of the oxides have been determined. The minimum oxide formation temperature of a given lanthanum salt exceeds that for the similar salt of yttrium, and both exceed that for the same salt of cerium except for one cerium carbonate. Variation of the heating rate indicates a thermal lag in the materials and produces the shift of formation temperatures to higher values and loss of resolution in the weight-loss distribution as the heating rate increases.

Jan 1, 1962

By Nicholas R. Dixon

This report summarizes all work performed under Phases I, II and III of U.S. Bureau of Mines Contract H0387006, "Development of a Prototype Retrofit Noise Control Treatment for Jumbo Drills." The noise and vibration levels of four jumbo drills were characterized and a survey of percussive rock drill usage is reported. A Gardner-Denver DH 123 drill was chosen as a demonstration drill, and extensive noise diagnostic studies were performed. Noise control treatments were designed, developed and evaluated in a reverberant drill test facility. The treatments consisted of an integral enclosure/muffler for the drifter, vibration isolation of the drifter from the enclosure and feed, and a drill steel sheath. A 19 dBA reduction in overall sound power level was achieved with no loss in drilling rate. The prototype retrofit treatments were field tested in an aboveground mine and in a production section of an underground zinc mine. Long-term durability and operator acceptance of the enclosure/muffler treatment were excellent. Preliminary evaluation of the drill steel sheath was encouraging, although additional testing is required.

Jan 1, 1982

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

This is the seventh in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report covering 1,875 samples represents the products of 83 companies plus those from the Pacific coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. For the regular grade 985 samples consisting of 73 different brands are averaged. The premium grade consists of 489 samples of 40 different brands. The third grade has 401 samples averaged from 51 different brands. In this report the districts have been reduced to 21 by combining North and South Texas into one district. Fl Paso samples are reported with the South Rocky Mountain district, and Amarillo, Tex., has been included with the Middle Rocker Mountain district. In the present survey samples from Fort Smith, Ark., have been included in the Tulsa area, Indianapolis has been included in the St. Louis district. Cleveland represents the State of Ohio. Samples from Little Rock, Ark., and North Carolina have been included in the Memphis district. The Pittsburgh district includes samples only from this State and Wheeling, W. Va. The actual sampling points in each area are indicated an table 1.

Jan 1, 1939

This is the seventh in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1.935-36.3/ The present report covering 1,87 samples represents the products of 83 companies plus those from the Pacific coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. For the regular grade 985 samples consisting of 73 different brands are averaged. The premium grade consists of 489 samples of 40 different brands. The third grade has 401 samples averaged from 51 different brands. In this report the districts have been reduced to 21 by combining North and South Texas into one district. El Paso samples are reported with the South Rocky Mountain district, and. Amarillo, Tex., has teen included with the Middle Rocker Mountain district. In the present survey samples from Fort Smith, Ark., have been included in the Tulsa area, Indianapolis has been included in the St. Louis district. Cleveland represents the State of Ohio. Samples from Little Rock, Ark., and North Carolina have been included in the Memphis district. The Pittsburgh district includes samples only from this State and Wheeling, W. Va. The actual sampling points in each area are indicated on table 1.

Jan 1, 1939

By David L. Shuck

This report was prepared for the Bureau of Mines to describe the current methods of design, construction, and development of wells for in situ leaching of uranium. The discussion includes the alternatives for well design drilling equipment and fluids, grout formulation and emplacement, well integrity testing and repair, and well development and stimulation. Current practice in these areas was determined through interviews with eight operators of commercial scale in situ facilities and is also discussed. Based on this information plus the authors' experience, recommendations are made regarding well design, construction, and development tor in situ leaching.

Jan 1, 1982