Search Documents

By A. Hammel

This paper summarizes indigenous mining methods used to collectmetal ores in pre-colonial southern Africa, south of 15°S. These methods, for the purposes of discussion, are divided into sections inorder of increasing organizational complexity, from scavenging,which only required basic equipment and a relatively minimal division of labour, to underground mines, which necessitated complex planning to overcome obstacles such as the need for illumination and ventilation. Examples concerning the pre-colonial exploitation of iron, copper, tin, and gold have been taken from the archaeological literature. This review paper provides an introduction to the technology that was available to and used by miners in the past, illuminates some of the factors limiting their operations, and supports the claim to the indigenous nature of this activity

Jan 1, 2000

By C. Sensogut

The phenomenon of spontaneous combustion is one of the major hazards encountered in underground coal mines both from the safety aspects and on economic grounds. Every occurrence, however small, if not tackled effectively in the early stages can develop into open fire, or explosion of gas or coal dust. In terms of economy, even dealing with small incidents may be costly in terms of labour and materials, and in case of a sealing off of a district being necessitated, the loss of face equipment and sterilization of reserves is potentially great. Therefore, expense and effort in prevention and detection of such heating, together with a high state of readiness for dealing with likely event, is completely justified and may be considered as a sound investment. In order to achieve this investment, it may be worth to pinpoint the centre of the fire occurring due to autogenously heating which is supposed to be great assistance to inert it at a least cost and time. Therefore, it is the aim of this work to model the spontaneous combustion in the goaf.

Jan 1, 2002

By J. Szlazak, A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents the analysis of ventilation systems used in dead-end headings, while being drilled, in coal mines. Special emphasis is put on methane and dust hazard. Mathematical model for distribution of methane concentration in a heading is given as well. This model takes into consideration sources of methane emission and change in air flow rate due to leaks in a duct line. Solving equations presented in this article enabled giving dependencies describing distribution of concentration along the heading. On the basis of these dependencies there is a possibility of determining places with higher methane concentration and ways of combating this hazard. Determining the distribution of methane concentration in dead-end headings ventilated by a separate ventilation system is of great importance as far as work safety conditions are concerned. The information obtained may be of use when finding proper places for installing methane sensors. Three kinds of separate ventilation systems were distinguished: forcing, exhaust and overlap. The development in construction of fans and spare parts of a duct line enables using both forcing and exhaust ventilation systems in headings developed by continuous miners, with length above 1000 m, in the conditions of methane, temperature and health-detriment dust hazards.

Jan 1, 2003

This paper addresses the methodology of introducing risk into the development of mine plans for open pit mines. Recommendations are put forward for achieving a risk balance between mineral resource estimates and slope design. A design process identifying criteria for different stages of planning is presented. Business risk is separated from geological/geotechnical risk and procedures to address these within the development of mine plans are suggested. It is concluded that a formal design process improves communication between key decision makers and adds value to shareholders, investment.

Jan 1, 1997

The paper reviews the results emanating from an experiment conducted in Bochum?Germany in which various international rope inspection authorities were requested to assess the conditions of a corroded rope sample as well as a rope sample containing internal fatigue breaks. Both samples were of the multi-layer low rotation construction.

Jan 1, 2000

By S. M. Bradshaw

The principles of microwave heating are discussed with reference to dielectric properties, heating phenomena and microwave equipment. Microwave regeneration of granular activated carbon for the carbon-in-pulp process is examined on a laboratory scale, with special attention being given to highlight the problem areas and specific considerations related to microwave heating. Results indicate that microwave regeneration of carbon with 40% moisture on a wet basis by heating to 650°C with steam addition regenerates the carbon to virgin carbon activity levels but with a higher abrasion resistance. A preliminary economic assessment showed that the capital cost for 120 kg/h microwave unit would be R540 000 with an annual operating cost of R 320/t carbon. These figures yield a return on investment of 12%. The aim of this paper is to provide an introduction to microwave heating and to illustrate its application to the microwave regeneration of granular activated carbon for the carbon-in-pulp (CIP) process.

Jan 1, 1998

By B. Kenny

The aim of this paper is to provide an overview of existing forms of subcontracting in the South African mining industry. A descriptive framework is developed to understand different subcontracting arrangements. We argue that, in order to do so, it is important to distinguish between labour broking and gang subcontracting. Data resulting from a research project (including an analysis of historical sources, interviews with contractors and focus group interviews with mineworkers) is presented to highlight the implications of changing formations of subcontracting for the South African mining industry in the late 1990s. Apart from the subcontracting of ?traditional? functions, such as shaft sinking, access development, catering and hostel maintenance, contractors are now used in ?core? mining activities. In some instances, whole shafts are ?outsourced? to outside agencies. It is argued that certain of the subcontracting arrangements have serious implications for the ability of the mining industry to improve health and safety standards. Some of the practices can potentially result in conflict between different categories of workers, and, as a result, instability in the industry.

Jan 1, 1999

By M. J. Nicol

The kinetics of the dissolution of colloidal silver in aerated cyanide solutions has been investigated with the aim of developing a relatively rapid and convenient method for monitoring the ?leaching power? of solutions typically used in the cyanidation process. Experimental results obtained are consistent with an electro-chemical model, in which the mixed potential is set up in the active region of the polarization curve for the anodic dissolution of silver, giving rise to a rate of dissolution which is controlled by the rate of mass transport of either cyanide or oxygen to the surface of the silver. The rate of dissolution of colloidal silver was found to respond to variations in the reactant concentrations in a similar manner to gold (and silver) in a typical free-milling ore. The use of this technique for the monitoring and control of the cyanide leach process is discussed.

Jan 1, 1998

The 102nd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 18th August, 1999. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows and Past Presidents D.D. Howat Life Fellows O. Deane, J.S. van Zijl Fellow A.A. Hejja Retired Fellows A.L. Forder, C.B. Parker, A.C. Petersen, F.W.J. Ross Members J.S. Stanko, D.H. Gray Retired Member P.K. Bredell Retired Associate I.S. van Eyssen In memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1999

By R. Pickering

The purpose of this paper is to explore the application of technology to stoping systems. Technology, because for the past 100 years the South African narrow reef mining industry has battled to control working costs in a labour-intensive industry. Stoping systems, because it is the stoping method and methodology which is at the heart of the mining system. Introduce a more efficient stoping system and the mining system will look after itself. The technology applied to stoping over the past 100 years can be categorized as follows: ?The introduction of pneumatic rockdrills early this century, the cumbersome rig mounted units being replaced by smaller, lighter hand-held units which were then made easier to use with the addition of an air leg ?Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s ?Hydraulic props as a support method arrived in the1960s ?Some people argue that tungsten carbide inserts were equally important. There have been a number of attempts to introduce different technologies into stoping, the most recent being trackless equipment. Where the stoping layout suits the technology it has been successful. There have been too many instances where a technology has been installed because it is fashionable. At the end of the day the outcome from change in the stoping systems has to be safer and more profitable mining systems. It is the contention of the author that change is only likely to be effective if it is supported by the introduction and application of appropriate technology.

Jan 1, 1999

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By X. Yu

Although many investigations of the deformation behaviour of rocks have been carried out, most of them are carried out in compression. In all rock engineering practice it is usually assumed that the deformation of rocks in tension is the same as that in compression. However, data from numerous researchers have shown that this assumption is not correct for some rocks. A new loading frame for testing rocks in compression and direct tension has recently been developed by the authors, with the capacity to conduct both compression and tensile tests on the same rock sample. The results obtained show that the ratios between the average Young?s modulus in compression (ECA) and in direct tension (ETA) are 1, 1.16, 2 and 6 respectively in four rock types tested. For Poisson?s ratios, analogous relations were obtained. It was observed that, in all cases, the tangent Young?s modulus intension reduces with an increase in the applied tensile stress, while the behaviour of Poisson?s ratio is similar, but shows greater variability. The difference between the Young?s modulus of rocks in tension and that in compression could lead, large errors in calculating induced stresses around underground openings, as well as in determining the Brazilian tensile strength of rocks. This may have a significant influence in rock engineering and therefore more investigation is necessary into the tensile deformation behaviour of rocks and its influence.

Jan 1, 2005

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 483 to 496 for the year ended 30 June 2004. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with statements of South African Auditing Standards. Those standards require that we plan and perform the audit to obtain reasonable assurance that the financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, ?assessing the accounting principles used and significant estimates made by management, and ?evaluating the overall financial statement presentation. We believe that our audit provides a reasonable basis for our opinion. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2004 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice. Auditors 30 July 2004 Council?s approval of the annual financial statements The annual financial statements for the year ended 30 June 2004 set out on pages 483 to 496 were approved by the Council on 30 July 2004 and are signed on its behalf by:

Jan 1, 2004

By S. Luyckx

This paper reports hardness and abrasive wear resistance test results from a wide range of WC-Co alloys, varying in cobalt content as well as WC grain size. The results show that the abrasive wear resistance increases with increasing hardness and that the rate of increase is higher for larger WC grain sizes. The increase in abrasive wear resistance was found to be parabolic up to a critical hardness value and exponential above that value. The transition from parabolic to exponential behaviour was found to occur at the same contiguity value for all grain sizes, which suggests that at that contiguity value the WC skeleton becomes continuous in all WC-Co alloys.

Jan 1, 2004

By J. R. G. Williamson

The Mining Division of Iscor, an integrated minerals and metals company, has recently completed a feasibility study for the establishment of a new heavy minerals mine and smelter in the Richards Bay area of KwaZulu-Natal, South Africa. The mine will produce a heavy mineral concentrate containing ilmenite, zircon, rutile and leucoxene which will be beneficiated at a central processing complex close to Empangeni. The ilmenite will be smelted to produce high-grade titania slag and pig iron for export. The ancient dune containing the mineral deposit is located some distance inland of the coastal dunes, and the sands contain a high proportion of extremely fine material which must be extracted ahead of the gravity separation process. Of the 56 million tonnes to be mined annually over the ten-year life of the mine approximately 23,4%?a total of 13,1 million tonnes of minus 45 micron residue fines?will have to be disposed of in a containment facility. The origin of the fine material is from the weathering of amphibole minerals. The remaining coarse sands will be returned to the mined area to re-create the original dune configuration. A number of options for the disposal of the residue fines have been examined and specialised laboratory tests undertaken to determine the deposition behaviour of the fines. The final solution involved the use of a ?sub-aerial? technique for deposition of fine material in a disposal facility. The resulting arrangement will adequately meet technical and environmental criteria. Upon closure after 10 years of operation, the surface of the disposal facility will be returned to sugar cane cultivation The paper refers to the various options considered and describes the problems associated with competent disposal of the residue fines and the development details of the final disposal facility.

Jan 1, 1997

By A. V. Peake

Continuous Mining presents an opportunity to extract reef in the stope ?continuously? by integrating the drill and blast activity using propellants or low energy charges. To date, the majority of effort spent on Continuous Mining systems has focused on developing an effective rock breaking process (micro breaking process), and to some extent, eliminating fumes and dust. The perceived benefits of applying low energy charges have been identified as: ?Concentrated mining yielding face advances of 40 to 60 m per month ?Lower stoping widths through better-controlled breaking ?Increase in the advance per blast ?Increase in labour productivity ?The potential to mine reefs where specific conditions make conventional mining uneconomic e.g. reefs with shales in the immediate hangingwall. However, the ability to successfully use low energy charges to create a ?Continuous or Semi-Continuous? mining method is dependent on overcoming the following challenges. ?Improving reliability of rock breaking. This is dependent upon achieving:? Improved drilling accuracy, and? Successful stemming or gas confinement, particularly in fractured rock ?Reducing gas and dust levels ?Reducing high costs. Through the research carried out in Future Mine, many different low energy rock breaking methods and systems were investigated. Whilst detailed results cannot be published here, the guidelines for overcoming low energy rock breaking challenges are discussed.

Jan 1, 2003

By K. -H. Lux, Z. Hou

ABSTRACT: It is well known in underground mining and waste disposal that the development of excavation damaged zones (EDZ), and thus, hydraulic pathways, is closely related to the excess in the corresponding damage boundary (= long-term strength) of the rock mass and the resulting damage. By integrating short-term and long-term strength, dilatancy, damage and healing into the newly extended Hou/Lux constitutive model for rock salt, it is possible to treat the tertiary creep, to identify the EDZ around underground facilities and to predict the time-dependent development of the EDZ in rock salt. Under in-situ conditions, the EDZ of a 37-year-old drift at the Sondershausen salt mine and the EDZ around a drift dam in rock salt are numerically examined. The numerical analysis gives satisfactory results. RÉSUMÉ: Dans les exploitations minières et le stockage souterrain des déchets, le développement des zones endommagées et fracturées (EDZ – excavation damaged zone), créant des chemins préférentiels pour écoulement, est étroitement lié au contexte géotechnique et à la méthode d’excavation. En intégrant la résistance court et long terme, la dilatance, l’endommagement et le colmatage, le nouveau modèle rhéologique Hou/Lux pour le sel gemme est capable de traiter le fluage tertiaire, d’évaluer l’extension de l’EDZ et de prédire l’évolution de EDZ dans temps autour des ouvrages creusés dans le sel gemme. L’EDZ d’une galerie datée de 37 ans dans la mine de sel de Sondershausen et les EDZ autour de barrage des galeries dans un sel gemme ont été modélisées. Les résultats numériques fournissent des résultats satisfaisants. ZUSAMENFASSUNG: Bekanntlich ist die Entstehung von Auflockerungszonen und damit hydraulischen Wegsamkeiten in der unmittelbaren Umgebung um bergmännische Hohlräume mit der Überschreitung der entsprechenden Schädigungsgrenze eng verbunden. Unter Berücksichtigung der Bruchfestigkeit, Schädigungsgrenze, Dilatanz, Schädigung und Verheilung kann das Stoffmodell Hou/Lux das Verhalten des tertiären Kriechens beschreiben, die Auflockerungszone im Salzgebirge ermitteln und ihre zeitabhängige Ausdehnung vorausberechnen. Mit diesem Stoffmodell werden die Auflockerungszonen einer 37jährigen Strecke in der Salzgrube Sondershausen und die Auflockerungszonen um ein exemplarisches Abdichtungsbauwerk im Salzgebirge numerisch untersucht. Dabei werden zufriedenstellende Berechnungsergebnisse erzielt.

Jan 1, 2003

Changes in reductant and energy inputs which are required to adjust the slag composition in an ilmenite smelter to a higher or lower FeO content are calculated. The calculated changes are based on the assumption that solidification equilibrium with the freeze lining constrains the slag composition to follow a eutectic groove in the TiO2-FeO-TiO1.5phase diagram. Calculated equilibrium conditions along the eutectic groove are presented, and form the basis of the calculations. The inputs of energy and carbon need to deviate strongly from the steady-state values to adjust the slag composition. The inputs required at any given time depend on the desired rate of change of the slag composition, and the current slag composition. The steady-state relationship of a change in energy input of 5 kWh corresponding to a 1 kg change in carbon input also holds for the changed inputs during transient changes in FeO content. Keywords: Ilmenite smelting, freeze lining, solidification, eutectic

Jan 1, 2003

By C. Dixon

The Abandoned Mine by C.C. Woollacott A heap of rocks marks the abandoned mine. The veld's unpitying silence lies around. Those broken stone?a mute and mournful sign Of human enterprise with failure crowned. Time with the slow hands, shall form the scene anew, Repair the gashes in the wounded soil, And cover up the last remaining clue To a poor useless record of men's toil. And this, the mound they built when hopes were high Shall be a grave, where those hopes buried lie. Outline This paper will consider the implications of the mine closure provisions set out in the new Mineral and Petroleum Resources Development Act and draft regulations. A comparison will be made with the existing provisions in the Minerals Act and the mine closure policy of the Department of Minerals and Energy (DME). The paper will consider whether the new provisions have the potential for improving performance as regards mine closure. It will investigate the financial provisions requirements and the implications of these provisions for mines. It will consider the requirements for a social and labour plan and consider the implications of this for mine closure and its funding. It will analyse the provisions relating to the transfer of environmental liabilities to third parties and consider the implications of this in the case of closing mines and non-closing mines. Finally it will consider the issue of residual legal liability of a mining company once a closure certificate has been issued.

Jan 1, 2003

By S. Jiansheng, H. Nakayama, D. Lu, A. Wang

ABSTRACT: New techniques and methods for 3D geo-mechanical model test are presented in this paper. The new model material NIOS with high density and low cost; the so-called DPSS (Discrete Principal Stress Surface) loading concept, the loading and monitoring system for the generation of the 3D initial stress field of the model test, also the special techniques and apparatuses for modelling the excavation of caverns located deep inside the model material, are developed and introduced. By adopting those new techniques, a very large 3D geo-mechanical model test with high comparability for a newly designed underground powerhouse has been successfully fulfilled. Key Words: 3D model test, underground group caverns, excavation process modeling. ZUSAMMENFASSUNG: Neue Techniken und Methoden für 3D geomechanischen Modellversuch wurden in diesem Artikel vorgestellt. Ein neues Modellmaterial mit hocher Dichte und niedrigem Preis, ein sogenanntes DPSS (Discrete principal stress surface) Ladenkonzept, ein Laden- und Überwachungssystem für die Erzeugung des 3D primären Spannungsfelds und überdies spezielle Techniken und Maschinen für das Ausbruch der tief in dem Versuchsmodell liegenden Kaverne wurden entwickelt. Bei Anwendungen dieser neuen entwickelten Techniken wurde ein sehr großer 3D Modellversuch mit großem Maßstab für ein geplantes unterirdisches Kraftwerk erfolgreich durchgeführt. Stichworte: 3D Modellversuch, unterirdischen Gruppekaverne, Ausbruchsmodellierung Résumé: le test de modèl de Nouvelles techniques et méthodes pour la géo-mécanique 3D est figuré dans ce papier. Le nouveau modèle de matériels NIOS avec la haute densité et le coût bas; la conception proposée de chargement DPSS (Discrete Principal Stress Surface), le système de chargement et de moniteur pour la génération de champs de stress initial du test de modèle, ainsi que les techniques et appareils spéciaux pour modeler les excavations de cavernes profondément localisées dans l’intérieur du matériel de modèle, sont développés et introduits. A travers l’adoptation de ces nouveaux techniques, le test de modèle de la géo-mécanique très large 3D avec la haute comparabilité pour actualiser une nouvelle étude de la centrale électrique sous-terraine a déjà accompli avec succès. Mots de clé: test de modèle 3D, groupes de cavernes sous-terraines, processus de modèle d’excavation

Jan 1, 2003