Search Documents

By P. J. Lloyd

Society is fully justified in its concern about the environment, but that concern may, at present, be too uncritical It is, for instance, essential to establish that there is a valid environmental impact, and that there is truly a causal link between a human activity and an observed shift in environmental conditions. In establishing these, it inessential to recognize that scientific proof offers consistency, but that it can never provide completeness. Thus, no amount of scientific endeavour can ever prove that mitigation of the effects of human activity will be perfect. Society normally expresses its concern through legislation. The existing legislation in South Africa is reviewed, and it is found that [>legislation regarding water is probably too stringent to be effective, >legislation regarding air and land use is probably too lax, >all the environmental legislation is too fragmented to be efficient, and the Department of Environmental Affairs is hamstrung by inter-departmental rivalry. ] It is accordingly concluded that, if means are to be found for ensuring adequate mitigation of environmental impact in the face of ongoing economic development, it is necessary to establish a Judicial Commission on Environmental Affairs advised by, but given greater powers than, the departments currently active in environmental maters. This Commission should be charged with creating, perhaps over a decade, a body of legislation that would guide development while protecting the environment in its widest sense.

Jan 1, 1994

The First International Symposium on Seismicity in Mines, organized by the South African National Group on Rock Mechanics in collaboration with the South African Institute of Mining and Metallurgy, was held in Randburg (near Johannesburg) from 13th to 17th September, 1982. It was the first attempt to provide an international forum for the consideration of seismic problems specifically affecting mines or associated with mining. Numerical mathematics The South African Society for Numerical Mathematics and the Computer Science Department of the University of Natal are organizing the Ninth Symposium on Numerical Mathematics to be held in Durban from 18th to 20th July, 1983.

Jan 1, 1983

By R. K. Brummer

The support of stopes and tunnels in South African gold mines subject to rockburst damage requires special attention. The interaction of a seismic wave with either a stope or a tunnel is subject to a number of variables, namely the distance from the source of the event, the ground velocity, the orientation of the excavation with respect to the direction of the seismic wave, and the geology and fracturing around the excavation. This paper discusses these factors in relation to the support requirements in stopes and tunnels. The need for the integration of hydraulic props with stope support and the use of yielding anchors for tunnel support are emphasized.

Jan 1, 1988

By P. A. Laxen, P. J. van Staden

In situ leaching tests with thiourea as the lixiviant were caried out in two worked-out stopes at the No. 6 shaft at Rand Leases Gold Mining Company. Dissolution rates of 0,9 and 0,7 9 of gold per week per 100 m2 of footwal area were achieved. A major disadvantage of the method seems to be the slow rate of dissolution of the gold, which is probably caused by poor contact and slow mass transfer between the lixiviant and the gold surfaces. Under full-scale application, the loss of lixiviant by leakage could also be a very important factor. Furthermore, the oxidation products of thiourea may 'poison' the activated carbon that is used for the recovery of the gold. The method may therefore be economically viable only in stopes that contain high values of residual gold.

Jan 1, 1989

By M. Kirsten, W. H. Botha, M. H. Fox, J. A. Moolman, A. J. Lathwood

Water is a valuable and in many areas a scarce resource. Governmental legislation regulates the environmental impact of water usage and wastewater disposal through the issue of licenses. These requirements mean that hydrometallurgical refineries must ensure that water consumption and water disposal is managed on a continuous basis in order to prevent the repeal of their operating license. Water balances are often overlooked during the design of a hydrometallurgical refinery. Recent changes in environmental legislation have forced both design engineers and operational management to review water use and disposal within these processes. Unlike concentrators where water can easily be recovered by recycling from tailing dams, water introduced into hydrometallurgical refineries becomes contaminated with soluble metals and thus requires pre-treatment prior to disposal. This paper discusses the various concerns that need to be considered during design and operation of hydrometallurgical refineries with respect to the water balance.

Jan 1, 2007

By S. Selmer-Olsen

New trends and developments in the production of ferro-silicon, ferro-manganese and ferro-chrome alloys are discussed, with emphasis on the general trend to the adoption of large production units. Problems which arise, both of a metallurgical and an electrical nature, due to the use of large electric furnaces, are outlined with specific reference to the limitations imposed by the power carrying capacity of Soderberg electrodes, the furnace resistance and the furnace reactance. The implications of combining high resistance within the furnace with good metallurgical operating conditions are illustrated by considering the production of ferro-silicon and ferro-manganese. The possibility of replacing electric furnaces used for ferro-manganese production, by large low shaft blast furnaces using oxygen enriched blast, is mentioned. The continued use of small electric arc furnaces for ferro-chrome production is also mentioned, and is ascribed to lack of ore suitable for treatment in large furnaces. Agglomeration of chromite ores appears to be a possible answer to this problem.

By P. C. Schutte, J. R. Smith

The objective of ergonomics is to enhance the effectiveness and efficiency with which human tasks are carried out. Furthermore, the objective is to improve desirable human values. This can be achieved by enhancing safety, reducing fatigue and stress, increasing comfort, increasing job satisfaction, having greater user acceptance and thereby improving the quality of life. Mechanization has influenced the prevalence of injury, mainly due to the application of human physical effort as the power source. With mechanization, the operator’s function is now essentially one of control rather than being an energy source, however the risk of injury has not diminished. Mechanization in itself has introduced inefficiencies, health risks and physiological stress. The major objectives of ergonomics are discussed through examples of acceptable and less successful implementation of ergonomics within mechanized mining. The influence of the machine system on the human is addressed and practical solutions to improve and optimize the interaction of the human and the machine are outlined. Furthermore, practical examples of control and display integration, anthropometric and biomechanic influences on design, orientation, posture and stereotypes are used to accentuate the advantages of the application of sound ergonomics principles to the specialised area of mechanized mining.

Sep 1, 2001

By J. P. McDonald, P. L. Mattison, J. M. W. Mackenzie

A variety of processing problems in the hydrometallurgical extraction of uranium in the U.S.A. are contrasted with those in South Africa. In U.S. plants, for example, problems are often encountered in the separation of vanadium, molybdenum, and uranium, and in the contamination of the circuit with organic acids. South African plants often experience problems with dissolved silica in the feed, clarification of feeds, and problems associated with synthetic polyelectrolytes. Individual situations are examined, along with the analytical techniques that assist in solving specific problems. Successful approaches that have been applied to mechanical and chemical problems in' uranium solvent-extraction plants are discussed.

Jan 1, 1981

By C. W. Siyasiya

Process and steel chemistry differences in hot rolled Al-killed low carbon strip steel between the hot charge route (HCR) as practised in a compact strip production (CSP) plant and the conventional cold charge route (CCR) have been studied. This was done with reference to differences in reheating practice, hot rolling practice and steel chemistry through emphasis on the effects of solubility and reprecipitation of AlN in the two process/product combinations and its effect on ferrite grain size development. An earlier modelling study on the evolution of the austenite grain size in both of the above hot rolling processes has also now been extended to include an estimate of the possible effects of retained strain after the last finishing pass on the ferrite grain size. As part of this study the equilibrium solubility trends of AlN in a number of boron-free low carbon Al-killed strip steels with low and high sulphur content from the two respective processes was investigated by the thermoelectric power (TEP) technique and differences in the effects through the derived solubility equation of Log[Al][N]=2.6?9710/T at typical slab reheating temperatures was demonstrated. Ferrite grain size modelling using the significantly lower Ar3 transformation temperatures generally found in hot rolled low carbon strip steel produced in the CSP plant using the HCR compared well to the larger grain size produced in the conventional CCR strip rolling plant. Keywords: austenite grain size modelling; thermoelectric power(TEP); compact strip production (CSP); cold charge route (CCR);ferrite grain size

Jan 1, 2008

By R. J. Mason

The paper discusses the claim that the remains of mines in Southern Africa date from ancient times, rather than from a more modern period. The evidence indicates that these mines were excavated by Iron Age Black people, who moved into South Africa from about A.D. 100 onwards. Details are given of the finds made in 1981 in an investigation of the remains of copper mines in the Dwarsberg, which probably date from the nineteenth century.

Jan 1, 1982

By L. A. Cornish, J. W. van der Merwe

"The hydrofluoric acid (HF) industry in South Africa uses normalized mild steel (SA 516 Gr 70) for the storage and distribution of its technical-grade product (70% HF). The technical-grade acid is split from the anhydrous hydrogen fluoride (AHF) product during distillation just after HF is produced, in a stainless-steel-lined kiln, from the reaction of calcium fluoride (CaF2) with sulphuric acid (H2SO4). Uniform corrosion of the storage tanks is mitigated during commissioning by contacting the steel with 70% HF. A corrosive reaction takes place (2H+ + 2F- + Fe - H2 + FeF2) to form scale inside the tank which diminishes the attack of the steel by fresh HF, thus prolonging the service life expectancy of the vessels. This iron fluoride scale in the vessel grows continually, resulting in corrosion of the vessels continuing at a predictable rate (approx.0.5 mm/a) since the first commissioning of the tanks at Necsa in 1993. In early 2012, an increase in the average corrosion rate of the tanks to 3 mm/a measured at and below the liquid band in the storage vessels was noted. Three months later the corrosion rate had increased to 30 mm/a, just before the first leak from the tank was detected. The tanks were decommissioned shortly afterwards and an investigation revealed that the rapid corrosion was due to the presence of increased levels (>50 ppm) of nitric acid (HNO3) in the tanks, which attacked the fluoride layer protecting the steel.The oxidation characteristics of high concentrations of HNO3 with low concentrations of HF on stainless steel surface treatment are well documented. The effects of low levels of nitric acid on the corrosion of steels in sulphuric acid are also known, but no suitable published data currently exists on corrosion by high HF concentrations with low HNO3 concentrations. Establishing the rate and mechanism of corrosion by HNO3 (0.1 to 1%) in 70% HF is currently a high priority for the HF industry in South Africa and will become increasingly important in the near future due to depleting fluorite reserves and cheaper, but less efficient, processes producing H2SO4 with higher impurity levels, which were not anticipated in the original plant design. The aim of this study is to simulate the corrosion conditions in the plant on a laboratory scale in order to establish the corrosion characteristics of the steels used in the HF plant, which are increasingly exposed to the HNO3 impurities that tend to concentrate in the final technical-grade HF acid product."

Jan 1, 2016

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental Sampling Error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centered on the sampling constant K and the exponent, alpha (a), of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis (DSA) method and the heterogeneity test (HT) method purport to provide such a constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine and Lily mine. Two of these mines (Mponengand Kloof) are typical Witwatersrand-type gold mines, while the third is an Archaean-type, shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appears to be too small and does not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis, are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2009

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By R. Van Deventer

The BIOX® process was developed for the biological pre-treatment of refractory gold ores and concentrates ahead of conventional cyanide leach gold recovery. Rights to the process are currently with BIOMIN Technologies SA, a subsidiary of Gold Fields Limited. There are currently eight operating installations worldwide employing the process on a commercial scale. EKATO is a company specializing in developing new or optimizing existing mixing applications. EKATO has acquired a vast amount of expertise in agitation over its 75 year history. In a joint research project the reactors of the BIOX® process were characterized from the aspect of their mixing performance. BIOMIN is constantly testing new mixing solutions and reviewing potential vendors to increase the efficiency of the BIOX® process. EKATO?s intention was to qualify as an approved vendor for supplying agitation equipment to the BIOX® process. A two step approach was planned: In phase one of the project EKATO would develop an alternative agitation solution to the established option, exhibiting at least similar performance levels. In phase two potential possibilities to improve the overall design would be developed. This paper focuses on phase one and addresses the systematic approach applied by EKATO in characterizing the mixing processes. Mixing tasks were assessed individually applying basic theory and scale-up and -down rules to the individual tasks. Testing with model systems was done at the EKATO technology center in Schopfheim, Germany, on scales of 50 liters and 1 m³. The results showed that the ISOJET-B impeller design showed promising performance under BIOX® reactor conditions. Scale-up with the ISOJET-B was done in order to apply it in the 21 m³ live volume test reactor at Fairview mine in South Africa. At Fairview tests were performed using model systems and eventually under real plant conditions with BIOX® slurries. The results were a success and confirmed that the scale-up factors determined during the testing at EKATO?s technology center could be substantiated in the ?model scale? 25 m³ reactor. Testing under the actual process conditions showed that all design parameters were within the desired range to be considered an excellent leaching performance. This successful joint development shows the importance of a close cooperation of technology licensors or end-users and equipment suppliers. It is vital for understanding all factors influencing the mixing performance of processes. Exercises such as this will provide equipment suppliers and plant operators more confidence in managing further scale ups at ever larger engineered plants.

Jan 1, 2009

By M. M. Makhofane

Anhydrous zirconium tetrafluoride can be used as a precursor for the manufacturing of nuclear-grade zirconium metal. This can be done by fluorinating plasma-dissociated zircon with ammonium bifluoride in a batch reactor. This paper describes the batch process. It was proved that anhydrous zirconium tetrafluoride can be manufactured by this route as confirmed by X-ray diffraction. The process shows potential for scaling up to the kilogram scale and possibly the tonnage scale.

Jan 1, 2012

1. New books Specialty steels and hard materials, edited by N. R. Comins and J. B. Clark. Oxford, Pergamon, 1983.482 pp. Hardcover £55.50. Papers presented at an international conference on advances in flow measurement techniques, edited by H. S. Stephens and B. Jarvis. BHRA Fluid Engineering (Cranfield, Bedford, MK43 OAJ, England), 1982. £36. Papers presented at Fourth European Conference on Mixing, edited by H. S. Stephens and D. Goodes. BHRA Fluid Engineering (Cranfield, Bedford, MK43 OAJ, England), 1982. £36. Papers presented at an international conference on hydrocyclones, edited by H. S. Stephens and G. Priestley. BHRA Fluid Engineering (Cranfield, Bedford, MK43, OAJ, England), 1982. 248 pp. £27. Controlled atmospheres for heat treatment, by R. Nemenyi. Oxford, Pergamon, 1983. 225 pp. Hardcover 20, flexicover £7.50. Electrochemical techniques in corrosion testing and research, edited by J. S. Scully. Oxford, Pergamon, 1983. 150 pp. Flexicover £9.45 2. Book reviews Off highway truck haulage, by the Newman Combined Group. Parkvine (Victoria), Australasian Institute of Mining and Metanurgy, 1982. Reviewer: B. J. Vorster Elsevier's mineral and rock table, compiled by P. Lof. Reviewer: A. Wedepohl Field geologists' manual, by B. A. Berkman. Monograph Series No. 9, Australasian Institute of Mining and Metanurgy, 1982.295 pp. Reviewer: R. A. G. Cuipers 3. Mintek reports Report M56 A computer programme for the evaluation of process routes in the production of ferrochromium. Report M61 An atomic-absorption programme for the Apple 11 Plus computer. Report M63 A general-purpose data logger. Report M65 A preliminary survey of the corrosivity of water in gold mines. Report M66 A review of corrosion inhibitors: theory and practice. Report M67 The determination of total cyanide in solutions containing uranium and gold. Report M68 The suitability of Doppler flowmeters for use in the minerals-processing industry. Report M70 The preparation and certification of two reference materials of South African manganese ore. Report M78 A n evaluation of the Leeds laboratory-scale flotation cell. Report M79 The determination, by X-ray-fluorescence spectrometry, of gold and uranium on resin. Report M80 The installation and commissioning of a Siemens SRS200 sequential X-ray-fluorescence spectrometer. Report M81 The application of the inductively coupled plasma system to the simultaneous determination of precious metals. Open-pit and strip mines The South African Institute of Mining and Metallurgy and the Mining Alumni Society of the University of Pretoria are organizing an International Conference on The Planning and Operation of Open Pit and Strip Mines in Pretoria from 9th to 13th April, 1984. Other Institutes co-sponsoring the Conference are The Canadian Institute of Mining and Metallurgy, The Institution of Mining and Metallurgy, and The Society of Mining Engineers of AIME.

Jan 1, 1983

By V. Moodley

Strict implementation of International Standards for representative sampling of coal is difficult for routine monitoring, due to time, technical, and economic constraints. A large percentage of the total sampling variance arises from errors accumulated during the earliest stages of sample collection. Modified procedures on the precision of the final result leads to controversies between the sellers and customers for coal. Manual collection of coal samples violates the principle of correct sampling, that all fragments must have an equiprobable chance of being in the sample. In addition, manual size reduction of large numbers of samples is time consuming and involves human errors. A coal quality management procedure in alignment with the relevant ISO standards that describes the sampling protocol has been implemented, and current sampling and laboratory analysis of coal from base load mines (mines situated at the mouth of the power station) are well established. For import coal, sampling is performed during unloading by auto-mechanical sampling (AMS). Due to logistical and safety issues associated with multiple suppliers, Eskom opted for the coal to be sampled at source on a pre-certification basis. Online analysers provide a fast, accurate, real-time method of determining the total moisture and elemental composition of coal and is important to the coal industry for pricing, quality control, and reduction of SO2 emissions. Elemental analyses include S, Si, Al, Fe, Ca, Na, Mg, Mn, Ti, K and Cl. Measurement of S is dictated by the control of SO2 emissions from coal-fired power plants. Elements such as Na and Cl have adverse effects on boilers, causing fouling and slagging. Available online elemental analyser technologies include prompt gamma neutron activation analyses (PGNAA), recommended for major element determination, and pulsed fast and thermal neutron analysis(PFTNA), that is capable of measuring the major and minor chemical elements contained in coal. These systems utilize nuclear reactions to produce characteristic gamma rays that are used for identifying various chemical elements. By acquiring the gamma rays in three different time windows, there is a significant reduction of the background as compared with the spectra taken with a radio isotopic source.

Jan 1, 2009

By L. von Ketelhodt

Dual energy X-ray transmission (DE-XRT) sorting is a recent development in the range of sensor-based sorting technologies available today. DE-XRT is particularly suitable for dry coarse coal beneficiation in the size range -120 mm +12 mm. In this paper, we describe the technology and show the results of a number of test runs conducted on different types of coal from the USA and South Africa. The results have shown that DE-XRT is an effective technology not only for deshaling of coal and removing pyritic sulphur but also for separating coal and torbanite. The use of dry deshaling methods will be more important as water availability becomes a greater concern. DE-XRT is one such technology which will be incorporated in future dry coal processing plants.

Jan 1, 2010

By D. F. Malan

Considerable practical knowledge and effective use of empirical evidence is required in the design of tunnel support systems. In many instances, it is unclear how individual support elements interact with fractured rock and which elements of the support system are critical in controlling and containing the movement of material proximate to the excavation. The present paper outlines a displacement discontinuity approach that allows the coupling of surface constraints, in the form of liner or mesh material, to an explicit representation of time-dependent rock discontinuity creep movements. The method is illustrated for a simple square-shaped tunnel profile in which the fracture zone is mobilized by an imposed stress field. A crucial aspect of the model is the computational treatment of the coupling between the liner material and there presentation of the fractured rock mass. This allows the response of the liner material to be assessed quantitatively in terms of the possible reduction of movement in the rock mass. The importance of installing the liner timeously after the excavation is formed is illustrated in a specific example. A number of computational difficulties in simulating liner-rock interaction mechanisms are identified.

Jan 1, 2008

By K. Arnold

AngloGold Ashanti has been proactive in the field of energy management for many years. AngloGold Ashanti is a signatory to South Africa?s National Energy Accord of 2005 calling for a15% reduction in energy consumption by 2015 for the mining sector. This target also supported our internal targets that were already set. AngloGold Ashanti?s seven South African mines consume on average 440 MW. Due to the dynamics of gold mines, and the large numbers of relatively small energy efficiency initiatives and awareness campaigns made measurement and verification of energy efficiency very difficult at a macro level since some initiatives could get lost in the fluctuating load profile. This paper will discuss the methodology and process followed to quantify the impacts of the combined energy efficiency initiatives at macro level. It will quantify the energy efficiency impacts in megawatt-hours (MWh), financial, and equivalent carbon emissions (CO2e) reduction with reference to our baseline year, 2004, for the Vaal River and West Wits mine clusters.

Jan 1, 2009