Search Documents

By L. A. Jagger

The world?s second largest producer of platinum, Impala Platinum Ltd, approved two new twin shaft projects at the end of September 2004, Nos. 16 and 20 Shafts. Both shaft projects are stand-alone entities and are being sunk from surface. Previously Impala had embarked on a strategy of extending the life of its third generation shafts by means declines. No. 16 Shaft is the first of a new fourth generation shaft complex, while No. 20 Shaft is the last of the third generation type shafts in the so-called shallow to intermediate mining zone. This paper details the basic designs of each project and covers the initial implementation. Although both projects are twin shaft systems, the access methods from the shafts to the reef horizon differ. Initiatives implemented to speed up the projects are also briefly covered.

Jan 1, 2006

By C. Kliem

Geological, tectonic, geochemical and geophysical data were utilized for the mineral resource assessment of the Biga Peninsula in NW Turkey. During the deductive phase of the project multivariate statistical methods were applied to accentuate characteristic parameters which sufficiently describe the different types of Pb - Zn mineralization. The parameters most likely to be indicative of mineral occurrences were determined. In the following prognostic phase these parameters were further statistically treated to determine favourability indexes for the occurrence of a deposit within each cell of the training area. Preliminary results of probabilistic, univariate and multivariate methods are presented.

Jan 1, 1987

By R. Kosmicki

Wet end components of centrifugal slurry pumps used in the hydraulic transport of solids are subject to substantial erosive wear. Accurate prediction of the casing wear rate and location for a particular duty is beneficial for correct pump selection and design, maintenance planning, and elimination of emergency shutdowns. CFD multiphase simulation using the Eulerian-Eulerian approach is being applied successfully to determine the velocity fields and solids concentration in the centrifugal pump, allowing for accurate predictions of casing wear patterns resulting from sliding abrasive wear. Simulation results for various single domain and multi-domain (multistage) multiphase simulations are discussed. Emphasis is placed on results from a 3-dimensional, multi-stage transient, multiphase simulation and comparison to field data.

Jan 1, 2007

By F. T. Cawood

This article offers a personal and independent view on the threats to the sustainability of the South African minerals industry. It argues that if the six identified threats of insufficient spending on research and development, general standard of education, nationalization, inadequate infrastructure, Aids prevalence and labour inefficiency are not acted upon as a matter of urgency, the future of the mining industry, along with its important contribution to the economy, is at risk.

Jan 1, 2011

By E. Cetin

Orebodies that contain more than one economically important mineral are generally evaluated by parametric cut-off grades. This approach often leads to mis-valuation of mineral deposits because cut-off grades are not based on the grades of each individual mineral and, because of the parametric formulation, are only indirectly related to the individual grade distributions. The only realistic approach is a formulation that accounts separately for each component mineral. The grid search method can be used as a means of multi-mineral cut-off grade optimization in this context. This paper describes the use of the grid search method in cut-off grade optimization for multi-mineral deposits. The authors introduce the general concepts of the method and formulate its application to cut-off grade optimization; they describe a software implementation of the method that can accommodate cut-off grade optimization for mineral deposits that contain up to three economic minerals. Keywords cut-off grade, optimization, grid search, multi-mineral deposits.

Aug 1, 2013

The variety and sources of sampling errors have been studied since the late 1800s, but the pioneering work of Pierre Gy in the 1950s provided insights into sampling as an error generating process. Total sampling variance is a measure of the total sampling error, but disaggregating the variance into its component parts is problematical. Ten sources of error and error generating processes have been identified, some of which can be eliminated through rigorous application of the principle of correct sampling. Others can only be minimized but never eliminated. Three principal questions relating to the appropriate mass of a sample, the fragment size of the sample and the size of the associated error are addressed. These questions relate principally to the Fundamental Error (FE), the only error that can be estimated before the sampling event. Aspects of constitutional and distributional heterogeneity are examined, as are the essential components of Gy?s formula including the shape factor (?), the granulometric factor (g), the mineralogical composition factor (c), and the liberation factor, l. Applications of Gy?s equation to the problems of sampling in the minerals industry are explained using real-life examples. The approach to sampling taken by Pierre Gy provides an excellent inferential relationship between the mass of material to be sampled, the size of the fragments being sampled, and the relative variance of the sampling error. It also provides solutions for three of the main problems associated with the Theory of Sampling.

Jan 1, 2007

By L. Marais, S. Denoon-Stevens, J. Cloete

"Historically, mining companies worldwide provided housing and developed towns to accommodate their employees. At the end of the 1980s this approach became less prevalent and attempts were made to mitigate the effects of mine development and mine closure on communities living near the mines. Permanent settlement in mining towns urgently needed to be minimized. Since the advent of democracy, South African policy has moved in the opposite direction, shifting the emphasis to creating integrated communities and encouraging home ownership. Despite this policy shift, however, mines continue to influence local housing conditions. One direct outcome has been the development of informal settlements. We surveyed 260 informal settlement households in Postmasburg, a small and remotely located town in the Northern Cape Province of South Africa. We found that because they employ contract workers and thus arouse expectations of employment, the mines here contribute extensively to the development of informal settlements. But local factors also contribute, and the functional role of informal settlements as a form of housing that supports mobility should not be underestimated. We also found that both municipal and mining company policies for informal settlements were inadequate. Finally, we found that low-income informal settlers not associated with mine employment suffered the highest levels of social disruption.IntroductionA mine generates demand for labour, which in turn generates demand for housing. When settlements spring up near a mine this often means poor housing conditions. In South Africa in the 1960s and 1970s mining companies invested heavily in company towns or mining settlements, but they have become increasingly hesitant to do so, for three reasons. First, declining resource prices in the mid-1980s and the 1990s compelled them to focus on core business interests and reduce the costs of peripheral activities such as housing (Bryceson and MacKinnon, 2013); second, at the turn of the 20th century they were often accused of taking over the role of local government (IIED, 2002) and consequently became hesitant to invest in developing mining towns; and third, changing labour regimes also curbed their investment in such towns (Haslam McKenzie, 2010). Increasingly, the companies began to endorse block-roster shifts, and outsourcing also became more common in the early 1990s. Block-roster shifts in Australia (together with improved technology) have meant that miners do not need to settle near the mines but can fly in and fly out and have their urban houses as their stable homes. This has had serious negative implications for housing in remote towns in Australia, particularly worker camps, large-scale renting out of available accommodation, and ‘hot-bedding’."

Oct 1, 2018

By J. N. Van der Merwe

Following the Coalbrook disaster in 1960, research into coal pillar strength resulted in the adoption of the concept of a safety factor for the design of stable pillars in South African coal mining. At the time when the original statistical analysis was performed by Salamon and Munro in the early 1960s, 27 cases of failed pillar workings were considered suitable for inclusion in the database of failed pillars. Pillar failure did not stop after the introduction of the safety factor formula by Salamon and Munro (1967). In the ensuing years, pillars that were created before the application of the formula deteriorated and later failed, as did ones that were created after the introduction of the formula. This means that over time, the database of failed pillar cases increased in size, allowing ever more reliable analyses to be performed. The number of failed cases in the database had grown from the original 27 in the 1960s to 86 by 2011. All the failed cases are contained in the updated database. The database of stable pillars, which is also used in the derivation of strength formulae, has now been extended from 125 to 337 cases. The new database of intact pillar cases is more complete as it bridges the time gap between the Salamon and Munro (1967) and the Van der Merwe (2006) databases. The original requirements for inclusion into the database were satisfied in the compilation of this latest collection. The characteristics of the original database of intact pillars did not change in a meaningful way. The mining depth and pillar dimensions of the new database are largely as they were in the original database. Time-related trends with regard to pillar dimensions and depth of mining could not be found, indicating that the geometrical parameters of coal mining in South Africa have not changed meaningfully in approximately a century of mining. The characteristics of cases in the updated database of failed pillars does not differ substantially from the one published by Van der Merwe (2006). The same difference between that database and the original Salamon and Munro database, namely that the average safety factor of the failed cases had increased dramatically, from 1.0 to 1.5, is still apparent. This may be due to the inclusion of more failures from specific areas that exhibit a disproportionate number of failures at higher safety factors. These areas are the Vaal Basin, Klip River, and Free State coalfields. The new database confirms yet again that there is no correlation between the safety factors of failed pillars and their time of failure. The safety factor on its own is thus not a reliable predictor of longterm stability of pillars. Keywords coal pillar, stable pillar cases, pillar collapse, pillar data base.

Nov 1, 2013

By N. Brown

Australian mining companies are actively exploring for and developing mineral deposits throughout the world with interests in emerging markets such as Africa, Asia and South America. It is important to understand emerging market risk as this will affect the willingness of mining companies and financial institutions to invest in a country, especially with reference to their key asset, the mining licence or operating/concession agreement. Mining companies looking to develop new projects in emerging markets have different risk profiles than projects in countries such as Australia and Canada. Examples of key risks faced in emerging markets include: 1. political - expropriation, nationalisation, contract frustration, currency inconvertibility, war, terrorism, strikes, riots and civil commotion; and 2. legal - mining legislation, arbitration and dispute resolution, trade agreements. There is a problem in the difference in risk perceptions between mining companies, financial institutions and insurers. This can cause different stakeholders to carry out different evaluations of the risks faced by a project, resulting in confusion about the risk margin attached to any project. In a time where resource nationalisation and energy security are prompting governments to become more involved in the mining sector we run through some recent examples of mining companies that have had problems due to the key risks highlighted earlier. Importance of carrying out the right due diligence to replace perceptions with reality: ? early identification of risks - detailed due diligence on emerging market risks that may arise will help with their identification and mitigation, ? make use of companies that can help identify risks and suggest solutions, ? control the cost of financing - risk margin applied to a project ? finance loan will be influenced by the risks faced, and ? risk management and using political risk insurance. There are plenty of opportunities in emerging markets but it is important to recognise the associated risks. Detailed due diligence at an early stage will provide long-term benefits.

Jan 1, 2007

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidizing agent. This work shows how the performance of pressure leaching circuits may be improved by optimizing the configuration of autoclaves and the heat removal method. The objective was achieved by creating an autoclave model that combines mass balances, energy balances, and population balances. A base case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity increase options include circuits in which the additional autoclave is added in parallel, in series, and in series with thickening between the two autoclaves. The copper extraction, productivity, and cooling requirements for these options are compared. The series circuit with interstage thickening has the highest extraction and productivity; however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water, and flash recycling. The flash recycle option results in the highest copper extraction, and the quench water option the lowest copper extraction. IntroductionBackgroundCopper sulphide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work.In the pressure leaching process, sulphide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidizing agent, usually oxygen, is required to oxidize sulphide ions to sulphate ions. The oxidation of sulphur to sulphate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2016

By J. T. M. Amphlett, C. A. Sharrad, M. D. Ogden, R. I. Foster

"A renewed interest in nuclear power around the world in order to reduce greenhouse gas emissions is going to increase demand for uranium as fuel. This will result in more uranium being mined, which will in turn increase associated environmental pressures, such as fresh water use. A move to lower quality waters containing impurities such as chloride would help alleviate these pressures. In this work, we determined the uptake characteristics of weakly basic anion exchange resin Ps-EDA towards uranium from saline solutions in a dynamic flow column. Breakthrough curves were produced, with suppression of uptake being observed for chloride concentrations above 5 g L-1. Calculated resin saturation capacities at zero and 5 g L-1 chloride are comparable with literature values for strong-base anion exchange resins, and exceed those published for weak-base resins up to 20 g L-1 chloride. Data has been fitted to multiple breakthrough models, with the modified dose-response model most effectively predicting uranium recovery. The results show that the ethylenediamine functionality could be suitable for use in future uranium processing flow sheets where a high-saline lixiviant is used. IntroductionIon exchange (IX) is a key technology in the uranium mining industry and is well established for the extraction of uranium from both acidic and alkaline leach liquors (Edwards and Oliver, 2000). It was first employed in 1952 at the West Rand mine in South Africa (Ford, 1993; Taylor, 2016). H2SO4 and Na2CO3 are the most commonly employed lixiviants used to solubilize uranium in acidic and alkaline leach conditions respectively. The chemistry of these systems causes uranium to form anionic sulphate or carbonate complexes, which can be taken advantage of by anion exchange resins.Another major technology for the extraction and purification of uranium from leach liquors is solvent extraction (SX). This technique involves the extraction of uranium from the aqueous phase into an immiscible organic layer. Although this is a commonly used method, there are major drawbacks to it, including the use of large volumes of flammable solvents, solvent loss, phase disengagement, third phase formation, and the production of problematic degradation products (Veliscek-Carolan, 2016). These problems can be circumvented through the use of IX resins."

Dec 1, 2018

By t. Knezicek

Tuzla Coal Basin in Bosnia and Herzegovina is the largest coal area in the State. Regional mining industry sensed the need for mining machinery database development in order to achieve easier planning purposes and equipment selection for open cast mines in Tuzla Coal Basin. Several databases for mining machinery used on the bituminous deposits, i.e. on brown coal and lignite mines, were developed at the Faculty of Mining, Geology and Civil Engineering, Tuzla. System Development Method was used as the approach to the database development, generating relational structure of database. First database was established for trucks and was presented as simple table, drawn and filled on the paper sheet. In the next phase, data were stored in spreadsheet type software (Quattro Pro and Excel). Lately developed database is Bucket Wheel Excavator database designed in MS Access. Two concepts, spreadsheet and Access, were integrated into one large database, enabling manipulation of hundreds of data at one place. Required adaptations of existing database in MS Access, enables Access to be used as an integration resource. Database is designed to reserve free memory for input data for mining equipment not considered so far, such as spreaders, crushers, belt conveyors, tripper cars, etc. New, integrated database, at this stage, can be imported to any type of commercial or individual software where needed. Mining machinery integrated database for open cast mine operations is under going testing in a State company, Coal Mines Tuzla. Keywords: Tuzla Coal Basin, machinery database, SDM, relational database

Jan 1, 2003

This paper summarises some observations regarding the way SAG and AG mills work based on the last ten years of pilot plant operation, grinding circuit design and operational reviews for various projects in Australia and overseas. The main purpose is to promote discussion on key factors influencing breakage in a SAG mill. The focus of the paper is on two questions: ? How do mill lifters and liners really work and have an effect on grinding? ? How does the mill charge composition impact on grinding performance? The focus of the paper is on observations of mill behaviour in both pilot plant trials and plant operation, particularly on Cadia ore. DEM, by others, and JKSimMet modelling of SAG mill performance have greatly assisted in forming the ideas expressed in the paper and both are valuable tools in developing our understanding of the comminution process. Put in the `extreme' form the major observations and conclusions expressed in this paper are that: ? the main purpose of mill lifters is to reduce mill liner wear and not to promote rock breakage; ? the often promoted theory that balls impacting the ?toe of the charge? is a dominant form of breakage is incorrect; and ? fines production in a SAG mill is primarily a function of the rock load mass, with a secondary dependence on ball load for any given circuit configuration.

Jan 1, 2007

By I. Zemanek, A. Rozsypal

Mrazovka tunnel was excavated under one building whose subsurface space was not possible to reinforce against additional settlements induced by digging. In the presented contribution the risk analysis, warning levels and results of deformation measurements are described. Lespace souterrain d‘un des bâtiments sous lequel le tunnel Mrazovka a été creusé n‘a pu être renforcée contre l‘affaissement supplémentaire provoqué par l‘emplacement du tunnel. Le matériel présenté décrit l‘analyse des risques, le niveau des limites et les résultats des mesures des déformations. Der Untergrund eines der Gebäude, unter dem der Tunnel "Mrazovka" ausgeschachtet wurde, war es nicht möglich, gegen nachträgliches Setzen zu versteifen, hervorgerufen durch die Untertunnelung. Im vorliegenden Beitrag sind Gefahrenanalyse, Grenzwerte und Ergebnisse von Deformationsmessungen beschrieben.

Jan 1, 2003

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions. Keywords value driver trees, production constraints, throughput analysis, capacity analysis, TOC (Theory of Constraints), activity interdependencies, unit cost reduction.

Oct 1, 2013

By C. C. Johnson

In the fourteen years that Rössing Uranium Limited has been in production, the metallurgical operations and controls on the leaching plant have evolved through four basic stages. Initially, the emphasis was placed on the achievement of consistent plant operation by overcoming severe startup difficulties. The second stage involved the attainment of the design operating targets, and also the commissioning of the ferric-leaching reactors in order to achieve a ferric ion concentration of more than 3,0 g/l. Improvements in control then became the priority, with the emphasis on consistently achieving the target concentrations of ferric ions, total iron, and terminal acidity. The latest phase has concentrated on the optimization of costs by means of adjustments to the historically established operating parameters in order to achieve large savings on consumables while maintaining the leaching efficiencies. Apart from the obvious incentive of reducing costs in an inflationary economy and a depressed uranium market, impetus for this work was given by a change in the type of ore from the open pit, which has the effect of reducing the extraction efficiency while increasing the consumption of consumable materials. These problems and their solutions are discussed in detail, and the importance to cost-effective optimization of an accurate, up-to-date cost-reporting structure is stressed.

Jan 1, 1990

By D. B. deur Mostert

This paper was presented at the Coloquium on Management Techniques in the Mining and Metallurgical Industry, which was organized by The South African Institute of Mining and Metallurgy and held in Pretoria during June 1988. The author asks whether technical audits are of any use to management. Technical auditing he defines as an evaluation undertaken by an outsider of whether a technical activity is being carried out correctly. After examining the types of technical auditing, and its prerequisites and procedures, he describes its application in regard to quality, and to production processes and their adequacy. He then answers his question by saying that, not only are technical audits very useful, but they form an essential element in the provision of quality products. In addition, they give management the opportunity of testing whether the activities of the organization are being conducted correctly. This is their most important function in that they alert management to areas of potential growth, modernization, and innovation. However, the use to which technical auditing is put remains the key to its value; that is, its value depends on the positive action that each manager takes as the result of a technical audit.

Jan 1, 1989

By D. Gregurek

The complexity of metallurgical processes in the non-ferrous metals industry. especially changes in the process conditions in combination with a diversity of metal processing furnaces, requires a precise knowledge of the system for the selection of refractory products. However, particular importance is still focused on the specific refractory consumption being as low as possible. The addition of recycling material with a high amount of impurities and the increase of low-grade ore concentrates used in the base-metals industry also entails a significant change of slag chemistries, process temperatures, etc., which influence the performance of already approved linings. This acknowledgement of process changes with decreased brick lifetimes provided the motivation for RHI AG to develop high-performance refractory bricks especially for non-ferrous metals applications. The internal laboratory tests with fayalitic slag showed very promising results compared with our approved magnesia-chromite bricks for this application. In order to identify suitable refractory products and to improve the life of the refractory lining, innovative product development has to be undertaken. In addition, the practical corrosion testing methods and facilities available within the RHI Technology Center, such as the induction furnace and the rotary kiln test equipment, allows the best possible understanding of brick wear at a laboratory scale. Based on the results of the test work, the optimal refractory solution can be recommended for a field trial at the customer?s site.

Jan 1, 2012

By H. D. Mtegha

Mining is important to the economies of both Tanzania and Namibia. Recently, both nations revised their national mineral policies to ensure future economic benefit. The main difference in the mineral policy-formulation processes followed by the two countries is identified as the degree and timing of stakeholder involvement during the articulation process. In the case of Namibia, the stakeholders were involved from the start in identifying issues and in suggesting policy solutions. In contrast, the Tanzanian process involved stakeholders after a framework had been developed by a task team. The Tanzanian emphasis was on attracting foreign investment into a traditionally state enterprise system of mineral investment and development. One can argue that the policies developed met the initial requirements, and both are, therefore successful, despite the different processes of policy formulation that were used. However, several fundamental questions arise as a result of the two approaches. This paper attempts to answer these questions by providing a comparison of the processes used for developing and formulating the mineral policies of Tanzania and Namibia. It concludes that the Namibian consultative process is perhaps more sustainable in the long-term because of its wider public support. Time will tell which of these policy-formulation processes provides a basis for sustainable economic growth for developing mineral economies.

Jan 1, 2010

By J. Levin, I. J. Corrans

Wet high-intensity magnetic separation (WHIMS) for the concentration of gold and uranium was tested on many Witwatersrand cyanidation residues, and on some ores and flotation tailings. The results varied, but many indicated recoveries of over 60 per cent of the gold and uranium. The main source of loss is the inefficiency of WHIMS for material of smaller particle size than 20fLm. The recoveries in the continuous tests were lower than those in the batch tests. The continuous tests indicated an operational difficulty that could be experienced in practice, namely the tendency for wood chips and ferromagnetic particles to block the matrix of the separator. It was decided that a solution to the problem lies in the modification of the separator to allow continuous removal of the matrix for cleaning. A system has been developed for this purpose and is being demonstrated on a pilot-plant scale. Promising results were obtained in tests on a process that combines a coarse grind, gravity concentration, and WHIMS. In the gravity-concentration step, considerable recoveries, generally over SO per cent, of high-grade pyrite. were obtained, together with high recoveries of gold and moderate, but possibly important, recoveries of uranium. A simple model describing the operation of the WHIMS machine in terms of the operating parameters is described. This should reduce the amount of empirical test work required for the optimization of operating conditions and should provide a basis for scale-up calculations. The economics of the WHIMS process is discussed.

Jan 1, 1979