Search Documents

At the Annual General Meeting of the Chamber of Mines of South Africa, held in Johannesburg on 29th June, 1982, the following leading members of the mining industry were elected to office for the 1982-1983 term: Mr W. W. Malan President Mr C. T. Fenton Vice-President Mr G. Y. Nisbet Vice President William Wouter Malan was born in Springs on 7th November, 1928, and was educated at the Springs High School and the University of the Witwatersrand, where he obtained a B.8c degree in mining engineering. Diamond Mines. Mr Nisbet became a consulting engineer of the Anglo American Corporation in 1972, and a deputy managing director of the Gold Division in 1974. George Young Kisbet was born in Benoni in 1923 and was educated at Pretoria Boys High and the University of the Witwatersrand. Mintek reports Report 2010D A process for the recovery of rare-earth oxides from monazite. (First published 16th March, 1979). Report 2073D A preliminary investigation of the concentration process at Ucar Minerals Corporation. (First published 19th September, 1980). Report 2092D The recovery of pyrite from gold ore by gravity separation. (First published 28th November, 1980). Report M13 Factors affecting the production of fines during the screening and handling of highcarbon ferromanganese.

Jan 1, 1982

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

An evaluation was made of the wear and performance characteristics of liter bars, and the cost-life effectiveness of backing materials for rotary-mil liners. In a large run-of-mine mil in which the liter bars were mounted on grid liners of austenitic manganese steel (AMS), the liners had an average life that was five to six times that of equivalent unprotected liners. For a single mil, this is equivalent to annual savings in the cost of materials of up to R320 000, and to a downtime of 100 hours. Of the five materials tested in a large pebble mil grinding quartzitic ore, AMS grids and 'white iron' blocks performed best on a cost-life basis, with possibly improved performance from a real white cast iron. (The 'white iron' was shown by microstructural analysis to contain flake raphite and pearlite, being in reality a grey cast iron.) The high-chromium white iron had by far the longest predicted life, with mild steel a surprising second. Rubber was shown to last well in this type of mil. The wear rates of liners change during their lifetimes. The protective effect of liter bars was clearly illustrated by the reduction of over 40 per cent in the wear rates of the liners when the lifter bars were renewed to a height of 80 mm from a fully worn height of 35 mm.

Jan 1, 1991

By N. Coulson, P. Ledwaba

"The University of the Witwatersrand presents an accredited four-course training programme for community relations practitioners (CRPs). Between May 2013 and October 2014 six courses were facilitated for 145 participants, of whom 82% were from sub-Saharan Africa, 62% worked in mining, and 58% worked directly with communities. Thematic analysis of the comments of course participants collected during course exercises found that there were a set of coherent drivers for resilient companycommunity relationships, but that the restrainers to resilient relationships were often context-specific and dominated by politics. CRPs reported facing as many difficulties in the internal company environment as in the external environment. These findings for CRPs in Africa resonate with those worldwide.InroductionMuch has changed in how the extractive industry responds to social and community issues. There has been a growing prioritization of community-related issues within the extractive industry globally (Kemp, 2010; Tatar, n.d.). According to Kemp (2010) this can be attributed partly to escalating pressure from local-level stakeholders to push mining companies to take greater responsibility for the social, economic, and environmental impacts of mining. Securing and maintaining the social licence to operate is ranked fourth in terms of the top risks facing the mining and metals industry in 2016, up one place from 2015 (Ernst & Young, 2016).Conflicts between local communities and large-scale mining companies arise because of the social, environmental, and economic impacts of mining. Worldwide, large-scale mining companies have a poor reputation amongst communities, including those in Africa (Gilberthorpe and Banks, 2012; Kemp and Owen, 2013a; van Wyk, n.d.). For mining companies, conflicts for whatever reason, result in loss of productivity, lost opportunities, lost time, and adverse impacts on reputation (International Council on Mining and Metals, 2015). Conflicts also have a significant financial impact on mining operations (Franks et al., 2014). Davis and Franks (2014), estimated that US$10 000–50 000 is lost each day when a project is delayed during the exploration phase, and about US$20 million per week when in operation. Today these costs could be expected to be higher due to increasing input costs."

Jan 1, 2017

Dr T. F. Muller (Honorary President): "Mr President, gentlemen. May I congratulate the Institute on its 75th birthday, and your President on his comprehensive review of the Institute's 75 years. It is an interesting commentary on the affairs of the Institute that your President should refer to a speech made by a founder member 25 years ago on the occasion of your 50th Anniversary and then say there is no need to repeat what was given there, but that he would confine his remarks to bringing the Institute's history up to date. To me this suggests a remarkable continuity of thought and ideals-a welcome island of stability in an ever-changing world. One can somehow picture another future President, perhaps one of the younger and tougher members here today, doing the same thing in 25 years when you celebrate your centenary-and again someone doing the same in the year 2094 when your Institute is 200 years old! I hope they will recognise their debt to the early pioneers of the Institute gathered here today. In any event, this review of the fine achievements of the past 75 years is certain of an honoured place in the annals of the society. Here is a record of the onward march of technology in South Africa and a tribute to a long line of mining engineers, of chemists, metallurgists and geologists who made a greater contribution to the well-being and the prosperity of South Africans than South Africans generally are aware. Your Institute started off as a 'gold and cyanide club', peopled largely by chemists and metallurgists who made a signal contribution to the industry from the earliest times. Despite the addition to their ranks of ever-growing numbers of mining engineers, the metallurgist members have continued to make notable contributions. One recalls, for example, the manner in which they rose to the occasion to resolve the problems associated with the establishment of the uranium industry in this country. The creation of a major industry based on the existence of low grade uranium ores in the conglomerate reefs of our low grade goldfields is a classic example of the manner in which a new large industry can be rapidly created through the combined endeavours of all concerned. I noted with pleasure your remark, Mr President, that members of the Institute would like to keep up to date with recent progress in nuclear fuel matters and that members should be given the opportunity to study developments in their journal. I am sure that the National Institute of Metallurgy which conducts fuel research on behalf of the Atomic Energy Board and of the Uranium industry, and NUFCOR, which co-ordinates the uranium research programme, would be glad to co-operate if invited by the Institute to make periodical contributions to its journal. You have referred to the building up of our research organization and its dynamic approach to mining problems. I understand that the expenditure of the mineral industries on research exceeds one-third of the entire research expenditure of the private sector. South Africa is in the forefront of mining development and the focus of world attention is on the achievements of our scientists and mining engineers. We can look forward to continued advances in mining technology based on their vision and expertise. I share your disappointment, Mr President, that the Base Metals Division has ceased to exist; and that there is a resultant dearth of papers offered to the Institute on these important sections of mining and metallurgy. We are seeing some remarkable developments in the mining and beneficiation of base minerals, and it is in this area that I see the greatest potential for future expansion. If we can grasp the opportunities

By S. P. Molefe

Mr Chairman, members of the executive committee, the sub-committee, distinguished speakers at this opening plenary session, delegates, affiliates, ladies and gentlemen. It is with pleasure that I have been called upon today to make these opening remarks and officially welcome you al at this auspicious assembly, the Fifteenth Congress of the Council of Mining and Metallurgical Institutions. Not only am I pleased to open the proceedings at this plenary session but for me to do so at Sun City in the North-West Province makes me doubly pleased. It is my wish that al delegates and their companions will enjoy the activities that are planned throughout the Congress and leave here with minds refreshed and stimulated by the technical sessions and memories enriched by being in such a unique and truly delightful setting as exists here at Sun City. The mix of delegates present reflects CMMI activities in many countries throughout the world-Australia, Japan, China, United Kingdom and South Africa among others. When it comes to mining and related activities, South Africa has a place at the top, a dominant role in platinum, gold, chromium, vanadium, dimension stone, coal and so forth, and here in the North-West Province we can proudly declare that some 25 per cent of the revenue from minerals in South Africa, namely R47 billion come from this area. Furthermore, we lead in the production of platinum group metals with 94 per cent of South Africa's total sales and thus hold first place in the world, 46 per cent of dimension stone sales, 32 per cent of chromate and 25 per cent of gold sales.

Jan 1, 1994

Book review Burkin, A. R. (ed.) . Leaching and reduction in hydrometallurgy. London, Institution of Mining and Metallurgy, 1975. £10. hydroxide pyritearsenopyrite NIM reports Report no. 845 A n electron-microprobe study of the nickel distribution in a serpentinite from Volspruit, Potgietersrus. (22nd Oct., 1969; re-issued Dec. 1975). Report no. 1546 Pilot-plant smelting campaign on iron ores from Tete. (22nd May, 1973; re-issued Jun. 1976). Report no. 1557 Cost estimates for the production of pig iron in the Tete district of Mocambique. (18th Jun., 1973; re-issued Jun. 1976). Report no. 1600 Dilute-acid leaching of slag from Tete ore. (20th Nov., 1973; re-issued Jun. 1976). Report no. 1602 The roasting of Tete slag for the extraction of vanadium. (20th Nov., 1973; re-issued Jun. 1976). Report no. 1635 Magnetic separation tests on Tete slag and ore. (30th Apr., 1974; re-issued Jun. 1976). Report no. 1671 Pyrometallurgical retreatment of a slag for the recovery of vanadium. (11th Oct., 1974; re-issued Jun. 1976). Report no. 1785 Some thermodynamic aspects of systems relevant to the flotation of sphalerite. Report no. 1808 Spectrophotometric determination (with pyrocatechol violet as chromogenic agent) of aluminium in zirconium metal and in the residue from anodesludges. Report no. 1813 The economic potential of some pegmatites from the Kenhardt area in relation to the trace-element content of their border zones. Report no. 1817 The rapid determination by X -ray-fluorescence spectrometry of tungsten in tungsten ores and concentrates. Report no. 1820 The thermodynamics of the formation of chlorocomplexes of iron (III), cobalt (II), iron (II), manganese (II), and copper (II) in erchlorate medium.

Jan 8, 1976

By T. Gibson

It is generally accepted that South African coal mines have gone through the mechanization of most of its underground mines, and while there certainly were a lot of productivity improvements, the lack of visibility on these machines operating underground still leave vast areas for improvement. The average actual cutting time still remains very low, in the 30 per cent area, which leaves significant improvement possible. Currently all analysis is carried out using hand-written reports. Unfortunately this is subjective and often inaccurate because of human interpretation. In addition in order to avoid costly component failure, a monitoring system is required to warn of eminent failures and condition monitoring. The challenge faced was to supply and install a system that was ‘Open’ and could be retrofitted to existing machines in operation because of the current standard of communication links to the underground sections. In addition it was intended to use, existing ‘off the shelf’ software and hardware and adapting this for the harsh underground mining conditions wherever possible in order to reduce costs. As development occurred, as with all technology, doors opened to other opportunities such as, remote access data logging and Internet based reporting. We focused on the Voest Alpine Bergtechnik (VA) range of continuous miners, as need arose to achieve the desired cost improvements because of the strategy of service contracts the subsidiary company, Voest Alpine Mining & Tunnelling (VAMT) offer the mining industry in South Africa. This paper describes a data logging system that has been installed on various continuous miners that provides data in real time, on line, and that could be expanded to any electrically supplied underground mobile or stationary mining machine.

Sep 1, 2001

By D. G. Krige

By use of models based on the South African gold-mining industry, analyses are made of the effects of changes in the mining tax structure on the .State's tax income from potential new mines; also on the percentage of such mines likely. to be proceeded with. The percentage is affected by the correlation between changes in taxation and in the flotation pay limits !or new mines. It is shown that the State stands to gain both directly and indirectly from raising the level of the capital allowance and from its extension to all mines; and that the reduced taxation resulting from a lowering of the discriminatory high tax formula for the gold mines, would, in respect of potential new mines, be compensated for by a significant increase in the percentage of such mines that would be proceeded with.

Jan 1, 1979

By K. I. Afewu, L. C. Woollacott

The design of in-pulp adsorption vessels in the gold industry has, for the most part, been seen as a problem involving the suspension of fine particles o ore in a slurry. The need for the vessel to be designed as a mass-transfer contactor has received insufficient attention. The current series of papers addresses this need The previous paper considered the question of the scale dependence of the film transfer coefficient. This paper examines the mixing considerations that are relevant. A review of the literature and an examination of a limited set of data provide some insight into the mixing conditions needed for the dispersion of the particles of adsorbent. The mixing requirements for the suspension of the ore particles are also considered, and conclusions are drawn in regard to the design of mechanically agitated vessels for gold in-pulp adsorption circuits.

Jan 1, 1995

PREFACE During the past year, the Council of the SAIMM undertook a major strategic-planning exercise to review all its current activities, and to redefine its scope and objectives in the light of changing circumstances. The following are the four main concerns that prompted Council to take stock of the situation. (1) Over the past five years, the SAIMM has become heavily involved in a variety of new activities. (There are many examples, of which the expansion in book publications and the establishment of physical metallurgy as a third major discipline with its own colloquia and schools are perhaps the most important.) While these new activities have considerably broadened the SAIMM's scope, they have resulted in a significant increase in the day-to-day workload of the President, Office Bearers, and Council members, and of the secretarial staff based at Kelvin House.

Jan 1, 1986

Book Review Sampling in the mineral and metallurgical processing industries. London, Institution of Mining and Metallurgy, 1973. 65 pp. illus. £5. The seven papers presented at a special meeting of the Institution of Mining and Metallurgy held in London in July, 1973, have been brought together under the above title.

Jan 11, 1973

By Pamela Binstead

The Institute's ninetieth anniversary was celebrated in grand style with a banquet and dance in the ballroom of the Carlton Hotel in Johannesburg, on 22nd March. Some six hundred and thirty members and guests filled the room to capacity, and many remained to enjoy the festivities until well past midnight.

Jan 1, 1985

By J. H. Viljoen, J. F. Morrison, C. H. Wyndham

SYNOPSIS Heart rates, oral temperatures, shovels/min and number of 3/4 ton cars/hour trammed over distances of up to 350 ft were measured in samples of 6-10 miners, engaged in tram-shovelling, at 76°, 84°, 86°, and 89°F wet bulb temperatures in stopes in a mine. From the results it has been concluded that a man with an 'average' maximum oxygen intake capacity of about 2. 8 litres/min should be able to work: at 6 shovels/min, or 30 cars/shift per two men, at 76°-84°F; at 5 shovels/min, or 27 cars/shift per two men, at 86°F; and at 4 shovels/min, or 24 cars/shift per two men, at 89°F wet bulb air temperatures. INTRODUCTION A number of gold mines in South Africa still use tram-shovelling extensively. In this method of rock removal from the face of the stope, Bantu mine workers load rock into cars and tram the cars to a centre gulley where they are emptied. Previous studies from this Laboratory3 have shown that tram-shovelling is one of the most arduous tasks underground. The rate of energy expenditure is relatively high, being an oxygen consumption of about 1.4 litres/min over a period of some hours. In cool air conditions the upper limit to the rate of production of the well-motivated men employed on tram-shovelling has been shown1 to depend upon their capacities for physical work of an endurance nature (as measured by their maximum oxygen intakes). However, in hot conditions the factors which set the upper limit to the rate of production are different. They are primarily the ability of the body to maintain a heat balance between the rate of heat production, due to physical work, and the hot atmosphere, so that the men do not develop excessively high body temperatures8. In order to give mine managers guidance on the 'optimum' rate of production of Bantu mine workers engaged upon tram-shovelling under different temperature conditions underground a study was carried out in a mine. The number of shovels per minute and cars per hour were recorded and heart rates and oral temperatures were measured throughout the duration of the shift on samples of 6-10 Bantu mine workers in different air conditions. The results of the study are recorded in this paper and conclusions are drawn as to the number of shovels per minute and cars per hour which Bantu mine workers of 'average' maximum oxygen intake capacity should be able to produce at wet bulb air temperatures of between 76° and 89°F without either excessive fatigue or danger of heat illness.

By G. L. Gomes-Sebastiao, W. W. de Graaf

"Gomes Sand is a quarry operation that produces sand and aggregate for the construction industry. The quarry is experiencing inconsistencies in the fragmentation and poor pit conditions as a result of poor drilling and blasting practices. This results in excessive downtime in the load and haul and crushing processes.A benchmarking exercise of the blasting practices was conducted to evaluate the effect of the inconsistency on the mining cycle. After changes in the blasting practices the downtime was reduced, which improved the crushing plant utilization by 4.9%. The improved blasting practices and more consistent fragmentation decreased the average number of loads lost each month due to jaw crusher blockages from 9.2% to 3.9% of plant throughput. The change in blasting practices also improved pit conditions. IntroductionGomes Sand is a quarry operation that has been in operation since 2009, producing sand and stone for the construction industry. The quarry was experiencing unacceptable blasting results. The repercussions included uneven pit floors, large amounts of oversize rock (>500 mm), and inconsistent fragmentation.The blast results affected the load and haul operations as well as the efficiency of the crusher. This resulted in downtime in the daily operations, and consequent production and revenue losses.The crusher product should have a top size of 50 mm. A blast fragmentation of <50 mm would improve the downstream operations and the crusher throughput.An investigation into the blasting practices was carried out to assess whether the downstream delays can be eliminated by improving the blast results. The exercise included:* Assessing if the designed blast layout is adhered to on the bench* Observing the quality and control of drilling* Observing the charging procedure of the blast-holes* Benchmarking the fragmentation consistency of the blasted rock using current blast design and practices* Analysing the throughput of the crushing plant* Investigating the power consumption of the crushing plant and determine if a change in blasting practices will affect this* Evaluating the hours spent by the hydraulic hammer on secondary breaking."

Jan 1, 2017

Reviewer: R. Graham The chemistry of gold extraction by John Marsden and lain House. Elis Horwood Series in Metals and Associated Materials. Chichester, Elis Horwood. £80. The chronology has been well researched, and the book defines al the milestones. It is a pity that there is no map of the early gold finds in South Africa, which would have offered a comparison with those shown of Australia and the USA. Nevertheless, the &apos;Pre-cyanidation, Cyanidation and Technical Development&apos; eras fall logically into place, and reflect on the advances in social history and civilization, as well as in technology.

Jan 1, 1992

By H. Xuchun, H. Nailian, L. Guoqing

With the accession to WTO and the establishment of Shanghai Gold Exchange, gold mines in China are facing more severe competition from both home and abroad. Supply Chain Management (SCM), a new management idea gradually accepted all over the world, provides the gold mines in China with a new management mode. In this thesis, under the guidance of SCM theory, based on the analyzing to the actualities of Jiaojia Gold Mine, the Jiaojia supply chain framework is constructed, the function system for Jiaojia SCM is configured, and function modules are described in detail. Keywords: Supply Chain Management, Gold mine, Informatization

Jan 1, 2003

By deur J. V. D. M. Grimes

Sishen Iron Ore Mine is one of the largest open-pit mines in the world, and loading and hauling constitutes one of the major cost items on the mine. Because high productivity in loading and hauling results in large financial benefits, the following projects to improve productivity were implemented at Sishen: - a computerized truck-allocation system, - an overhead power-supply system for the dieselelectric driven rear-dump trucks, - an in-pit crusher and a belt-conveyor system. This paper concentrates on the truck-allocation system, with special reference to the improved productivity of loading and hauling resulting from the implementation of this system.

Jan 1, 1984

By H. Skretting, J. Gundeesen

The paper compares operational parameters for the electric reduction smelting of pig iron and ferroalloys in pilot and industrial furnaces. Data from two pilot furnaces of approximately 200 and 500 kW operating-load capacity, as well as from several production furnaces, are included. Examples are given for the smelting of pig iron, ferronickel, ferromanganese, ferrochromium, and ferrosilicon. In most instances, the results from the pilot furnaces, such as the values for consumption and product analyses, corresponded fairly well with comparable data from the industrial furnaces. For ferrosilicon, the power consumption in the pilot furnace was higher than that in the industrial furnace.

Jan 1, 1979

By L. Woollacott, R. P. King

Although several models for the carbon-in-pulp (CIP) or carbon-in-leach (CIL) processes have been published, most of these models do not consider in detail the way in which the carbon phase flows on large-scale plants. This paper illustrates the importance of these details if the CIP or CIL process is to be modeled correctly. An appropriate model, based on population-balance techniques, is then derived. Suitable mathematical techniques for the solution of the model equations are also described. Finally, a method for estimating the model parameters for a full-scale plant is described.

Jan 1, 1990