Search Documents

By M. U. Ozbay

This paper presents an overview of the research that has been carried out to improve the understanding of the fracture processes occurring in rock under high levels of stress. The onset and growth of fractures are studied by means of laboratory model testing, and the results obtained are used in the calibration and validation of the numerical model DIGS, which is based on displacement discontinuity. The results obtained so far have shown that, while there are overall similarities between the experimental results and the numerical simulations, improvements to the experimental procedures and the DIGS are required for a detailed mechanistic understanding of shear-band orientations and extension fractures.

Jan 1, 1996

By C. L. de Jongh

Fracturing of the rock caused considerable difficulties during the boring of a deep-level tunnel in hard rock. A pilot bore was suggested as a possible means of reducing the effect of the fracturing, and this possibility was investigated theoretically by means of a three-dimensional elastic stress analysis. Failure criteria were applied to the results of this analysis, and it was found that fractures predicted by the use of a simple criterion of limiting tensile macrostrain criterion agreed remarkably well with in situ observation. It was concluded that fracture could not be avoided and that a pilot bore was likely to aggravate tunnelling conditions.

Jan 1, 1978

It is shown that, when a flat-bottomed indentor is pressed into the surface of a strong rock, the normal force necessary to cause failure of the rock is reduced substantially if a shear force is applied to the indentor. A mathematical analysis is described, which shows that higher stresses are induced in an elastic material close to the free surface of the material ahead of a punch when a shear force together with a normal force is applied to the punch. Therefore, failure of the material would occur with lower forces applied to the punch. Stress trajectories show that fractures develop in the rock along lines of maximum principal stresses.

Jan 1, 1978

By J. H. deur Potgieter

This paper, 'A review of the biological treatment of cyanide-bearing waste water' discusses the necessity for the treatment of cyanide-bearing waste water with a view to the avoidance of environmental pollution, and the limitations of the available chemical and physical processes are referred to briefly. The sources of cyanide-bearing waste waters are mentioned. The mechanisms of production and utilization of cyanide by fungi and bacteria are discussed. The work done in connection with the biological removal and destruction of cyanide is summarized, the successes achieved are described, and the relevant processes are listed. In conclusion, some advantages of biological processes for the removal of cyanide are mentioned.

Jan 1, 1991

By F. W. Petersen

For the past thirteen years, the Universities of Cape Town and Stellenbosch have hosted an annual symposium to discuss topics relevant to mineral processing. Since 1987, this Symposium has been held under the auspices of the Western Cape Branch of the South African Institute of Mining and Metallurgy, and has become one of the main events on the national conference calendar. In 1989 and 1993, the symposia took the shape of international conferences. This year the 13th Annual Mineral Processing Symposium was organized by the two universities, the Cape Technikon, and the local branch of the South African Institute of Mining and Metallurgy, and was held at the Van Riebeeck Hotel in Gordon's Bay.

Jan 1, 1994

For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984. New President On 29th March, 1985, Mr B.C. (Bertie) Oberholzer, Manager of East Driefontein Gold Mine, was elected President of the Association of Mine Managers of South Africa for the ensuing year. Bullion from old film A pollution-free chemical method of producing silver that is 99 per cent pure-and therefore of bullion quality-from scrap photographic film and paper has been developed by a British company.

Jan 1, 1985

By A. Koursaris, Y. N. Turan

This paper reports the results of a literature review carried out on nitrogen-alloyed austenitic stainless steels and their properties. It was found that a large volume of work has been carried out on the subject, particularly with regard to the more common stainless steels such as types 304 and 316. No work appears to have been conducted on the highly alloyed steels such as type 310S. Nitrogen has been found to increase the stability of the austenite in stainless steels and to impart significant improvements in the mechanical and corrosion properties of these alloys. Importantly, nitrogen appears to increase both the ductility and the strength of austenitic stainless steels over a wide range of temperatures.

Jan 1, 1993

By M. Timucin

High-temperature phase relations and thermodynamics of the condensed phase region of the Pb-S-O system at 1473 K were analysed by use of the available information. The sub-regular solution models on Pb-PbS and PbO-PbSO4 continuous melts were used in conjunction to generate a consistent set of thermodynamic and phase equilibrium conditions for the Pb-S-O system. The directions and distributions of conjugation lines between melts of this system were derived with relevant activity and composition data. The calculations permitted the thermodynamic analysis of direct lead smelting and the construction of isothermal reaction diagrams for the system in terms of oxygen and sulphur partial pressures at 1473 K.

Jan 1, 1989

Results are presented on the elution of gold cyanide and base-metal cyanide complexes from strongand weakbase resins. It is shown that thiocyanate anions, zinc cyanide anions, and thiourea in acid solution are effective eluants of strong-base resins, but that it is generally necessary for electrowinning to be incorporated in the elution cycle if fast rates of elution are to be achieved. Weakbase resins are eluted with sodium hydroxide solution, which is shown to be far simpler and far more effective than the elution of strong-base resins. The effects of parameters such as concentration of the eluant, temperature, and electrowinning efficiency on the rate of elution of the resins are examined.

Jan 1, 1984

By J. A. L. Napier

One of the most important characteristics of tabular mine stress analysis is the need to represent the complex evolution of mining face positions and the accompanying induced stress changes in the rock mass. Integration of seismic activity with numerical modelling requires flexible and efficient solution schemes in which both off-reef damage and large-scale fault slip can be effectively represented. A new approach is investigated in which the stope closure and ride variables can be found using a moving least squares estimator. Some advantages of this approach over traditional element-based tessellation schemes are identified. At the same time, shortcomings of this method are noted when the displacement discontinuity variable is approximated by a polynomial shape function. Difficulties and possible solutions to the shape function formulation near excavation edges are discussed. Une des caractéristiques les plus importantes de l’analyse des contraintes minières tabulaires est la nécessité de représenter la complexe évolution des positions du front de taille et des changements concomitants des contraintes occasionnées dans la masse rocheuse. L’intégration de l’activité sismique avec la modélisation numérique requiert des projets souples et efficaces qui permettent la représentation des dommages hors-filon et des glissements de faille à grande échelle. Une approche nouvelle est étudiée qui permet de trouver la fermeture de la taille et les variables de montage en utilisant un estimateur par les moindres carrés mobile. Certains des avantages de cette approche sur les traditionnels projets basés sur une structure en mosaïque sont identifiés. En même temps, les défauts de cette méthode sont notés lorsqu’on calcule la variable de discontinuité du déplacement approximativement par une fonction de forme polynomiale. Les difficultés et solutions possibles à la formulation de la fonction forme près des bords d’excavation sont discutés. Eine der wichtigsten Charaketeristika der taublaren Grubenspannungsanalayse ist die Notwendigkeit, die komplexe Entwicklung der Abbaupositionen und der damit verbundenen induzierten Spannungsänderungen der Gesteinsmasse neu vorzulegen. Die Integration der seismischen Tätigkeit mit einem numerischen Modell erfordert flexible und effiziente Lösungsschemata, in denen sowohl Schäden ausserhalb des Riffs als auch Verwerfungen großen Ausmaßes effektiv dargestellt werden. Ein neuer Vorstoß wird untersucht in welchem die Strossenschliessung und Schneisenvariablen unter Verwendung des Schätzwertes der kleinsten quadratischen Abweichungen (Gaussscher Schätzwert) gefunden werden. Einige Vorteile dieser Annäherung im Vergleich zu der traditionellen Element-basierenden Tessellation sind identifiziert. Gleichzeitig werden Unzulänglichkeiten dieser Methode vermerkt, wenn die Verschiebungsdiskoniuitätsvariable durch eine polynomische Formfunktion angepaßt wird. Schwierigkeiten und mögliche Lösungen zur Formfunktionsformulierung nahe Exkavationsrändern werden besprochen.

Jan 1, 2003

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By R. G. B. Pickering

The Faculty of Engineering at the University of the Witwatersrand and the Mining Technology Division of the CSIR have co-operated to define the problems associated with deep level mining and in this paper they will identify what they consider to be the critical areas requiring technological solutions. This perspective will then be applied to work currently being carried out by both the organizations and gaps for additional developments will be identified. Finally the Co-operative Research Centre methodology operating in Australia is described. The purpose of this CRC is to provide a vehicle for R&D co-operation to develop and implement technologies which will increase the competitiveness of the mining industry. A further objective is to develop an appropriately skilled human resource base.

Jan 1, 1996

By S. Visage

By 1984 Iscor's first direct-reduction plant will be operating at the Vanderbijlpark Works, and for the fin;t time the Corporation will have an alternative method to the blast furnace for producing iron from ore. The performance of Iscor's four-kiln plant, which will be the largest coal-based plant in the world producing sponge iron, will undoubtedly be watched with great interest by steelmakers throughout the world. Beneficiation of tin The Southeast Asia Tin Research and Development (SEATRAD) Centre is a regional oganization, formed by the Governments of Indonesia, Malaysia, and Thailand with assistance from the United Nations, to conduct, coordinate, and promote research and training in the various fields of tin production, including geology, prospecting, mining, mineral processing, and smelting.

Jan 1, 1982

By R. G. B. Pickering

The Faculty of Engineering at the University of the Witwatersrand and the Mining Technology Division of the CSIR have co-operated to define the problems associated with deep level mining and in this paper they will identify what they consider to be the critical areas requiring technological solutions. This perspective will then be applied to work currently being carried out by both the organizations and gaps for additional developments will be identified. Finally the Co-operative Research Centre methodology operating in Australia is described. The purpose of this CRC is to provide a vehicle for R&D co-operation to develop and implement technologies which will increase the competitiveness of the mining industry. A further objective is to develop an appropriately skilled human resource base.

Jan 1, 1996

By K. C. Sole

The International Solvent Extraction Conference takes place every three years, under the auspices of the international Solvent Extraction Committee. ISEC '96 held in Melbourne, Australia, in March 1996, was attended by delegates from 34 countries. South Africa was well represented, with delegates from Amplats, De Beers, Mintek, Western Platinum Refinery, and independent consultant Phillip Lloyd (who represents South Africa on the International Committee). The theme of this year's conference was 'Value Adding through Solvent Extraction'. Five plenary lectures were presented. Dr E. Blass of Germany gave the opening presentation entitled 'Solvent extraction-a historical review', which traced evidence for the use of solvent extraction (SX) from the time of the ancient Egyptians, through the Middle Ages and Renaissance, to the Industrial Revolution.

Jan 1, 1996

By R. E. Gundersen

Hydro-power-the use of high-pressure water as an energy source-offers tremendous benefits for environmental control in deep, hot mines. The extent of these benefits depends on the mining method, the selection of equipment to be hydro-powered, and the efficiency with which the coolth is extracted from the water and into the working environment. The engineering of hydro-power systems continues to receive much attention. However, this paper considers the environmental implications of using hydro-powered equipment, particularly with regard to positional efficiency. The integration of hydro-power with developments such as backfill, mechanization, and higher face-advance rates is discussed. Layouts are proposed that attempt to minimize the quantity of water in circulation by extracting the maximum coolth from the water.

Jan 1, 1990

By M. Mrost

Slimes disposal at South African gold mines by M. MROST*. M.Sc. (Rand) (Fellow) The soil mechanics, civil engineering, and environmental considerations applicable to the construction of slimes dams on the Witwatersrand gold mines are discussed. It is concluded that, though the procedures used in the construction of dam embankments do not accord with the best possible practice, they are entirely adequate in current local circumstances, provided that proper precautions are taken to ensure that the wall foundations are sufficiently permeable and strong, and that the dams are protected against erosion. If current trends towards larger mining and metallurgical complexes continue, it may become necessary to build larger, higher dams, and to adopt slimes embankmentbuilding practices that are inherently more reliable.

Jan 2, 1974

By J. J. Geldenhuys

Premier of the North-West Province, Mr Molefe, foreign dignitaries and guests, ladies and gentlemen. It is a pleasure and also a special honour for me to have been invited here this morning to make this address. The xv Congress of the Council of Mining and Metallurgical Institutions is, by its very nature, an extremely important event for the international minerals industry. But I believe that this specific Congress assumes an even greater significance because of the profound and far-reaching changes that have taken place in South Africa this year. These are exhilarating times, a period when so much in our country has altered and when so much has to be done so quickly to build positively on our bold political decisions.

Jan 1, 1994

By Donald J. Murdock

Column flotation has been developed over the past ten years as an alternative to conventional flotation. It has been used mainly in the cleaning applications of sulphide flotation, where its ability to wash the froth of entrained gangue and produce a higher-grade product has given it a distinct advantage over other technology. The benefits of column flotation can be summarized as follows: Improved concentrate gradeby 2 to 5 per cent . Significantly lower operating costs . Savings in capital investment . Superior control. Since the initial development of the equipment, a number of design improvements have been developed that now form the basis of the Cominco column-cell design. The purpose of this article is to discuss some of those design innovations, and present some typical industrial results.

Jan 1, 1991

By B. Jack, A. Vervoort

During pillar extraction, sidewall fracturing and spalling at some collieries constitute a severe stratacontrol problem. In order to obtain a better understanding of this phenomenon, a survey of pillar corner conditions before and during pillar extraction was conducted at one particular site. For the various successive mining steps, the vertical stresses on the pillar corners were calculated by use of a three-dimensional boundary element program. A significant correlation was found between the calculated vertical stress prior to the extraction of the panel and the sidewall conditions. During the extraction of the panel, a significant deterioration of the sidewall conditions at a pillar occurred only when the adjacent pillar was mined, causing an increase in vertical stress on the remaining pillar.

Jan 1, 1992