Search Documents

By D. Brazier, W. Laing, D. Nixon

Keywords: Pyrometallurgy, furnace, smelter, copper, Palabora The Palabora copper smelter has operated for the past 38 years, treating concentrates produced at the mine site. Palabora has reduced captive material by almost 40 per cent with the transition from a large open-cast to a smaller underground mine. The smelter and refinery complex was designed to treat 120 kt contained copper units per annum, with the underground only supplying 70 per cent of the feed. The agreed strategy was to import enough concentrates to maximise production and reduce operational unit costs. This transition has presented the Palabora management with new challenges both in technical and financial aspects.

Jan 1, 2006

By A. R. Barnes, C. W. P. Finn

The prereduction and smelting characteristics of UG-2 ore were studied and compared with those of Winterveld chromite ore. The UG-2 ore proved more reducible, and substantial prereduction (over 70 per cent reduction after 30 minutes at 1250oC) was obtained. No difficulty was experienced in the production oh high-carbon ferrochromium alloy containing 48 to 50 per cent chromium. Calculations of the energy balance show that UG-2 chromite has lower total energy requirements (both on the basis of unit of ferrochromium produced and of total chromium content). More than 50 per cent of the energy required for reduction can be supplied outside the smelting furnace.

Jan 1, 1983

Results from a study undertaken at a Transvaal colliery on the feasibility of undermining an urban development by conventional bord-and-pillar mining operations in the No. 4 Seam of the Highveld Coalfield are discussed. Surface ground vibrations above production sections were measured, analysed, and then compared with well-accepted guidelines so that the expected effects of vibration on inhabitants and surface structures could be determined. The measurement and scaling of ground vibration from blasting are outlined, and the effects on humans and structures are discussed. It is concluded that residential areas can be safely undermined by conventional drilling and blasting techniques provided certain simple guidelines are followed.

Jan 1, 1987

By G. E. Blight

The load-compression characteristics of mine supports are usually evaluated by means of relatively rapid tests, whereas in the mine they are subjected to much slower strain-controlled compression. The effects of slow strain rates on the load-bearing properties of mine supports were explored by means of straincontrolled tests on model timber packs and timber-filled steel telescopic props. It is shown that the load-compression characteristics of these supports are considerably influenced by the rate at which they are compressed. The species of timber influences the behaviour, but to a relatively minor extent. Preloaded supports are shown to lose a significant proportion of their preload by relaxation.

Jan 1, 1978

By D. H. Hillhouse, G. Lange

Design features of a deep-level shaft by D. H. HILLHOUSE. Pr. Eng.(Visitor)- and G. LANGE. Pr. Eng.(Fellow) Design and technical features of a large, deep shaft are described, and details of the sinking equipment are given. Special features in shaft steelwork, materials handling, and station layouts are described and illustrated. The details of the precast brattice wall are given, together with the reasons for the separation of all steelwork from the brattice wall. A newly developed device for the location of the shaft conveyances while loading or unloading at underground stations is briefly described and illustrated. The paper concludes with a summary showing the rates of progress and costs for the shaft-sinking operation.

By B. J. Pieters

The paper describes the difficulties experienced with inferior coking coals as Iscor began using larger blast furnaces for the production of liquid iron. Research conducted at Iscor from 1977 to 1979 showed that benefits could be gained from the use of partially briqueted charges, and it was decided to install briqueting plants at the Vanderbijlpark and Newcastle Works. Details are given of the later plant, which was supplied by a consortium consisting of Voest Alpine, Didier Engineering, and Sumitomo Metal Industries. Sumitomo also supplied information on the optimization of coke quality along the lines of their Sumicoal System. The results have been a marked improvement in coke quality, much better blast-furnace operation, and increased productivity.

Jan 1, 1991

By K. R. Johnson

Changes in the pattern of computer systems for mine planning and geologic evaluation are occurring as a consequence of the introduction of 3-D high performance graphics terminals. The VULCAN system is described and an outline of its functionality is discussed. Increasingly, the integration of both database systems and graphics and databases will occur, allowing a greater degree of information access to mine operators. The system covers areas of database, drillhole graphics, mine design and layout, surface and solid modelling as well as reserve inventory generation. The design of the software is such that it is fairly commodity-independent and entirely menu-driven, to enable non computer-trained personnel easily to access the system.

Jan 1, 1987

By E. Mpoloka

Debswana together with ADP as their design partner have embarked on an RDP project at Jwaneng Mine. The objective of the project is to install a 2 million ton per annum mineral processing plant that will fast track the recovery of diamonds from the Debswana tailings resource to ensure maximum return on investment for the company. Due to the prevailing economic conditions Debswana has had to review the way they used to build plants in the past and consider simple, fast and effective ways of doing things. The rapid deployment plant concept is therefore the most suitable means of achieving this objective. Debswana is also considering an operating partner who will operate far more efficiently and cheaply compared to the larger more cumbersome and less agile Debswana.

Jan 1, 2010

By A. Ball

A fully instrumented laboratory drilling machine is described. It is designed to produce realistic drilling conditions with diamond microbits of 20 mm diameter. A computer-controlled data-logging system records the net power consumption, rotational velocity, bit thrust, torque, and penetration rate. Tests can be conducted under conditions of set thrust and rate of advance. In the tests reported, there is a significant correlation between the rock drilability and the measured rock properties of relative abrasion resistance and uniaxial compressive strength. Wear of a diamond bit is a crucial factor that cannot be determined simply from rock properties. Realistic drilability testing with appropriately scaled microbits is a convenient and economical way of evaluating diamond-bit performance and determining rock drilability.

Jan 1, 1990

By A. G. W. Knock

Logistic curves are used in the prediction of the primary production of tin metal from estimated worldwide resources. Such curves are asymptotic to the total cumulative reserves, which are a function of prevailing metal prices and total resources. The figures for tin resources are based on the findings of Robertson and of Brobst and Pratt, the latter authors including estimates of undiscovered deposits. It is suggested that tin production will slump from the present level to 100000 long tons per annum by the end of the century, but will reach a new peak of 200 000 long tons some thirty years later. It appears that production will never exceed 300000 long tons per annum unless substantial new resources, excluding those predicted, are discovered.

Jan 1, 1979

Financial Times Mining International Year Book 1979. London, The Financial Times Limited, 1979. 712 pp. Price: airmail, U .S. $60,00; surface mail, U .S. $42,00. International Wrought Copper Council. Glossary of terms applicable to wrought products in copper and copper alloys. London, the Council (6 Bathurst Street, Sussex Square, London W2 2SD), 1978. 170 pp. 80 Swiss francs (approximately £25). Council of Mining and Metallurgical Institutions At a meeting of the Council of Commonwealth Mining and Metallurgical Institutions held on 15th January, 1979, it was unanimously agreed that the name of the Council should be changed.. Assaying and analytical techniques This year sees the Diamond Jubilee of the South African Institute of Assayers and Analysts, which held its first meeting on the 3rd of May, 1919.

Jan 1, 1979

By P. J. D. Lloyd

The Witwatersrand reefs contain gold, uranium, and pyrite in the following average concentrations: 0,001 per cent, 0,02 per cent, and 1,7 per cent respectively. The paper discusses the flotation of pyrite to produce a s,ulphide concentrate, reviews work done on the production of gold concentrates, discusses attempts to produce maximum concentrates, and closes with a review of processes for the simultaneous flotation of these three species. It is concluded that high recoveries of all three species can be achieved only if a rougher concentrate of perhaps 20 per cent of the feed (by mass) IS produced, and it is suggested that reverse leaching (leaching before cyanidation) of this concentrate, followed by a cleaning flotation step for the recovery of the pyrite, would be more efficient than the routes employed at present.

Jan 1, 1981

By K. M. Banks

Multiple-pass hot-strip-rolling schedules of carbon steels and niobium-microalloyed ferrite-pearlite steels were simulated on a Gleeble 1500 thermomechanical test apparatus. The effects of finishing temperature, coiling temperature, and chemical composition on the as-deformed ferrite grain size and hardness of the steels were determined. Low finishing temperatures and low coiling temperatures both contributed to ferrite grain refinement. Good agreement was found for the microstructure and hardness of the steels between the as-ruled condition and the results obtained from rolling simulations. The progress of recrystalization and precipitation was followed from examinations of the flow-stress curves during the hot-rolling simulations. The flow-stress behaviour during the finishing passes was consistent with the resulting changes in final ferrite grain size. It was found that the no-recrystalization temperature, TNR, is raised by increased additions of niobium.

Jan 1, 1993

Historical Background. South Africa's industrial history began with the discovery of gold and diamonds during the last century, and the mining industry was the first chief component of our technological development. During the past six decades, quantum leaps were made in other fields, too, when other industries and research bodies such as Escom, NDC, Iscor, Sasol, Foskor, Alusaf, Mintek, cs I R, SA B S, and A E C were established. These meaningful additions have two outstanding characteristics. Firstly, they were linked mainly to primary activities such as energy and minerals and, secondly, their establishment was to a large extent due to the driving force of individuals such as Van der Bijl, Van Eck, Rossouw, Schonland, and Roux, rather than to impersonal government policy. Encouraging signs of the evolution of such policy has emerged during the past few years.

Jan 1, 1989

By A. Ward, A. Smith, D. Harpley

Methods for the prediction of seepage quality from waste-disposal facilities are evaluated for input to the design of desalination treatment facilities. This is done by reference to a waste dump seeping into a near-surface aquifer, the contaminated seepage being collected by scavenger wells. As the quality of contaminated water intercepted by the wells will vary with both space and time, it is necessary for predictive methods to accommodate such variations. One-dimensional and two-dimensional predictive solute transport models are described and applied to the seepage and scavenger-well example mentioned above. The advantages and disadvantages, interims of overall applicability, data requirements, and possible accuracy, are described and discussed. While one-dimensional models have the advantages of speed, simplicity, and cost, the frequent requirement of prediction in both space and time necessitates more complex, two-dimensional simulation.

Jan 1, 1987

By J. Keyser

The realization of an Integrated Technical Resource Asset Management System (ITRAMS) has so far evaded all software developers in the mining industry. The major factors that have prevented the development of such a system are limitations on software, hardware and network systems. Several factors have come together at Venetia Mine, which has made the undertaking of such a project both possible and desirable. This has led to the formation of a strategic partnership between Venetia Mine and Gemcom Software International Inc. This partnership is dedicated to develop and provide an Integrated Technical Resource Asset Management System based on Microsoft Back Office architecture, Gemcom for Windows™ and the MinRas system. This paper will elaborate on the phased approach of the integration of systems into the core repository, mechanisms of integration, the functionality of the system, final results, techno-economic benefits and general project management issues.

Sep 1, 2001

1. New books from The Institute of Metals Physical and elastic characterisation, edited by M. McLean. 1989. 228 pp. £25.00.High nitrogen steels, edited by J. Foct and A. Hendry. 1989. 461 pp. £49.50. Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15.Design for recyc/ability, by Michael E. Henstock. 1988. 150 pp. £15. Solidification processing. 1988. 549 pp. £45.Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15.Marine engineering with copper-nickel. 1988. 103 pp. £18.Sir Henry Bessemer: An autobiography. 1989.380 pp. £16.95. 2. Other publishers Occupational safety and accident prevention. Behavioural strategies and methods, by C.G. Hoyos and B.M. Zimolong. Amsterdam, Elsevier, 1988. 218 pp. Dfl. 180.00. Algorithms in real algebraic geometry, edited by Denis S. Arnon and Bruno Buchberger. London, Academic Press, 1988. 274 pp. £15.95.

Jan 1, 1989

By E. J. Magri

This paper describes a geostatistical study of the relative merits of diamond-saw sampling and conventional chip sampling, using results from experimental work carried out on Randfontein Estates Gold Mine and Western Areas Gold Mine. The diamond-saw sampling procedure is described, and it is concluded that this is a very efficient operation and leads to good-quality sampling that is clearly an improvement over conventional chip sampling. The study principally involved the computation of the errors of estimation of the mea gold value of mining panels for the two sampling methods, revealing that, in the normal production environment, the diamond-saw sampling method is a significant improvement over conventional chip sampling, as evidenced by the reduced estimation errors achieved. The question of optimum sample spacing is discussed, and it is concluded that the required spacing for chip sampling needs to be smaller than for the diamond-saw method.

Jan 1, 1986

The Water Year Office for South Africa has supplied a provisional list of scientific congresses and meetings due to be held during 1970 with "Water" as the main or secondary theme, as follows: February: SARCCUS conference on "Water for Progress," Lourenco Marques. March 16-20: Annual Congress, Institute for Water Pollution Control, Cape Town. May: Possible S.A. Akademie conference on Cooling Tower Experiments, Pretoria. May: Annual Meeting of Association of Municipal Electricity Undertakings, Potchefstroom. May 27-29: Congress on "Water Resources of Natal", Durban. June 29/July 4: Annual Congress, South African Association for the Advancement of Science, Cape Town. July 2: Joint meeting of South African Association for the Advancement of Science and S.A. Akademie, Stellenbosch. July: Winter School, Federation of University Engineering Students. July: Youth Science Week. Foundation for Education, Science and Technology. July 21-24: The South African Tunneling Conference. September: Proposed SARCCUS conference on water in Nature Conservation, Skukuza. November 16-20: International Convention on "Water for the Future", Pretoria.

By R. C. Urquhart, D. D. Howat, R. I. L. Guthrie

Heat losses from ladles during teeming by R. C. URQUHART, M.Eng. (McGiII), Ph.D. (Visitor). R. I. L. GUTHRIE, B.Sc. (Eng.) (London), A.R.S.M., Ph.D., D.I.C. (Visitor), and D. D. HOWAT, B.Sc. (Glas.), Ph.D. (Fellow) In an investigation of the loss of temperature by liquid steel during a teeming operation, a numerical technique was used to calculate the heat flows and the rate of temperature drop over the entire teeming operation. The calculations show that, before teeming, approximately 50 per cent of the heat loss is into the ladle wall at the level of the metal. As teeming progresses, the amount of heat lost by radiation to the wall above the metalline increases. The effect of variables, such as initial metal temperature, the preheat of the ladle and ladle cover, and delays, on the rate of temperature loss by the metal were determined.

Jan 11, 1973