Search Documents

By B. K. Mishra, R. K. Rajamani

Discrete element is a numerical technique for describing the collision dynamics and motion of an assembly of particles. In particular, calculations are done on full three-dimensional space with a force-contact law for collisions and Newton’s law for subsequent motion. It may be said that there is no empiricism in this approach. The paper describes the full scale simulation of large diameter semiautogenous grinding mill of size 40X24 ft. It is shown that the simulation predicts the power draft of plant size mill extremely accurately. Also these simulations have been adapted uniquely to assess the motion of pebbles and slurry in pulp lifters. The passage of slurry from pulp lifters into trunnion is extremely important since flow-back and carryover must be avoided at all cost. The dynamics of slurry flow through pulp lifters is also described in this paper.

Jan 1, 2003

By D. Belin

Treatment of dilute acid mine drainage and similarly polluted water is becoming increasingly complicated. The pressure of economics is now exacerbated by legislation which classifies as hazardous waste the precipitates from conventional lime treatment plants. Since acid mine drainage invariably contains sulfate ions, one solution is to use anaerobic Desulfovibrio type bacteria to reduce the sulfate into sulphide ions which could then be used to precipitate out the heavy metals. Results are presented for both batch flask cultures and continuous column tests. Compost was used as the bacterial substrate in the column test which simulated heaps. Conditions changed from aerobic to the required anaerobic deep in the columns. Polluted feeds (up to 700 mg/l zinc) gave effluent containing well below I mg/l zinc over extended periods. Direct transfer of sulphide ions through a stream from an isolated container of bacteria is a good alternative.

Jan 1, 1991

By I. Michalakis

A geological and geophysical study was con-ducted at the area of Stylos, Hania in order to study the possible mechanisms of saltwater contamination. A new detailed geologic map in scale 1:5,000 was combined with the results of a time lapse geophysical survey using seismic and electrical methods. A fault system in the N-NE direction possibly favors the saltwater intrusion.

Jan 1, 2006

By Todd S. Harris

Industrial minerals or non-metallic minerals are loosely used terms applied to a diverse assortment of materials which, in many cases, have nothing more in common other than the fact that they are neither metals nor fuel minerals. To help bring order to this otherwise random assortment of minerals, we have grouped these materials into two main categories; chemical and physical minerals, and nine sub-categories based on end-use applications as shown in Table 1. Chemical minerals are products which are principally used for the specific chemical elements they contain, whereas physical minerals are products which are used to meet specific performance specifications. The latter part of the 1970?s, in particular 1978, were considered peak years in terms of production and sales for many industries, By using 1978 as a base year, we can evaluate wherethese markets stand today after the recession of the early 1980's and the recovery which began several years ago. From this historical overview and appraisal of the current situation, various assumptions can be drawn as to which markets are expected to perform well into the 1990's.

Jan 1, 1987

In this presentation, CiDRA?s patented technology platform and its applications will be described. CiDRA's non-invasive, passive sonar array-based flow meter technology provides the volumetric flow rate of single or multiphase fluids by measuring the speed at which naturally occurring structures such as turbulent eddies or density variations convect with the flow past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. This technology has resulted in a unique ability to measure the flow rate of most fluids ? clean liquids, high solids content slurries, pastes, and liquids and slurries with entrained air. Unique and difficult minerals processing flow measurement problems and their solutions will be described. Examples of these problems include flow measurements in froth lines and flotation feed lines with entrained air, slurry lines with magnetite and other magnetic ore, slurry lines with abrasive or corrosive materials, high pressure lines, and lines exhibiting scale buildup. Recent technology developments will be covered.

Jan 1, 2008

By A. J. Lynch, M. J. Lees

Introduction The design of wet grinding circuits may vary considerably according to the duty which is to be performed. Grinding machines which are commonly used in these circuits are rod mills, ball mills, autoge¬nous mills, and pebble mills while size separation machines commonly used are vibrating and wedge-wire screens, hydrocyclones, and rake classifiers. In some circuits, such as those producing feed to cement kilns, all the ore entering the circuit is discharged in a single product stream. In others, such as those operating on magnetite-taconite ores, the feed entering the circuit leaves in two or more streams. Grinding circuits in flotation plants normally include sections in which either the concentrate or the tailings from the primary flotation circuit is reground and these additional sections should be regarded as an inte¬gral part of the grinding circuit. A typical circuit is shown in Fig. 18. Problems in achieving maximum efficiency may occur at three stages: 1) At the design stage when the optimum size reduction flow¬sheet must be selected with respect to the types, numbers, and sizes of processing units. 2) At the operating stage when the correct selection of values must be made for those variables which may be altered while the circuit is off-line but which are constant while the circuit is on-line, for instance the vortex finder diameter of the cyclones. 3) Under conditions of continuous operation when changes in the circuit feed or in the mechanical operation of the circuit may cause undesirable changes in the circuit product. The first two prob¬lems are concerned with optimization, that is, with making the best choice from many possibilities, and the last with control. Optimization Problems. The main purpose of a wet grinding circuit is to produce particles with a sizing distribution which will ensure optimum performance of the later chemical reaction or physical concentration circuits, because it is on the efficiency of these later circuits that the economics of the total mineral treatment process depend. The size distribution of the product from a grinding circuit may be affected by many variables, some concerned with the arrange¬ment and operation of the machines and some concerned with the ore characteristics, and it is important that these should be recognized in the design and operation of the circuit. For instance, in a simple ball mill-cyclone circuit the variables which affect the product size even for constant feed characteristics are shown in Fig. 19. In addition, the rate, size, hardness, and mineralogical composition of the feed will affect the performance of the circuit and the product size. When the circuit contains more than one mill, both the number of choices available and the complexity of the problem are increased consider¬ably. Consequently, one type of problem which is to be solved if an optimum product is to be obtained from an existing grinding circuit is that of circuit design, and this includes arrangement of processing units and selection of those operating conditions which cannot be altered when the circuit is operating, such as mill speed and cyclone inlet and outlet dimensions. The other major problem in optimization is encountered at the design stage when a choice must be made about the type, number, and size of processing units. For instance, for a typical high-capacity size reduction operation, should two circuits each containing one rod mill and two ball mills or three circuits each containing one rod mill and one ball mill be used? Alternatively, should ball mills only be used and if so, how many, what size, and what arrangement?

Jan 1, 1985

By Frits Agterberg

Statistical exploration uses statistical methods to identify targets for more detailed investigation by estimating the odds of occurrence of mineral deposits. The study area which contains the possible targets may be as large as 1 000 000 km2 or as small as 100 km2. Results are presented in terms of a probability index for the existence of a deposit or, more precisely, in terms of expected dollar value for a unit area, or even in terms of number, size, and grade of deposits remaining to be discovered. Typically, selected geological, geophysical, or geochemical information is systematically quantified and statistically analyzed by using the computer in order to distinguish between geological environments on the basis of the probability that they contain undiscovered deposits of a specific type. All possible targets are compared with one another by using information on areas known to contain deposits. The information on the known areas is either a set of control data consisting of values for the same parameters as are quantified for the entire study area, or it embodies a specific model for the occurrence of a given deposit type. Examples of both procedures will be discussed in this chapter.

Jan 1, 1979

By Gareth Mainwaring

The Cross Harbor Freight Movement Project is currently in the Environmental Impact Statement phase. The scheme is addressing alternative solutions to transport freight across the Upper Bay of New York Harbor, from New Jersey through to Brooklyn, Queens and Long Island. Amongst the alternatives being assessed are two tunnel options; from the north shore of Staten Island through to Brooklyn, and from Jersey City to Brooklyn. These tunnels are approximately 30,000 feet in length, and with up to17,000 feet under the Harbor, would make it one of the longest undersea crossings in the world.. The paper addresses the development of the project, from the Major Investment Study through to the current EIS, and describes the tunnel schemes that are being taken forward. The geological conditions that will be encountered, proposed construction methods, and the ventilation issues associated with such major undersea tunnels will all be described.

Jan 1, 2003

By Patrick Doig, Ross Webb

The Bradshaw Section 5A Interceptor involves the construction of two miles of 108-inch, finished diameter tunnel in dry soils. Excavation is generally by Lovat TBM with ribs and lagging support. The tunnel is beneath a recreational parkway and stringent measures have been enacted to preserve the parkway and minimize disruption to the neighborhood. Apart from these constraints, the project would have been unremarkable but for the intervention of CalOSHA and the local fire department who ordered extraordinary fire protection measures. The paper discusses the cause and effect of these measures and comments on the potential repercussions for other projects.

Jan 1, 1999

By L. E. Allen, J. F. Abel, D. R. Morgan

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for disposal of transuranic waste and is operated by the U.S. Department of Energy (DOE). The repository is located at a depth of 655 m in the Permian age salt beds of the Salado Formation, 40 km east of Carlsbad, NM. A key component in the design of the WIPP repository is the installation of concrete structures as panel seals in the intake and exhaust drifts after a panel has been filled with waste containers. The DOE has proposed several panel closure design modifications to the EPA. EPA approval of the changes is required since the details of the designs are specified in EPA’s final rule as a condition for WIPP certification. The Environmental Evaluation Group, in its role of providing technical oversight on the WIPP project, has evaluated the proposed modifications. An analysis of this evaluation is discussed.

Jan 1, 2003

By Scott G. Britton

This chapter is concerned with the construction of the dynamic component of belt haulage systems. The dynamic system includes the belt line and tailpiece extension and retraction movements in a production system where mine management is continually placing the belt in the most effective operating position. Correct installation of the belt and tailpiece during an extension is very important for many performance reasons. Two of the most important reasons are to eliminate spillage and safely operate the belt line. This chapter is divided into three major discussions. The first discussion looks at analyzing the parameters of effective belt line construction. This includes a review of the parameters and management tools needed for proper scheduling of a move-up. The second major discussion topic centers on efficient procedures for a belt line extension. Topics such as site preparation, tailpiece breakdown and setup, stringing the belt line and structure, plus operating and maintenance tasks needed after the belt line is installed and running, are covered. The third discussion presents a list of conveyor and conveyor component manufacturers who provide services and products to the coal mining industry. Again, any discussion on underground haulage systems must generalize much of the site specific design approaches to be practical. This text will mention, where applicable, some of the alternatives available to construction engineers in designing belt line systems.

Jan 1, 1983

By J. J. Crowhurst

The modem open pit-heap leach operation by Pegasus Gold Ltd. at Zortman and Landusky in Phillips County, Montana, is a new chapter in the mining of gold in these districts. The discovery of bulk tonnage ore bodies and their development and ultimate production was based on a long history of mining and exploration in that part of Montana. Gold was originally discovered in the Little Rocky Mountains as placer deposits by Pike Landusky and Lou Myers. This discovery in the 1880s was not significant, but Pike Landusky continued prospecting for lode deposits, and he eventually located the Gold Bug and Little Ben, two of the larger Au-Ag producers in the district. Eventually two camps, Landusky and Zortman, grew in the LittleRocky Mountains. By the time Landusky was killed in 1894 by Kid Curry, the district was still a discontinuous small producer. Steady production commenced in 1907 with the organization of the August Gold Mining Co. Eventually high grade ores on specific veins were exhausted by selective underground mining and the district was idle by May 1942. After World War II in the early 1950s. E.A. Scholz tried to continue selective underground mining, but he realized the stockworks surrounding the larger veins constituted bulk tonnage targets. Ultimately in the 1976- 1979 period he organized two exploration efforts, one each for the Landusky and Zortman areas, and brought these into production as the Argo and Pegasus gold mines. By the time of his death, Apr. 8, 1980, both operations were producing gold. Later the two companies were merged as Pegasus Gold Ltd. Upon the death of Scholz, V.F. Hollister continued as the geological consultant, Ed Roper was engaged as general manager, and J. J. Crowhurst was given the responsibility of executive vice president. The discovery of open pittable ores and the application of heap leach technology was important in the development of mining. Both contributed to the low cost operation that continues to this day. The attached article by L.M. Rogers, then chief geologist, and M.S. Enders, his assistant, describes the geology of the deposit. It was presented at the Northwest Mining Association meeting in 1982.

Jan 1, 1990

By P. Bissert, L. Yan, D. Yantek

"Federal regulations require refuge alternatives (RAs) in underground coal mines to sustain life for 96 hours while maintaining an apparent temperature (AT) below 35°C (95°F). NIOSH research has shown that heat and humidity buildup is a major concern with RAs because they have a limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding an RA is very complex and is not easily defined analytically nor experimentally. To investigate heat and humidity buildup in RAs, NIOSH conducted multiple in-mine 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA. The test results show that when moisture was introduced into the tests to represent perspiration and respiration from miners (wet tests), the average measured internal air temperature at midheight increased by 7.7°C, 9.4°C, and 10.5°C, and the RH approached 95%, 94%, and 88%, respectively. For the dry tests when no moisture was introduced, the average internal temperature increased by 8.4°C, 10.3°C, and 12.6°C, respectively. INTRODUCTION If an accident occurs in an underground coal mine, miners who cannot escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the thermal environment inside the RA. The metabolic heat of the occupants and the heat released by the CO2 scrubbing system will cause the interior air temperature to increase. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The internal thermal conditions can subject miners to heat stress, which can lead to heat exhaustion, heat stroke, or even death depending on duration and magnitude of exposure. MSHA regulations require that RAs must be designed to ensure that the internal apparent temperature does not exceed 35°C (95°F) when the RA is fully occupied [1]. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Before a mobile RA can be deployed at an underground mine for emergency usage, it must be tested to show that its internal AT when fully occupied will not exceed the 35°C (95°F) limit. For practical reasons, RA manufacturers usually conduct their tests at above-ground test facilities. To investigate RA thermal response in an in-mine environment, NIOSH conducted multiple 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA in its underground coal mine facility. The work described in this paper could be used by RA manufacturers to determine a final temperature rise based solely on dry and time-reduced testing."

Jan 1, 2017

By William E. Foreman

Editor's Note: For purposes of uniformity throughout this book, Coal Preparation, 5th Edition, the editors have advocated the use of the U.S.A. Sieve Series of testing sieves (see Table 6-2) as the testing sieves of modem choice. The adoption and use of the U.S.A. Sieve Series and its forerunner, the Tyler Standard Screen Scale, has for over seventy-five years introduced uniformity into reports; has simplified the comparison of results; and has provided control for operation of modem coal preparation circuits. While a full explanation of the differences, and more importantly the similarities of these two measuring systems cannot be stated here, it is felt that a brief clarification of terms is in order. The difference between the U.S.A. Sieve Series and the Tyler Standard Screen Scale Sieve Series is the identification method. Tyler Screen Scale sieves are identified by mesh designation with the width of opening varying by the square root of two, or 1.414 times the width of opening in the previous sieve. The U.S.A. Sieves are identified by openings in millimeters or microns and also arbitrary numbers which do not necessarily mean the mesh count; this series uses width of opening variations in the order of approximately the ratio of the fourth root of two, or 1.189. Tyler Standard Screen Scale and U.S.A. Sieves can be used interchangeably, and to avoid confusion the nameplate of all Tyler Screen Scale sieves show the U.S.A. Number, while all U.S.A. Sieves show Tyler Screen Scale mesh equivalent numbers on the nameplate. INTRODUCTION Sizing is the process of separating mixed mineral particles into groups of particles all of the same size, or into groups in which all particles range between definite maximum and minimum sizes. This chapter applies the modem mechanical screen and the liquid-solid cyclone (hydrocyclone) to the process of sizing solid particles as applied to coal preparation. Screening is a mechanical process that separates particles by size. Modem coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modem preparation plants is done for the following reasons: 1. Removal of fine coal before a size reduction step. 2. Size separation of the coal into a coarse and fine fraction for sized products or for processing in coarse and fine coal circuits. 3. Recovery of heavy media from heavy media coal cleaning circuits.

Jan 1, 1991

By Ing. E. h. Martin Herrenknecht, Werner Burger

In recent years, there has been a dramatic increase in the number of machine driven soft ground tunnelling projects. This increase is largely due to the technological development of slurry and EPB Shield systems. A new generation of soft ground tunnelling machines, markedly different from those of five years ago, now overcomes ground conditions that until now were too costly and impractical to undertake. The paper reviews the latest soft ground tunnelling machine developments in material transport, guidance and control, seismic surveying, soil conditioning, settlement control, cutting tool applications and variable mode operating systems. Specific projects where this technology has been applied will be highlighted.

Jan 1, 1999

By John Todhunter

Longwall mining is certainly not new in the United States, having first been used in the late 1800's in Illinois, but the surging acceptance of the method is relatively new. The number of longwall installations in this country are nearly doubling annually as this method continues to prove itself as a coal producer's delight terms of operating cost, performance and safety. Since 1951, several longwall installations have been tried in Barnes and Tucker Company operations. Although all efforts actually proved that the system itself could be used in prevailing conditions, it was not until 1967 that a unit was put in use that proved competitive with regular mining equipment, both conventional and Continuous.

Jan 1, 1968

By João F. C. L. Costa, Vanessa C. Koppe, Clayton V. Deutsch, Marcel A. A. Bassani, Pedro H. A. Campos

Blending inevitably occurs to some degree during mining and mineral processing operations. Traditional mine scheduling assumes that all variables average linearly, which allows the calculation of the blended material properties as a linear weighted average. However, metallurgical properties such as metal recovery and Bond Work Index (BWI) are known to average nonlinearly. The nonlinear properties of the blended material can be calculated using nonlinear blending models. A simulated annealing algorithm is developed and applied to a short‐term mining face optimization problem to maximize the total metal recovered considering nonlinear blending. Compared to a standard schedule plan, the optimized one shows relevant improvements in synergistic and antagonistic blending behaviors.

Jun 25, 2023

By Mark R. Bowie

Air-fall tuffs have been altered to zeolite via reaction of volcanic glass with local pore solutions at the six localities discussed in this paper. These are in the southern Basin and Range Province of Arizona and New Mexico, and in the Trans-Pecos and Coastal Plain regions of Texas. Zeolitization occurred in either closed- hydrologic, open-hydrologic, or hydrothermal groundwater systems. The tripping Spring Valley (DSV) chabazite in Arizona and the Buckhorn clinoptilolite in New Mexico originated in a late Cenozoic network of closed-hydrologic, lacustrine basins extending from southeast Arizona into southwest New Mexico. At DSV, two potentially commercial chabazite-rich tuffs are interbedded with lacustine mudstone. The main zeolite tuft contains up to 90 percent chabazite. The upper zeolite tuff averages approximately 67 precent chabazite. At the Buckhorn deposit, two clinoptilolite-rich tuffs are interbedded with lacustrine m udstone in the upper part of the Gila Conglomerate. The lower zeolite tuff contains up to 90 percent clinoptilolite. The upper zeolite tuff contains over 60 percent clinoptilolite. The Casa Piedra clinoptilolite is in the Trans-Pecos region of Texas. It formed during the Tertiary in a closed basin containing a playa lake. The Casa Piedra tuff averages about 60 percent clinoptilolite. Air-fall tuffs of the Cuchillo Negro, New Mexico and Tilden, Texas clinoptilolite deposits were zeolitically altered by either percolating ground waters in open-hydrologic systems or locally by ponded, saline, alkaline solutions. Cuchillo Negro tuffs are Tertiary and average approximately 50 percent clinoptilolite. Clinoptilolite-rich tuffs of Ebcene age have been mined from four quarries at the Tilden deposits. Tufts from the Kuykendall and Buck Martin quarries contain approximately 50 to 60 percent clinoptilolite. Low temperature, SiO2 - rich, hydrothermal solutions altered air-fall tuff to clinoptilolite and chabazite in the Foster Canyon area of the Tertiary Cedar Hills and Seldon Hills volcanic-vent zone in southcentral New Mexico. Poster Canyon tuffs contain up to 60 percent zeolite and average 40 to 50 percent clinoptilolite. The dominant mineral in the zeolite tufts at the six deposits studied is generally microcrystalline and either chabazite or clinoptilolite. Lithic fragments, unaltered volcanic glass, other zeolites, quartz, calcite, opal-CT, cristobalite, feldspar, evaporites, clays, and mafic minerals are also constituents of the tufts.

Jan 1, 1987

By A. Palit, M. K. Mohanty

This investigation has concentrated on optimizing the newly developed Pansep linear screen and developing empirical models to predict the screening performance. Most empirical models developed in the past to predict the performance for industrial screens are suitable for the vibratory screens. Understandably, these models are deficient in predicting the performance of linear screens due to the difference in their operating principle. Thus, the main objective of this study has been to develop empirical models suitable for linear screens to predict the partition coefficient for a given size fraction as a function of the aperture size. The inadequacy of the conventional model equation originally developed for vibratory screen has been demonstrated and a modified equation developed to predict the partition coefficient as a function of the normalized mean particle size (d/d50c). In addition, new model equations have been developed for linear screens to predict the screening efficiency as a function of the separation size(d50) and to predict the separation size as a function of the screen aperture. It is believed that these model equations will be useful for the plant operators in selecting the mesh panels of correct aperture size and in predicting the product size distribution based on the selected aperture size.

Jan 1, 2003

By Kerry J. Stanaway, Thomas E. Garnar

Titanium was discovered in 1791 and, four years later, was named after the Titans of Greek mythology. Titanium metal was first made in 1910, but was not used commercially until the 1950s when it was nick-named The Wonder Metal of the Age. The first titanium dioxide (TiO2) white pigments were produced commercially in 1915; more than 90% of the titanium minerals produced in the world today are used in the manufacture of white pigments. The remaining 10% are used to manufacture titanium metal and other uses such as welding rod fluxes. Titanium mineral mining began in the United States between 1880 and 1900 in Chester County, Pennyslvania. Rutile from a deposit near Roseland, VA, was mined in 1901. The use for the rutile was limited to production of a few titanium chemicals and for coloring ceramics. Larger scale mining for ilmenite, rutile, and zircon began in Florida to provide chemical materials for use in World War I in 1918. This mining ended in 1928. Large scale mining of titanium minerals in Australia began when Benick, Anderson, and Porter (later called Tamco) started mining the beach sands at Yamba in New South Wales in 1935. Ilmenite production from beach sands in the State of Kerala in southwestern India also began in the 1930s. The 1940s saw many changes in titanium mineral mining. Extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec. The Pigments Department of E.I. Du Pont de Nemours & Co. lost their high grade Indian ilmenite supply after World War II began, and they were forced to use lower grade ilmenite from National Lead's (now NL Industries) Sanford Lake Deposit, near Tahawus, NY, in the Adirondack Mountains. At the end of the war, Du Pont undertook an intense search for a domestic ilmenite source. With the cooperation of the US Bureau of Mines, Du Pont geologists found a very large deposit east of Starke, FL, in 1946. In 1948 Du Pont entered into a contract with Humphreys Gold Corp., who operated a heavy minerals mine near Jacksonville, FL, to construct a plant and operate it for a period of ten years. The plant started up in 1949 and operated under Humphreys' management until the contract expired in 1958. Du Pont has operated the plant since that time. In 1956, a second plant was designed and built by Du Pont a few kilometers northeast of the town of Lawtey. The 1960s saw titanium mineral production expand in the southeastern US with Humphreys' contract mining Du Pont's ore body at Folkston, GA. In the early 1970s. American Cyanamid and Union Camp Paper Co. formed a joint venture company, Titanium Enterprises (TE), to mine and separate titanium minerals from Union Camp's ore deposit southwest of Green Cove Springs, FL. In 1975 the TE plant was shutdown and later sold to Associated Minerals (USA), Inc. (AMC), a subsidiary of Renison Goldfields Consolidated Ltd., an Australian company. It now operates under the name RGC (USA). Mineral production grew in the 1970s with the development of extensive heavy mineral deposits at Eneabba in Western Australia and Richards Bay in the Republic of South Africa. The 1980s saw the construction of a very large ilmenite mine and synthetic rutile processing plant in the state of Orissa southwest of Calcutta, India. At the same time, concern for titanium mineral shortages expected by the end of this century, gave rise to a flurry of exploration activity during the mid 1980s. As a result, large deposits were found in Virginia and North Carolina. New deposits were also discovered in Australia. Fig. 1 shows the distribution of world titanium deposits and mines. The world TiO, production capacities are given in Table 1.

Jan 1, 1994