Search Documents

By S. A. Moffatt

For several years iron ore processing plants, located in the northern U.S. experienced seasonal decreases in the grinding efficiency of their primary autogenous mills. Kawatra and Eisele (1992) studied this phenomenon in an operating plant and characterized it in terms of specific energy consumption (Fig. 1) and production of critical size material (Fig. 2). Critical size material is defined as ore that is too small to be effective grinding media and too large to be ground. This data showed that both specific energy consumption and critical size production increased during the winter months. The increased energy consumption was in part a result of an increase in the viscosity of the mill pulp at colder pulp temperatures. However, viscosity could not fully explain the changes in critical size production. These changes are most likely due to changes in the breakage characteristics of the ore. Other studies were also conducted to determine if thermal and physical properties of iron ore changed at colder temperatures. These are summarized below:

Jan 1, 1993

By Jr. Stokowski

Topsoil for revegetation projects is in demand in many urban areas. In this case history, a large aggregate producer manufactured a topsoil from three waste materials. The topsoil was produced in a 200,000 m2 (50-acre) abandoned gravel pit that still had additional gravel under 10 m (30 ft) of overburden uneconomic to strip directly. The topsoil was produced by rotary mixing of sludge, overburden, and a lime admixture; solar drying; and stripping and stockpiling of the product. A major problem was an increase of topsoil drying times for stripping from 40 to over 100 hours when it was rewet by storms. The problem was solved by a research project that evaluated over 50 formulations and over 20 waste materials. . The final formula dried in 15 hours and contained 3-parts sandy mine spoil, 1-part sewage sludge, and 2 % spent-bed, a granular quick-lime produced during power-plant flue-gas desulfurization.

Jan 1, 1988

By B. J. Arnold

Over 600 million tons of coal are handled annually for use by the country's coal-fired power plants. Coal is transported in various ways. overland conveyors. Railcars, trucks, and barges. It can travel short distances or thousands of miles, picking up moisture, freezing, or drying. When the coal is received at the power plant, environmental problems with fugitive dust and further handling problems can arise.

Jan 1, 1989

By M. Irish

This paper describes the emergency water control measures used at Pegasus Gold's Zortman Landusky mine during the September 1986 flood. The amount of solution stored increased by approximately 78 165 m3 due to receiving 0.2134 m of rain in a 24 hour period. Three methods of water disposal will be discussed including continuous chlorination, batch chlorination, and reverse osmosis. A water management program will also be discussed.

Jan 1, 1988

By S. S. Peng

A hybrid boundary element-finite element model was formulated to model roof bolt reinforcement of the roof strata with bedding planes. This model was used to analyze the stress distribution around a rectangular opening with variables such as opening width-height ratio, number of bolts installed, number/location of bedding planes, in-situ stresses, etc. The most critical areas are identified and the number and length of roof bolt required are then determined. Two case examples are illustrated.

Jan 1, 1989

By Richard Keith Corbin

INTRODUCTION With the world media full of predictions that the price of gold will quadruple in three years (Maybury, R.J., 1988), and with financial forecasters and strategists touting opportunities to make 400% in gold (Skousen, M., 1988), explorationists and entrepreneurs are scurrying to find enough gold to feed the global gold fever created. At the same time, gold deposits in the United States and other developed and intermediate countries are becoming less attractive because of environmental restrictions, radical reductions in tax incentives, and depleting reserves, causing people in the mining industry to begin looking at opportunities for foreign investment in gold mining concessions in lesser developed countries (LDCs). Meanwhile, LDCs are responding with chamber-of-commerce aplomb in marketing their opportunities. In the face of all this frenzy and hype, targeting gold mining concessions in LDCs for foreign investment may be done more objectively by employing a systematic approach. For this paper the SHOP rating system (Corbin, R.K., 1987), which considers factors of the LDC's stability, hospitability, ore occurrence, and profitability potential is used. The result is that a tiny banana-growing republic in Central America, first discovered by Columbus and named the "Rich Coast'' because of the many gold adornments worn by its Indians, has been rediscovered and emerges as a classic LDC gold target.

Jan 1, 1988

By T. P. Meloy

Media mills operate by having energy transferred to the media which in turn grinds the feed material in a packed bed. Regardless of the mill type, the media energy density per unit surface area is constant. Since for optimum grinding conditions, both peak pressures and particle number of the bed depth are constant, the frequency of energy input is inversely proportional to feed size. As the particle size decreases the voles energy density increases linearly necessitating cooling in stirred mills. Grinding finer particles therefore, requires moving from rotary to vibratory mills, and the finest, the stirred mills.

Jan 1, 1987

By G. E. Burrer, D. Malhotra, T. E. Irwin, S. Johnson

Climax byproduct-plant tailing assayed 0.019% WO3. Pilot-plant and laboratory tests were performed to investigate the possibility of recovering additional tungsten values from the byproduct-plant tailing. The methodology used in the study and the results of this investigation are discussed.

Jan 1, 1987

By B. T. Dawson

In today's work world, constant changes are a fact of life. Downsizing and technological advances are two of the most prominent concerns for employers and employees alike. In this article, the author addresses some of the emotional consequences of these changes and offers a new, empowering perspective for coping with them.

Jan 1, 1998

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By F. W. Pereira

The Montana Talc ore body was discovered in the summer of 1983, in the Gravelly Range, approximately 25 miles south of Ennis, Montana. Initial drilling indicated a plus-million-ton ore body of high-purity talc. Preliminary analyses were performed on the ore cuttings, .including chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. The results indicated the talc was similar to that currently being marketed from Montana and probably would have good commercial value.

Jan 1, 1989

By H. L. Ehrlich

Marine manganese nodules harbor a mixed population of manganese-oxidizing and -reducing bacteria, as well as bacteria that do not act on manganese. They also host phagotrophic protozoa. Out of several laboratory studies, one line of investigation indicates that some kinds of bacteria found on nodules can catalyze the oxidation of Mn2+ bound to Mn(IV) oxide at the surface of nodules at in situ temperature and pressure. In the absence of appropriate bacteria, the rate of oxidation of the surface-bound Mn2+ is significantly slower. How Fe(III) is incorporated is still unclear. Base metals such as Cu, Ni and Co, which are usually found in marine nodules in various quantities, may be incorporated through scavenging by Mn(IV) oxide. Laboratory evidence shows that some other bacteria on nodules can reduce the Mn(IV) oxide to Mn2+ in the presence of an appropriate source of reducing power in the form of organic carbon. The reduction of Mn(IV) oxide mobilizes manganese and trace metals such as Cu, Ni, and Co in the nodules. These bacteria reduce Mn(IV) whether oxygen is present or not. They could be harnessed in the bioleaching of nodules. The manganese(IV)-reducing bacteria and the bacteria that neither oxidize nor reduce manganese are thought to keep the organic matter in the nodule environment sufficiently low to favor bacterial manganese-oxidation, which in laboratory tests is inhibited by excess organic carbon. The preying by the protozoa on the different kinds of bacteria is thought to control the bacterial population on nodules and ensure continued growth of the manganese-oxidizing bacteria and the nodules. To eliminate interference from seawater salts in the bioleaching of Mn, Cu, Ni and Co, it may be more advantageous to use terrestrial Mn(IV)-reducing bacteria than the Mn(IV)-reducing bacteria resident on nodules. The terrestrial bacteria would allow bioleaching in fresh water. Unlike the marine bacteria, most terrestrial bacteria studied to date reduce Mn(IV) oxide only anaerobically. A general outline for an anaerobic bioleach process of marine nodules with freshwater bacteria is discussed.

Jan 1, 2000

By S. McMurray

INTRODUCTION Towards the end of the 1890s the attention of a prospector by the name of Thomas Cullinan was drawn to the occurrence of alluvial diamonds east of Pretoria. Persistent prospecting work by Cullinan led to the loca¬tion of the source of these diamonds-a kimberlite pipe on the Elandsfontein farm. Cullinan eventually acquired the property in 1902, and during an extensive evaluation program outlined the largest diamondiferous pipe in South Africa on which the Premier mine was established. Worldwide attention was drawn to this mine in 1905 when the Cullinan diamond, which weighed 3106 carats and is by far the largest gem diamond ever discovered, was recovered. Premier mine operated with varying success until 1932 when the worldwide depression forced it to close. In 1945 the mine was reopened and since then has been a major producer of gem and industrial diamonds. During the early 1950s exploratory drilling revealed that below the 370-m level the pipe had been completely cut off by a younger gabbro sill. This sill has created major mining and metallurgical problems but the existence of vast reserves of high grade ore below it justi¬fied the establishment of virtually a new mine below the sill. Detailed planning of below-the-sill mining is nearing completion and the development of the first mining block (the L1 block) is well advanced. A full discus¬sion of this block follows. GEOLOGY OF PREMIER MINE Pipe Morphology and Country-Rock Geology As can be seen in Fig. 1, Premier mine is an elon¬gated oval shape with a long axis of 900 m on the surface and a short axis of 450 m. The pipe has a surface area of 32 hectares which decreases progres¬sively with increasing depth, so that 500 m below the surface the area is reduced to 22 hectares. The contact between the kimberlite and the surrounding country rock is sharp, with an average angle of dip of 1.48 rad (85°). From the surface down to approximately 350 m, the country rock is a felsite which grades downwards into a norite. In general both rock types are hard and massive, the felsite in particular being poorly jointed. This characteristic combined with other factors results in an extremely stable open pit, and near-vertical side¬walls are currently being maintained. The norite in general is competent but is heavily jointed in some areas resulting in very blocky ground which creates localized tunnel support problems. In the southeastern area below the sill a zone of highly altered and very unstable norite, which has also created localized sup¬port and development difficulties, lies adjacent to the pipe contact. Kimberlite Geology The Premier pipe is a complex multiple intrusion which contains in the region of 15 separate types of kimberlite, most of which are volumetrically insignifi¬cant. On a simplified basis three major types can be identified which correspond to three separate phases of intrusion. They are: Brown Kimberlite: This represents the first phase of intrusion and now occupies the eastern part of the pipe. In plan the brown kimberlite has a crescentric shape resulting from the intrusive relationship with the younger gray kimberlite which lies to the west. The brown kimberlite increases in relative area with increas¬ing depth which is a favorable factor for future mining operations since this kimberlite is the richest area of the mine, having an average grade of 70 carats/ 100 t. Below the sill this rock disintegrates extremely rapidly when exposed to air or water, to form a fine gravel-like material. This characteristic is due to a high montmorilonite clay content. As is common with clay minerals of this type, water can be absorbed into the crystal lattice with a resultant increase in volume which causes the physical decomposition of the rock. The presence of this decomposing kimberlite was a major factor governing the choice of a mining method, as well as development and tunnel support techniques. Gray Kimberlite: This is the most abundant type and represents the second major phase of intrusion. The diamond content is variable depending on the amount of waste rock dilution, and in general the rock is stable and non-decomposing. At the time of formation of Premier, the surface rock type was Waterberg quartzite, a rock formation which has subsequently been removed from this area by erosion. The explosive extrusion of the gray kimberlite caused extensive brecciation of this rock and while the kimberlite was in a mobile state huge masses of quartz¬ite, amounting to tens of millions of tons, slumped into the pipe. This quartzite became concentrated in the central area of the mine and has been a major mining problem throughout the history of Premier since, due to the irregular distribution of the quartzite, effective selective mining has never been possible. The quartzite is therefore extracted with the ore and has a significant dilution effect on the overall grade. Black Kimberlite: In the western part of the pipe a circular, pluglike body of kimberlite is intruded into the gray kimberlite. This plug consists mainly of a hard, dark-colored rock known as black kimberlite, but also contains a number of minor kimberlite variet.ies as well as nonkimberlite carbonate dikes. The Gabbro Sill The sill averages 75 m in thickness and within the confines of the pipe consists of 52 million t of rock. On average the major dip is 0.34 rad (20°) to the northeast which is across the short axis of the pipe, the range of dip being from near horizontal up to 0.52 rad (30°). Due to the pronounced dip, the sill is encount¬ered over a vertical distance of 175 m with the highest upper contacts on the 355-m horizon and the lowest bottom contact on the 530-m horizon.

Jan 1, 1982

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

5.1 INTRODUCTION There are several types of surface ground disturbances, each of which is immediately transmitted to surface structures and causes damage of various forms, depending on the location of the structures in the subsidence basin. Many criteria have also been proposed for defining the potential structural damage. All of these topics will be discussed in this chapter. 5.2 TYPES OF GROUND DAMAGES There are two types of ground damage, continuous and dis¬continuous, that could inflict damages to surface structures. Dis¬continuous ground damage is open fractures of various degrees. Four types of fractures are commonly seen (Brauner, 1973b): 1. Fissures or cracks. Cracks are the most common form of ground damage and range from completely closed to several feet wide. Surface cracks are most prominent when the ratio of mining depth to mining height is smaller than 30 to 50 times mining height. Cracks initiate parallel to, but ahead of the moving long¬wall face at some intervals when the depth-to-mining height ratio is less than 25 to 30. As the face continues to move, they open up and then close gradually, and in most cases eventually close up completely when the face moves farther away. Sometimes when the depth-to-mining height ratio is larger, cracks may initiate be¬hind the face and go through the same cycle. Cracks are also more likely to occur in the hill when the face is moving in the uphill direction. Cracks also occur at or near both sides of the panel edges. Those cracks tend to remain open permanently. When the surface is covered with grass or other vegetation, cracks of less than 1 to 2 in. wide usually do not penetrate it and become invisible on the surface. 2. Steps. A step may occur when the longwall face stops abruptly if the mining depth-to-mining height ratio is less than 20. Steps may also occur along the panel edges. Steps also range from a few inches to a few feet in width and depth. If planes of weakness are oriented favorably, ground will slide along these planes and form steps on the surface. 3. Cave-in pits. These result from local collapse of the ground from the mine level to the surface when the mining depth is less than 150 ft and occur mostly above abandoned mined lands. They may be as large as 40 ft wide and deep. 4. Bumps (compression ridges). Bumps result from ground compression and occur mostly near panel center some time after mining. Bumps of up to 4 ft, but mostly 1 to 2 ft, have been identified. Continuous ground damage refers to the formation of the sub¬sidence basin where continuous nondestructive ground deforma¬tions occur. As mentioned earlier, continuous ground deforma¬tions associated with a subsidence basin include subsidence, slope, curvature, displacement, horizontal strain, twisting, and shearing. 5.3 TYPES OF SURFACE STRUCTURAL DAMAGES Both continuous and discontinuous ground disturbance cause damage to surface structures. A. Structural Damages Due to Discontinuous Ground Disturbance 1. Fissures or cracks. Open cracks can cause dislocation of surface structure if the gaps are sufficiently large so that the struc¬tural elements cannot resist but fail. On the other hand, minor cracks affect only the appearance, and not the structural integrity. 2. Steps. When a surface structure is located on a step, some portions of the structure lose support and become overhung. In the case of a residential house, there will likely be many open frac¬tures in the overhung portions, followed in severe cases by sepa¬ration of the superstructure at the edge of the step. 3. Cave-in pits. If the caved-in pit is larger than the surface structure, the structure will drop into the pit and become unstable. If the caved-in pit is smaller than the surface structure, the struc¬ture may either become overhung or lose support in some portions. In either case, it is unsafe for use. 4. Bumps (compression ridges). Bumps will disrupt roadways or house floor. If located under supporting members of the struc¬tures, it may cause damages. B. Structural Damage Due to Continuous Ground Disturbances 1. Subsidence. Pure subsidence or uniform subsidence over an area does not cause any structural damage. However, if it becomes a topographical low area, it may be flooded with water and make the surface structures unusable. It must be noted that the flat bottom area at the center of the final supercritical subsidence basin does not reach that position suddenly. Rather, as shown in Fig. 3.1, it is subjected to the dynamic surface deformation asso¬ciated with the traveling subsidence basin before it is left behind to be part of the flat-bottom area. Therefore any structure located at the center of the final supercritical subsidence basin must be able to resist the dynamic surface deformation in order not to be dam¬aged. 2. Slope. Ground slope will induce tilting of the structure. Tall structures with small base areas, such as water towers, chimneys, and power transmission towers are most sensitive to ground slope. If the ground slope is such that if after tilting the center of the gravity of the tilted structure falls outside the base area, it will topple, but this seldom occurs. Ground slope will change the designed slope of a buried trans¬portation pipeline, either increasing or decreasing the original slope depending on whether the ground slope coincides with or opposes the original slope. There are maximum allowable final slopes for various types of transporting materials. Ground slope also affects highways and railways. There is a maximum allowable final slope for a railway because tractive effort increases 1/1000 of its weight for every increase of 1/1000 in grade. 3. Curvature. There are positive (convex) and negative (con¬cave) curvatures. When a surface structure is located on a positive curvature, both ends become unsupported, followed by bending upward at the midportion. The top portion is subjected to more severe stretching than the lower one. As a result, vertical cracks with a wider gap at the top occur at the window, door frames, on the walls, and at -the wall joints. V-shaped cracks appear at the

Jan 1, 1992

By Mark L. Blanford, Roger M. Zimmerman

INTRODUCTION Volcanic tuffs on and adjacent to the Nevada Test Site (NTS) are being considered by the Department of Energy (DOE) for the possible geo- logic disposal of high-level radioactive wastes. The Nevada Nuclear Waste Storage Investigations (NNWSI) project was established in 1977 to evaluate such disposal. Sandia National Laboratories (SNL), one of the participants in the NNWSI project, has as one of its responsibilities the development of a rock mechanics program for the Nevada site. SNL conducted three small-diameter heater experiments in welded and nonwelded tuffs in G-Tunnel on the NTS, to investigate the thermal (heat transfer) and hydrothermal (thermal- induced water migration) behavior as part of the rock mechanics program. These two aspects were investigated to increase knowledge about the behavior of tuff so that predictive capabilities are available for use by repository designers, waste-package designers, and performance analysts. Also, knowledge of the behavior of the tuff is invaluable for planning and designing future in situ experiments at Yucca Mountain, the candidate site for the repository. The evaluations of these three experiments is the subject of this paper. Designers, analysts, and experimenters are seeking a better understanding of the behavior of tuffs under the influence of thermal loads expected from radioactive-waste storage, because of two physical features peculiar to tuffs. First, tuffs are inherently porous because of the manner in which they are deposited (Smith, 1960). Tuffs utilized in G-Tunnel testing have porosities ranging from 15 to 46%, which cover the ranges of expected porosities in the target horizon at Yucca Mountain. It has been established that the G-Tunnel tuffs have similar bulk, thermal, and mechanical material properties to those at Yucca Mountain (Zimmerman et al., 1984), thus, G-Tunnel testing can be used to evaluate the effects of porosity on the thermal and mechanical behavior. The second feature is that tuffs above the water table contain pore water that influences the thermal properties of the rock; displacement of the water must be accounted for in repository designs and analyses. For example, G-Tunnel tuffs, located some 600 m above the static water level, have saturations in excess of 60%. Similar percentages are expected at the target horizon in Yucca Mountain (Zimmerman et al., 1984). The presence of and the removal of the pore water affects the thermal behavior of the tuffs, and these three experiments were designed first to determine the phenomenological behavior and then assess influences on predictive capabilities. The focus in this paper is to present the results and evaluations of the experiments as they apply to improving predictive capabilities. The thermal aspects are emphasized by comparing the measured temperatures (in and around heater emplacement holes) with calculations of predicted temperatures using numerical models, so that the effects of significant parameters can be evaluated and integrated into future predictive models. Observation of the hydrothermal aspects is needed to assess the effects of loss of pore water and subsequent migrations on the temperature fields during the heating, and also to define the expected environment in the vicinity of the outer metallic surface around the waste. The metallic boundary can be either the outer shell of the waste package system, which is the main engineered barrier for waste containment, or the borehole liner. A final decision has not been made as yet about the necessity for lining boreholes; thus, the emphasis is on predicting the characteristics of the environment around the outer metallic surface. Two aspects that limit the scope of this paper are (1) the experiments were performed at a smaller than canister scale for the purpose of

Jan 1, 1986

By W. A. Haley

The use of diesel engines in underground hard-rock mines dates back to the late 1940s. For the first several years, they were used only occasionally, being limited to a few metal mines that experimented with crawler¬mounted front-end loaders, tractor-trailer hauling units, a few tractors for drill-compressor mounts, and utility cleanup machines. By the mid-1950s, track loaders had become commonplace in limestone mines and uranium mines on the Colorado Plateau in the United States, as well as in Canada. Use of crawler-mounted tractors as drill and compressor mounts also increased. By the end of the 1950s, rubber-tired loaders and some haulers began to replace the track-type machines and rail-mounted cars that had been in use. About 1960, the rubber-tired machines brought about a new era of underground mining mobility and flexibility, centered on a method commonly known as "trackless mining." Ultimately, many of the underground rail-type systems for loading and hauling were replaced by the trackless mining technique. ECONOMIC CONSIDERATIONS The size and nature of mineral deposits, plus ground control techniques, historically had dictated small open¬ings to the surface from many underground mines. The small mine openings led to the development of special rubber-tired loaders and haulers designed specifically for access through the small openings. However, some mines, particularly those in massive mineral deposits, are able to excavate and maintain very large openings, and some use modified room-and-pillar systems. With the large mine openings, the use of larger, more produc¬tive equipment such as that commonly found in surface mining becomes economical. In fact, productivity gen¬erally increases at a more pronounced rate than machine size increases because many of the larger machines were designed for heavy-duty shot-rock applications in surface mines and construction sites where the handling of blasted rock is common. Table 1 can be used as a very Table 1. General Productivity Comparison for Conventional Machines In Underground Use (Shot-Rock Conditions) 2.3 m3 (3 cu yd) 4.6 m3 (6 cu yd) Loader Loader Expected Surface 230 t/h 540 t/h Production (250 stph) (600 stph) Expected Underground 90 t/h 270 t/h Production (100 stph) (300 stph) Expected Total Efficiency: Surface 40%-60% 50%75% Underground 25%.-40% 30%50% Expected Useful Machine 8000 hr 12,000 hr Life Before Replacement general comparison of the production and efficiency between small and large machines. Combining greater productivity often inherent in larger machines, with reduced downtime resulting from using fully developed machines with fast parts and service backup, some mine operators have been able to reduce material handling costs appreciably while reduc¬ing manpower requirements for operators and main¬tenance men. Large mine openings increase the amount of rock that must be handled in the development work, and they sometimes increase the dilution in stopes or rooms, de¬pending upon the dimensions of the ore zone. Providing adequate space for the unrestricted operation of large surface mining machines could, therefore, lead to more waste segregation and handling costs. It could also cause greater ore dilution that would result in a lower grade of ore being delivered to the processing plant. The tradeoffs between opposing cost factors must be reconciled and balanced to achieve the best overall cost of the crude ore, concentrates, or product. EQUIPMENT MODIFICATIONS Loaders and haulers designed for surface mining are seldom used underground in their standard con¬figurations without some modifications. If done, the modifications generally are made by the equipment dealer and/or the user, and the modifications usually include one or more of the following items: 1) The exhaust stack is lowered, and its direction is changed. Usually, it is repositioned horizontally to the rear, or it is fed into the engine fan to diffuse the exhaust gases. 2) The operator's position is lowered by either lowering the seat or changing the seat to a side mount. 3) The operator controls are adjusted to fit the new operator position. 4) Other components, such as the radiator and loader tower, are lowered. 5) Special bumper guards are mounted at the base of the radiator area. 6) An exhaust conditioner is mounted and con¬nected, using either a catalytic or a water-type condi¬tioner, or both. This usually is controlled by the safety and health regulatory authority having jurisdiction. 7) The positions of other components are rearranged

Jan 1, 1982

By R. L. King

An expert system is a computer system that performs tasks that are considered by most people to require human expertise. Since their functioning relies heavily on large bodies of knowledge, they are often referred to as knowledge-based systems. These systems can contain the skill and knowledge of an individual human expert or the combined knowledge of a group of experts. The knowledge embodied in an expert system can consist of specific facts, HSHA regulations, heuristics or rules-of-thumb used by the expert, and databases. The purpose of this paper will be to introduce the participants in the ?Increase Competitiveness Thru Innovation? session to expert systems. This introduction will enable the participants to better appreciate the balance of the papers to be presented in this session. These papers will deal with specific mining problems and a proposed innovative solution. This paper will discuss such topics as problem-solving paradigms, rules of inference, knowledge representation, and the structure of expert systems.

Jan 1, 1989

By Raymond Sandiford, Taehyun Moon

"In 2012, Superstorm Sandy (Sandy) caused extensive flooding in many of the tunnels in New York City. The inundation resulted in two distinct stress changes to the tunnel structures. The first stress change was water pressure on the inside face of the tunnel lining. The second condition related to the change in buoyancy of the tunnels. In areas where the tunnels were supported on rock and an adjoining area supported on soft soil, overstress issues arose. Numerical analyses were performed to assess the structural impacts of the tunnel water inundation; especially stress changes due to internal pressure as well as changes resulting from the buoyancy effects. The paper will discuss the assessment process and its results; it will demonstrate that the change in internal pressure were of little consequence, however the change in buoyancy resulted in significant increases in bolt stresses. INTRODUCTION Superstorm Sandy caused tens of billions of dollars in damage in the NYC metropolitan area. It also caused significant disruption to the transportation system by flooding most of the under river tunnels servicing Manhattan from the outer boroughs and New Jersey. The rehabilitation of the tunnels was of paramount importance to the restoration of the NY and NJ economies. With this rapid restoration, it was essential to determine whether the flooding of these tunnels caused damage to tunnel structures. A series of analyses were undertaken to ascertain whether the change in the stress conditions and buoyancy of the tunnels, due to the flooding, was significant enough to cause damage or over-stressing of the tunnel components. The effects of this unforeseen loading condition was a concern to the agencies operating these tunnels and were thus analyzed to ascertain if there were any adverse impacts. This was a concern because the majority of under river tunnels in NYC was built earlier in the century and constructed using bolted cast-iron lining segments. The cast iron, although quite strong in compression, is much less so in tension. Also, after nearly a century of use, the bolts connecting these segments together have under gone varying degrees of corrosion. The stress changes in both the liner segments and the supporting bolts were estimated for conservative ground support conditions to provide confidence that the flooding had not caused permanent damage."

Jan 1, 2016

By John C. Edwards, Robert C. Bates

Modeling uranium mine radiation control methods and natural environmental radon variations is an extremely complex endeavor. A number of authors have examined particular facets of the problem and have proposed models for their area of interest. Bureau of Mines personnel brought together many of these individual studies, and from them have attempted to develop a coordinated plan for modeling radon daughter concentrations in the uranium mine environment. This approach is described.

Jan 1, 1981

By C. J. Hall

The simplest natural ventilation cycle is similar to a Joule or Brayton cycle. This comprises two reversible adiabatic processes in the shafts and constant pressure processes underground and on surface. The thermal efficiency of such a cycle is given by the temperature increase in the downcast shaft divided by the absolute temperature of the air at the bottom of the downcast shaft, and is independent of the temperature increase underground. This efficiency is comparable to the Carnot efficiency, which is the greatest possible value between constant temperature reservoirs, source and sink. Two variations of the Joule cycle are investigated, using numerous work examples. In the first, dry air is used as the working substance, a fan is provided at the top of the upcast shaft, and various mass rates of flow are used with frictionless shafts and a constant resistance value in the horizontal mine workings. The lost work less the fan work gives the natural ventilation work, and this divided by the enthalpy increase in the workings gives the thermal efficiency. The thermal efficiency increases dramatically with mass rate of flow, although the enthalpy increase remains constant. This appears to violate the second law of thermodynamics, since the frictionless case has a Carnot efficiency. When the lost work is added to the enthalpy increase, however, the efficiency decreases slightly from the Carnot value, to conform with the second law. This increase in efficiency with mass rate of flow is often referred to as the reheat effect, although the air is not heated. The second investigation is similar to the first, except that the air entering the downcast shaft contains a small amount of water vapor, and there is evaporation in the mine workings only, until the air entering the upcast shaft is saturated. There is, of course, condensation in the upcast shaft. In this case, it is not possible to calculate the Carnot efficiency, but the thermal efficiency is 20 to 40% of the similar dry air values. This decrease is much more than can be accounted for by the larger value of specific heat for water vapor. In addition, the natural ventilation work is almost constant with increased mass rate of flow, and the thermal efficiency based on heat addition tends to decrease. The thermal efficiency based on heat and lost work decreases in conformity with the second law. The reasons for the differences in behavior between dry and moist air are not readily apparent.

Jan 1, 1991