Search Documents

The Colorado portion of the Rio Grande rift is clearly defined physiographically from the south in the San Luis valley northward to the latitude of Leadville where sediments of the Dry Union Formation (Tweto, 1961) accumulated within the subsiding rift zone. To the north of Leadville is a system of faults active in the late Tertiary, including the Mosquito fault that offset a portion of the Climax mineralization (Wallace et al., 1968). Tweto (197B) describes remnants of Dry Union Formation against the Mosquito fault north of Dillon in the Blue River valley, so it is apparent that the rift and associated sediments extended well to the north of Leadville. Kelley (1952, 1954, 1956) and Chapin (1971) have noted in New Mexico that the Rio Grande rift is a series of en echelon basins, offset to the east, with constrictions connecting them (Fig. 1). In Colorado the structural basins are offset to the west. The net effect of all the rift zone basins in New Mexico and Colorado is an arcuate pattern (Fig. 1) abutting the Colorado Plateau and Sari Juan Volcanic Province on the west. The width of the rift system gradually decreases northward to about Leadville where rift definition is not apparent.

Jan 1, 1987

By H. J. Bickel

This paper is concerned with general concepts and statistical devices used in projecting overall energy requirements. Particular emphasis is given to the use of individual end- use markets as an approach to developing future overall energy requirements, and translating these requirements into fuel consumption.

Jan 1, 1962

By A. Noble

"Linear circuit analysis (LCA) is a fundamental tool that may be used to evaluate, design and improve the performance of mineral separation. The traditional LCA methodology provides a comparative evaluation of circuit designs purely from the unit interconnections. The quantitative approach uses the analytical circuit solution to evaluate the slope of the circuit’s partition curve at the midpoint. Since the partition slope is often associated with a separation’s general selectivity, this numeric value is used to compare and rank alternative configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. By itself, this value does not account for the relatively high unit dollar value of pure material or the gains and losses in mass yield associated with alternative circuit configurations. Realizing the value in the LCA methodology, but respecting the limitations of the partition slope valuation, the authors have derived two new performance indicators that quantitatively address pure particle misplacement (the Partition Moment of Inertia) and circuit mass yield (the Yield Score). Together, these parameters provide a better indication of separation economics in typical mineral and coal separation systems. Since the two parameters provide independent information on circuit selectivity and circuit yield, a Pareto efficiency, multi-objective function selection approach is proposed for preliminary circuit selection.IntroductionOver the past 30 years, numerous scientific and industrial studies have proposed various mineral processing circuit design methodologies that attempt to optimize the allocation of separation resources within the processing plant. Over this period, the methodologies have undergone various transitions, including the increased inclusion of process models and computationally intensive algorithms, as well as a general shift from a purely technical solution (Lauder and McKee, 1986) to partially economic solutions (Abu-Ali and Sabour, 2003; Cisternas et al., 2014). Today, circuit design is largely driven by flowsheet simulation; however, no consistent design methodology is used across the industry.One intriguing approach for circuit evaluation is linear circuit analysis (Meloy, 1983a). This method evaluates the separation potential of the circuit solely considering the unit configuration and stream interconnections. No preliminary data other than the basic circuit configuration is required to use the approach."

Jan 1, 2015

By Thomas C. Shapiro

Introduction In recent years - even months - the number of articles on computers has increased rapidly. One can hardly pick up a newspaper or magazine without seeing a computer-related article. The article usually explains how the computer will change our lives. Many of us have some concern about the nature and type of change. For most of us, though, the problem is lack of information and understanding about how computers work. In other words, how do we make cost-effective decisions about computers? This three-part series will explain, simply, what a microcomputer is, how it works, and how to decide if you need one. This first article will define terms and briefly discuss areas where computerization might be economic. The second article will discuss geology and mining applications. The third article will discuss plant, administrative, and geotechnical areas as well as the future of software development in the minerals industry. Terms and Concepts All computers have input and output devices and a central processing unit (CPU). Information - instructions and data - is communicated to the computer by means of input devices. These instructions to the computer are converted into language that the computer understands. This causes the instructions to be carried out in the CPU. The result of these operations is translated back into language that we understand. This information is then sent to output devices such as printers and video display tubes. Traditionally, peripherals were devices separate from the main-frame (the CPU and memory) and were used to input, output, and store information or instructions. Today, peripherals perform the same functions though they may be housed in the same cabinet as the CPU and memory. Historically, peripherals included all input and output devices not part of the mainframe. Input devices include keyboards, magnetic tape, and card readers. Tapes and disks are input as well as output devices. Output devices are printers, CRTs (Cathode Ray Tubes), and any mass storage device capable of storing data when directed to do so by the computer or the program. In fact, any mass storage device that can give the computer data when requested is an input device. Mass storage devices include floppy disks (thin, round sheets of plastic covered by metal particles), and hard disks. The latter are thicker and more densely coated with metal particles. This allows much more information to be stored. Another type of mass storage is magnetic tape. Its type and size varies widely. Processing and Storage Any computer understanding must include how instructions and data are processed and stored. Information is stored as a positive or a negative field known as a "bit." There are eight bits in a byte. The bits can be represented as either a one or a zero. Thus the code for a byte representing the numeral one is 00110001. The byte representing the letter A is 01000001. These codes are from the American Standard Code for Information Interchange (ASCII). ASCII defines the standard set of characters including alpha, numeric, and special characters. The computer's memory has allocated locations where instructions as well as incoming information can be stored. All information and instructions are stored as binary numbers bit by bit - zeros and ones. The amount of data that can be stored is referred to as either thousands or millions of bits or bytes. The letter "K" is used to designate one thousand units. The letter "M" is used to mean one millon units (one meg). Disks Thus, a 113-mm (5 1/4-in.) floppy disk - double sided and double density (DSDD) - contains 320,000 bytes (characters) or 320K. This is about 164 double-spaced, type-

Jan 2, 1984

By Robin J. Hickson

El Abra has mining concessions granting the right to exploit minerals in more than 130 km2 (32,122 acres). SCM El Abra owns “rights to occupy” the surface of these claims. The company also owns the surface rights over the process plant area and over land conveyor route. The project has procured all material easements relating to the mine area, processing facilities and access rights of way. Engineering, procurement and construction Figure 1 sets out the development and construction schedule for the project. Development is already well under way. As of early January 1996, about 70% of the project was complete and more than 80% of the capital expenditures were committed.

Jan 1, 1996

By D. Dodgen, L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million tom of ash, boiler slag and FGD (flue gas desulfurization - "scrubber") materials as by-products. Utilities and others who bum coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Feb 24, 1997

By Peter W. Lipman

Structural and topographic relief in the Sangre de Cristo Mountains of northern New Mexico provides a remarkable cross section through the recently recognized 23-26 m.y.-old Questa caldera and cogenetic volcanic and plutonic rocks. Although largely eroded, remnants of an ash-flow sheet of silicic-alkalic rhyolite and associated more mafic lavas of the Latir volcanic field are preserved as far as 45 km beyond the source caldera. Within the caldera, the tuff ponded to a thickness of 2-3 km and enclosed chaotic megabreccia fragments which slumped from the caldera walls. At the time of ash-flow eruption, the volcanic field was severely deformed along northwest-trending faults related to the Miocene Rio Grande rift, with most intense deformation occurring within the caldera. Strata were steeply tilted and locally overturned along presumably listric faults. Ash- flow tuffs locally underwent secondary flowage over concurrently developing fault scarps and accumulated within structural basins as rheoignimbritic lava flows. Cogenetic batholithic granitic rocks, exposed over an area of 20 x 35 km, range from mesozonal quartz monzonite to epizonal porphyritic granite and aplite, with the shallower and more silicic phases most abundant within the caldera. Compositionally and texturally distinct granitic phases define a highly evolved resurgent intrusion within the caldera, an incomplete ring dike along its southern margin, and a large mass of less fractionated quartz monzonite south of the caldera. A negative Bouguer gravity anomaly is closely confined to the area of ex- posed granitic rocks; it also reflects boundaries of the Questa caldera. The gravity anomaly is interpreted as defining the extent of the underlying batholith, emplaced into lower parts of the volcanic sequence and underlying Precambrian rocks. Paleomagnetic determinations indicate that the granitic rocks were above Curie temperatures at the time of caldera formation and regional listric faulting, yet most are little different in radiometric age from the intensely deformed volcanic rocks. These relations indicate that the batholithic complex represents the source magma body for the volcanic rocks, into which the Questa caldera collapsed, and was largely liquid at the time of regional tectonic disruption. Compositions of the volcanic and plutonic phases changed from early calc-alkaline metaluminous rocks, to weakly peralkaline silicic rhyolite and equivalent afredsonite-acmite granite at the time of the caldera formation, then back to post- caldera calc-riebeckite granitic rocks. Maximum concentrations of alkalis and minor elements such as Rb, Th, U, Nb, Zr, and Y were reached at the time the caldera formed about 25-26 m.y. ago, but the major molybdenum mineralization of the Questa district took place when the late calc-alkaline granitic ring intrusions were emplaced about 23 m.y. ago, along the south margin of the caldera.

Jan 1, 2013

By A. M. Anthony, A. Y. Atta, S. S. Magaji, U. Abubakar-Zaria

There are two major gold recovery methods: the hydrometallurgical technique, which employs cyanide solutions, and amalgamation method, which involves mercury (Hg). These methods present considerable health, safety, and environmental concerns. Past applications of alpha-cyclodextrin (α-CD) on gold scraps show that α-CD is not only inexpensive, but is also environmentally friendly. This research work used α-CD to recover gold from gold ores instead of gold scraps. The gold ore was sourced from Shanono gold deposit site Kano State,Nigeria. The gold ore was characterized by fire assay (FA) for the precious metal. The concentrate was digested with aqua regia (AR) for 24 h. Modified AR, where hydrochloric acid was replaced with hydrobromic acid, was used for the gold digestion due to the good match in molecular recognition between gold bromide ion (AuBr)− and α- CD in a second sphere coordination complex. The digestate was characterized using atomic absorption spectroscopy (AAS). Gold recovery using this technique is pH sensitive, and five pH values (2.0, 3.6, 4.0, 5.4, and 6.0) were investigated. FA analysis showed the Shanono gold ore deposit contains an average of 4.71 ppm of gold, AAS analysis showed highest gold recovery of 69% at pH 4.0, which is lower than recoveries from the metal scraps. This could be due to the presence of other gangue minerals closely associated with the ore. However, gold recovery using α-CD on Shanono gold ore has shown to have a higher yield of 69% compared to 35.5% yield obtainable by Artisan Small Scale Miners using mercury.

May 5, 2020

By K. K. Bhattacharyya

Vast deposits of lignite occur in the Gulf Coast states and northern plain states. Lignite resources are cited to be over 43 billion tons in the Gulf Coast states. An additional resource of 16 billion tons are reported in North Dakota (Jackson, Smith, 1981). All lignite in the U.S. is mined at present by the open pit method. Draglines and scrapers are primarily used to remove the overburden. Bucket-wheel excavators are also being considered for new mines in the planning stages. Lignite seams are mined using front-end loaders, shovels and trucks, or Easi-miners. The depositional environment of lignite is weak sedimentary soils and rock. Ground water is often encountered within the mining depth. Surface water resulting from heavy rainfall or snow melt contributes to the problems of mining. Mining depths of up to 60 m (200 ft) are under consideration. Draglines exert additional loads on the highwalls and spoil piles. The combination of any number of these factors may cause instability of the slopes. Bearing pressure, trafficability, and settlement can also be a problem for excavation and loading equipment.

Jan 1, 1982

By M. Pillay

INTRODUCTION Heat stress continues to be a safety concern in underground mining. This is due to a number of reasons including increasing depths of mining, increased levels of heat generated from machines, ventilation systems being constrained from providing suitable levels of airflow and others. In order to assess if a thermal environment is safe for miners under normal or modified work arrangements, or to specify stop work conditions a heat stress index is used to guide decisions. Historically, a number of heat stress indices have been developed and applied in underground mines. These can be classed under three broad headings; single measurement, empirically based and rational indices. Do any of these indices perform better than the others? Which one allows simple determinations and decisions to be made in the mine? This paper aims to provide answers to these questions by comparing and contrasting three indices; effective temperature (ET), simple air cooling power (ACP) and Thermal work limit (TWL) for a range of typical mining wet and dry bulb combinations? The paper concludes with the identification of areas for future research. BACKGROUND Heat stress causes discomfort, increases physiological strain, decreases productivity and performance, and contributes to increased incidents [1]. Effective management and control of heat stress is particularly important in mining where hot working conditions are very common [2]. Heat stress index is a common indicator that is used by mine safety advisors and managers to guide decisions about safe work practices in mining under normal or modified conditions. According to Howes and Nixon [3] A safe heat stress control strategy for an underground mine has three elements: • Application of an environmental measure which reflects physiological strain with sufficient accuracy for the range of conditions encountered underground. • Acceptance of a functional relationship between the environmental measure and human performance which is used to optimise the environmental conditions achievable with either ventilation or ventilation and refrigeration. • A management control strategy based on the environmental measure which is designed to ensure that work in environments where excessive physiological strain may occur is prevented and corrective action is initiated. The link between these elements is an environmental measure that reflects the physiological strain a worker is subjected to. Since the turn of the twentieth century various indices of thermal stress have been developed (McPherson [4], Howes and Nixon [3], Brake [5]). In selecting a suitable environmental measure or index one problem that must be addressed is the ease with which it can be physically obtained relative to it accurately reflecting the physiological strain. No index can be universally applied and there is no single correct measure or index. However if an index has provided adequate control in a particular circumstance, then it can be regarded as correct for that situation.

Jan 1, 2019

By Lim Thi Duong, Du Duy Bui, Thuat Ngoc Pham, Chuc Ngoc Pham, Que Anh Nguyen, Hoa Anh Bui, Chi Thi Ha Nguyen, Hoan Thanh Nguyen, Bac Quang Nguyen, Kien Trung Nguyen, Dung Trung Doan, Nhiem Ngoc Dao

The microstructures and kinetics of a rich iron ore ( TFe = 65.84%) of Na Rua mine, Vietnam, used for the iron production were investigated in this study. Thermal behaviors of iron ores were well-examined by heating microscopy, thermogravimetric analysis, and differential thermal analysis. After being pelletized and then oxidatively fired at 500–1200 °C for 2 h, the pellets fired at 1200 °C (P1200) displayed a hard and dense structure with a decent compressive strength of 317.9 kg/pellet whereas those fired at 500 °C (P500) had a soft and spongy structure. The reduction of iron pellets conducted in a flow of a 60–100% CO2/ Ar gas mixture at 900–1100 °C showed significantly higher efficiency than the reduction using coal. The spongy pellets showed superior performance for the reduction in the CO/Ar gas mixture compared to the dense ones, compatible with the production of sponge iron. When mixed with an amount of coal, P1200 designed for iron production in the blast furnace demonstrated an impressive reduction activity compared to P500 and previous studies. The kinetics of pellet reduction was determined by the diffusion of substances through the solid product layers having the mathematical model of 1 − 2 3 f − (1 − f )2∕3 = kt . The microstructures of pellets during the oxidative firing and reduction were also examined by X-ray diffractometry; scanning electronic microscopy; energy-dispersive X-ray spectroscopy; and Brunauer, Emmet, and Teller method.

Jun 7, 2022

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025

By A. Nieto

This article is a review of previous discussions about underground mining method selection and classification with the purpose to clearly define and classify the two groups of variables (indicators) involved in the mining selection process: key deposit indicators (KDIs) and key mining method indicators (KMIs). This paper provides a simple and clear approach for the classification and selection of a feasible underground mining method based on a predetermined set of favorable deposit characteristics, which are defined as key deposit indictors (KDIs). This article also gives a summary of the key advantages and disadvantages associated with every underground mining method based on their key mining indicators (KMIs). The selection method given in this paper is based on defining field KDIs and comparing them to the KDIs that are favorable to every considered mining method. By cross validating a matrix of favorable KDIs, the paper presents a simple approach to rank several underground mining methods using a scale from favorable to less favorable accordingly to the ore deposit characteristics (KDIs). KMIs are used to further complement KDI rankings by analyzing every method’s KMI performance based on the expected productivity of the mining operation being considered. To further assist the reader through the selection process, this paper gives basic sketches representing each of the primary underground mining methods discussed in this paper. Each method is given using the same 3D isometric view as spatial reference to assist the reader with visual interpretation and comparison between methods.

Jan 1, 2010

By W. W. Dudley

The U.S. Geological Survey, in support of underground testing of nuclear explosives, has developed a technique (Dudley, 1910) to predict the inflow of ground water to large underground chambers that are cylindrical in shape. By treating the chamber as a large-diameter well pumped at constant drawdown, the nonsteady discharge can be computed by the method of Hantush (1961) for analyzing flowing wells under leaky artesian conditions. In mining applications, whether for mineral recovery or for nuclear testing, the most serious departure from the conditions of Hantush's model results from the gradual enlargement of the opening under drained conditions. Inherent in the analytical technique is that the "well" is fully completed at the time that dewatering begins. Because safety is the prime concern, however, initial pumping systems or personnel evacuation procedures must be designed to handle the greatest conceivable inflow. DEFINITIONS Because somewhat different meanings are attached to similar words in different technical fields, the U.S. Geological Survey definitions (Lohman, 1970) of several hydrologic terms used in this report are given below. An aquifer is a formation, group of formations, or part of a formation that contains sufficient saturated permeable material to yield significant quantities of water to wells, and springs. A confining bed is a body of material lying stratigraphically adjacent to one or more aquifers and having a hydraulic conductivity distinctly lower than that of the aquifer. The total head (dimensions L) of a liquid at a given point is the sum of three components: (1) elevation head, he, which is equal to the elevation of the point above a datum; (2) pressure head, hp, which is the height of a column of static water that can be supported by the static pressure at the point; and (3) velocity head, hv, which is the height the kinetic energy of the liquid is

Jan 1, 1971

By Jerry Dolph

In September 1855, 55-year-old Noah Spencer Kellogg and his $3 jackass named Bill discovered what was known at the time as a “blow out” of high-grade lead and silver ore. The deposit was located on the side of a North Idaho mountain high above the South Fork of the Coeur d’Alene River. The ore was later assayed at 41,141 g/t (1,200 oz/st) silver. Kellogg named his discovery the Bunker Hill Lode, after the June 17, 1775 Revolutionary War battle of Bunker Hill. A thriving pioneer settlement sprang into existence around the resulting mine’s workings and was eventually— and appropriately — named Kellogg. The peak rising hundreds of feet above the mine’s adit was named “Jack-ass Peak” after Noah Kellogg’s hairy companion.

Jan 1, 1996

By B. T. Lusk, Q. Q. Huang, R. Q. Honaker, K. A. Perry

Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. It is applied either dry or wet. Both methods have advantages and disadvantages, but the formation of caked rock dust particles is cited as a significant concern for wet applications. We conducted a study to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid and sodium oleate. At a sodium oleate dosage of 1 kg/t, a contact angle of 112o was measured, indicating strong surface hydrophobicity and thus the ability to repel water. Fourier transform infrared spectroscopy (FTIR) studies indicated a chemisorption mechanism, which is necessary for long-term stability of the surface modification. The dispersibility of the modified rock dust samples was elevated by the application of both oleic acid and sodium oleate, thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed an 82.8 percent reduction in the dust explosion potential relative to untreated rock test applied by the wet technique.

Jan 1, 2015

By F. H. Seymour

Central to Newmont Gold's Mine planning system is the ability to interactively perform cut and fill operations on topographic contours and to accurately evaluate grades and tonnages within contour outlines using polygon set manipulation routines. This paper develops the applied geometry concepts that underlie these routines. Included are representation of volumes with contours, point in polygon test, block proportion in polygon calculation, polygon area and centroid calculation, and intersection, union, and complement between polygon sets.

Jan 1, 1990

Micro-computers have made it practical to install a high-speed acquisition system to collect data from a longwall face in near real-time. By simultaneous data analyses using neural networks and fuzzy sets, information regarding longwall mining performance and underground behavior can be provided and forecasting longwall instability and detecting geological anomalies is feasible. This paper presents details of the application of neural networks and fuzzy sets in developing on-line evaluation of longwall roof behavior. Techniques for interpreting longwall shield pressures and characterizing roof conditions are discussed.

Jan 1, 1996

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023

By Setareh Afrouz, Emily Sarver, Cigdem Keles

The resurgence of severe lung disease among US coal miners since the mid-1990s has led to efforts to better characterize and monitor respirable dust exposures, particularly focusing on mineral constituents from rock strata surrounding the coal. A rapid analysis method for silica (quartz) mass using direct-on-filter Fourier transform infrared (FTIR) spectroscopy has been developed, which can also estimate kaolinite, a primary silicate mineral in many coal mines.

Feb 24, 2022