Search Documents

By Kenneth N. Han

The effect of anions such as sulfate, chloride, and nitrate on the solubility of rare earth element-bearing phosphates and fluorocarbonates has been examined using relevant thermodynamic data. The study has found that these anions have significant influences on the overall dissolution of rare earth elements (REEs) from various sources in the aqueous media. The thermodynamic calculations in this study have indicated that the speciation of REEs with the anions tends to increase the overall solubility of the REE-bearing minerals. However, in some cases, strong precipitation of REEs with some of these anions causes an adverse effect on the solubility of these elements. It has been found that sulfate ion has the most pronounced effect on the solubility compared to nitrate and chloride, in which the latter two acids exhibited almost identical results. The calculated results have indicated that REE-oxide (hydrated) is the easiest compound to dissolve, followed by carbonate, phosphate, fluoride, sulfate, fluoro-carbonate, and oxalate in that order.

By Rudolph K. Hoagberg

Silica sands, primarily in coarse size ranges, are used to prop open fissures or voids created in the bedrock by hydraulic fracturing. This procedure increases the flow of gas or oil or other fluids through the bedrock. The sands used must meet various specifications relating to their physical and chemical characteristics; these characteristics are in turn related to the geologic provenance of the sand deposit. The Jordan Sandstone, a Cambrian formation which is exposed in Minnesota and Wisconsin, meets the specifications of a proppant sand by virtue of its depositional history and its sedimentary properties.

Jan 1, 1980

By NEHA PANDEY, V.K. REDDY KALLAM, SUNIL KUMAR TRIPATHY, ARIJIT BISWAS

This work discusses the sulfur dioxide (SO2) leaching of low-grade ferruginous manganese ores to selectively recover manganese (Mn) as manganese sulfate (MnSO4), followed by electrowinning of the purified MnSO4 to produce electrolytic manganese dioxide (EMD). The effects of the leaching process parameters on Mn recovery were studied, and the leaching duration and SO2 flow rate were found to have significant effects. Under the optimum conditions derived for grade 1 ore (with total Mn content of approximately 17.16 percent), the specific SO2 requirement (SSR) — that is, the SO2 flow rate per gram of Mn in the leach slurry — was calculated to be 0.014 L/min. At the SO2 flow rate calculated using SSR for grade 2 ore (with total Mn content of approximately 26.29 percent), a Mn recovery rate of 94 percent was realized. Electrowinning of the purified MnSO4 generated after leaching resulted in EMD with 88.01 percent purity and a γ structure.

Sep 1, 2022

By Qingwen Shi, Brijes Mishra

Laminated rock can delaminate and fail under certain stress states. Delamination-caused roof fall and cutter roof failure is a common failure mechanism in roadways in Pittsburgh coal seam due to the existence of laminated shale roof. Two-dimensional numerical models were developed at laboratory scale based on the bonded particle method in order to simulate the delamination with particle flow code. In these models, an assembly of bonded particles and parallel weak planes represents the laminated rock. This model calibrated the micro-parameters of the bonded particlematerial and weak planes with laboratory data. The mechanism of fracturing and delamination in a laminated specimen was investigated using unconfined and confined compression test and unsupported roof compression test. The numerical results show that, under a constant horizontal stress, delamination occurswhen the stress is much lower than its compressive strength. The confined compressive test indicates that delamination is restrained by applying confining stress since delamination-caused failure does not occur during any stage of the confined compressive test. Unsupported roof compression tests showed propagation of cutter roof failure with initiation of cracks and delamination at the intersections of the roof and ribs. An outer failed zone and inner failed zone form separately. The separated zones connect and form an opening in the roof. The presented numerical results provide additional insight into process of delamination.

Sep 14, 2020

By William H. Mount

Since the late 19405, St. Joe has operated rubber-tired, trackless mining equipment underground in its Southeast Missouri Lead Belt operations. At first, the trackless equipment was operated in conjunction with rail haulage equipment in the room-and-pillar operations, but was to later replace rail haulage completely. The first pieces of equipment to travel on pneumatic rubber tires were short-haul shuttle cars of 12-ton capacity hauling rock from the heading to the mainline railroad. Early-model drill jumbos were the next pieces of production equipment to be carried on rubber, along with mobile slusher ramps. Mobile diesel equipment, in the form of conventional rear-dump trucks, made its appearance underground in the early 1950s, introducing the era of relatively high-speed mobile equipment as compared to the electrically powered shuttle cars. Haulage distances for rubber-tired vehicles were no longer dictated by trolley lines and trailing cables and tires were subjected to increasingly severe applications. St. Joe's first completely trackless mine, the Hayden Creek Mine, was opened in 1952, employing rubber-tired drill jumbos, electric shuttle cars, and for the first time, an articulated diesel truck consisting of the tractor unit of a conventional earthmoving scraper and a rear-dump rock wagon. Those machines rolled on the first true earthmover tires to be used underground by St. Joe. The articulated truck concept proved to be very successful, and constitutes an In- creasing portion of the underground haulage today.

Jan 1, 1975

By Eric Jacobs

"Building and operating tunnels has been a highstakes endeavor in terms of costs, complexity, safety and impact on contractors, owners and the public for a long time. There are many variables that need to be closely monitored and managed to construct a tunnel on-time, on-budget and safely. Once built, there are also many elements that need to be monitored and managed to operate a tunnel safely and efficiently.Fundamentally, the risks to the safe and efficient construction and operation of a tunnel are a function of the degree of harm and the likelihood of the harm occurring. From a cyber security perspective, risk assessments used to inform decision makers and support risk responses are typically based on identification of relevant threats; internal and external vulnerabilities; the impact that may occur given the potential for threats to exploit vulnerabilities and the likelihood that harm will occur. This article focuses on creating awareness of vulnerabilities associated with technology used in tunnel construction and operation and some of the challenges associated with remediation of these vulnerabilities. As we all know, technology has been evolving at an accelerating pace and infiltrating every aspect of our lives in new and often exciting ways. In the world of tunneling, sensors and systems that provide position and time have become accurate, rugged and cost-effective enough to come out of the research labs and into the equipment and systems used every day. There are many opportunities to employ connected computing devices and sensors to costeffectively capture, integrate and analyze key data with minimal latency to manage risk better, improve safety and avoid surprises."

Jun 1, 2019

By İsmail İnce

The purpose of this study is to investigate the index-mechanical properties of igneous rocks by using the electrical resistivity method. Electrical resistivity, index (P-wave velocity, dry density, and porosity), and uniaxial compressive strength values of 48 different igneous rock samples were measured in the laboratory. Simple regression analysis was performed between index-mechanical properties and electrical resistivity values. Strong exponential and logarithmic correlations were found between electrical resistivity and the index-mechanical properties of the igneous rock samples.

Jan 21, 2022

By Paul Richardson

This paper will review several projects completed during the period from 1976 through 1984 which have been carried out utilizing big hole drilling concepts. The projects discussed will be from various industries to demonstrate the extent that big hole drilling methods are being used along with the current state of development. There will be a discussion of projects planned for the future where big hole drilling methods are the only technology being considered. Also included in the discussions will be an overview of the most recently completed heavy oil recovery project. During the next decade, big hole drilling methods will be used more and more in all industries where underground access is required. The safety, speed and economics associated with shaft sinking using drilling methods are becoming more and more recognized and the technology is rapidly becoming an accepted shaft sinking method.

Jan 1, 1985

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.

By Paul Gilmour

"The principal role of the geologist is to recognize the existence of phenomena before trying to explain them" - B.M. Keilau, 1825; A. Holmes, 1965 Some important groups of mineral deposits in the layered rocks of orogenic belts or greenstone belts occur in horizons characterized by the presence of exceptional amounts of silica, iron and carbon, with more or less significant amounts of manganese. Generally, the rocks involved are well banded. In practice, these five physical features - four compositional and one geometric - are found with many lithological guises. Iron formation, in the full, modern sense of the term (James, 1954), quartzite, ferruginous quartzite, chert, jasper, "tetsusekiei" (Horikoshi, 1969), tuffaceous jasper ("purple porphyry" - Anderson and Creasey, 1958, p. 36), ferruginous or graphitic shale, argillite, slate or schist, and hematitic tuff are but a few of the more familiar of the names that have been assigned to these rocks. Widely acknowledged and well-documented examples of metallic deposits found in such sediments include concentrations of iron and manganese and stratabound, polymetallic, massive pyritic sulfides. Less familiar examples include occurrences of asbestos (Miles, 1953; and Coetzee, et al., 1976), antimony (Coetzee, 1976), and perhaps stratabound deposits of Au-Cu-U-W-etc., such as Aitik in Sweden (Mining Magazine, 1975; and Nilsson, 1979) and Olympic Dam in South Australia (Roberts and Hudson, 1983). The case of gold is intriguing. An association between gold and iron formation has been identified at several famous deposits and districts, such as Yellowknife, N.W.T. (Morton, 1979), Homestake, S. Dak. (Sawkins and Rye, 1974), Vubachikwe, Zimbabwe (Fripp, 1976) and the Barberton district, R.S.A. (Hammerbeck, 1976). Yet a critical reading reveals the existence of many other hitherto unsuspected examples. The purpose of this note is to draw attention to that omission and the apparent explanation for it. It is not hard to detect the two most probable reasons for the discrepancy between reality and the record.Most occurrences of gold are associated, not with the familiar banded iron formation or interbedded magnetite and chert (technically, the magnetite-banded variety of the oxide facies), but with the enigmatic carbonate, sulfide and silicate facies of iron formation and/or with rocks evidently related to iron formation. All too commonly, the unfamiliar facies of iron formation have been identified by field and mine geologists and not a few researchers as products of regional metamorphism and hydrothermal alteration, as mafic igneous rocks, or as conventional sediments, ie., without regard to their intrinsically ferruginous nature. The justification for these two complementary assertions is largely to be found in the recognition of a characteristic suite of metals and minerals in gold deposits known to be associated with iron formations. Although, from a geological standpoint, a lithological association is more important than a mineralogical assemblage, the latter is the more likely of the two to be diagnostic. This arises from the different natures of mineral and rock classifications, The identification of a mineral or an element is a matter of fact. Owing to the genetic component inseparable from petrographic nomenclature, viz., "igneous": a rock (believed to have been) derived from a melt, the identification of rocks depends on inferences or conclusions about their mode of formation - conclusions that are commonly debatable and, all too often, involve subjective judgements. This is especially prone to be true, if - as at many of the gold occurrences in question - the host rocks have been metamorphosed and/or "altered". In the notes that follow greater weight has accordingly been assigned to elemental and mineralogical than to host rock composition. In other words, if, in a given gold occurrence, the suite of metals and minerals present conforms to the standards of the subject class, whereas the names assigned to host rocks do not, the latter will be viewed as suspect.

Jan 1, 1985

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By Knut H. Hubert

The GRATE-KILN System plant at Svappavaara, Sweden, was constructed for LKAB by Allis-Chalmers under a turnkey contract and commissioned in 1969. The plant was designed to produce iron ore pellets from magnetite concentrate at 6100 mtpd using imported fuel oil. It represented the state of the art for plants of its type at the time. Fuel rated capacity was attained within one week of start-up. Product quality, power usage, fuel consumption and machine wear were within warranty limits during sustained production thereafter. As operator skills improved and gas handling system reserve capability was utilized, the plant frequently produced acceptable product at up to 115% of design capacity. During the period 1969 to 1976, market demands increased for high-quality pellets while energy costs rose steadily. At the same time, important advances in the design of GRATE-KILN Systems were being made in other plants constructed by Allis-Chalmers.

Jan 1, 1980

By Steve Kral

As the mining industry watches commodity prices continue to soar, the question on most everyone’s mind is how long will this upcycle last. The con-census among speakers and attendees at the SME Annual Meeting and Exhibit is that this cycle is sustainable. The buzz at the meeting was, of course, the current boom cycle the industry is in. Most agree that China’s huge appetite for mineral commodities is part of the force driving the upturn. But the improving economies of other developing nations also plays a role. However, along with the good times come challenges. Speakers at the keynote session addressed some of the challenges and offered their opinions on the sustainability of the boom.

Jan 1, 2006

By J. van der Walt

The Meikle Mine is located in the northeastern part of Nevada in the gold-rich Carlin Trend. First discovered in 1989, Meikle is being developed into a 2.2-kt/d (2,500-stpd) underground mine that will open during the second half of 1996. Work has already been completed on the mine’s cooling plant, a necessary item due to the high rock temperature and the hot ground water. In North American mines, there has been little need for refrigerated cooling. Therefore, Barrick needed to draw on experience from elsewhere in the world — particularly South Africa — to meet these requirements. The history of cooling mines using mechanical refrigeration dates back to the 1920s at Morro Velho in Brazil and 1936 at Ooregum in India (Dobson,1940 and Biccard, 1946). From 1940 to 1960, several cooling plants were installed on the deep level gold mines on the Witwatersrand in South Africa. These were followed by similar installations on the mines in the Klerksdorp, Welkom, Evander, Rustenburg and Thabazimbi areas. The first mine cooling plant in Germany was built during 1976.

Jan 1, 1996

By John Hanna

Recently. researchers at The University of Alabama have developed a two-step method for the treatment of phosphorus sludge that includes bulk removal of phosphorus by physical separation techniques followed by remediation of the residual P4 in the sludge using a novel wet air oxidation technique known as "HSAD", Tests made on samples of the electric furnace phosphorus sludge have demonstrated that essentially complete and fast removal of the P4 in the sludge can be achieved by the HSAD wet oxidation treatment, Further studies were made to determine the applicability of the two-step process on sludges of various origins. P4 contents different pre-treatment and storage conditions, The present work discusses the mechanisms and factors controlling the HSAD wet air oxidation remediation approach.

Jan 1, 1992

By James Corcoran, Richard McLane, Joseph DeMello, Eric Carlson, Hans van de Vrugt

The Los Angeles County Transportation Authority’s Purple Line Extension Phase 1 is a $3.12 billion (USD) design-build, underground heavy rail project, connecting an existing station at Wilshire Boulevard and Western Avenue and extending west 3.92 miles under Wilshire Boulevard and terminating approximately 550 feet west of Wilshire/La Cienega Station. The project alignment runs through the heart of the world famous La Brea Tar Pits and one of the world’s largest urban oil elds. This paper presents a case history of the planning, design, and construction efforts to achieve successful construction of the bored tunnels through Reach 3 of the alignment. Further, this paper outlines the proactive partnership between the owner, Los Angeles County Metro (Metro), the Design Builder, Skanska-Traylor-Shea oint enture (STS), and Southwest Geophysics who provided the geophysical services. Specically, the project included background review of historic site data (e.g., oil eld maps, building foundation plans, historic aerial photographs, etc.), geophysical demonstration testing to ascertain the capability of borehole magnetics to detect oil wells, directional drilling of thousands of feet of horizontal and vertical boreholes, collection of high resolution magnetic gradiometer data along vertically and horizontally cased boreholes as well as the collection of surface magnetometer data, discovery (“ground truthing”) of detected geophysical anomalies, and abatement of potential obstructions within the tunnel alignment.

Jun 23, 2024

By Inoka E. Perera, Robert Hildebrandt, Gerrit V. R. Goodman, Krzysztof Cybulski, Zdzisław Dyduch, Michael J. Sapko, Marcia L. Harris

To prevent coal dust explosion propagations, rock dust needs to be lifted and suspended in the air with the coal dust during an explosion. The addition of anti-caking agents prevents caking of rock dust in the presence of water. Mining and rock dusting processes can frequently create alternating layers of rock dust and float coal dust on mine surfaces. For this test series, a thin layer of coal dust was distributed on top of a layer of either treated or non-treated rock dust in the Experimental Mine Barbara, Poland. The experimental results compare the effectiveness of treated and non-treated rock dusts to attenuate a propagating coal dust explosion initiated with either strong or weak methane explosions. Experimental results indicate that the treated rock dust performs better than non-treated rock dust in arresting a propagating explosion, especially in the presence of moisture.

Jan 20, 2020

By David L. Kuck

Siderophyle platinum-group metals and sane gold are a thousand times more abundant in metal and chondritic meteorites than in terrestrial or lunar rocks. Type I and II carbonaceous chondrites contain granules of the high boiling point metals W, Re, Mo, Ir and Os. Metal meteorites and the metal fractions of other chondrites contain siderophyle Pt, Pd, Ru, Rh, Os, Ir and Au. Spectra of sunlight reflected from asteroids, when compared with those of meteorites and specific minerals, provide a rough classification and guide to sources of precious platin-group metals.

Jan 1, 1982

By R. Washnock, P. James

"INTRODUCTION Abstract Tankhouse iron control through application of new treatment technology to mitigate conventional bleeding losses is considered. Implementation is discussed and the treatment economics explored. A representative case is assessed. Treatment benefits and application drivers for specific scenarios are noted. Background Hydrometallurgical ore processing has become a significant metal extraction/production avenue in recent decades. In copper mining; the focus for this examination, around 25% of global primary copper production and nearly 50% of US production result from various hydrothermal leaching extraction approaches coupled to Solvent Extraction/Electrowinning (SX/EW) metal production. Generally such processing is favored over pyrometallurgical processes for lower ore grades and as such is finding growing use and is expected to remain a key processing route looking forward with average world-wide ore grades falling as known ore reserves become exhausted. Target Problem And Motivation In hydrometallurgical processing the production circuit may be thought of as a chain of interlocked recirculation loops (Figure 1). Leaching dissolves the target metal from the ore along with other ore components which contaminate the Pregnant Leach Solution (PLS). Iron is a common component in copper ores and, as a result, occurs fairly ubiquitously in copper Pregnant Leach Solutions (PLS) generated by leaching. Leached components migrate through the production circuit from left to right (Figure 1) through a net combination of chemical and mechanical transport mechanisms. Selectivity at the recirculation loop interfaces tends to retard rejected component migration through the production process. As a result, overall relative contaminant migration fluxes are slower than the target metal (copper) and the contaminants tend to build up relative to copper in the more upstream portions of the processing circuit over time with iron often being a significant contaminant. Further, while copper is continuously removed from the system in appreciable amounts, little contaminant exit occurs and the absolute contaminant amounts and concentrations also increase throughout the EW circuit over time."

Jan 1, 2018

By R. D. Doepker

The dissolution of metals from various metal-mine tailings has been studied through a series of submerged tailings batch tests at U.S. Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97 pct saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79 pct or 70 pct saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained nearly constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1990