Search Documents

By Ivan C. Machado

In full autogenous grinding (FAG Mills) the ore itself determines almost exclusively the product size that will be produced, as opposed to conventional steel-media grinding where the product size can be "engineered" by changing media size, feed size, feed rate, classifier cutpoint size, etc. SAG Mills are in the middle of the way, since they offer some room to engineer their product size by properly defining some critical process variables, such as feed size, ball charge and size, mill charge and speed. SAG Mill product P80 values are typically in the range of 500 µm (35 US mesh) to 2000 µm (10 US mesh.) Whenever it is possible to determine an optimum value for the SAG Mill product P80 value (which will be the Ball Mill fresh feed F80 value), the Engineer should define the process variables that will yield a SAG product size as close as possible to the optimum calculated P80 value. In general, a coarser SAG product will draw less power from the SAG Mill and more power from the Ball Mill, and conversely, a finer SAG product will draw more power from the SAG Mill and less power from the Ball Mill. Metal consumption analyses also have to be taken into consideration, for they typically account for 30% to 45% of the total grinding cost. This presentation addresses the issue of defining an optimum SAG Mill product size (X=P80), during the design phase of the SAG and Ball milling circuits, from a general perspective, i.e., the SAG product size that will lead to an overall SAG Mill - Ball Mill optimum performance. Bond's Third Law approach is used, as well as the SPI (SAG Power Index), and also the generally accepted equations and Engineering Practice currently utilized to design SAG Mill

Jan 1, 1999

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By Joel Lööw, Jan Johansson, Lena Abrahamsson

In this study, we try to illustrate what new technology can mean for the individual miner. We formulate the notion of Mining 4.0, where we attempt to create an image of how the future might look from a miner’s perspective and how mining companies might navigate their way to a future that works for all miners. 

By David R. Delling

Introduction In 1967, Tenneco acquired Kern County Land Co. The primary reason for the acquisition was to obtain Kern's agricultural, manufacturing, and oil interests. Included in the Kern portfolio were the core of Tenneco's present sodium leases in Sweetwater County, WY. This lease base has been ex¬panded and now consists of 62 km2 (24 sq miles). Beneath this property lies more than 500 Mt (550 million st) of economic trona ore. Following the Kern acquisition, Tenneco continued exploration and feasibility studies concerning the trona leases. The effort was accelerated in 1976. Tenneco was attracted to trona because of the favorable lease position it held, the growth rate of the Wyoming industry during the 1960s and 1970s, and the prospects for a long-term, stable business enterprise. The reserve picture was certainly attractive to a company long accustomed to the never-ending struggle to replace oil and gas reserves. In 1978, Wyoming was a boom area that had experienced rapid growth for a number of years. Unemployment was very low and vacant housing nonexistent. The prospects for soda ash were somewhat different in the 1970s than now. But it was recognized even then that a new producer would have a challenging task to compete in this business. Tenneco knew the capital burden required to build a grassroots facility during inflationary time, would have to be offset elsewhere Since labor and energy are the dominant direct costs in mining trona and producing soda ash these factors have always received a great deal of attention. Contracting and permits Environmental monitoring on the site began in late 1977. With the already mentioned considerations in mind, engineering began by mid-1978. Brown & Root Inc. was selected as the general contractor for the project. S. A. Scott & Co. was the engineering subcontractor for the mine shafts, hoists, ventilation system, and miscellaneous mine facilities. Frontier-Kemper was awarded the contract for sinking the two mine shafts. Acquisition of numerous federal, state, and local permits occupied all of 1978 and 1979. The Wyoming Industrial Siting Permit, which addresses socioeconomic issues, drew the most public interest. Siting issues were all satisfactorily resolved by negotiating reasonable stipulations with various local governmental units, school districts, and the like. Site location The Green River project location is not truly remote. It is located within 5 km (3 miles) of Interstate 80 and only about 32 km (20 miles) west of the city of Green River. Nevertheless, a substantial investment had to be made in communication and utility links to the site. These included: • A 14-km (8.5-mile) rail spur connecting with the Union Pacific Railroad at Bryan, WY. This spur has four bridge structures including one crossing Interstate 80. Most soda ash is shipped by rail, and coal is received over this line as well. • A paved 5-km (3-mile) roadway connecting to Interstate 80. • A powerline extension of about 27 km (16.5 miles), along with two new substations. • A 24-km (15-mile) waterline connecting the plant to a pump station on the Green River. The site is located on gently sloping terrain at an elevation of about 2.1 km (6800 ft). Ground conditions are good for construction. Weathered bedrock lies near the surface in most places. Geology The general geology of the Green River Basin has been well described previously. Tenneco's ore is in several superimposed evaporate beds. But the bulk of it is present in Bed 17, located about 457 m

Jan 10, 1985

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) am-mines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Jan 1, 2011

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) ammines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Nov 1, 2011

By S. Shankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant. Therefore, as part of the Respirable Dust Center's ongoing research, a three part study was envisaged: study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; study of the same in the Lake Lynn Laboratory Mine of the USBM with both airflow and walking by personnel causing re-entrainment; and mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory Mine are presented. Further, the results from the wind tunnel studies are compared with the results from in-mine studies conducted at the Lake Lynn Laboratory Mine of the USBM. Comparing the results from the two studies it was observed that increasing air velocity increased the rate of re-entrainment, but increased time of exposure decreased the airborne dust concentration. Compared to same size particles, a mixture of sizes created more airborne dust concentration when re-entrained. It was also observed that contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1995

By R. Q. Honaker

Recent studies conducted at Virginia Tech have shown that ultrafine coal particles can be selectively coagulated and separated from mineral matter without the use of traditional agglomerants or flocculating agents. This technique utilizes hydrophobic interaction forces to induce coagulation of coal particles, while particles of mineral matter are dispersed using pH control. After selective coagulation, the coal coagula can be recovered by a sedimentation technique. In the present work, factors such as pH, particle size, and solids concentration have been examined. A wide range of coal samples have been successfully upgraded using this technique.

Jan 1, 1991

By M. S. Celik

Adsorption of sodium dodecylsulfonate (SDS) and dodecylaminium hydrochloride (DAH) on Buller seam coal, New Zealand, have been studied. Both surfactants adsorb effectively on the coal below pH 8, and the adsorption isotherms established at pH 4 are essentially the same at lower concentrations. These findings suggest that the adsorption of these two ionic surfactants on coal is controlled by a hydrophobic bonding mechanism. However, the results of calorimetric studies suggest that coulombic attraction also plays a part in the adsorption mechanisms. It has also been found that both the SDS and DAH adsorbed in the first monolayer are not removed by lowering the surfactant concentrations in the bulk solution.

Jan 1, 1993

By Brian F. Osborne

A continuous on-line particle size analysis system for solid/liquid suspensions is described. The basic sensor utilizes a centrifugal principle to separate particles according to size, the resultant separation being measured by means of beta-ray attenuation. Results obtained when analyzing a variety of materials at sizes from 65 mesh (210 microns) to 20 microns are discussed in de- tail. Accuracies better than 2% are demonstrated. The effects of particle specific gravity, and mixtures of materials of diverse specific gravities, are discussed from a practical and theoretical viewpoint. It is demonstrated that particle specific gravity has a minimal effect on the size reading obtained. This renders the instrument suitable for handling materials where the ratio of light to heavy component may change. The design of the first commercial installation of this instrument is described in detail. This installation will be capable of analyzing three streams in sequence, measurement at three particle sizes being effected on each stream.

Jan 1, 1973

By Peter G. Chamberlain

Domestic mining will not produce a significant portion of the manganese consumed in the United States unless new mining and processing techniques are implemented that will enable domestic lean ores to economically compete with rich foreign ores. One mining-processing technique that appears promising for certain deposits is in situ and/or heap leaching with aqueous SO2. Since leaching offers economic advantages of low capital costs, low operating costs, and short start-up times as well as environmental and safety improvements over conventional mining-processing, the Bureau of Mines studied the leachability of manganese deposits from several districts. Manganese oxides, hydroxides, and carbonates were leached to 80 to 90 pct recovery in 7 to 40 days of leaching with a solution containing 5 pct SO2 in column leaching tests. Preliminary cost analyses of surface mining-heap leaching, block caving-in situ leaching, and shrinkage stoping-in situ leaching indicate that the products of manganese leaching may be economically produced for the chemical and electrolytic manganese industries. The easiest marketable product to obtain would be a manganese sulfate commonly used as a fertilizer amendment. Manganese carbonates and hydroxides could also be precipitated from the pregnant leach solutions.

Jan 1, 1983

By Sidney M. Cohen

[Portland cement is a product made from a combination of limestone and argillaceous material which would supply the necessary amounts f calcium, silica, alumina and iron to form cementious compounds when fired at high temperatures. The resulting mixture, usually around 80% limestone and 20% argillaceous, is ground nine (80% -200 mesh), blended and then fired1 (2600-2700°F) to produce a cement clinker from which the final cement product is produced by grinding. The argillaceous component can be shale, clay, slate or other sources of the individual components of silica, alumina and iron. This paper deals with a case where a clay component was under consideration. The planned Plant site was to be located at a well defined limestone deposit. When it came to the argillaceous component, the nearest uniform deposit of clay was over 50 miles away and would require purchase of land or clay from the owner plus the daily delivery costs to the plant site. This situation made the plant site economically questionable. It was decided that a local clay deposit, which was available at the plant site but was orginally not considered due to lack of chemical uniformity and its high free silica content, would be reconsidered.]

Jan 1, 1983

By R. A. Ynchausti

In January 1993, Pyramid Resources began implementation of a supervisory expert control system at a U.S Cu concentrator. The objective of this control system was to improve plant profitability through unit operation optimization and integration. This paper documents the key aspects of the project, including: economic and associated benefits, system architecture, concepts of implementation, process control strategies, practical aspects of implementation and conclusions. The implementation of expert control at this concentrator has resulted in an estimated benefit of $50,500 per day. This is a net result of improved tonnage, reduced reagent consumption, improved concentrate grade and reduced energy per ton produced.

Jan 1, 1995

By RENE GOMEZ, RAUL CASTRO

Estimation tools and models are now available to estimate fragmentation, but some variables have yet to be studied to understand their effect on the fragmentation process. One such variable whose mechanisms have yet to be studied is the residence time, which in block caving directly depends on the distance that fragments travel from their original position in the broken ore to the drawpoint. In this study, granular material fragmentation was characterized during its flow to understand its characteristics and mechanisms. The results show that the breakage of fragment singularities occurred mainly within medium and smaller sizes, increasing fine material during flow. Thus, the main fragmentation mechanism in experiments was identified as abrasion between rock fragments where fine material continuously increases as distance increases in spite of the high rock strength and the piston flow movement used. The results presented here can be applied to incorporate fragmentation during flow of large travel distance of ore such as in block caving.

By M. S. Prasad

In earlier work it has been shown that paper filler clay products can be obtained from primary kaolin deposits of Minnesota. The objective of the current work was to reduce silica and iron contaminants and to maximize kaolin recovery to higher value products suitable for paper coating. This results in achieving a finer and cleaner product conforming to paper coating specifications. Cationic flotation and high gradient magnetic separation were used to remove free silica and iron, respectively, while attrition grinding and ultrasonics have been examined for particle size reduction. The results of this work are presented and discussed particularly with respect to application-oriented product properties. Budgetary estimates are presented for a 200,000 ton/year processing plant based on the process flowsheet developed and optimized by the study.

Jan 1, 1991

By Rameshwar Sah, PK GHORUI, LR SINGH, SIVALINGARAJU BARISETTY, SHYAM YADAV

Fly ash is a by-product generated by the combustion of coal in thermal power plants. Its disposal is a major environmental concern for these power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, a substantial quantity remains unutilized. Bentonite is commonly used as binder in the micropelletization of process waste to attain the mechanical strength required for handling and transportation. The present paper deals with the partial replacement of bentonite with fly ash in the micropelletization process without affecting the quality of the micropellets. The mechanisms of both the binders are discussed. The bonding of particles by bentonite is a physical mechanism, while fly-ash bonding is a chemical mechanism. Silica and alumina are the major constituents present in fly ash along with lime. In the presence of water, the alumino-silicates and unhydrated lime present in fly ash undergo a pozzolanic reaction and form cementitious bonds, which hold the particles together. Use of fly ash as alternative binder for bentonite has cost benefits besides providing a better utilization option for fly ash.

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

By B. Akwasi Osei

The lack of metrics to assess clamshell formation dredgeability limits the ability of engineers to predict the dredgeability of compact material and increases the risks associated with clamshell selection. Research is needed to develop metrics for predicting clamshell dredgeability. The objective of this paper is to evaluate possible metrics to predict the dredgeability of compact aggregates by hydraulically actuated clamshell dredges. Data on cylinder pressures and displacements, motor current, bucket tilt and cycle time (CT) were collected from a dredge. Work done and motor energy, potential metrics, were computed and their suitability in predicting dredgeability evaluated. Data analysis shows that; there is no correlation between tilt angle and work done or motor energy; a low correlation between CT and work done, and a strong correlation between CT and motor energy. Work done is a better measure of formation dredgeability, than motor energy, as it shows lower variability. However, in difficult digging conditions, work done alone does not accurately predict dredgeability. This work shows that, it is feasible to use cylinder pressures and motor signals data to predict dredgeability.

Jan 1, 2010

By L. G. Austin

The model originally proposed by Austin, et al., has been modified in the light of further investigation of the breakage laws in SAG milling. The model uses a fully-mixed reactor for short L/D mills and calculates the breakage of small particles by the nipping action of balls and pebbles. The autogenous self-breakage of larger lumps is treated as an effective means of fast breaking rock and much slower breaking rock. Experiments show that fast autogenous breakage can be treated as a first-order breakage with an overall specific breakage rate which incorporates fracture and chipping. Similarly, slow breakage incorporates fracture and abrasion. Autogenous breakage is cushioned by the accumulation of fine material. Simulation results are compared to results from tests in a 2 m diameter continuous pilot-scale SAG mill. Future work is discussed.

Jan 1, 1985

By F. Dehghani, M. Kebe, H. Askari-Sabzkoohi, T. Ghosh

The depletion of bauxite reserves around the world has necessitated the search for viable alternative sources of aluminum. The major non-bauxite source of aluminum is alunite [KAl3 (SO4)2(OH)6]. Lixiviation is the common industrial process to recover aluminum from alunite. Due to the presence of quartz (40%) as the main gangue mineral, this process causes the formation of Sodium aluminosilicate and Potassium aluminosilicate complexes that leads to loss of alunite, and chemical reagents. Thus, pre-concentration of alunite is required to remove the gangue minerals. Because of the low degrees of freedom (DOF) of alunite, froth flotation, as a preconcentration method, is a viable alternative to increase selectivity in downstream processes. In this work, the possibility of Alunite preconcentration with micro flotation and mechanical flotation cells was studied. The influence of type and dosage of collector, pH, solid percent, particles sizes were considered on the flotation. Flotation tests were designed based on Taguchi method, followed by performing based on surface charge differential between alunite and quartz on direct and revers flotation. In the reverse flotation, Ca+ 2 and Ba+ 2 were used to activate the quartz surface. Under optimum conditions of reverse flotation, alunite grade and recovery were 40% and 62.1% respectively. In the direct flotation, the surface of alunite was activated by F- . The grade and recovery were 50 and 89%, respectively.

Mar 2, 2022