Search Documents

By Jared Winkler, Jon A. Hummer, Aleksandar D. Bugarski, Shad Peters, Steven E. Mischler, Steve Cochrane, Shawn Vanderslice, Teresa Barone

The case study assessed submicron aerosols at a continuous miner (CM) section, diesel aerosol concentrations at the longwall (LW) section, and elemental carbon (EC) and total carbon (TC) exposures. Aerosols at CM sections were a mix of freshly generated and those from main drifts. Low ambient concentrations and personal exposures suggest effective control strategies, with further reductions possible by curbing emissions from high-emitting light-duty vehicles.

Mar 16, 2022

By P. N. Bradbury

The coal companies of today have to make all of their in-the-field managers MAINTENANCE PRODUCTION MANAGERS. By using a computer application to monitor all aspects of the daily production as well as the maintenance, a company can immediately effect a cost reduction by studying the down-time and delay trends on an everyday basis. This paper will outline how a company can use a program to not only put a stop to the increasing supply and maintenance costs but start trimming each of these cost centers while actually increasing the efficiency and productivity of the current work force.

Jan 1, 1991

By Yerkezhan Madenova, Kairat Kalmurzayev

This study intends to demonstrate the engineering application of ground penetrating radar (GPR) that would enable site engineers to prevent the high cost of blind drilling. At the tailing dump located in Zhairem Mining and Processing Plant, the challenge of sheet pile driving is encountered due to the indefinite watertight clay layer deposition depth that serves as a protective layer against groundwater contamination. A numerical model of the soil underlying the tailing dump is built using the existing hole data to compare and confirm the existing geological cross sections for three profile lines along the south and southeast parts of the tailing dump. GPR is employed to investigate the subsoil geological structure and detect the watertight clay layer deposition. On the basis of radargrams tied to the existing borehole data in the numerical model, 21 drill hole locations are suggested to assess and confirm the clay layer depth along profile lines at the tailing dump. The drilling results of the suggested holes confirmed the expected depth of the clay layer. It is concluded that GPR is a practical and economic subsurface mapping method that can prevent the high cost of blind digging of the ground and orient the drilling operations effectively.

Jan 12, 2023

By D. W. Tuckwiller

Electroplating is a widely utilized but little understood process. The fact that the average person is in contact with dozens of plated items daily without even being aware that they are electroplated is evidence of the success of the process. Although a complete explanation of electrodeposition involves thermodynamics and modern theories of bonding and catalytic reactions, in its simplest form the process conforms to the following description. A metal salt dissolved in water partially dissociates into negatively charged and positively charged ions. In the case of nickel sulfate dissolved in water, for example, a portion of the salt dissociates into positively charged nickel ions and negatively charged sulfate ions. If an electrical potential is applied between two electrodes in this solution, the nickel ions migrate toward the cathode and the sulfate ions toward the anode. The negatively charged cathode has a high concentration of electrons, which combine with the positively charged metal ions to form neutral metal atoms with a stable electron configuration. These insoluble atoms thus form a deposit on the cathode.

Jan 1, 1970

By J. L. Huiatt

The U.S. Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 5 percent K. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgSO4.2.7H20) and schoenite (K2SO4MgSO4.6H20), were conditioned in a saturated brine solution, thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular weight fatty acid. Continuous small-scale pilot plant testing indicated that 80 percent of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 11 percent K.

Jan 1, 1975

By Kunio Hashimoto

The conventional troughed belt conveyor system is the most widely used form of equipment for transporting bulk materials in the world today. The reason is not only because it is possible to transport a great deal over a long distance when compare to other types of equipment but also due to its greater economic efficiency and low initial and running costs. When dry, powdery materials and liquid materials are being conveyed, there are enclosed transport methods such as flow, case, air-slider and pipe line. In addition to features of the belt conveyor, a system employing a pipe line to transport dry powdery and liquid materials has always been considered an ideal method. This has been brought into reality through the Pipe Conveyor Sys tem.

Jan 1, 1984

By Ben L. Seegmiller

How to obtain optimum slope angles for future open pit mines using the rock mechanics approach is the subject of this paper. In the past ten years significant developments in open pit rock mechanics have come about. This has been due to the mining industry's need for the steepest, yet safe, pit slope angles attainable. Requirements for economically achieving slope stability and the actual payoff that may be achieved through stability studies have been previously discussed', by stability engineers. While the emphasis has generally been placed on the concept of "stable slopes" in the past, it is suggested that emphasis now be placed on "optimum slopes" or "optimum slope angles". A definition of an optimum slope angle is one which (1) is as steep as possible and practical from orebody and mining constraint standpoints and yet, (2) maintains the accepted standard of safety defined by a safety factor against failure and/or a probability of failure. In other words, the emphasis is placed on achieving practical stability results as defined by safety and economic considerations, as opposed to simply achieving stability. The essential purposes of this paper are to (1) outline the need for optimum slope angles, (2) discuss the procedures for using the rock mechanics approach in slope angle design for a future open pit and (3) specify the end results that may be achieved by using such an approach. While the basic concepts and recommendations outlined in this paper may be equally applicable to soil as well as rock slopes, the emphasis and procedures have been directed at rock slope angle design.

Jan 1, 1976

By Arthur E. Belton

Ever since the industrial Revolution both major and small companies have put much emphasis on the use of incentives to compensate top management for extra effort and extra skill. For many years industries have also provided hourly rate employees with incentive plans. More recently incentive plans have been extended to include the "front line" supervisors. Many companies have what are called Christmas bonus or profit-sharing plans. The incentives for foremen in mining, which we shall discuss, differ from such bonus plans in that the incentives are paid on a definite measured performance for each individual, and thus directly reflect his effort and skill. What is the objective for paying incentives? The objective for any part of an industrial Engineering Program is to increase productivity and reduce unit cost. The unit cost must include the entire cost of the program. From what base do we start an incentive plan? One should think of art incentive program as the top rung of the Industrial Engineering ladder. Therefore, a company must take several steps before reaching this top rung. The following steps are necessary:

Jan 1, 1960

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By Joseph F. Shirley

Introduction Inorganic depressants are chemicals added to the froth flotation process to maintain or produce hydrophylic surfaces on one or more minerals so they will remain in the pulp rather than attach to the air bubbles. Whether a depressant will be effective in depressing a given mineral depends on how it is used and the environment in which it is used. Some depressants must be added and conditioned into the pulp before the collector is added. Other depressants can be added in the presence of previously added collectors and effectively depress the desired minerals. Often the concentration of depressant relative to the collector concentration is critical to making an economic separation. It should be noted that some depressants will only work when specific collectors have been used. Some reagents such as sulfuric acid and hydrogen peroxide essentially act as depressants by altering the previously added collectors so that they are no longer effective. Some depressants such as sodium ferrocyanide are only effective in a very limited pH range and an essentially collector free environment. Major Depressants CaO Milk of Lime is by far the most used depressant both in tonnage and dollar value. Although it is most commonly listed as a pH modifier, it is also an important depressant for pyrite in copper and copper molybdenite flotation plants. Although a simple pH adjustment will often depress pyrite, there are times when grinding with fresh milk of lime is required to obtain optimum depression. Lime is also a molybdenite and gold depressant. NaSH Sodium hydrosulfide is by far the most commonly used reagent to depress copper and iron sulfide minerals in by-product molybdenite flotation plants. NaSH also depresses gold, silver sulfides and silver chloride. ZnSO4 Zinc sulfate is commonly used to depress sphalerite in lead-zinc and copper-lead- zinc flotation plants. It has also been used to effectively depress talc in by-product molybdenite circuits at a pH of 6.5.

Jan 1, 1986

By G. M. Clarke

Minerals are certainly where they are found. The undemocratic distribution of the world's mineral wealth has created an incongruous inbalance: mineral-rich, scarcely populated countries supply highly-populated industrialised countries that in turn consume more minerals than they produce. This has been as much a generating force for colonisation, invasion, and war as religion, political ideals, or megalomania. The Industrial Revolution of the seventeenth century was born in Britain, a country with large domestic resources of coal, iron, lead, zinc, copper, tin, etc., as well as a large population. As consumption outstripped production imports filled the gap, particularly from its worldwide colonies. For example, when Canada was founded in 1867 more than 905 of its investments were British financed, and much of these were mineral-based. The British made similar investments in South East Asia, Australasia, the Caribbean, and elsewhere, as did the other industrialised Western European countries hungry for raw materials. Later the United States emerged as a leading industrial power, again due largely to its abundant natural resources. Consumption soon exceeded production and foreign sources were saught. American business went exploring abroad ant many a mineral resource was developed almost totally on the basis of the US market many .thousands of miles away. Closer to home, Canada was also an obvious target for the US with its rich mineral resource base, small population, and geographical juxtaposition, so much so that about the time of the 1914-18 War the US took over from Britain as the major investor in Canada, and this peaked in 1967 when the US accounted for 80% of the country's foreign investment. After the 1939-45 War Japan joined the ranks of the USA and Western Europe as industrialised powers, and they too searched the world for the deposits lacking in their homeland.

Jan 1, 1981

By S. M. Carpenter

In an ever increasing ?carbon? society; management and growth will be measured by one?s carbon footprint (or output). Industries, especially mining, are under an ever increasing scrutiny of carbon, water and environmental mandates. These mandates are measured by the emissions caused by the combustion of fossil fuels. The fundamental building-block for any business, strategic or management decision must be based on an understanding of one?s ?footprint?. The scrutiny is most stringent for the commodities producers, power producers & fuel suppliers in the energy market. An overview of currently acceptable standards, application of those standards and nuances experienced in collecting the data necessary to analyze and complete a company?s carbon footprint will be presented. A lack of regulation, the fear and expectation of new and ever constraining rules, regulation and a change in the federal administration is a recipe for uncertainty in the marketplace.

Jan 1, 2010

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

Good morning ladies and gentlemen of the AIME. I was doubly pleased when Toby Yu asked me to present to you my thoughts on the past, the present, and the future of bulk transportation by barge. My first pleasure comes from sharing with you the subject that has been my career for many years. I love this industry in the same way Mark Twain loved our rivers. Somehow, I can find in all of the activities that make up this crazy barge business the same sort of excitement that he found in "steam boating." The second reason for my enthusiasm is that Toby carefully pointed out that the presentation had to be kept to a maximum of 15 minutes. I can promise you that I will hold to his maximum time limit.

Jan 1, 1982

By L. Barry Phelps

The application of an open-pit Materials Handling Simulator (OPMHS) to analyze mine planning and scheduling problems in large surface mines is discussed. The mine chosen for this application employed a large stripping dragline working in tandem with a shovel-truck haulback system for removing overburden. Large bottom-dump trucks were employed behind a coal loading shovel to transport the exposed coal out of the pit. Specifically, the current operations and the recommendations for short term and long term improvements were simulated on OPMHS. The effects of changing the operating parameters of the equipment on the total system were evaluated. Several alternatives were also studied for the best use of the existing equipment if the current operating parameters could not be improved upon. The results of the application are discussed.

Jan 1, 1978

By Mohamed Gamal, Bill Zietlow

"In oil fields that have been depleted with conventional surface oil wells but still contain significant reserves, an extraction alternative that has been constructed recently consists of a drilling gallery below the oil-bearing formation at the bottom of a 1,200-ft deep shaft where upward sloping wells are being drilled to allow oil collection by gravity. The gallery is 92-ft diameter with a flat ceiling supported by rock bolts and shotcrete structurally connected to the shaft liner, which doubles as a large tension support element. A special excavation sequence was implemented for the gallery to maximize arching in the stress above the large diameter gallery. The gallery was located in competent sandstone, constructed with sequential excavation methods, and designed with a 3D finite element model. Special consideration was given to optimizing the gallery location to take advantage of the geology for construction and support while giving good positioning to the well drilling equipment. BACKGROUND Brierley Associates was contracted to provide both design and construction management services for an approximately 1,165-ft deep, 18-ft excavated diameter vertical shaft that opens to a 92-ft diameter flat roof gallery. The geotechnical data for the site was based on information available from literature and from data obtained during core drilling and from in-situ testing in a 1250-ft deep borehole. Wire line coring was conducted using a HQ, 10-ft long core barrel with a mud-rotary drilling method through sedimentary bedrock. The geometry of the shaft and the bottom gallery is shown in Figure 1(a). GEOLOGIC SETTING AND STRUCTURAL GEOLOGY The stratigraphy at the site includes a series of interbedded marine limestone, shale, claystone, siltstone, sandstone, and chert units. Limestone and shale are the predominant lithologies in the upper approximately 675 ft, while the lower portion contains five distinct sandstone units and more abundant shale, claystone, siltstone, and coal than the upper zone. A cherty sandstone at a depth of 1,130 below ground surface (bgs) was encountered. At a depth of about 1,000 ft to 1,116 ft bgs, a non-marine sandstone unit was encountered. This sandstone is the hydrocarbon bearing layer. Joints and fractures observed in the limestone had dips ranging from 0 to 90 deg. from horizontal with joint and fracture surfaces that ranged from planar to irregular and smooth to rough. Several, near vertical shear planes with slickensides were observed with surfaces that were generally smooth and planar. RQD values for the limestone ranged from 0 to 100 percent but in general were good to excellent."

Jan 1, 2016

By P. R. Hervey

Quartz is the second most widely used electronic material, with approximately 3,000 tons of single crystals used each year. Virtually all of this material is synthetic; grown with a technique called hydrothermal growth. We will review the basics of hydrothermal growth, the feedstocks for these crystals, and the challenges to improving the growth process. We will also review the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 1999

By J. Villeneuve

Steady-state simulation has proved to be a very useful aid in designing new plants and optimizing existing ones. The algorithms and data definitions of existing simulators often, however, require a great deal of expertise for implementing a simulation-based methodology. The constraints imposed by conventional simulators are explained and the advantages of a new algorithm, the Objective-Driven Simulation, are shown. These advantages are a) an improvement in the simulation results, which enables simplifications of the methodologies used, and b) the possibility of taking into account economic objectives for plant operation, thus extending the range of application of steady-state simulation.

Jan 1, 1992

By Min Chen, Qinghua Liang, Weishan Yan, Yuan Feng, Shigang Wang

Various coal mine robots (CMRs) and unmanned aerial vehicles (UAVs) are implemented to explore unknown mines for improving the safety and efficiency of mining. It is challenging for CMRs and UAVs to achieve accurate positioning due to the absence of the Global Positioning System (GPS), poor lighting conditions, and similar geometric features in complex mine scenes. LiDAR-based localization and mapping methods are more accurate than others, while long-time running in large-scale scenarios will introduce nonnegligible cumulative errors. This study presents a semantic-aided Li- DAR simultaneous localization and mapping (SLAM) with loop closure, which leverages the uniqueness of mine intersection structure to establish stable semantic loop closure. Specifically, we propose a semantic intersection descriptor of translation and rotation invariance, which encodes 3D point clouds of the same intersection from different positions and viewpoints into a unified image. By using the semantic descriptor, we can construct a constant loop constraint when the same intersection is revisited from different directions to reduce cumulative drift. We provide experimental validation using large data sets collected in two large underground mines, namely, a simulated Edgar mine deployed in ROS Gazebo and a public underground mine data set provided by ETH. Experimental results show that the proposed method has higher localization accuracy and outperforms the existing LiDAR-based SLAM strategies.

Feb 1, 2024

By Renee Royer, Allan Punkkinen

As mines progress to ever increasing depth, new challenges are encountered with serious concerns for rock excavations in highly stressed conditions. New procedures have been undertaken or are under way to remove workers from the workface, mitigating risk and exposure to hazardous conditions. Rockbolting crews are at particular risk as they are the first line of defense in the installation of the ground support systems. One such initiative for removal of workers from danger has been with remote bolting. Equipment manufacturers have had the ability to remotely inject resin pneumatically into boreholes for several years, but it has not been recognized as a very effective method due to a variety of complications. This makes the installation of dynamic support system components such as the D-Bolt® increasingly difficult. More recently, hollow-core bolts have become popular providing far more effective installation when installed with pumpable, two component urea-silicate injection resins. Normet has developed high energy dissipation self-drilling dynamic bolts (SDDB®) to meet these challenges. Following several inquiries as to the effectiveness of pumpable resins for use with dynamic support components, Normet Canada performed comprehensive testing of the bolt and resin system at CanmetMINING in Ottawa to dispel or substantiate any preconceived beliefs. Several dynamic and static tests in direct and indirect loading were carried out. Results include tests in shear and early strength UCS of the resin to measure the performance of the SDDB compared with the established D Bolt as an effective dynamic ground support component. Underground field observations, installation methodology and in-situ testing are investigated.

Apr 26, 2022