Search Documents

By J. D. Crone

Crone Geophysics Limited in co-operation with Newmont Exploration Limited has developed a ground Pulse electromagnetic method. This is the first unit in a planned integrated system of surface and borehole Pulse EM equipment. Newmont had previously developed an operational Pulse EM unit for use in areas of very high surface conductivity. The Newmont equipment was large, heavy apparatus that required motorized transport. It operated in the equivalent frequency spectrum of 10Hz to 2.5Hz. The basic aim of Crone Geophysics was to design a Pulse EM system more portable than Newmont's. We wanted to operate in all types of field conditions including heavily wooded and mountainous terrain areas. We also wanted to record the higher frequency information that is contained in the Pulse EM waveform. There are three reasons why we thought this high frequency information was important in survey applications: (1) Field tests conducted over massive sulphide bodies in the Arizona desert showed that the desert weathering process tended to break down the electrical contact between sulphide crystals. The net effect is to reduce the conductivity of a massive sulphide body, particularly narrow bodies or highly fractured sulphide zones. In order to detect such occurances the higher frequency information is essential. (2) We wanted to be able to detect occurances with sulphide content as low as 5% sulphides that are usually poor to moderate conductors. (3) We also wanted to be able to determine the presence and extent of surficial conductive formations and clay deposits since many airborne EM anomalies are caused by such bodies. If we have the capability of detecting and recognizing these formations we would be able to explain the airborne anomaly.

Jan 1, 1976

By M. A. D. Azevedo

The effect of pulping reagents on the flotation de-inking of laser printed wastepaper was investigated with regard to the removal efficiency of toner and mineral filler particles for different pH values. These results show that caustic pulping causes the toner to be released from the fibers at larger particles sizes. On the other hand, acid pulping not only causes the toner to be released at smaller particles sizes but also increases the concurrent flotation removal of mineral filler particles. It was experimentally observed that the froth generation and stability during flotation were improved for acidic pH values.

Jan 1, 1997

By Richard Campbell, MEHMET KIZIL, Ismet Canbulat, Serkan Saydam

The design and effectiveness of ground consolidation to regain stability of longwall faces vary widely and are often based predominantly on-site precedence or what were considered successful applications at other sites in similar situations. Little is known regarding product migration characteristics or change in rockmass conditions as a result of the application of consolidation chemicals. This paper presents the in-situ testing rationale designed and implemented recently across several longwall operations in the Bowen Basin, Queensland, Australia to provide quantitative measurement of the actual zone of influence of various resin injection products. Product migra- tion was physically measured by monitoring the change in rockmass temperature as a result of the exothermic chemical reaction of the various strata consolidation chemicals used. In conjunction with strata coring and Lugeon transmissivity testing pre- and post-injection to characterise the improvement in rockmass conditions due to consolidation product injection. The results of the testing programme, migration measurements, and rockmass assessment are presented, along with a discussion on how site- based Rock Mechanics Engineers can incorporate the data into the design of strata consolidation plans.

Jun 25, 2024

By V. M. Torres

Arapiraca ore deposit has a mixed chalcopyritelbornite mineralogy, with a copper head grade of 0.7%. The reserve size does no allow profitable exploration by grinding/flotation. The technical feasibility of exploring the reserve by heap leaching was studied. Preliminary agitation tests indicated 85% copper recovery. To simulate heap leaching, column tests were performed. The tests included different ore types and acid addition levels. Operating at pH range 1.6-1.8, 67% copper extraction was achieved. Also, it was found an empirical correlation between the operation pH range, copper extraction and acid consumption.

Jan 1, 1996

By Tim M. Benson, Adam L. Lamanna, Carolina Martinez-Gutierrez, Mark J. Stephani

The Lower Concourse C Extension (LCE) 108-in Storm Sewer consists of a 2,797-foot long, 27 to 55-foot deep, 108-in I.D. storm sewer tunnel. Situated beneath active taxiways and a terminal apron at Hare International Airport (D), the tunnel diverts ows from existing storm sewers located within the footprint of a future satellite concourse. The project was delivered via Construction Manager at Risk (CMAR) as part of Chicago Department of Aviation’s (CDA) ongoing O’Hare 21 Capital Program. This paper presents project details, multiple stakeholder coordination, subsurface risks and challenges, TBM performance, and impacts to existing infrastructure.

Jun 23, 2024

By A. K. Bakshi

Mineral suspensions show Newtonian flow properties at lower solid concentration, but change into non-Newtonian regime as the solids content is increased. For Newtonian fluids viscosity is independent of shear rate, but for non-Newtonian fluids it varies with rate of shear. Therefore, measurement of viscosity at a shear rate, different from the process will be futile unless the slurry is Newtonian. This is especially true for hydrocyclone operation, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between viscosity and process efficiency. A new technique to distinguish such changes in flow type has been developed. This involved a co-axial cylinder type viscometer which measured apparent viscosity at a low shear rate, and a vibrating sphere type viscometer which measured the apparent viscosity at a high shear rate. Special precautions were taken to allow measurements of viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica of 80% passing 65~m size in water was used to prepare slurries at concentrations ranging from 1O-70wt% solids. Viscosity of each slurry sample was measured simultaneously by both the viscometers and the results were compared with each other. With this technique, it was found that all the silica slurry samples were in the Newtonian flow regime.

Jan 1, 1995

By M. Board, C. Alexander, M. Ramström, W. Johnson

"Hecla - Lucky Friday is an underground mine that has been in operation for 75 years and produces from depths over 2.3 kilometers (7,500 ft) below the surface. Technical issues at this depth include high rock temperature and seismicity. The use of new innovative mechanization is being examined for ore production. Principal advantages of mechanization are the reduced exposure of personnel, reduced seismic triggers, and increased efficiency. Lucky Friday has partnered with Atlas Copco to design, build, test, and deploy a mechanical miner for primary ore production. We will discuss the background, concept, development and deployment strategy for a mechanical miner. BACKGROUND The Coeur d’Alene mining district in northern Idaho was first discovered over 130 years ago and has been the most prolific silver producer in the US. The Lucky Friday mine of Hecla Mining Company (Figure 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 tonne per day (800 tons per day) from narrow, vertical lead-zinc-silver veins. Cut and fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates, and long travel times for worker transport to mining areas."

Jan 1, 2018

By C. Hosten

This paper presents the results from an extensive research program on the vacuum filtration of iron ore slurries. Experiments were conducted with the addition of several types of flocculants and surfactants. The filtration response of the slurries was studied in terms of the cake formation rate and the residual cake moisture. An analysis of the results is presented in ascertaining the role of flocculants and surfactants during filtration

Jan 1, 1983

By Xin Jingmin

The present trend toward concentration of mining activities into fewer sections of a coal mine and application of automation and remote control technologies favor utilization of the longwall mining method. Longwall mining also offers the potential for improving safety and productivity, better ground control and higher levels of recovery. The production potential of a longwall operation is determined by the interaction of several factors including the rate of face advance, the thickness of extraction, the speed of cutting and hauling equipment, the physical dimensions of a longwall panel, and the reliability and availability of the equipment. Some of these factors are dictated by the environment in which the extraction process is to be undertaken. Some other factors, however, can be manipulated in order to optimize the production of the system. The objective of this paper is to develop a stochastic model to simulate the production operations in longwall mining. The activities and parameters that affect the production potential of the longwall operations and the relationships between the activities are identified. An attempt is made to verify these relationships through the use of existing data. The model is then used as a computer simulator to investigate the effects of various activities and parameters on the production capacity of a panel.

Jan 1, 1983

By James J. Brady, Kenneth L. Faught, Chadi El Mohtar, Chaoshi Hu

"During construction of a 9.5-ft. diameter sanitary sewer tunnel, the City of Edmonton encountered a large pocket of flowing sand that flooded their TBM and caused significant surface subsidence, stopping further tunneling by the TBM through this zone. A unique collaborative effort ensued between the authors representing the city, consulting engineers and academic researchers to develop the optimal strategy for grouting the problematic soils. The site has a layer of very find sand between 20 and 30 ft. in depth with fines contents ranging from 5% to more than 40%. The collaboration extended from requesting additional site investigation efforts to shipping samples to the UT-Austin laboratories for grout testing plus ground and grouting characterization tests resulting in field recommendations for a full scale ground improvement program. New research information on the grouting of fine sands along with a collaborative framework for the design of in-situ grouting projects are the key topics presented. INTRODUCTION Encountering a large unexpected pocket of flowing sand with an open-faced TBM while excavating a tunnel below the groundwater table is never a good thing. This was certainly true for the City of Edmonton when one of their Lovat TBM’s became inundated by flowing sand while excavating the 9.5-ft. diameter Millwoods Double Barrel Replacement Tunnel in September 2013. However, since the City of Edmonton self-performed this work, a rare situation existed where the site could be investigated objectively, without the prejudice of contending parties selectively influencing how information was gathered and presented, to accurately examine site conditions with a goal of identifying the best remediation measures."

Jan 1, 2016

By I. González, G. Lapidus, M. Teutli

The cementation kinetics of silver with aluminum particles were studied with model solutions under nitrogen atmosphere, varying the temperature, aluminum/silver ratio, pH and concentrations of thiourea and surface activator Recoveries were evaluated both by solution concentrations and by REDOX measurements. Tafel curves were determined for this system. The results showed the cementation process to be essentially independent of the pH and thiourea concentration. However, a strong influence was observed with respect to temperature, aluminum/silver ratio and the quantity of activator. There is evidence that the controlling step is the dissolution of aluminum oxide from the particle surface.

Jan 1, 1990

By David R. Baughman, Ray V. Huff, Paul D. Chamberlin

ISL Ventures, Inc. (ISLV) is developing a process for recovering gold and silver from ores using a chloride-hypochlorite lixiviant. The leach solution, composed of water, NaCl and NaOCl, is maintained at a pH of about 7. At this pH most base metals are not leached. This is important for deposits that contain cyanide-soluble copper. An inhibitor can be incorporated to slow the decomposition of the oxidant. This paper reviews the history of development, presents details of the chemistry and indicates the nature of deposits, which we believe to be amenable to production using the process.

Jan 1, 1999

By T. Guler

Turkey has important celestite reserves in Sivas. These reserves have gypsum and/or calcite as gangue minerals. Celestite-calcite ore cannot be concentrated by gravity methods due to the low efficiency of gravity methods in fine sizes. Research was tried to concentrate celestite to a market grade by flotation. Parameters such as pH, particle size, dosage and types of collector and depressant were examined. Cyanamid A-845 and Na-oleate combination as collector, sodium silicate as depressant, and Aerofroth-65 as frother were found as the optimum flotation reagents. By applying 3-stage cleaning, a concentrate assaying 95,34 % SrS04 was obtained with 84,93 % recovery.

Jan 1, 1999

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By P. H. S. W. Kulatilake

The presence of discontinuities strongly affects the mechanical and hydraulic behavior of rock masses. Joint geometry networks play a vital role in civil, mining, and petroleum engineering projects associated with jointed rock. The need for a realistic representation of joint geometry in rock masses has been recognized. The first part of the paper shows how to build three-dimensional stochastic joint network schemes and also shows how to perform validation studies for these schemes using joint data from the Stripa mine, Sweden. Due to the existence of complex joint patterns, mechanical behavior of jointed rock masses usually exhibit scale effects and an-isotropic properties. A correct understanding of the mechanical properties (strength and deformability) of jointed rock masses is important for designing and performance estimation of structures build in and on rock masses. Beyond a certain volume, the mass proper-ties of the rock may remain essentially constant with respect to the effect of joints. This minimum volume may be used as the element size to represent the equivalent properties of a statistically homogeneous rock mass volume which contains a significant number of joints. This volume may be termed as a "Representative Elementary Volume" (REV) and may be of great importance for engineering purposes. Investigations are underway at both the 2D and 3D levels to look into the possibility of establishing relationships between REV mechanical properties and joint geometry parameters. Recently developed joint geometry modeling schemes are linked with existing distinct element codes (both 2D and 3D) to create a stochastic/deterministic stress analysis approach in achieving the goal. Results obtained so far in this direction are presented in the second part of the paper.

Jan 1, 1992

By Q. Dai

In order to float coarse sylvite particles, Potash Corporation of Saskatchewan Inc. (PCS) uses amines and extender oil (Esso 904 oil). Since the content of polycyclic aromatic (PCA) compounds in Esso 904 oil is high, PCS has sought a suitable replacement. Various types of physicochemical tests, including measurements of the electrokinetic potential of emulsified oil droplets, oil/water interfacial tension and wetting of KCl plates by oil, did not provide conclusive results. However, captive bubble contact angle measurements on KCl plates in brine in the presence of flotation agents correlated reasonably with the flotation response. A few non-toxic oils were found to provide good results in the flotation experiments and are now tested under industrial conditions.

Jan 1, 1992

By Unto Paakkinen

The testing of different kinds of process flow configurations and cell volumes in industrial scale flotation processes is in general difficult to accomplish and even expensive to perform.1 Also the lack of suitable measuring and analyzing devices often prevents effective comparison of results. Nowadays, the existing flotation processes contain, almost with exception, several return loads which result in difficult control of the process. There exist two good reasons for testing different kinds of flotation circuits at the Outokumpu Oy Kotalahti mine. Firstly it is easy to change the process flow configuration without any additional installation work and secondly, the concentrator is highly automated with magnetic flow meters, on-line analyzer and process computers. In this presentation, open circuit flotation is compared with the classical closed circuit flotation which contains return loads. In additional, the effectiveness of computer control in both cases is estimated and also the effect of cell volume on flotation results is examined.

Jan 1, 1977

By Raymond E. Zimmerman

The use of standard dense-media cyclones is well known, as they have been in use for many years. They are especially well suited for operating at low separating densities and for treating difficult coals containing a high percentage of near-gravity at the point of separation. Very few modifications of the basic design have ever been made. The author recently, however, has been interested in the development of a new type of dense-media cyclone that has been produced in Japan. He has observed the testing of this unit and has collected much data which he feels should be of considerable interest to coal preparation engineers. He feels that this unit, called the Swirl Cyclone, may be of substantial value as an alternate to the standard cyclones. It is certainly worthy of further investigation. There has been relatively little written in English-language publications on the Swirl Cyclone. It was briefly described at the Fifth International Coal Preparation Congress. I It has been described in a general manner by the author in two prior publications. 2, 3 This paper proposes to describe this device in more detail and at the same time submit technical data illustrating its wide characteristics.

Jan 1, 1977

By William I. Weisman

Natural sodium sulfate is obtained from both brines and solid deposits. The brines almost always contain other salts with sodium chloride predominating. They may be obtained from surface occurrences, such as Great Salt Lake or from shallow subterranean deposits. Althought many sodium sulfate minerals are known to exist, only three are of commercial significance. These are thenardite, the anhydrous salt; mirabilite, the decahydrate; and glauberite, the double salt of sodium and calcium sulfate. The reader is referred to Weisman (1983) for details on mineralogy and geology of sodium sulfate minerals. Sodium sulfate deposits, either in the form of brine or solid minerals, are found in many parts of the world. Natural sources, by far, provide the primary supply of commercial grades in Canada, Mexico, Spain, and probably in the U.S.S.R., Chile, Argentina, and Turkey. In the United States, production of natural material and synthetic (including by-product) are about equal in volume and have been for many years.

Jan 1, 1984

By Frank Pollard

The Australian coal industry over recent years has experienced the situation whereby exploration and mine development are moving into geographical areas where the coal seams have never been mined to any extent in the past, if at all, and particularly where there is no history of experience in preparation of these seams. Additionally, the demands have been such that the development of a mine up to production stage should proceed with minimum delay. This is a situation which is of some importance and concern, in view of the coal quality requirements now experienced within world markets which can only be met, in most cases, by careful preparation. Costs are such that the preparation plant should operate as required by the situation and with maximum efficiency, which means that laboratoty information of breakage and washability characteristics which are required for preparation plant design should be accurate and available as soon as possible, even to a certain extent during the progress of the exploration.

Jan 1, 1981