Search Documents

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

"From 2011–2016 there were 1,511 documented injures, including 7 fatalities, from ground falls in U.S. underground coal mines. The majority of these ground fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely utilized in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Mine Roof Simulator (MRS) in Pittsburgh, PA. The load-displacement characteristics of a 2.4-m x 3.7-m panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of displacement loading rate, load pull surface geometry, and the inclusion of roof channel on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines. INTRODUCTION Over 1,500 injures, including 7 fatalities, occurred from 2011–2016 from ground falls in U.S. underground mines with the majority of these ground-fall injuries caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Comptonet al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Pittsburgh Research Laboratory (PRL)."

Jan 1, 2018

By Takashi Goto

In 1968 three historical rockbursts had occurred at Bibai Coal Mine in Hokkaido. At the time they had been observed by several seismic observatories as natural earthquakes away more than 100km from Bibai City. These facts taught us that the occuerrence of failure yielded in underground opening that was accompanied with seismic wave could be observed by seismometer on the surface. After two years from this desaster, the study concerning to microseismic events generated from underground mining panels has been begun by researchers with heart-throb.

Jan 1, 1982

By W. D. Elston, A. E. McLaughlin, G. B. Hampton, W. L. Barham, J. F. Murphy, W. H. Cundiff, J. W. Mulloy, R. G. Breuer, J. W. Shaffer

Introduction Alumina (aluminum oxide) is the material from which all the world's aluminum is produced. In the Western World, all the alumina is made from bauxite by the Bayer process. In the nearly 150 years since aluminum was first isolated by Oersted, the metal has grown from a laboratory curiosity to a position of major importance in the world's commerce. In terms of annual production rates aluminum is first among nonferrous metals. Oersted's discovery-reduction of aluminum chloride with potas¬sium amalgam-was improved on by Ste. Claire Deville, whose so¬dium amalgam reduction of aluminum chloride led to the commercial production of aluminum in France in 1855. Ste. Claire Deville's method prevailed until 1886 when Charles Martin Hall and Paul T. Heroult each invented a process for the production of aluminum by the electrolysis of alumina dissolved in molten cryolite. The inven¬tion by Karl Josef Bayer in 1888 of an economical process for making very pure aluminum oxide (alumina) from bauxite established the necessary link between known ores and the Hall-Heroult reduction process. Bayer's work completed the scientific base-the ore bauxite refined to alumina by the Bayer process (U.S. Patent No. 515,895), the alumina reduced to aluminum in the Hall-Heroult cell (U.S. Patent No. 400,766--upon which today's aluminum industry is founded. Small-scale production of aluminum in the U.S. began in 1888 utilizing the Hall cell. By 1903, bauxite properties and a Bayer process refining step had been incorporated into the production activities. On this base the aluminum industry in the U.S. has grown at an annual compounded rate of 15%. Since 1946 the annual growth rate has been 10%.1 The rapid growth of the industry is the result of many factors among which are the existence of widespread bauxite ore deposits; a sound and economic production technology; and the properties of the metal-lightness, strength, ductility, good electrical and heat con¬ductivity, and pleasing appearance, which lead to ever greater de¬mands for aluminum in an industrializing society. At the inception of the industry, the only market that could be found for aluminum was in the production of cooking utensils. How¬ ever, the rapidly accelerating industrial and technological development of the Western World soon created new needs for aluminum, and today aluminum is marketed in a broad range of industrial, commer¬cial, and consumer applications. The principal uses for aluminum are:' building and construction, 22%; transportation, 18%; electrical, 13%; packaging, 11%; consumer durables, 10%; machinery and equipment, 7%; other, 19%. The 1974 production of primary alumi¬num in the world was 14.5 million short tons, which at an approximate ingot price of 40¢ per lb puts a value of $11.6 billion on the industry product prior to fabrication. While aluminum is widely distributed in the earth's crust and is a major constituent of many rocks and soils, to date no method of extraction of aluminum from such nonbauxite material has been brought to commercial practice in the Western World. In the USSR alumina is produced by the complex processing of nepheline syenite, but elsewhere all commercial production of alumina is from bauxite. A brief discussion of recent developments and other processes for alumina is included in the subsection "Other Processes for Alumina," page 19-15. In early 1973, a major U.S. aluminum producer announced the successful development of processes for the production of aluminum from aluminum chloride. This achievement promises to exert a major influence on the future of the aluminum industry. In the initial com¬mercial application of this new technology, Bayer alumina will be chlorinated, and the aluminum chloride then reduced by electrolysis. Important claims for the new processes are lower energy requirements (one-third less than obtainable in Hall cells) and reduced labor costs. Capital costs are said to be no greater than for conventional plants. While the announced intention is to produce the aluminum chlo¬ride from Bayer process alumina, the new chloride reduction process will eliminate the other raw materials, carbon and fluorides, required by the conventional Hall cells. The electrodes in the chloride cell will not be consumed on the reduction process and the electrolyte will have, as the name indicates, a chloride rather than a fluoride base. 2. Bauxite Definition and Origin. Bauxite is a naturally occurring raw material composed principally of a mixture of one or more of the hy¬drated aluminum oxide minerals gibbsite (Al2O2 3H2O), boehmite (Al2O3 H2O), and diaspore (Al2O, - H2O), and impurities of silica, iron oxide, titania, and other various elements in trace amounts. It is an end or near-end product of chemical weathering. Depending on the amount of iron impurities, the color of bauxite varies from dark red and brown to pink to white. Some bauxite is finely divided, free digging earthy material, while other forms are dense and rocky, requiring explosives in mining. Many gradational forms exist. It is one of the most variable of mineral raw materials in chemical composition and physical appearance. It is generally believed that bauxite deposits resulted from intense chemical weathering of aluminum-bearing rocks or formations under tropical or subtropical conditions with alternating wet and dry sea¬sons. Topographic conditions were favorable for drainage and the in-situ accumulation of aluminum, iron, and titanium oxides. There was low to moderate topographic relief with a minimum of erosion during long quiet periods in earth history.2 The occurrence of bauxite is widespread and it has been found on all continents except Antarctica. Production was reported from 27 countries in 1974, at which time total world production was over 79 million metric tons. Of this production 76% was from seven coun¬tries-Australia, Jamaica, Surinam, Guinea, USSR, Guyana, and Greece-which ranked in that order of production. In Table 1 are shown typical compositions of bauxite from some

Jan 1, 1985

By George Hope, Edward H. Smith

In late 1989, LAC Minerals purchased 65% of Bond International Gold and as a result became controlling shareholder of the El Indio Mine through Bond and San Jose. El Indio is a world class, complex sulphide gold deposit located in the hydrothermal alteration belt of the Andes mountains in the 4th Region of Chile. The mine is located in the high Andes about 185 km east of La Serena at an elevation of 4000 meters. The 1450 workers at El Indio live in the mine camp at 3200 m and on days off are bussed to La Serena. The El Indio mine was started in 1979 by St. Joe Minerals Corp., bought by Bond in 1987 and subsequently by LAC in 1989. The mine has produced 2.7 million oz. of gold, 9. 5 million oz. of silver and 170,000 t of copper since start of operation. The mill is currently operating at a rate of 2850 t/d and producing a copper/gold concentrate which is roasted to produce a copper/gold calcine and high quality, saleable crude As203• A small proportion of the precious metals are also produced as bullion from the leach circuit. Total production during 1989 was 224,197 ounces of gold, 1,309,342 ounces of silver and 26,968 tonnes of copper. The average cash cost of production for the period was U.S. $96 per ounce of gold, net of by-product credits. The average realized price was $5.30 per ounce of silver and $1.14 per pound of copper.

Jan 1, 1990

By R. McCulloch

Exploration activity in metallic minerals continued to decline in Montana in 1992 as companies either reduced budgets or left the state. The number of active projects dropped another 50% from 1991. Expenditures were 3% to 6% of 1989's 28.6 million. Many of the major mining companies closed offices in Montana. Although depressed commodity prices have hurried the exodus, continuous changes in environmental regulations, as well as the Mining Law of 1872, without regard to economic effect have had the most serious impact. Many companies indicate that Third World countries present a more stable business environment than the United States. Grassroots projects are nearly non-existent, while late-stage programs continue cautiously. Exploration activity continued at the following projects: Garnet, Pegasus Gold; Southern Cross, Asarco; Elkhorn, Goldfields; 7-Up-Pete, Phelps Dodge and Canyon Resources; Miller Mountain, Pegasus Gold; Sheep Creek, Cominco American Resources; Checkerboard, Kennecott and BHP Utah International; Emigrant Creek, Pegasus Gold; and Crevise, American Copper and Nickel. All mineral activity, whether on private, state or federal land, is regulated by the Montana Department of State Lands under three classes of permits - Small Miner Exclusion Statements (SMES), Exploration Licenses and Operating Permits. A total of 230 Exploration Licenses are active in the state with 26 of those being new. However, there are only 433 projects current in Montana, with many of those in the reclaiming stage. The majority of exploration projects consist of individuals expending time rather than money on properties. The number of mines functioning under operating plans declined by one when W.R. Grace closed its Zonolite operation.

Jan 1, 1993

By M. Yekich, W. R. Reed, G. Ross, A. Salem

"Canopy air curtain (CAC) technology has been developed by the National Institute for Occupational Safety and Health (NIOSH) for use on continuous miners and subsequently roof bolting machines in underground coal mines to protect operators of these machines from overexposure to respirator coal mine dust. The next logical progression is to develop a CAC for shuttle cars to protect operators from the same overexposures. NIOSH awarded a contract to Marshall University and J.H. Fletcher to develop the shuttle car CAC. NIOSH conducted laboratory testing to determine the dust control efficiency of the shuttle car CAC. Testing was conducted on two different cab configurations: a center drive similar to that on a Joy 10SC32AA cab model and an end drive similar to that on a Joy 10SC32AB cab model. Three different ventilation velocities were tested—0.61, 2.0, 4.3 m/s (120, 400, and 850 fpm). The lowest, 0.61 m/s (120 fpm), represented the ventilation velocity encountered during loading by the continuous miner, while the 4.3 m/s (850 fpm) velocity represented ventilation velocity airflow over the shuttle car while tramming against ventilation airflow. Test results showed an average of the dust control efficiencies ranging from 74–83% for 0.61 m/s (120 fpm), 39–43% for 2.0 m/s (400 fpm), and 6–16% for 4.3 m/s (850 fpm). Minor modifications to the shuttle car CAC design and placement improved the dust control efficiency to 51–55% for 4.3 m/s (850 fpm) with minimal impact on dust control efficiencies for lower ventilation velocities. These laboratory tests demonstrate that the newly developed shuttle car CAC has the potential to successfully protect shuttle car operators from coal mine respirable dust overexposures. INTRODUCTION The development of the canopy air curtain (CAC) dates back to the 1970s starting with the initial development of the CAC by the Donaldson Company, Inc. under contract from the U.S. Bureau of Mines [Krisko 1975]. This CAC was originally developed for continuous miner operators when continuous mining machines had cabs. The need for a CAC on the continuous miner was eliminated when the cab was removed from the machine design. However, CAC development progressed to include CAC designs for a roof bolting machine to protect roof bolters from respirable coal mine dust [Goodman and Organiscak 2002, Listak and Beck 2012, Reed et al. 2017]. This roof bolting machine CAC research continues to the present day."

Jan 1, 2018

By W. R. Peters

An experimental hole-to-hole seismic probe system has been developed for use in coal measure geology as a means of determining the structural conditions of coal seams. The source probe produces a 500-joule electric arc discharge whose seismic wavelet has a spectrum in the 200 to 2,000 Hz frequency range. Low compliance hydrophones contained in the source probe as well as in a separate seismic detector probe are matched to the frequency range of the source. Both probes are constructed with 5-72 cm diameter housings. The transducers in the probes are equipped with fluid-inflatable boots to permit operation in either wet or dry boreholes. Preliminary tests in vertical boreholes drilled 213 m apart in sedimentary rock formations show reliable operation and useful seismic propagation measurements along horizontal and oblique paths up to 232 m in length. Because the seismic wave- let has an accurately repeatable waveshape, multiple shots and signal averaging techniques can be used to enhance the signal-to-noise ratio and extend the transmission distances.

Jan 1, 1985

By G. A. Kordosky

LIX® 34 liquid ion exchange reagent, one of a totally new class of metal extractants, is discussed in terms of its properties. Specifically, these properties include improved selectivity for copper and greater recovery. Some comparisons to the well known General Mills' LIX® 64N have been made. Particular emphasis is given to treating solutions containing very low copper values and high impurity levels.

Jan 1, 1976

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By Keith J. Henley, Nicholas C. Clarke, Paul Sauter

A detailed investigation of the stability in cyanide solutions of native gold and gold-silver tellurides in a flotation concentrate from the Golden Mile, Kalgoorlie, has been undertaken to assess whether leaching under different conditions can be used to quantify the distribution of Au between native gold and gold-silver tellurides, as suggested by, for example, Chryssoulis and Cabri (1990). The leaching was carried out on +20 µm native gold and gold-silver tellurides separated from a high-grade flotation concentrate and then diluted with barren quartz. The material leached assayed 270 ppm Au and 118 ppm Te and the leach conditions used were:- Stage 1: Leaching in dilute cyanide (0 .1 % ) at pH 9 .5 for 24 hours to dissolve native gold but not gold-silver tel­lurides. Stage 2: Leaching the residue from Stage 1 in strong cyanide (2%) and pH 12.5 for 96 hours to dissolve gold-silver tellurides.

Jan 1, 1995

By Michael Karmis

"In December 2011, the U.S. Attorney’s Office for the Southern District of West Virginia, the U.S. Department of Justice, Alpha Natural Resources (ANR) and Alpha Appalachia Holdings entered into a nonprosecution agreement related to the explosion at the Upper Big Branch Mine (UBB) that killed 29 miners. This coal operation was owned by Performance Coal Co., an affiliate of Massey Energy Co., which was acquired by ANR in June 2011, more than a year after the UBB explosion. Pursuant to the agreement, ANR agreed to:• Establish a trust within 120 days.• Pay a total of US$48 million into the trust to be used solely to fund and administer research and development (R&D) projects to improve mine health and safety.• Administer the trust by three highly qualified individuals with academic and/or professional backgrounds in mine health and safety.In April 2012, the Alpha Foundation for the Improvement of Mine Safety and Health was created. The three directors - Michael Karmis, president; David Wegman, vice presidenttreasurer, and Keith Heasley, vice presidentsecretary - approved a plan to expend both the interest and principal of the trust, aiming at an 8-10 year research horizon. The foundation also appointed David Belden, an experienced manager of nonprofits and professional associations, as the first executive director of the foundation. The IRS approved the foundation’s tax-exempt application, as described in Section 501c(3) of the Internal Revenue Code, on Dec. 18, 2012. The board established guiding principles of the foundation, which are as follows:• Mission: to improve mine health and safety through funding R&D projects to qualified academic institutions and other not-for-profit organizations.• Vision: to enable miners in the future to be free of work related injury or disease by the implementation of the results of the projects funded by the foundation and undertaken by the best researchers from any discipline that can contribute. The foundation is now approaching its third year and regularly posts updates, including semi-annual reports, to its website (www.http.alpha-foundation.org/), which serves as the main medium for communication with the broader stakeholder community"

Jan 1, 2014

By Daniel R. Walton

This paper covers several points of interest to mine engineers and planners involved in evaluating or conducting geostatistical coal reserve estimates. In particular, the ability to optimize borehole drilling locations and minimize drilling costs is addressed. Also discussed is the concept of confidence intervals for estimated coal characteristics obtained through geostatistical estimates and their importance in decision-making for mine planners. Finally, a discussion is presented on how geostatistics enables identification of invalid data points and actually forces strict attention to data editing and proper geologic interpretation.

Jan 1, 1982

By C. G. Hunkin

In situ, or in-place leaching is concerned with the extraction of metals from natural mineral disseminations without removal from their geologic location which, in many cases, amounts to the reversal of the deposition process accompanied by a presumed increase in velocity of the processes, if the project is to be profitable. Solution mining processes involve removal of minerals such as sulfur, common salt, and potash, generally leaving cavernous voids, in contrast to in situ leaching which term is applied to the selective dissolution of a mineral from its gangue without sensible disturbance of the formation. Where such a process can be operated, the advantages are manifold and have been so recognized by miners from the earliest days of mining. Recent technological developments have encouraged a reassessment of the status of in situ leaching, and it now appears possible to extend the application of the method from a few isolated special situations to many uranium and copper deposits. Anaconda's interest in the techniques stems from long experience with vat and heap leaching, 'dump leaching, and natural leach activities associated with several established mines. Increasing activity through-out the industry has been noted, particularly in leaching low grade pillars and the peripheral zones of operating mines, often by the introduction of leach solutions via boreholes drilled from surface. Reactivation of dormant mines] using similar techniques has been successful. Over the long term, environmental improvement activity will lead to excess sulfuric acid production, even to a disposal problem. The cost of leach solutions and reagents must be reexamined in this light. The mineral industry now classifies as uneconomic deposits of readily soluole minerals whose potential value, on a per acre basis, may De several times that of many currently profitable oil field reser-

Jan 1, 1971

By Hossein Kazemi

This article is a review of fluid flow and mass transport in fractured rocks. The topics include: single-phase and multiple- phase flow theory, formation productivity or injectivity improvement by artificial fracturing, and mass transport associated with fracture acidizing. Possible extension and application of such ideas to in situ mining in fractured rocks are presented.

Jan 1, 1974

By Edward J. Budill

One of the most dramatic innovations in the materials handling industry has been the development of stacker cranes and automated material handling systems. The stacker crane with its many capabilities and the development of reliable industrial automation controls have combined to produce dramatic achievements in an area once characterized by inefficiency lack of management attention, and capital investment. In many areas of application however, stacker cranes and high rise storage systems have been designed and installed with insufficient thought given to their integration into the overall operations of the plant or distribution facility. This paper will look at some new and interesting breakthroughs in the integration of stacker cranes and high rise storage systems into the total manufacturing plant system. In this paper we will refer to both bridge type stacker cranes and aisle stackers. The bridge type stacker crane was developed first and was initially developed with forks or other handling devices hoisted up and down a rigid or telescopic mast. This mast system was suspended from a trolley mounted on an overhead crane bridge. Today, the primary application of the bridge type stacker is in warehousing systems for handling basic metal products such as coils, bars, sheets and plates. There is no question that the bridge type stacker has achieved notable results in storage and handling of these commodities. However, a new area for stacker crane application has been developing which in many cases over-shadows the accomplishments in the storage area. This is the application of the bridge stacker as an integral part of the manufacturing processes, or in other terms the production applications of stacker cranes. The stacker crane has a number of attributes which makes these applications very important. First, the crane bridge provides the stable platform for the mounting of machinery which can accommodate the hoisting and lateral movement of large capacity loads. Today stacker cranes are being built with capacities of up to 30 - 40 tons. The bridge cranes can easily accomplish accommodation Of these large tonnages. Secondly, the mast system provides a stable platform for the mounting of a wide variety of manipulating devices which can be used for the placement of material into manufacturing processes, the extraction of this material from these processes, and movement to other points in the process area. These attributes combined with excellent operator control and safety have led to development of the stacker crane as a production tool.

Jan 1, 1973

By Richard L. Ranich, Frank F. Aplan, J. B. Hiskey, Robert S. Thompson, B. J. Scheiner

Acidic waters typified by acid mine drainage, copper dump leach solutions and steel pickle liquors will typically contain SO4-2 and cations such as Fe+3, AI+3 and for the pickle liquors, sometimes Cr+3. These acidic waters will often react with limestone, present naturally or introduced for purposes of solution neutralization, to form reaction - inhibiting coatings of gypsum and gelatinous, metal hydroxide precipi¬tates. The coating thickness, as a function of pH, was quantified for both reactive (calcite, limestone) and non-reactive (quartz, barite, fluorite) minerals, and the data were related to the hydroxy species diagrams and to solution turbidity measurements. Coatings were found on the reactive minerals at a lower bulk solution pH than on the non-reactive minerals.

Jan 1, 1993

By M. A. Georgiana

The Emerald Mine No. 1, located in southwestern Pennsylvania is presently owned and operated by Cyprus Minerals of Englewood, Colorado. High volatile bituminous coal is produced from the Pittsburgh No. 8 seam by both longwall and continuous mining methods. The coal is then mechanically cleaned on site utilizing a combination of heavy media separation and froth flotation methods prior to shipment to both the metallurgical and steam coal markets. The Emerald Mine is presently producing 2.8 million raw tons per year, while liberating approximately 6.5 million ft per day of methane. In light of the methane liberation rate, ventilation requirements have been significant and have always received utmost priority and consideration. Figure 1 shows the locations of the current and proposed shafts. Emerald utilizes two Joy (Model M120-58-880) axial vane fans on shafts No. 1, No. 2R, No. 3R. (one operational, one stand-by) The use of computer simulation of various ventilation networks was initially employed during the design stages (1975-1977) and has been utilized through the present. Obviously, the initial planning, under the ownership of Lykes Resources, was strictly theoretical. All the quantities were proposed and the resistances were based on prior simulations of other mines and mathematical formulas. However, once the mine was moderately developed, actual values were recorded and utilized. This procedure consists of: a) layout pressure and quantity points b) measure all air quantities where an air course splits

Jan 1, 1986

By Earl Gardiner, Michael Grenier, Stephen Hardcastle, John Vergunst

A prototype, self-contained mine refuge station air supply sys- tem was tested in an underground metal mine to verify it's ability to keep oxygen and catbon dioxide levels at acceptable concentrations in an emergency situation. In this test, 25 volunteers were assembled and sealed in a functional underground refuge station for a period of 24 hours, without the benefit of the standard com- pressed air supply. The prototype system was designed to: 1) operate on a self-contained power supply for a period of at least 27 hours; 2) supply oxygen at a metered rate; and 3) remove car- bon dioxide by re-circulating refuge station air through soda lime scrubbing beds. During the test period, the catbon dioxide concentration remained at an average of 2500ppm and oxygen concentration stayed between 20.2% and 20.6%. The volunteers found the prototype easy to use and seemed confident in its ability to provide a safe atmosphere. The test showed that this technology could become part of an underground mine's refuge station emergency equipment.

Jan 1, 1997

By Frank C. Appleyard

As the environmental movement gained force during the past few years, it was inevitable that attention would be focused on surface mining, and we have seen this method of extracting minerals from the ground come under heavy attack by conservation groups, the press and television, legislators at all levels of government,, and the public at large. It is difficult, and in some situations, perhaps impossible, to measure either the need for, or the results of, land reclamation in absolute terms. Therefore, much of the criticism of surface mining has been based upon subjective analysis rather than hard data, with the result that discussion of the subject often includes a fair amount of emotional response. To be fair, this reaction is not limited to just our critics; even we hard headed engineers sometimes respond in the same way, an observation with which you may agree when I finish this talk. This leads to the thought that whether you are for it, or against it, land reclamation in many respects is a state of mind. That is, our reaction to it can vary considerably, depending on how far we have thought it through. And think it through we must, because the pressures being brought to bear need to be met with positive actions if the problem is to be brought under control, and in the next few minutes I would like to discuss from a management point of view some ideas which might aid in this thinking process. It would be a mistake, I believe, to think that the current energy crisis will suddenly bring the environmental movement to a stop, and therefore, we can relax and go back to running our busi¬ness the way we used to. This is not realistic; on the contrary the energy crisis is focusing attention on the limitations of our natural resources as nothing else could, and with respect to land

Jan 1, 1974

By Dermot M. Ross-Brown

The objectives of this generic study were to use numerical modeling techniques to determine under what conditions seismic waves generated by an earthquake might cause instability to an underground opening, or cause fracturing and joint movement that would lead to an increase in the permeability of the rock mass. In general, the study showed that moderate earthquakes (up to 0.41 g) did not cause instability of the tunnel or major fracturing of the rock mass. An artificial rock-burst tremor with high accelerations, however, was found to be amplified around the tunnel, and fracturing occurred as a result of the seismic loading in salt and granite. In shale, even moderate seismic loading resulted in tunnel collapse.

Jan 1, 1981