Search Documents

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By B. Das

Most coals are susceptible to spontaneous heating which in turn creates problem to mining, storage and transportation of coal. It is impossible in actual practice o eliminate spontaneous heating but spontaneous combustion can effecively be controlled through a clear understanding of its mechanism and the factors affecting it. There are altogether six stages in the process of spontaneous combustion. This includes the water adsorption stage and six oxidation stages: chemi-sorption (upto 70°C), decomposition of peroxygens (70°C-150°C), oxy-coal formation (150°C-230°C), combustion initiation (230°C) and active combustion (> 230°C). Heat is produced in all these stages. On the other hand heat is also dissipated so that some equilibrium temperature is reached. If this temperature exceeds a certain critical value (generally about 70°C), coal oxidation may advance to spontaneous combustion. The major factors influencing spontaneous combustion of coal are: coal rank, maceral composition,, water, mineral matter, joints and fissures, seam depth and thickness, mine Layout, method of ventilation, etc. Susceptibility is high for low rank coals and generally decreases with increase in rank. Of the macerals, the exinites are generally most susceptible, the inertinites least and the vitrinites somewhere in between. Water plays a major role on the spontaneous heating of coal, assisting in someways and inhibiting in other. Unrecovered coal in the gob (generally in thick seams) is a major source of fire hazards and this is specially important in shallow mine. Proper design of mine ventilation system can substantially reduce the risk of mine fire. Panel layout and load transfer can affect the development of induced cracks which in turn influence spontaneous heating. Finally, the difference between the spontaneous heating of coal in a seam and that in storage or transportation is mainly due to the change in moistured content, air circulation through the coal and coal fragmentation. These aspects have been analyzed in this paper with a view o reducing the risk of spontaneous combustion.

Jan 1, 1986

By W. Lorenz

The responsible treatment of natural resources, including mineral raw materials, contributes to the protection of the environment. The management of resources and the environment encompasses reduction of emission through application of environmentally friendly processes, economical use of resources, recycling and substitution, application of energy saving processes, land reclamation and recultivation, as well as a well balanced regional and land use planning. A variety of materials are needed for measures to protect the environment. Many of these materials are, or to a large percentage consist of, mineral raw materials, which become effective either directly or indirectly in their natural state or after an appropriate industrial treatment. We call them environmental minerals. Although extraction and processing of these mineral raw materials destined for use in the protection of the environment, may have a negative impact on the environment on one hand, preventive or curing measures to protect the environment on the other would not be possible without them. We have to accept certain smaller burdens of the environment, which naturally will have to be kept at the lowest possible level, in order to avoid or minimize greater damages to nature. In the broad group of industrial minerals and rocks there is a wide variety of mineral raw materials, which lend themselves for countermeasures in favor of the environment. To hamper their production and processing through excessive environmental regulations would make the protection of the very environment more difficult or even impossible.

Jan 1, 1995

By A. A. Campoli

A stress control design strategy was developed to minimize the explosive failure of highly stressed pillars, during room-and-pillar retreat mining conducted between stiff immediate roof-and-floor strata. A confined core coal pillar strength model was based on in-mine geotechnical evaluations of successful room-and-pillar and longwall bump control designs. Tributary area and linear shear angle approaches were used to estimate development and gob side abutment pillar loads for supercritical section widths. Subcritical width sections separated by barrier pillars to control stress within total extraction panels were optimized with the boundary element program MULSIM/NL.

Jan 1, 1994

By Carlos Álvarez, Sergio Sánchez, Michael Mains, Giuseppe Gaspari

Extensive record of tunnels excavated with SEM (sequential excavation method) in swelling grounds exists in literature: global experiences include successful tunnelling both through clayey and rock masses with time dependant deformation. However, TBM (tunnel boring machine) use in swelling conditions with high water pressures (EPB, earth pressure balance, machines or slurry shields) is much less documented, considering the lower expected impact due to the limited stress relief and operations under saturated conditions. This paper summarizes a number of studies conducted as part of the risk assessment and detailed design of a large diameter TBM tunnel in variable and challenging geological conditions. The tunnel alignment is driven through mixed face conditions including swelling soils and clayey soft rocks, prone to intense time-dependent deformations. The paper also describes the approach adopted for the design of pre-cast segmental lining subject to both swelling actions and high seismic loads, due to the regional active tectonic faults. The design of this lining included a detailed parametric study performed to handle the existing uncertainties related with ground characterization, potential deconnement and complex geological congurations.

Jun 23, 2024

By R. C. Richardson

Barite Worldwide barite production for 1985 decreased 1.3%, while US barite production increased 1.4%, according to US Bureau of Mines statistics. The increase in US production is attributed to heavy demand for oil and gas drilling during the first quarter and an unrealized heavy expected demand in oil and gas markets for the last quarter. Nevada accounted for 82.1% of the 807 kt (890,000 st) of barite produced in the US last year, according to the Bureau. Other producing states were California, Georgia, Illinois, Missouri, Montana, Tennessee, and Washington. In 1985, the US imported 1.8 Mt (2 million st) of crude barite and 64 kt (71,000 st) of ground barite. China led the way with 43.3% of the total. Imports from India accounted for 21.6%; Morocco, 15.5%; and Thailand, 5.6%. The 1.8 Mt (2 million st) of crude barite imported is an 18.8% increase over 1984. Apparent consumption of barite for 1985 was about 2.6 Mt (2.9 million st), a 15.7% increase from 1984. Due to very low drilling rig activity during the last quarter of 1985, actual consumption is probably less as crude barite inventories at mines and plants increased. According to the Bureau, 90% of barite consumed in 1985 was for the oil and gas market. Paints, rubber, glass, and other chemical uses consumed the other 10%. With the price of oil falling dramatically early in 1986, the outlook for oil and gas drilling looks to be significantly lower than 1985. This lower demand for barite, coupled with the high year-end inventories, should lower both imports and domestic production. Significant lower prices on imported barite are expected, especially from China, Morocco, and India. This also could further lower US production of barite this year.

Jan 5, 1986

By Wieda Azani, Alexander Tarigan, Willem de Beer

In block caving, the rates and sequencing of undercut production blasting, drawbell blasting, and mucking are the key levers for attempting to manage cave performance. Cave performance encompasses a range of factors, which include growth, shape and the effect of the cave on the abutments, excavations, geological structures and lithology. We compare production data in several panels in the Grasberg DMLZ and GBC block caves with the seismic response in work areas, around geological structures, and in geotechnical domains. These comparisons enable evidence-based conceptualising of the effect of production rates and mining layouts. By also considering the correlation of seismic release rates in different parts of the rock mass, the wider influence of a cave can be gauged through considering possible stress and / or deformation transfer. This concept is not novel, but it is rarely implemented in a routine fashion, principally because production data rarely are easily available. Previously, it has also been used to retrospectively compare seismic hazard between different mines. This paper discusses practical, day-to-day tools to manage seismic response to mining. Therefore, the paper presents a methodology for presenting seismic release and production rates on integrated plots at any time to facilitate quick identification of correlated spatial regions. This methodology explores the production data collection and geolocation at Grasberg, which will be described in some detail.

Apr 26, 2022

By John B. Pate

In a recent issue of the Mining Congress Journal, J. L. Gilliland discussed the relationship of air quality criteria, standards, and regu¬lations (1). As he pointed out, The Secretary of the Department of Health, Education, and Welfare is charged with issuing "Air Quality Criteria" which are statements concerning the concentration-effects relationship of an air pollutant. These "criteria" provide the states with a basis for their air quality "standards," which may lead in turn to emission "regulations." He further cites a list of major factors described by the National Air Pollution Control Administration, which must be considered in developing criteria. These are: properties of pollution; responses; measurement methods; exposure parameters; and characteristics of receptors. Although we briefly discuss the first two items, the principal concern of this paper is with the third item, the methods of measurements. In attempting to define responses, it has proven surprisingly difficult to establish a clear-cut cause-effect relationship between air pollutants and impairment of health. It is perhaps not too surprising that the ecological approach currently in fashion seems to be a much more powerful tool in defining cause-effects relationships. Without belaboring the point, we would like to point out that establishing such cause-effect relationships have tremendous legal and financial implications e.g., consider the possible establishment of such a relationship between pollution and inadvertent weather modification.

Jan 1, 1970

By James J. Scott

In 1910 the United States Bureau of Mines was created. It was the outgrowth of a social problem stemming from the fact that 25,000 men were killed in coal mining accidents for the period 1900-1910. Something had to be done and congress responded to the people's demands by creation of this new regulatory agency. At that time mine operators felt the new agency was too strict but nonetheless new rules were developed and enforced and results were obtained by the industry which reduced fatal accidents to less than 250 per year by 1970.*Social reaction by the general public brought about legislation which created the Federal Coal Mine Health and Safety Act of 1969 This legislation was a direct reaction to the Farmington Disaster. Operators and miners alike said "we cannot operate under this law. It is too strict, requirements are unrealistic, production will suffer, .there will not be any improvement in health and safety, etc." Consider the facts: 1. Health and safety have improved. The 1972 frequency and severity rate was the best ever for the bituminous coal mining industry, Figure 1. 2 .Production per manshift has dropped in underground coal mines. For example, in West Virginia from near 16 tons/m.s. in 1967 to nearly 11 tons/m.s. in 1971-72. However, not all of this loss can be attributable to the Act, but certainly some is. (2) The betterment of the safety of coal mining was a prime motivation behind the coal law and from that standpoint the law has been partially successful, but the loss in productivity has been a real burden to the mine operator. Everyone should recognize that the law says little in regard to production--it only relates to health and safety. Production is management's responsibility.

Jan 1, 1973

By William M. Kester

Finely sized Upper Freeport coals are beneficiated to reduce ash and sulfur using high-intensity magnetic separation to process both (1) raw, untreated coal as well as (2) raw coal which was pre-treated thermally with steam and air. Substantial, sulfur and ash reduction can be obtained using both approaches to magnetic beneficiation of coal fines, but evidence indicates that pre-treatment which would constitute a costly supplementary step is technically inferior to the direct beneficiation of raw, untreated coal. These bench-scale studies demonstrate that if high-intensity,; high capacity, dry, magnetic beneficiation equipment can be developed and' installed at coal burning power plants or at appropriate points in coal preparation plants substantial quantities of sulfur may be removable from coal after pulverization as a means' to reduce air pollution.

Jan 1, 1965

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010

By I. K. Gilmore

Texasgulf Inc. currently operates an open pit phosphate mine in the central coastal plain of North Carolina. The area of phosphate deposition lies within the Aurora Phosphate district which consists of an embayment which is in the center of the Neogene phosphate deposition. A variety of solid and liquid fertilizer products are produced at the Texasgulf complex. One of these products is known as North Carolina Natural Phosphate (NCNP). New potential for use of unacidulated natural phosphate, now exists in regions with acid soils due to the discovery of the findings from recent research, cost advantages, and moves to reduce chemical inputs.

Jan 1, 1995

By Y. Xi

In this paper we present an availability approach for determining the capacity of a major bucket wheel excavator (BWE) system to be used in Yuabaoshan surface coal mine in China. Based on previous time studies on other BWE systems for delay times due to internal and external causes, and a four-level maintenance and repair schedule, we develop a model taking into account all random failures and present a fast and simple solution to this highly complex problem. A procedure employing the Markov renewal theory for determination of the distribution of random failure times and failure rate of the whole system, as well as some other factors useful for calculation of the overall system capacity are discussed in the paper.

Jan 1, 1993

By K. Kim, T. M. Yegulalp

A new explanation of the scale dependency of rock strength is presented based on the theory of extremes. A brief review of past work on specimen size and strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect. It is shown that the weakest link theory is directly related to extremal statistics and that parameters of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1994

By W. S. Fyfe

Gold is mobilized or made soluble under all crustal conditions given appropriate fluid chemistry with molecules which complex gold. In the surface environment chloride, thiosulphate and a host of organics may mobilize gold. In the epithermal range bisulphide appears effective as shown by the classic studies in the Taupo volcanic zone of New Zealand. In the high grade metamorphic to igneous ranges little is know but it appears that gas molecules in the system CO2 -CO-H20-S-C1 can do the job. Precipitation may occur by changes in P-T-EL-pH or boiling where such changes influence the liquid concentration. Of the known regimes information is good for epithermal systems, poor for surface lateritic environments, inadequate for high-T systems. Gold is often concentrated in bio-systems both living and dead. The influence of biosystems is little appreciated. There is a great potential for the discovery of new types of gold deposits and in particular, gold in weathering environments, gold in very high-T environments, gold in strike-slip faults and thrust regimes, and gold as a by-product in materials like coal and other organic debris. By the year 2500 we may find our noble metal resources in the asteroids.

Jan 1, 1987

By Lynda T. Holden, Philip L. LeHoux

Barneys Canyon Mine is a 1.8 million t.p.y. gold heap leach operation near Salt Lake City, Utah. The gold recovery plant has been operating since September of 1989. Carbon elution is done at atmospheric pressure with a high temperature caustic solution. No cyanide is used in the process. Operating experience is discussed.

Jan 1, 1990

By B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 -25 m) clean coal slurry produced by the 'Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 1650 cake formation angle, provided a filter cake with 23.6 percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only 65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23 percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8 percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of 'orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By Lawson. Heather

"The purpose of this study is to explore how the geochemical and petrographic components of coal may impact its physical properties, as well as how these components correlate with a history of reportable dynamic failure in coal mines. Dynamic failure events, also termed bumps, bounces, or bursts, are the explosive failures of rock in a mining environment. These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of MSHA reportable cases. A database of variables was compiled using publicly available datasets, which included compositional geographic, strength, and Hardgrove Grindability Index (HGI) data (ACARP, 1998). Results indicate that bumping coals are less mature, lower in carbon, higher in oxygen, softer, and less well cleated than coals that do not bump. High liptinite content was found to correlate with higher average UCS values. However, no clear, direct correlation between UCS and dynamic failure status was observed. The findings of this study establish that differences exist between coals that have experienced reportable dynamic failure accidents versus those that have not. These differences are inherent to the coal itself, independent of mining-induced risk factors. Results further illuminate how compositional attributes of coal influence physical properties and begin to clarify potential links between geochemistry and dynamic failure status. Only through the better understanding of risk can more effective mitigating strategies be enacted.INTRODUCTIONDynamic failure events, also termed bumps, bounces, or bursts, are the sudden failures of rock in a mining or quarrying environment. Failure occurs when the rock’s critical bearing capacity has been exceeded and the rock fails energetically through the outward expulsion of rubblized material (Peng, 2008). These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of reported cases through the Mine Safety and Health Administration (MSHA). Much research has been devoted to the prevention of these events. The effects of overburden depth and stiffness, mine design, mining practices, and in situ stresses are well documented (Agapito and Goodrich, 2000; Brauner, 1994; Campoli and Kertis, 1987; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Lawson et al., 2016b; Mark, 2016; Newman, 2002; Peng, 2008; Whyatt, 2008). Despite these significant advancements in coal mine ground control, however, events continue to occur. Proactive risk mitigation remains an important research area. This is particularly true in underground coal settings, where the rockmass is layered, lithologically diverse, and does not exhibit consistent material properties across deposits.Many conditions have been associated with the occurrence of dynamic failure phenomena, including:"

Jan 1, 2019

By S. C. Carniglia

Bayer-process alumina hydrate becomes in turn the source of a host of special products in addition to the calcines that feed aluminum reduction cells. Though relatively smaller in tonnage, specialty aluminas serve important industrial markets in an exciting and growing variety. Production methods and applications are discussed for: (1) trihydrate as flame retardant in organic materials; (2) high-surface-area transition aluminas as desiccants and scavengers, catalysts and substrates; (3) calcines for industrial ceramics, refractories, and abrasives; and (4) tabular alumina for refractories, bed supports and other uses.

Jan 1, 1977

By Jr. Freed

Basic design features, details of the face ventilation system, roof support and Operator protection system, certified lighting, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, are reviewed. The AES is designed to help overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support and permanent roof support equipment. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1978