Search Documents

By Debasis Barman

TBM (TBM) mining in urban areas particularly under low overburden is a big challenge to design and excavate. During excavation of the Lucknow Metro project, in Uttar Pradesh, India the metro authorities encountered a design stretch where the TBM had to cross a sewer canal crossing of 15 m length under overburden of less than 1 m. Not only the stability of TBM due to uplift was of concern but also the stability of both banks. Most structures on the canal banks were non-engineered structures whose stability due to vibration of TBM was also of concern. Due to these risks, a method was proposed that met stability requirements for both ground and superstructures. The design was practical and cost effective to construct, and a collaborative exercise between the client, contractor and designer that took approximately 18 months to implement.

Jun 13, 2023

By L. G. Stolarczyk, Y. Luo, S. S. Peng

Detection and assessment of severe geological anomalies ahead of a longwall face greatly benefits the mining operation. Electromagnetic-based Radio Imaging Method (RIM) is one of the most promising geophysical methods for this task. Based on two decades of development, the latest RIM instrumentation (RIM-IV) has expanded its operational range up to 1,800ft.A site demonstration of the RIM-IV technology was recently conducted within a longwall panel. An extensive ground truth study was performed to evaluate the accuracy of the RIM survey results. This study compared the generated RIM tomograms of attenuation rate with the mapped geological anomalies. Three different approaches have been employed to examine the accuracy of the RIM results and to correlate the measured signal attenuation rates with physical properties of the coal seam. The study shows that the RIM-IV technology is able to identify and delineate those geological features that would severely affect the longwall mining operation.

Jan 1, 2004

By Morris T. Worley

Editor’s note: Mining companies doing business in Central Asia, and parts of the developing world, should look for ways to promote community development through the introduction of appropriate technology. This article should be of interest to SME members. It shows sustainable development type projects need not be massive or expensive. Smaller, utilitarian projects are equally valuable to developing communities as they seek to develop their own economic and social infrastructures. Joint Development Associates International (JDA) began humanitarian relief and community development in Central Asia in 1992, following the collapse of the former Soviet Union. Appropriate technology has played an important role in the company’s efforts to assist those segments of society that are most vulnerable to poverty and disease.

Jan 1, 2005

By Jafar Safarian, Leiv Kolbeinsen, Stian Seim, Hossein Salehi

The present work aims to investigate the link between the oxidation and reduction of a weathered ilmenite concentrate in terms of phase transitions, microstructural changes, and element distribution. An ilmenite concentrate sample was pelletized and fired at 1000 °C in air, and as a result, the pellets were oxidized. The oxidized pellets were reduced by hydrogen gas at 1000 °C, which yielded almost complete metallization of the iron content of the pellets. The ore and the pellets were characterized in each step by XRD and SEM techniques, and distribution of elements and phases were investigated. Ilmenite, pseudorutile, and rutile were the main phases detected in the ilmenite concentrate sample, and depending on the weathering degree of the particles, different fractions of the phases were identified in their microstructure. It was found that irregular rutile grains dispersed in a pseudobrookite matrix is the morphology of the oxidized ilmenite phase. However, increasing microcracks and porosities were the only microstructural changes in the pseudorutile phase after oxidation in air. Studying the specific types of the ore particles and their oxidized and reduced forms indicated that the phase distribution in the ilmenite ore particles dictates the phase distribution in the oxidized and reduced ones. Results show that the morphology of the reduced particles includes a titanium (III) oxide matrix in which reduced iron globules are dispersed.

Feb 8, 2021

By S. K. Oraee

Most management decisions at all levels of the organization are as directly or indirectly depends on the circumstance of future. With regard to predict the future events in the process of decision-making plays a main role, therefore, forecasting is very important for every organizations and institutions. There is a variety of methods to predict time series. In general, these techniques can be divided as following: statistical, artificial intelligence and analytical techniques. Two of the most common methods for time series prediction is autoregressive integrated moving average (ARIMA) and artificial neural network (ANN) methods, these methods are the subset of statistical and artificial intelligence techniques respectively. In this paper, a hybrid model of ARIMA and ANN models are employed to predict the number of fatal injuries in the USA underground coal mines. This research showed the result of hybrid model is better than split model.

Jan 1, 2011

By D. Z. Mraz, R. S. Jones

Unlike in coal mines where caving methods are used, the subsidence over potash mines in Saskatchewan, Canada, is a function of gradual mining convergence. Because of the presence of high pressure water aquifers over the evaporite salt formations, the mines have to be designed as regionally stable and no caving is allowed. The extracted area converges gradually and the convergence is mainly a function of the extraction and the mining method employed. Consequently, the subsidence rate is very slow and the bridging of the over-lying strata is a considerably more important phenomenon than elsewhere. The paper evaluates a case history of convergence and subsidence in a deep potash mine in Saskatchewan.

Jan 1, 1986

By B. Burke, R. Colquhoun, K. Thomas, R. Walton, D. Fentie

The new Roasting Facility at Barrick’s Goldstrike Mine in Nevada, U.S.A. was developed to process 12,000 tons per day of refractory gold ore. The process consists of crushing, dry grinding, roasting, extensive gas purification, calcine quenching and leaching in the presence of activated carbon. The new plant is integrated into the existing Goldstrike facility, treating ore from both open pit and underground sources. The process design, procurement, construction and commissioning of the Roaster facility was performed successfully over a 3½ year period with peaks of 400 engineering personnel and 950 construction personnel supporting the project. The US$330,000,000 project was completed ahead of schedule and under budget. The commissioning was well planned and proceeded smoothly through a rapid start-up to achieve all primary goals within three months of the start of processing of ore.

Jan 1, 2001

By Steve Kral

Commodity price down cycles are a fact of life in the mining industry. And companies pre-pare for them as best they can. Evenso, operations are still curtailed or closed during those cycles, profits shrink, layoffs are inevitable and many companies do not survive. However, one of the few good things that occurs during down cycles is the new, innovative exploration, mining and processing technologies that come about during hard times. To survive the lean times, the mining industry turns to improved technology to decrease costs and hold the bottom line. And, because mining is a cyclical business, each down cycle brings about technology improvements that carry over into the good times.

Jan 1, 2004

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. Lucy McCartan, US Geological Survey, was the chair of the SME industrial minerals technical committees. She also served as the vice chair for agricultural minerals. Other technical committee vice chairs were: •Gary Tomaino, Specialty Minerals Inc., ceramics and refractory materials. •Srinivas (Vas) Veeramasuneni, US Gypsum, chemical raw materials. •William Langer, US Geological Survey, construction materials. •Vanessa Santos, Independent, fillers and pigments. •Richard Berg, Montana College of Mineral Science and Technology, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them.

Jan 1, 2002

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021

By Anup Tiwari, Khanindra Pathak, BIBHUTI BHUSAN MANDAL

Failure of in-pit overburden dumps in open-pit coal mines causes debris to flow toward the active working face, threatening the safety of people and equipment. The evaluation of the potential mobility of failing mass will aid in hazard mitigation associated with unwarranted dump failure. The potential mobility is shown by mobility ratio (ratio of total drop between debris flow's initial and final deposition points to total travel distance) and runout characteristics. In light of above, a laboratoryscale debris flow flume was developed to investigate the effect of material gradation and slope angle on runout characteristics and mobility ratio. The total mass of experimental debris mix (Q) is fixed at 30 kg with 20% water content. Experiments at three different slope angles (30°, 35°, and 40°) demonstrate that increasing the proportion of fines in the experimental mix increases runout characteristics while decreasing the mobility ratio. The length and area of the runout decrease as the slope angle increases, while the mobility ratio increases. There is a positive correlation between d50 and runout characteristics at a fines content of 0.1Q, but a negative correlation at a fines content of 0.2Q and 0.3Q. Conversely, there is a negative correlation between d50 and mobility ratio for fines content of 0.1Q, but a positive correlation exists for fines content of 0.2Q and 0.3Q. A new index called the fine-to-coarse (F/C) ratio is used to identify the critical value of fines and coarse proportion that causes a transition from dry granular flow to fluidized debris flow.

May 29, 2023

By Bhaskar B. Thapa

The proposed Caldecott fourth bore will consist of a two lane highway tunnel along California State Route 24 near the City of Oakland. The proposed design and construction sequence for the 15-m-diameter tunnel are based on the New Austrian Tunneling Method (NATM). The initial support system incorporates combinations of shotcrete, rock dowels, lattice girders, spiles, and grouted steel pipe canopies. The final lining is cast-in-place reinforced concrete. A waterproofing membrane and drainage system are placed between the initial and final linings. State Route 24 is a lifeline route, required to be open to emergency vehicles within 72 hours after a major earthquake, defined as having a return period of 1,500 years and a peak ground acceleration of 1.2 g. Although the seismic design criteria are stringent, the design of the tunnel lining system is ultimately controlled by static ground loads in the weak rock along the alignment.

Jan 1, 2008

By W. H. Dickinson

The performance of seven antiscalants spanning a range of chemistries was evaluated for control of calcium carbonate (CaCO3) formation in gold processing applications. Three preferred chemistries were identified which provided up to 100 percent inhibition in static jar tests when applied at 30 ppm dosage. The three products were further evaluated using a model carbon extraction circuit developed for this application. The test circuit enabled direct measurement of calcium carbonate formed on the carbon from a supersaturated solution under dynamic conditions. The antiscalants lowered CaCO3 buildup on the columns by 15 - 26 percent compared to untreated controls. Impact of the antiscalants on the rate and extent of gold loading onto a carbon adsorbent was evaluated in laboratory carbon-in-pulp (CIP) studies. The antiscalants generated a 25 - 35% increase in gold loading at gold extraction efficiencies up to 65%. On-site testing at a gold processing facility demonstrated that 10 ppm of the preferred antiscalant was able to fully suppressCaCO3formation in thickener overflow water.

Feb 27, 2013

By M. A. Reyes, L. Yan

Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ

Nov 22, 2019

By James F. Kvitkovich, George V. Weisdack

Editor’s note: This is the second part of a two-part series on longwall mining in the United States. Part one was published in the December 2005 issue of ME (pp. 21-26). It provided a history of longwall coal mining in the United States. It also discussed the technology involved in the productivity gains and operational improvements. Boyd anticipates that U.S. coal production will increase by 61 Mt (67 million st) (6 percent) from 2004 to 2010. A combination of higher surface and underground mine production will be required to meet the projected market demand. Boyd’s projections of coal production by major mining methods are shown in Table 1.

Jan 1, 2006

By Martín Antonio Encinas‐Romero, Patricia Guerrero‐Germán, Jesús Leobardo Valenzuela‐García, José R. Parga‐Torres, María A. Bracamontes‐Landavazo, Agustín Gómez‐Alvarez

A study was carried out to process a sulfide mineral concentrate from Norwest of Mexico containing 97 g/t Au, 0.15% Cu, and 15% Fe. An oxidative acid pretreatment was investigated using ferric sulfate as oxidant, followed by leaching of gold with sodium cyanide. Scanning electron microscopy, SEM-EDS, and X-ray diffraction, XRD, the analysis confirms the presence of quartz and pyrite species. First, a leaching was carried out without pretreatment, at ambient conditions, T = 25 °C and P = 1 atm, obtaining only a 45.2% gold extraction. Once the presence of Fe and Cu sulfides had been confirmed, the Eh-pH diagrams were constructed for the Fe-S-H2O and Cu-S-H2O systems, where it is appreciated that pyrite and chalcocite can dissolve with high oxidation potentials and forming sulfur, oxidizing to sulfate at highly acidic conditions. The oxidized concentrate was neutralized and adjusted to pH > 10.5; it was leached at ambient conditions, at different particle sizes, 44, 37, and 26.5μm, achieving an Au extraction of 75% using a concentration of 0.5% NaCN, 26.5μm particle size, 20% solids, and P = 1atm. Then the oxidized material was subjected to different temperatures, 25, 50, and 70 °C, under the same conditions and obtaining Au extractions up to 92% at 70°C. Additionally, the leaching process was compared using an autoclave reactor at moderate pressures, obtaining an increase in the extraction of Au up to 98% in 2 h, at T = 70 °C and P = 0.62 MPa.

Jan 23, 2022

By Richard L. Gordon

At almost no time since the end of World War I has the coal industry been free from serious threats to its competitive position. At present, the critical question is whether the industry can maintain its position in the electric power market and this paper reviews the prospects in this area. Our report is part of a study, supported by Resources for the Future Inc., dealing with coal demand in general. Like most elements of coal economics, it has received much less analysis than problems in other energy sectors--a defect we felt worth correcting. We have concentrated on electric power elements of the market. The nature of the coal market makes this the natural choice. Three markets absorb over 80 per cent of coal production and are considered in our overall work. The completely excluded sectors are largely catchall categories in which coal use is declining anyway. Comparing the three markets included in the overall study, we see: modest growth is the most optimistic forecast for metallurgical coke; export growth depends to a large extent on policies of foreign governments. Electric power use, however, has rapidly grown to absorb over half of coal output and coal's prospects depend almost entirely on continued expansion of this market. Throughout the 1960's the demand for coal used to generate electrical power in the United States grew at an average rate of 6.5 per cent annually. This growth rate will be sustained until at least 1976.

Jan 1, 1971

By J. E. Friant

Until 1956, drill and blast was the only way to excavate rock. In that year, a tunneling machine using disc type cutters economically bored a small Toronto tunnel. Its amazing 105 ft/day set a new world record and set the stage for a new industry. The Disc Cutter Role in Excavation Mechanical excavation of hard rock is by now deeply ensconced in the heavy civil construction industry. All over the world, from the Swiss Alp Melange to Hong Kong Granite, to New York Gneiss, huge Tunneling Boring Machines (TBMs) create transportation, water and sewer tunnels. Powerful machines, boasting as much as 6000 hp, bore through rock, excavating in excess of 1400 tons per hour. The tool that makes this tunneling phenomenon possible is the single blade, rolling disc cutter. These hardened steel discs, from 15 1/2 to 19 inches diameter are arranged on a rotating cutterhead, to cut concentric circles in the rock. As the machine is propelled forward under great pressure, rock below each cutter is crushed. But the efficiency of the cutterhead is derived from the science of cutter spacing (distance between cutter paths). The majority of the rock excavated is not crushed, but flakes off in chips and chunks. No pick, tooth, or drag type cutting tool can duplicate the performance of a disc cutter. The economic use of drag type tools is limited to as low as 5,000 psi UCS rock strength in massive formations. In weakly bonded, foliated rock, drag tools do better, but are still limited to rock generally less than 15,000 psi.

Jan 1, 2002