Search Documents

By R. B. Hopler

Explosives R&D has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. This process continues at an accelerated pace today due to the tools presently available to the explosives and mining industries.

Jan 1, 1993

By J. L. Fuentes

The so called 'SISCOM' is a General Purpose, microprocessor-based Monitoring and Control System, developed by AITEMIN to meet the requirements of Spanish Mining Industry in - the field of automation and data -transmission. Typical applications -are automatic control of pumps, compressors, fans and conveyors, as well as environmental monitoring and production monitoring. In relation with the last, the - System has been succesfully installed in a full section roadheader and in a mechanised steep coal face. In both cases, the main objective is to get information about running times, down times and causes, -and monitoring of other important parameters such as ventilation, methane content, power consumption..etc. Measurements concerning the face behaviour from a geomechanical point of view are also monitored. These are different pressures and stresses. All data is transmitted to the - surface and on-line analysed by a -desk-top microcomputer. The paper shows the system structure and the requirements that have - been considered on its design. Attention is given to the mechanical data acquisition problem, involving special development of some transducers. The information provided by the surface microcomputer is shown and its utility discussed.

Jan 1, 1986

By Raphael G. Kazmann

Water occupies a dual role in our industrial society. It is the indispensable raw material, essential to life itself. It is equally an industrial nuisance, interfering with the production of industrial minerals, making construction difficult, flooding valuable land, and generally producing problems because it is in the wrong place at the critical time. The legal position of water as a nuisance, and the counter measures to be taken, have been well established procedures for determining the responsibility for damage caused by water, and the organization of drainage districts and flood control and levee districts have been legally tested many times. Thus there is rather adequate legal doctrine concerning water, the common enemy. But recently efforts have been made to regularize the position of water as a useful, industrial, commodity. Such laws are not new to the West, where the doctrine of appropriation for beneficial use is slowly becoming the water law. Elsewhere the University of Michigan has produced a "model" water law and efforts are being made to induce all of the states to use this law, or a slight variation of it, as the basis for legislation. There are many serious criticisms of the proposed "model"-law, and the writer strongly opposes many of the provisions. But the fact remains that water is, in itself, so useful and essential that laws have been, and will be, passed to insure the orderly development of our water resources and to prevent waste. The, most important aspect of these "water-use" laws is that, wise or unwise, the existing laws and the proposed laws have been "water oriented". "Water oriented" means that it has been tacitly assumed that the beneficial use of water, either surface water or ground water, is the overriding consideration.

Jan 1, 1960

By R. B. Massy-Greene

Project engineering and development is a process of optimisation of capital, operating and financial costs, and extraction rates in the light of current and forecast economic conditions for the sale of the product. The aim of the process is to maximize financial returns to the sponsors (project owners) within many often conflicting constraints. Thus, the sponsor's engineering and financial staff have a common goal, with performance measured in financial terms. Consequently, each group must be aware of, and responsive to, the constraints imposed upon the other. For financial staff, the increasing size and complexity, and escalating capital costs of new ventures have required them to seek finance in larger amounts, and by non-traditional methods. In addition, senior management are requiring indications of the availability of finance as a pre-requisite to a decision to commence project development activities.

Jan 1, 1982

By Stefano Ceccotto, Eugenio Trussoni

"INTRODUCTION Contemporary city is made of layers. Physical structures layers (built fabric, residential, commercial industrial etc. ), infrastructural layers (below and above ground), “green” layers (parks and open spaces), and also informational layers, i.e. connections, links, between sectors of the city and other territories. The “city of layers” concept represents the exercise of “rebuilding the city” per each layer, highlighting those physical built structures that are functional to define a relation. For example, if consider the “connection” relation, the city is re-designed by considering only transportation built structures. The layer obtained in such fashion is hence the “transportation” layer, including below grade infrastructures (subways) and above grade lines (rail, bus, tramways etc.), as below shown in Figure 1.In this sense, the contemporary city is represented by separate constructs assembled together according to a specific functionality (e.g. “connection”). As a consequence, the relation between what is built underground, and the related above-ground development, can be perceived in his most evident appearance. What could happen within the contemporary city if the planning process would begin from below to above and not vice-versa?INTERACTION The question risen in the introduction is strategic when approaching the difficult task of designing (or re-designing) a multi-level organism like the contemporary city. Nowadays, the theme of integration between underground and at-grade master planning has become the subject of many urban renovation projects, where the design process has begun within the transportation layer, underground, and further developed by interacting with at-grade structures already existing or in phase of design.A series of case studies where below/above interaction plays a key role in the project will be further analyzed. Moreover, it is relevant to understand the mechanics of an urban transformation process that originates within the transportation layer and ends up with the design of entire sectors of the city. The Transit Oriented Development approach is a useful tool to clearly understand such transformation process. TOD has become, in particular in the last decade, one of the most effective tools for urban design, in order to solve simultaneously the many different instances related to transit planning, urban design and real estate market."

Jan 1, 2016

By Zohreh Kazemi Motlagh, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Five-element style deposits are unusual hydrothermal systems that are typically characterized by a nickel-cobalt-arsenic- silver-bismuth metal assemblage. This mineralization is often represented by abundant native silver, arsenic, or bismuth, and followed by nickel, cobalt, and iron arsenides (skutterudite, safflorite, nickeline, rammelsbergite, and lollingite). The Black Hawk district in Grant County, New Mexico is one of the few examples of this mineralization style in the United States. Despite the differences in formation temperature, depth of emplacement, and host rocks between five-element style deposits worldwide, there are commonalities in mineralogy, ore texture, and composition. A detailed exploration of the native metal and arsenide phases will be performed to compare ore forming fluids between systems and the effects on styles of mineralization and paragenesis, as well as to aid in broader classification of the deposit style. Mineralogy and mineral relationships of the Black Hawk District and other five-element deposits worldwide will be characterized by reflected light petrography, scanning electron microscopy, X-ray diffraction, and electron microprobe analysis. Mineralogical phase diagrams will be generated to better understand the driving processes and evolution of the systems through native metal and arsenide precipitation.

Feb 1, 2024

By James R. Jones

It has been 2-1/2 years since the Congress passed the Surface Mining Control and Reclamation Act of 1977 (PL95-87) the Office of Surface Mining every deadline specified in the Act. Hopefully the Congress will begin to realize that specifying unrealistic deadlines does not accomplish the end desire of legislation any sooner -- it only adds to the confusion, and actually hinders orderly, efficient progress. OSM has been sued by all categories of involved parties -- environmental activitist organizations, the states, and the coal operators. This situation has resulted for two reasons: (1) insufficient time was allotted by the Congress to properly develop the regulations and program, and (2) OSM?s philosophy that it must dictate every detail of reclamation operations from Washington, even though many of its people are inexperienced with coal mining. These law- suits are now demonstrating their value. OSM is showing signs of "pulling-in-its horns" and, hopefully, will approach the revised regulations in a more realistic fasion.

Jan 1, 1980

By H. R. Green

The design of slurry launders has usually been based on strictly empirical concepts. An examination of the most common procedures reveals that they do not account for many of the variables that are recognized as Significant for slurry transport. These may include flow rate, volume concentration of solids, solids specific gravity, solids size distribution particle shape, launder geometry, and roughness of the wetted surface. It was decided to develop a design procedure, which would accomplish two things: First: Take into consideration most of the known significant variables and systematize the procedure to assure consistent results. Second: Provide a rational basis for examining and utilizing operating data to refine and improve the system. To accomplish this, it was necessary to develop a basic design concept. This concept has been developed through a complex development history, and yet still appears workable and technically sound. That concept may be outlined as follows: First: The solids transport velocity is the fundamental basis for slurry launder design. Second: The stream configuration, hence the launder size, is integrated with the solids transport velocity so that the actual stream velocity exceeds the solids transport velocity. Third: The launder slope is that which will achieve the required actual stream velocity. It was originally planned to utilize a series of charts and nomographs for the design procedure. A nomograph, based on data given in Taggart's Handbook of Mineral Dressing (1), was developed to determine the solids transport velocity. The velocity thus determined was used with Manning charts to determine the launder slope .and configuration as though the fluid were water. It was planned to utilize a "slope adjustment factor" to increase the slope to compensate for the apparent viscosity of the slurry. All attempts to develop a suitable correction factor failed. This failure was principally due to the complex relationship of viscosity to the required slope. It was then decided to revise the entire approach. Specifically, the present procedure is based on the Darcy-Weisbach flow equation, which is rationally preferable to the Manning equation. The Camp (2) equation is used for the solids transport velocity. The necessity of reference to the Moody curves for the Darcy friction factor is avoided by using the Colebrook and White (3) equation. The resulting mathematics require iterative solutions for several of the unknowns.

Jan 1, 1978

By J. T. Hanks

Process development is one of the principal tasks required in the course of turning an exploration discovery into a mine. Exploration geologists should have an understanding of the more important metallurgical processes and the test work required for each process. The paper discusses the important metallurgical processes, the test work and sample requirements for each, and the costs and time requirements to accomplish the testing. The limitations of reverse circulation drill samples for metallurgical testing are discussed. The level of process definition required to support engineering studies: scoping, pre-feasibility and feasibility studies are also described.

Jan 1, 1997

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By C. W. Schultz

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained.

Jan 1, 1991

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sink times were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1% and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying and dumping of coal products by comparison to airborne dust capture from sprays.

Jan 1, 2013

By Richard H. Lindgren

I appreciate this opportunity to discuss with you OPIC's new policies designed to assist U.S. minerals companies in developing new sources of minerals overseas. A comparison of recent figures on U.S. investment in mineral exploration, development and production gives results which are remarkable --and disturbing. Through the 1960's the flow of U.S. foreign direct investment in mining and smelting in the developed and less developed countries were nearly equal. However, by 1973, roughly 80% of all exploration expenditures by mining companies was taking place in the developed countries and principally in the U.S., Canada and Australia. Clearly it is to the interests of both the developing countries and the United States to put these figures back in better balance. As you may be aware, the administration as a whole is examining systematically what can be done by government to reduce the disincentives and increase the incentives to mineral investment in the less developed countries --the LDCs. A subgroup of the National Advisory Council chaired by the Treasury Department has been formed to coordinate U. S. Government policy and program efforts relating to mineral and energy development in these countries. Among other matters, this subgroup will examine how public policies could positively influence the private investment decision-making process in the minerals industry.

Jan 1, 1978

By Mike Hall, Tim Kelly, Mohammad Reza Jafari, Ulf Georg Gwildis

"Qatar’s capital Doha is undergoing major infrastructure improvements including a multiphase stormwater management program. Although located in an arid climate, Doha experiences flooding during rainfall events. Dewatering operations and rising groundwater levels add to the management needs. To address those needs, construction of the Musaimeer collection tunnel along Doha’s southern rim is being followed by a marine outfall tunnel connecting a pump station to a dispersion field 10 km offshore. Qatar’s geology is characterized by sabkha deposits, a series of predominantly weak and karstic rock strata that creates challenging conditions for mechanized tunneling, as highlighted by the uncontrolled flooding of a tunnel boring machine (TBM) used on the Doha Metro tunnels. Risk associated with these challenges is magnified for the outfall tunnel by drive length, sub-sea elevation, and a single access point. This paper describes the outfall exploration strategy and design decisions made in light of experience gained during the collection tunnel construction. CONTEXT – STORMWATER MANAGEMENT PROGRAM Qatar has an arid climate with an average annual precipitation of less than 100 mm. Precipitation is mostly confined to the winter months when rare, but occasionally heavy rainfall events easily lead to flooding in Doha’s metropolitan area. Its coastal location and flat topography a few meters above the sea level mean that the depth to the groundwater table is generally shallow. The karstic aquifers in the regional dolomite and limestone series contain groundwater of high salinity, which is not suitable as a potable water source. For supplying Doha’s population of more than 900,000 (2014) with potable water, the Ras Abu Fontas seawater desalination plant is operated about 10 km south of the city. This potable water production capacity is crucial for Doha’s development and – in conjunction with overirrigation and leaking sewage tanks – is also the root cause for rising groundwater tables that have been observed over the past years."

Jan 1, 2016

By B. Hearn, Malcolm J. McPhersqn

Since 1993 Inco Ltd. has been using wet shotcrete at Stobie Mine. Through an evolving process the mine has reduced the thickness and fiber content of its steel fiber reinforced (sfr) shotcrete. However, the shotcrete support is used without any other type of ground support. A process referred to as bolt less shotcrete. Boltless shotcrete is used as the primary ground support method in development headings when the sub level caving front passes through the development drifts which now serve as migrating ore draw points. Although there are references of drifts and tunnels supported by shortcrete only, written accounts are rare. The empirical nature of most underground support designs makes them of limited value in a boltless environment. Considerable amounts of material testing and insitu trials have been completed in order to estimate material property strengths. Material testing, for adhesion, flexural strengths and compressive strength along with observational insitu data have been used to evaluate the performance of shotcrete. Punch tests on panels have also been undertaken in order to gain insights on the limitations of the two dimensional testing common to the laboratory. All these design aspects have been successfully utilized to design an efficient ground support process.

Jan 1, 1998

By P. A. Delfosse

Numerous terms are used for rocks containing calcium carbonate so that confusion frequently occurs in the common language. Chalk and marble are two extremes among a wide variety of carbonate rocks including limestones, marls, travertine and other calcareous materials. We will deal mainly with the purest types of natural calcium carbonates which are widely used today in many industrial applications.

Jan 1, 1986

By Fouad Faraj, Julian M. Ortiz

Within the natural resource industries, there is an increasing amount of data and number of variables being recorded when sampling a site. This has made multivariate geospatial datasets more difficult to analyze, in particular the definition of estimation or simulation domains used in geostatistical analysis. Establishing these domains is typically the first step for any subsequent geostatistical workflows or modeling. Domains are traditionally established using categorical data such as lithology, mineralization, or alteration from geological logging and are aimed at identifying distinct populations with particular geological, spatial, and statistical features. The manual logging process is time-consuming and costly but is required because defining geologically homogenous volumes is crucial for the planning, extraction, and processing of natural resources. Classical clustering methods have aided in analyzing the multivariate datasets, but the resulting clusters from these methods do not correlate well with geological logging and do not allow practitioners to input their knowledge of the domain in the clustering process. In this work, a simple unsupervised classification workflow is presented which allows the practitioner to input domain knowledge by selecting relevant variables to cluster reasonable geological domains. This can be used as a tool to aid the manual logging procedure or as a tool to establish domains for different uses such as defining zones with different rock hardness distributions which allows the corresponding volumes to be sent to appropriate mills for efficient mineral processing. The performance of the workflow is assessed on a mining dataset using the geochemical information and validated with the geological logging.

Apr 16, 2021

By R. L. Grayson

Evidence has accumulated indicating that cultural change toward safer workplace behaviors is beginning to occur systematically in the coal industry. Through a range of programmatic mining company successes, enforcement and litigative actions, economic responses to competition, and integrated efforts by federal and state agencies, a broader participation of safety and training professionals is being achieved to address prioritized workplace problems at mines. Small steps in workplace-related improvements have been realized already, but the trends in industry safety statistics, coupled with focused programmatic initiatives, indicate that more definitive and systematic steps are occurring to improve safe behavior in the workplace routinely.

Jan 1, 1996

By M. R. Grundy

The Robinson project is based on the porphyry copper and gold deposits in the Robinson Mining District, near Ely in Eastern Nevada. The district was mined from the late nineteenth century to 1978 by Kennecott Copper Corporation and its predecessors. Operations ceased when falling copper prices in the late 1970's made their outdated mill and smelter complex at McGill uneconomical. In October 1991, Magma Copper Company (Magma) acquired the many claims that cover the known porphyry copper deposits in the district These occupy a disturbed area about nine miles long and three miles wide between the towns of Ely and Ruth. Magma proposes to build a copper / gold mine and concentrator and expand the existing gold leaching facilities. Several pits, previously mined by Kennecott Copper Corporation, will be enlarged; the use of larger, more modem equipment will result in higher productivity and lower operating costs in general. ICF Kaiser Engineers, of Oakland, California, were awarded the con-tract for detailed design of the process facilities, which was essentially complete by the end of 1993. The project at present is awaiting completion of the environmental permitting process; state air and water permits are in hand, and the Bureau of Land Management's (BLM) current schedule indicates that the final obstacles to construction will be cleared by early fall of this year.

Jan 1, 1994

By Kapila Pathirage, Michael S. Schultz, Gregory Sanders, Ulf G. Gwildis

Adequate understanding of the subsurface conditions along the alignment of a planned tunnel is key for managing project risk. For achieving this understanding, geotechnical borings are conducted during design. Where their spacing cannot reduce the risk of encountering differing site conditions (DSC) in-between borings to an acceptable level, supplemental exploration methodologies or data evaluation approaches may be required to bridge the data gap. This paper compares the exploration design approaches of recent tunnel boring machine (TBM) and microtunnel boring machine (MTBM) projects in the quaternary deposits along the Eastern Seaboard, the glacial geology of the Pacific Northwest, the sedimentary rocks of the South, and metamorphic rocks in western Germany, describing their respective effectiveness of managing DSC risk.

Dec 1, 2022