Search Documents

By Chapman Young, Donald E. McCarthy

Many hard rock tunneling projects, where the majority of excavation can be accomplished with TBMs, will still require considerable specialized excavation which can not be done with a TBM. This secondary excavation, involving cross cuts, galleries, flattening of the invert, increases in bore diameter, et cetera, may be accomplished with conventional drill and blast, applied on a small scale and usually with fracture control techniques, or with mechanical splitters. The problems of using explosives in many of these cases and the high cost of mechanical splitting excavation make the consideration of other approaches attractive. The PCF rock excavation method, which has recently been reduced to commercial practice for mine-development excavation, offers an attractive alternative to drill and blast and mechanical splitters. With the PCF method the rock is excavated utilizing a small-charge, propellant-driven, controlled, penetrating-cone fracture process. Excavation is carried out continuously by combining the PCF hardware with integrated mucking capabilities on a carrier which remains at the excavation point. In addition to the benefit of providing for complicated excavation geometry, the PCF method also causes minimal damage to the remaining rock which will significantly reduce ground support requirements. In very bad ground, the continuous nature of PCF excavation allows ground support to be applied as limited sections are exposed thus reducing both the duration and extent that the ground would be free to move. Data on PCF excavation parameters, as measured in actual mining operations, indicate that crosscuts, galleries and the like could be excavated at considerable cost savings compared to drill and blast or mechanical splitters.

Jan 1, 1995

By John C. Galloway, Heinz G. Leistner

ACKNOWLEDGEMENTS The investigations described in this paper were supported by contracts with the Defense Nuclear Agency (DNA) under direction of Lt. Col. John Galloway, and by Boeing Company research funds under supervision of James Wooster. Other engineers of The Boeing Company who contributed to the work of this investigation were Don Armitstead, John McAvoy, and Tom Day. INTRODUCTION In this paper, we are describing a current concept for placing intercontinental ballistic missiles (ICBMs) in sites deep underground to be used as a strategic Future Secure Reserve Force (FSRF). The objective of such concepts is to utilize soil and rock cover to protect high value strategic weapons from destruction by nuclear attack. The burial deep underground achieves two purposes. First, it imposes a miss distance upon the attacking weapon equal to the depth of burial minus any penetration capability the weapon might have. This tends to offset increasing accuracy of weapon delivery. The other purpose is to absorb as much of the weapon's energy as possible, thus reducing the effects of powerful weapons. This use of soil or rock cover over military facilities began with the development of man's capability to loft projectiles. Until recently, underground military installations, by their nature, performed defensive functions. Since they are not mobile and their weapons in the past had very limited range, an enemy would have to approach them before an engagement could take place. Thus, they were often used to control "choke points" on sea lanes as in the case of Gibraltar or

Jan 1, 1979

By R. S. Datta

In the article "Concentration of Oil Shale,"(1) Dr. N. Arbiter stated, "One of the major factors in the delayed utilization of oil shale as an energy raw material is the low grade or content of hydrocarbon (kerogen) in oil shale as compared with coal and even more so to the liquid and gaseous fuels. " When the availability of high-grade deposits decreased, mineral industries started adopting prebeneficiation procedures for the low-grade deposits. This practice, which is becoming standard in these other industries, has been largely overlooked by the oil shale industry in its drive to produce oil from oil shale. If a major portion of this mineral matter can be removed, there can be potentially large savings in the capital and operating costs of oil shale retorts. Moreover, the environmental impact, associated with recovering the shale oil, could be reduced considerably. In 1980 Roberts & Schaefer Resource Service (RSRS) completed successfully the first set of demonstration runs with a 20-ton oil shale sample from Cathedral Bluffs (C-b tract), Colorado. This relatively low grade (~12 gpt oil content) oil shale was beneficiated applying the Dutch State Mines Heavy Medium Cyclone process. (2)

Jan 1, 1985

By V. T. McLemore

"Lindgren (1933) defined a belt of alkaline-igneous rocks associated with large quantities of gold and rare earth elements (REE) that extends from Alaska and British Columbia southward into New Mexico, Texas and eastern Mexico. The North American Cordilleran alkaline-igneous belt since has been exploited for numerous types of mineral deposits. In New Mexico, Mid-Tertiary alkaline to calc-alkaline rocks are found with seven types of deposits in these districts: (1) polymetallic epithermal/mesothermal veins, (2) gold-bearing breccias/quartz veins, (3) Cu-Au, Au and Mo porphyry deposits, (4) skarns and carbonate-hosted deposits, (5) iron skarns and replacement bodies (with some gold), (6) gold placers, and (7) Th-REE (with some U, Nb) epithermal veins. Some of New Mexico’s largest gold and REE deposits are found within this belt. Their origin is not well understood, but a compilation of new data (age dates, isotopic and chemical analyses) allows for a better understanding. The diversity of igneous rocks and associated mineral deposits along this belt suggests that this region is characterized by highly fractionated and differentiated; multiple pulses of magmas and involves both upper mantle and lower crustal sources. Once magmas and metal-rich fluids reached shallow levels, local structures and wall rock compositions determined distribution of and final style of intrusions and resulting mineral deposits. INTRODUCTION Lindgren (1933) was one of the first geologists who noted that a belt of alkaline-igneous rocks extends from Alaska and British Columbia southward into New Mexico, Trans-Pecos Texas, and eastern Mexico (Fig. 1) and that these rocks contain relatively large quantities of gold, fluorine, zirconium, rare earth elements (REE), and other elements. Since then, the North American Cordilleran alkaline-igneous belt has been explored and exploited for numerous types of mineral deposits, especially gold. The North American Cordilleran alkaline belt is a north-south belt of alkaline igneous rocks and crustal thickening, roughly coinciding with the Great Plains physiographic margin with the Basin and Range (Rio Grande rift) and Rocky Mountains physiographic provinces (Mutschler et al., 1985, 1991; Bonham, 1988; Thompson, 1991a; Richards, 1995; McLemore, 1996; Jensen and Barton, 2000; Kelley and Luddington, 2002). Deposits within this belt have produced significant amounts of gold in the United States and Canada and include Cripple Creek, Colorado (702 metric tons of gold production), Black Hills, South Dakota (235 metric tons gold production) and Landsky-Zortman, Montana. In New Mexico, the North American Cordilleran alkaline belt extends from the Sangre de Cristo Mountains near Raton, southward to the Cornudas Mountains, in the northern Trans-Pecos alkaline belt (Fig. 2). The alkaline-igneous related mineral deposits in New Mexico have been referred to as Great Plains Margin (GPM) deposits by North and McLemore (1986, 1988) and McLemore (1996, 2001). Alternative classifications by other workers include Au-Ag-Te veins (Cox and Bagby, 1986; Bliss et al., 1992; Kelley et al., 1998), alkalic-gold or alkaline-igneous related gold deposits (Fulp and Woodward, 1991a; Thompson, 1991a, b; Bonham, 1988; Mutschler et al., 1985, 1991; Richards, 1995), porphyry gold deposits, and the North American Cordilleran belt of alkaline igneous rocks (Woolley, 1987; Mutschler et al., 1991)."

Jan 1, 2015

By J. Snowberger III

Rhenium is a valuable and extremely rare chemical element with unique chemical properties. It is extracted commercially as a byproduct from the processing of molybdenite associated with porphyry copper ores. There is a present interest in recovering rhenium from copper pregnant leach solutions (PLS) produced by copper heap and stockpile leaching. These solutions contain rhenium at very dilute concentrations, typically in the 1 mg/L concentration range. This paper describes laboratory column ion exchange experiments to extract rhenium from these solutions using weakly basic anion exchange resins and actual plant PLS from two operating mines. The dynamic loading and elution behavior of Re on Purolite® A170 and A172 is discussed.

Feb 23, 2014

By M. R. Yalamanchili

The in-situ FTIR/IRS technique has been used to spectroscopically characterize interfacial water near a hydrophilic surface. Interfacial water was examined spectroscopically over known distances from the surface of a silicon single crystal by appropriate design of the geometry and optics of the internal reflection system. The in-situ FTIR/IRS spectra of interfacial water were examined by consideration of the 0 -H stretching region (3000 -3800 cm-1) associated with the vibrational spectra of water. The broad peak: in this region which describes the interfacial water structure was deconvoluted in order to isolate the overlapping spectral features of the interfacial water. Preliminary spectral results indicate the prevalence of an ice-like water structure (-3200 cm-!) at the silicon surface. Importantly, it appears that the interfacial water structure may extend a considerable distance (several tens of molecular layers) from the surface as established from the spectroscopic depth profile measurements which show that the free OH stretch at 3600 cm-1 becomes very significant at distances from the surface exceeding 400 nm.

Jan 1, 1995

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By J. Andres

"Freeport-McMoRan’s Sierrita operations refines molybdenum disulfide in a ferric chloride leach to remove impurities. To understand bottlenecks in the leach process and the true capacity of the leach system, a cross-functional team was established to look at theoretical models, kinetics of the leaching process, equipment limitations and operational strategies. A series of in-plant tests were run which resulted in a road map for improved throughput. INTRODUCTION Molybdenum, a vital component in the steel industry, is often found in nature as molybdenum disulfide (MoS2). Molybdenum disulfide deposits can exist as standalone components in an ore body, or can also be found within copper porphyry nodes. Processing for these copper/molybdenum porphyry ore bodies involves a first stage of flotation to produce a bulk concentrate before separation of the copper and molybdenum concentrates in a second stage of flotation. In this second stage of flotation, a reagent is added to suppress the copper particles, while allowing the molybdenum disulfide particles to remain hydrophobic and continue to float. This separation is very good at keeping the molybdenum out of the copper concentrate; however a portion of the copper continues to float through the circuit. As a result, there is typically some amount of copper in the final molybdenum concentrate. This copper must be removed in order for the molybdenum disulfide product to meet product quality specifications. Once the raw molybdenum disulfide product has been made, a separate process must be applied to remove any copper, lead, or other impurities remaining in the concentrate. This process usually involves the selective leaching of impurities out of the bulk solid. Gupta mentions three specific types of leaching agents, sodium cyanide, ferric chloride, and hydrochloric acid for the removal of sulfide impurities. Sodium cyanide is useful for the removal of copper compounds such as bornite, covellite, and chalcocite.1 Sodium cyanide solution dissolves these copper compounds, and the remaining molybdenum solids are filtered to produce a pure molybdenum concentrate. Ferric chloride works similar to that of sodium cyanide, but is particularly efficient in removing chalcopyrite and galena compounds. These compounds are easily chlorinated at elevated temperatures, producing copper chloride and lead chloride, through the reactions presented below:"

Jan 1, 2015

By M. Stuart

The copper-silver-mercury orebody of Gortdrum Mines (Ireland) Limited is located 3 miles north of the town of Tipperary in the Republic of Ireland. A drilling programme from 1964 to 1966 delineated an ore¬body of 4.19 million tons of copper ore assaying 1.19% Cu and 0.75 ozs per ton Ag, which could be mined from an open pit. Testwork having shown that the ore was amenable to conventional flotation techniques, it was decided to build a concentrator of 500,000 tons ore per year capacity. Stripping of the open pit commenced in 1966 and in the autumn of 1967 the concentrator started up. The first shipments of concentrates were made to the smelter in Europe in late 1967. In the spring of the following year, word was received from the smelter that these early shipments contained between 1% and 2% Hg, and that the smelter could not accept further shipments of this quality.

Jan 1, 1973

By A. W. Khair

Surface subsidence is a phenomenon mainly associated with longwall mining, although it can also occur if the coal pillar left to protect the surface deteriorates with time and results in the collapse of the room and pillar system. A method has been developed that utilizes physical mine models and laser holographic interferometry. This method is capable of measuring displacements as small as 5 micro- inches by means of generating displacement contours on a surface, even that of granular materials. Analysis of subsidence in room and pillar mining using models of various extraction ratios ad overburden depths along with two different types of overburden model material (sand and gelatin) has been made. The sand represented the extreme brittle conditions of geologic material while the gelatin represented visco-elastic behavior of geologic material. This paper deals with the analysis of data which has been gathered up to date, and mainly associated with the use of sand as an overburden model material. The analysis included the effect of variation of geometric parameters on surface subsidence. Among these parameters are: variation in seam depth and thickness, surface and seam inclination, and extraction ratio.

Jan 1, 1984

By R. Fernando

"The Office of Mine Safety and Health Research (NIOSH-OMSHR) currently is leading an effort in the development of the next-generation self-escape apparatus as part of the research imperative directed by the MINER Act of 2006. A multifaceted contract program over the past 3 years delivered key components and base breathing modules to form the basis for developing backpack and vest-style versions of dockable self-contained (closed-circuit) self-escape respirators with hoods (CCMERs). This paper outlines the current status in developing the CCMER that incorporates a docking and switch-over valve (DSOV) for seamless transfer from one breathing device to another, and a hood with an inner mask and speech diaphragm (HMC) for ease of donning, ease of use, and communication ability. Three versions of the CCMER are being pursued, namely: the CCMER-B, which can be worn as a backpack and incorporates the features of a miner’s belt; the CCMER-V, which is worn similar to a miner’s vest and attaches to a miner’s belt; and the CCMER-C, a breathing module cached along the escape route that can be docked to the -B and -V versions. Human factors considerations are a key element in the CCMER design, as it is to be continually worn by the miner while underground, and must be readily accessible for deployment when needed. The CCMERs are designed to be capable of being certified to 42 CFR part 84 standards, including sub-part O for mine use, and to meet MSHA permissibility regulations for use in underground mines. They are sized for sufficient oxygen capacities (Cap 2 and Cap 3 as defined in sub-part O) to yield a duration that is of practical use in a mine escape scenario. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) is leading the development of self-escape apparatuses to provide breathing gas to mining personnel operating in the event of an emergency in various capacities underground in environments containing hazardous gas components. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) and input from the mining community called for the need to move Self-Contained Self-Rescuer (SCSR) technology to a next-generation status. In response to this need, NIOSH’s Office of Mine Safety and Health Research (OMSHR) established a strategic plan to develop key components and devices with help from external experts knowledgeable in breathing apparatus designs. The US Navy was identified as a key expert in this field through its extensive experience in diving apparatus and life support systems, and development work commenced through Inter-Agency Agreements with OMSHR. A contracts program was also launched with industry experts specializing in this field. This paper outlines the current status in developing the Next-Generation Closed-Circuit Mine Escape Respirators (CCMERs) that could be used for surviving and escaping from a mine following an emergency that renders the mine atmosphere irrespirable."

Jan 1, 2016

By Laurent Rus, Bakar Amara, Jean Habimana

The La Fontaine Tunnel in Montreal, Quebec is currently undergoing major structural rehabilitation work and systems upgrade work to comply with current codes, standards and best practices in fire life safety and to extend its lifespan of this 55-year-old immersed tube tunnel for at least another 40 years. The paper discusses design consideration of ongoing works that include structural analyses to evaluate repair strategies for the post-tensioned reinforced caissons, the scheme to repair two leaky joints between caissons, the design of passive fire protection that involved in situ and real scale laboratory tests, and other tunnel systems upgrades.

Jun 13, 2023

By B. A. Barnum

The Chino mine is an open pit copper mine located in southwestern New Mexico, at an elevation of 1890 m (6200 feet) above sea level, approximately 117 km (70 miles) north of the Mexican border. It is owned by Chino Mines Co., a Phelps Dodge Corporation-Mitsubishi Minerals partnership, and is operated by Phelps Dodge Corporation. As part of an effort to maximize production and minimize costs, a computerized truck dispatching system was approved for purchase and installation at the Chino mine in March. 1984. Modular Mining Systems, Inc. was commissioned to install their system, trade named DISPATCH. The system installation was completed and operation began in July, 1985. Installation and operation of the system has presented some interesting challenges and problems, which have been overcome, resulting in increased productivity for the haulage truck and shovel fleets.

Jan 1, 1987

By David Muir, Slobodanka Vukcevic

Gold is commonly associated with copper minerals, particu­larly in the more geologically recent rocks of Northern Australia, Chile and the Pacific Rim. Traditionally, oxidised copper-gold ores are selectively mined and processed for gold by cyanidation, ensuring that levels of reactive copper in the ore are kept low to minimise cyanide consumption; whilst sulphide copper-gold ores are floated and gold is ultimately recovered as the by-product from copper smelting and refining (La Brooy, 1992). Very few process­ing options exist for treating copper ores which cannot be selec­tively mined or floated, and for treating floation tailings which often contain significant gold (Muir et.al.,1989). The ammonia-cyanide leach system stands out as a unique method of selectively extracting gold without copper using economic levels of cyanide (1-2 kg/t NaCN) and ammonia (1-5 kg/t). Although first patented in 1904, it proved difficult to control and predict per formance with different ores. However, recent research and development in Western Australia by Ruane (1991), Hayes and Corrans (1992), La Brooy et.al.(1991), Muir et.al.(1993), Muir and La Brooy (1993), has led to an under­standing of the mechanism, and the commercialisation of the process at the Paris Dump (W.A.), Akjoujt (Mauritania), and in the Eastern Transvaal (Laxen,1994). Efforts are now underway to pilot and develop a tailings treatment plant at Telfer following successful laboratory trials. To date, process optimisation has relied on trial and error and large numbers of tests covering a range of conditions. Thus the results are specific to the ore. At Murdoch University, process optimisation is now focused on measuring and control­ ling Eh, pH, NH3 [Cu(II)], and Cu-CN species at the optimum levels identified from the recent mechanistic studies. In this way, the optimum composition required to process any ore should be readily established and maintained.

Jan 1, 1995

By Gary L. Mowrey

Visible and sometimes audible indications of excessive underground rock pressure such as pillar fracturing, squeezes on chocks, and "roof talk" are familiar to mining engineers. Such signs often precede rock failure on a larger scale and therefore may be used as a warning. Nevertheless, these subjective observations do not provide an adequate means of evaluating the existing rock pressure conditions in a mine. One method which appears to be extremely promising in determining the stability of geologic structures in general is that of monitoring their associated micro seismic activity. Mining engineers generally agree that during the process of rock deformation and failure small-scale seismic ("microseismic") vibrations are produced in the rock itself. These transient vibrations propagate through the rock structure and may be detected at a considerable distance from the failed rock by employing suitable electronic monitoring equipment. Hardy (1) has presented a detailed review of microseismic research in the mining, petroleum, and geoscience areas, and it is apparent that relatively little application of micro seismic techniques have been made in coal mines. This is especially true in North America since here most coal mines are fairly shallow and consequently are not generally subjected to excessive stresses. Furthermore, strict Federal and State mining laws limit the use of electrical equipment in coal mines complicating the use of the necessary monitoring facilities. In terms of both mine safety and economics, monitoring microseismic activity appears to be invaluable in the detection and location of over-stressed pillars and unstable roof conditions caused by development and production work. In 1970 The Pennsylvania State University Rock Mechanics Laboratory became involved in a research project, sponsored by the U.S. Bureau of Mines, to investigate the feasibility of using microseismic techniques to detect and to locate potential regions of instability around a longwall coal-mine operation [Hardy and t10wrey (2); Mowrey (3)]. In this study geophones (velocity gages) located in an array of shallow boreholes drilled from the surface above the active area of the longwall were employed to detect microseismic activity, and a mobile micro-seismic monitoring facility was used to condition and record this data for later analysis. This project is unique in that measurements were made from near-surface geophones rather than geophones installed on the mine itself. Two advantages are apparent, namely that (1) there are no electrical limitations on the monitoring system and that (2) mining operations can continue normally because there is no monitoring equipment or cables in the mine.

Jan 1, 1978

By A. L. Mular

Optimization has been defined as the procedure of locating the best of something or the best way of doing something (Mular, 1971). Several texts (Himmelblau, 1972; Ray and Szekeley, 1973; Box and Draper, 1969; and Lee, Adams, and Gaines, 1968) on the subject are available. Such techniques have been placed in two categories, namely, off-line optimization and on-line optimization. For the former, an optimization model is employed; for the latter, a black box approach is involved. The essence of an optimization problem becomes obvious, when a response surface is considered. Suppose that a response (in this case, a criterion of improvement such as profit per day; grade of concentrate per day) denoted by Y, depends only on two variables, X1 and X2, which can be manipulated and controlled. The relationship between Y, X1 and X2 may be represented graphically as shown in Fig. 1. The diagram is called a response surface and its height, Y, is determined by X1 and X2. Points associated with equal responses constitute response contours. The shape is that of a hill, and optimization is the procedure of ascending the hill to reach the top (maximum). In practice, a response surface is subject to disturbances which distort its shape and shift its location from time to time, so that the exact location of a maximum is imprecise. Generally, constraints (restrictions of some sort) on responses and manipulable variables serve to define a region of permissible operation.

Jan 1, 1979

By Robert E. Ennis

The somewhat misnomered "continuous" face section is in most mines today still far from perfect continuity. Achieving uninterrupted flow of coal from the mining machine to the outside has been a long sought for goal. Clearly, the largest problem to be solved in continuous mining today is one of increasing the cutting time of the miner. Full machine utilization can never be achieved with the new high capacity miners, as long as their performance is tied to that of the shuttle car. Figure No. I illustrates the point at which shuttle car haulage distance determines unit productivity rather than the productive capacity of the miner. Continuous mining is never realized. A recent development has proven, however, that truly continuous mining and haulage is possible. The Bell & Zoller Coal Company working with the Research and Development Department of Hewitt-Robins Inc. developed and perfected a new mining system which offers advantages in terms of increased productivity at reduced mining costs and enhances the safety of personnel at the face. This new system involves the use of two pieces of equipment that form a unbroken link, at all times, between the mining machine and the mine belt haulage system. These pieces are a Mobile Bridge Conveyor, and an extensible panel conveyor. The following areas of discussion will be covered during the review of this development. I. The design and operating features of the new system. 2. Its application in underground mining 3. The performance of the system to date 4. Operation and maintenance cost considerations 5. Safety features of the system

Jan 1, 1965

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata

"Rock tunnels suffered severe damage from recent large earthquakes in Japan, despite the empirical knowledge that tunnels tolerate earthquakes better than surface structures. Seismic design for rock tunnels have therefore become a fascinating subject for many tunnel engineers. However, even basic behavior, including deformation mode and loading magnitude for hard-rock TBM tunnels and conventional ones during earthquake, has not been fully understood due to lack of actual seismic data; while EPB and slurry TBM tunnels take account of seismic design in Japan if needed. This study conducted a dynamic measurement in an actual road tunnel constructed in rock. The strongest aftershock of “the 2011 off the Pacific coast of Tohoku Earthquake” (Mw = 7.1) occurred during the measurement, providing precious data to examine deformation mode of the tunnel. Considering the acquired data, numerical analysis was also performed to calculate loading magnitude to cause fatal fracture of tunnel lining during earthquake.INTRODUCTIONLarge earthquakes can pose serious risks even for rock tunnels, as evidenced by large earthquakes in the past. In the large earthquake in Japan in 2004 (Mw = 6.6), some tunnels suffered severe damage including collapse of their permanent lining (Mashimo 2005), even though the tunnels were constructed in ordinary ground conditions except for fault, fracture zone, portal area, etc. To mitigate such risks, mechanical behavior of tunnel lining during earthquake should be clarified; however, even basic mechanical behavior including load-bearing capacity of the tunnel lining against earthquake is not fully understood.Numerous damage modes were actually observed due to various ground conditions (eg. Wang et al. 2001; Mashimo 2005). Among them, major tunnel damage caused by earthquakes can be grouped into three main modes as shown in Figure 1, excluding extremely unusual conditions such as a tunnel located on a stratum boundary where the stratum stiffness varies significantly. TYPE-I shows flexural failure or crack by bending moment at shoulders; TYPE-II indicates compression failure or flexural compression failure at crown; and TYPE-III illustrates compression failure at sidewall, mainly observed on tunnel that was constructed using steel ribs and lagging method. These damage modes, Type-I, II and III, are predominantly caused by shearing, horizontal compressing and vertical compressing deformations of the surrounding ground, respectively (Kusaka et al. 2011; Asakura et al. 2001)."

Jan 1, 2016

By T. D. Dreger

In the spring of 2009, Suncor Energy Inc. technical personnel saw an opportunity to improve planning and mining of overburden material in order to address aggressive construction goals and increased mining complexity. By tying together current and historical equipment performance, geological model information, and material observation in the field new operating elevations for the shovels were developed. At the same time, methodology of recording and reporting overburden movement through the Modular Mining DISPATCH system was changed. The result of this first stage of improvements was an increase in construction-grade material available at the face. The personnel involved realized that other opportunities were available to build on the initial successes and establish processes that would stand up to attrition and experience levels. A cross-functional technical team was assembled to identify ways of further improving workflows around overburden mining. Some of the opportunities realized include greater alignment between planning, reporting and operations as well as development of reporting tools that help steward Mine Operations to the plan. All of which have resulted in Suncor meeting or beating its forecast overburden targets. The cross-functional technical team continues to seek out new and better ways of doing business so Suncor can continue to deliver on its commitment of outstanding performance and results.

Jan 1, 2012

By L. S. Gertsch, M. Z. Abu Bakar

Linear cutting tests of a porous sandstone with a radial drag pick show that saturation of rock with water can increase the specific energy of fragmentation. This appears to be due, in this case, to a saturation-induced increase in the forces acting on the cutting tool without a concomitant increase of the fragmented volume. The mechanisms of this reaction are explored by examining various responses of the parameters controlled and induced during the linear cutting tests, such as cut spacing, cutter penetration, three-dimensional forces and muck production. A program of load-indentation testing is underway to evaluate the permeability threshold of this behavior. These findings are opposite from those made when the same rock is cut with a constant cross-section disc cutter reported elsewhere (Abu Bakar and Gertsch, 2011). Such results highlight the effects of different cutting tool designs, and indicate the need for a well-coordinated program of research to support effective excavator design and selection.

Jan 1, 2012