Search Documents

By Richard C. Corson

The objective of blending materials in a bedding pile is to reduce the variation in successive samples taken from the materials to be blended. In designing a bedding and reclaiming operation, several mechanisms are available to effect the reduction of variability, or increase in homogeneity, of the materials. These mechanisms can act before stacking, in the stacking process, in reclaiming and after reclaiming. In evaluating alternative methods of stacking and reclaiming, the potential user must judge each method on the basis of certain criteria; the capital cost of the equipment, the allowable absolute variability of the reclaimed product and the effectiveness of blending. Several stacking and reclaiming methods have been tested using a computer simulation. Based on the results of this program, factors were developed to describe the effectiveness of blending for chevron stacking of discrete materials and preblended materials, bucket wheel reclaiming and drum reclaiming. From these factors, the total effectiveness of a combined stacking and reclaiming system can be determined.

Jan 1, 1985

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By H. Colijn

The problem of the freezing of moist raw materials, such as concentrates, in railroad cars during winter shipment has been a continuing source of both economic and operational trouble to the industry and to the railroad companies. The difficulties center around the discharging of frozen cargoes into the plant materials handling system. Because of cargo freezing, appreciable delays in car-dumping schedules occur each winter and cause additional expense for demurrage charges and for slowdown of plant operations. In one plant during one winter, a car dumper rated at 40 cars per day could dump only 3 cars per day in bad weather. Delays became so serious one winter, that 500 cars held in the yard became so badly frozen, that they were sent to the southern part of the United States to thaw after they accumulated an average of two months demurrage charges. These delays in car unloading become critical if unit or integral train concept is applied to the movement of raw materials. Anticipated savings in transportation costs through better equipment utilization are largely based on rapid loading and unloading cycles of whole trainloads. If freezing problems cannot be adequately solved, unit train operations cannot be operated to achieve the potentially large reductions in transportation costs. The freezing problem may tend to become even greater in the years ahead, because the unit train concept will allow the trains to run faster and consequently the heat loss will be accelerated due to the larger heat transfer coefficient. A compensating factor, however, will be the shorter travel time. Further, the sources of raw materials being mined are located farther north than before and the ambient temperatures during transit are going to be lower.

Jan 1, 1976

By Hans Ruge

The El Soldado copper mineralization occurs as relatively high-grade irregular ore bodies with assay contacts and with frequent inclusions of barren rock. The sampling method must be timely for production grade control purposes, as well as accurate and inexpensive. Sampling techniques evolved from sampling dump cars at the haulage level to sampling scooptrams at the loading pockets. These were abandoned in favor of sampling production blast holes. Several sampling alternatives are discussed. These involve the selection of optimum volumes and sampling frequencies while taking into consideration geological parameters and statistical analyses of sampling data.

Jan 1, 1984

By G. R. Harrod

Effective mine operation demands that the right people have the right information at the right time. Caterpillar's Mining and Earthmoving Technology System (METS) meets this demand by providing "real-time" information transfer between the mine offices and machines equipped with the Caterpillar Computer Aided Earthmoving System (CAES). Transfers of mine plans from the mine planning software to CAES-equipped machines give operators access to current mine plans within minutes of their creation. Additionally, office personnel have access to a current digital terrain model (DTM) of the mine site as it is updated in "real-time" by CAES-equipped machines. METS provides mine personnel in operations, planning, and management the information they need when they need it.

Jan 1, 1998

By R. A. Matuszak

In recent years, a new concept in the control of electrically powered excavators has come into existence. The new type of control system has come to be known as "static" control. The use of the name "static" to describe this system is somewhat misleading since this term refers only to one of the many advantages of this very important advance in excavator control systems. In 1959, the first truly "static" control for Ward-Leonard equipped electric excavators was designed, developed and placed in service. The control system, originally intended only as a more modern electronic type of alternate to the tried and proven rotating amplifier control system then in use, has since proven to be much more.

Jan 1, 1964

By Dave G. Osborne

With the growing exportation of coal from North America to the Pacific Rim countries and Europe, has come an increasing awareness of the need to determine economically optimized amounts of incombustibles (ash and moisture contents) for the shipped product. Despite the fact that demand bas caused a steady improvement in selling price, particularly for thermal coals, growing production and transportation costs have compelled producers to keep a sharp eye open for ways and means of minimizing the latter since this probably represents the greatest single potential for making savings. Consequently the Coal Industry has become acutely aware of the economic ramifications of eliminating moisture in particular, thereby producing further saving in the cost of transportation of product from the mine to the consumer. There is, however, a lower limit to which dewatering or drying can be taken and this relates to dustiness which is a function of the characteristics of the coal and the methods used for handling and storage during trans-shipment. Overdrying can lead to serious dust losses and difficulties in handling particularly if the coal contains a large proportion of fines. The ways and means for achieving this "happy medium" of optimization in moisture removal are seemingly undergoing gradual modification largely assisted by the following factors. a) Improvement in effectiveness of coal dewatering and drying equipment. b) Improvement in operational availability and utilization of the equipment. c) The development of surfactants, polymer flocculants and other agents which in many cases can be almost tailor made to suit specific applications.

Jan 1, 1982

By Robert S. Lehto

Zinc concentrates received in La Oroya zinc refinery are marmatitic in nature, contain about 11% iron and traces of other metal values, Figure 1 shows the zinc circuit. The calcine from the roasted concentrates is leached in spent zinc electrolyte. Major part of the impurities is iron which has been oxidized to its trivalent form, This is the origin of the zinc leach residue for which the ZILERET process was developed and so named. The impure liquor from the leach is sent for purification and thence to electrolysis- zinc deposits on aluminum cathodes from which: it is stripped, melted and cast into slabs Typical assays of zinc calcine and leach residue are given in Table 1. Metal values contained in the leach residue, without counting any value of iron, amount to roughly $130 per short ton.

Jan 1, 1969

By Bo Arvidson

SALA MAGNETICS, INC. is now operating a 15 tph continuous high gradient magnetic separator, the SALA-HGMS® Mark III Carousel, as part of a complete mineral processing pilot plant installed at Sala's Cambridge headquarters. The Mark III can generate a maximum magnetic field of 18 kG making it possible to process even weakly magnetic, finely ground ores and ore tailings on a continuous basis at the performance level achieved in Sala's cyclic high gradient magnetic separators. Test results on iron ores, clay, and decoppering of molybdenum concentrate will be discussed. Bench scale tests have been performed on all of these materials using the SALA-HGMS® Model 10-15-20 Cyclic Magnetic Separator. A direct correlation may be made between cyclic and carousel results. Sala's Mark III Carousel high gradient magnetic separator is designed to permit scale-up to machines capable of processing two hundred (200) tons of ore per hour and more.

Jan 1, 1976

By R. L. Sundeen

Trackless vehicles, as the name implies, are machines not bound to rails, guide cables, or other direction controlling devices. They include, for the most part, vehicles which are wheel or crawler (track laying) mounted. Power sources may be self contained such as diesel or battery and can be defined as non-captive machines, while connected power sources such as compressed air or electric can be defined as captive machines. Trackless vehicles are used in all phases of underground excavation, loading, hauling and dumping. Early application found most machines with digging ability used to load those with payload hauling ability. As the versatility of trackless methods became more obvious the trackless vehicle has evolved to more productive machines such as the self loading haulers commonly referred to as Load-Haul-Dump equipment. Trackless vehicles find wide use in drifting and tunneling. Ability to negotiate adverse grades is especially noteworthy. Experience drawn from highly efficient room and pillar mining operations has lead to relatively wide application in drawpoint and cut and fill mining.

Jan 1, 1969

By G. H. Schnakenberg

In 1986, the US Bureau of Mines (USBM) embarked on a major research effort to develop technology that could substantially reduce worker exposure to face hazards by simply relocating the equipment operators to an area of relative safety. This reduced-exposure mining system (REMS) research effort enhances the USBM's ongoing health and safety efforts aimed at reducing and controlling dust and noise and reducing accidents through training and better mining practices. This paper reports on the progress made on the developing research and demonstrates the technologies required for the computer-assisted teleremote operation of continuous mining machines, haulage systems and roof bolting machines.

Jan 1, 1997

By Helmut Goehring

Surface mining has been used primarily where deposits of minerals were exposed or close to the surface. Surface mining can, therefore, be considered the oldest branch of mining. As the most accessible deposits became uneconomical because of the lack of suitable high capacity conveying systems, deep mining took its place. Only in the twentieth century was this trend reversed as high capacity production and conveying systems were developed. This rapid development was triggered by the steadily increasing demand for raw materials and fossil fuels, as well as by the ever increasing ratio between overburden and deposits.

Jan 1, 1982

By L. H. E. Weyher

Minerals beneficiation commonly requires initial crushing and grinding so that the mineral phase we seek to concentrate is adequately liberated to obtain a product of specified grade at optimum recovery. To some degree this also is true for coal preparation. In the comminution process we liberate not only the product but also the tailings phase. The true objective is, therefor, to eliminate from the comminution circuit whatever particulate matter has reached specified liberation, regardless of whether the particle is product or tailings material. Overgrinding either of the two phases ties up mill capacity and usually also burdens the downstream processing steps by increasing costs or decreasing recovery, or both. In view of this situation, one would expect concentration steps to be commonly incorporated into the cominution circuit. The reasons this is not done may vary, but probably include the desire to utilize large scale unit operations, e.g., large mills, in conjunction with very simple processes. Hydrocyclones have satisfied this desire but may not always be employed for the right reasons. Hydrocyclones are indeed simple. They also are rugged and forgiving. Unfortunately, these virtues are frequently misused. The direct results are inefficient classification and overgrinding. The indirect results are added costs through recovery losses, unnecessary recirculation, and so on,

Jan 1, 1985

By Robert Moore Lewis

Extensive exploration is being undertaken throughout the world in search for heavy minerals, particularly rutile and other titanium minerals. The federal government is sponsoring research involving rutile ores and recovery of stockpile-grade concentrates from domestic sources. Producers are being forced to turn to deposits with a heavy mineral content as low as 0.50% (essentially rutile and zircon). The North Carolina State University Minerals Research Laboratory investigated the possibilities of recovering heavy minerals from the amine tailings of the Texasgulf Inc.'s phosphate plant at Aurora, North Carolina. One laboratory beneficiation procedure using gravity, electrostatic and magnetic processes, resulted in the recovery of 78.7% of the heavy minerals in the amine tailings. Based on this percentage recovery and the present rate of phosphate mining, approximately 13,000 tons per year of heavy minerals (principally ilmenite and zircon) with a potential value of approximately $1,045,000 (1977) could be recovered. The economic potential for recovery of these heavy minerals appears to be favorable. A flotation procedure for up-grading the heavy minerals content in the amine tailings has been developed at the Laboratory, which could allow for concentration of heavy minerals and storing them in tailings area other than main tailings for future processing.

Jan 1, 1978

By Liming Yuan, A. C. Smith

Barometric pressure changes affect air density, leading to change in the mass of the gas in the gob. When the barometric pressure decreases, the volume of gas in the gob expands, while the volume of gas contracts when the barometric pressure increases, a process which causes the gob to “breathe” out and in. Although the concept of gob “breathing” is simple, its effect on spontaneous heating of coal in the gob area is not clear. In this study, computational fluid dynamic (CFD) simulations were conducted to model the spontaneous heating of coal in the longwall gob area under measured barometric pressure changes. A single longwall panel using a bleederless ventilation system was simulated. If there is no barometric pressure change, the intake airflow rate is equal to the return airflow rate. When the barometric pressure changes, these two airflow rates are no longer equal, and the difference between the two airflow rates represents the airflow rate the gob breathes in and out. The effect of inflow and outflow of gas on the potential spontaneous heating in the gob was investigated using the CFD model developed in our previous study. The effect of barometric pressure changes on the spontaneous heating was found to be dependent on the gob permeability and the coal oxidation rate. The effect of barometric pressure changes on oxygen concentrations in the gob was also examined.

Jan 1, 2010

By W. P. Diamond

The Bureau of Mines has been investigating several techniques, including the use of horizontal and vertical boreholes, to remove gas from coal in advance of mining. Horizontal boreholes drilled from underground workings as part of the mining cycle have been shown (Finfinger, 1980; Hagwood, 1983; Perry, 1978; Prosser, 1981; Thakur, 1980; VonSchonfeldt, 1982) to be very effective in providing short-term, immediate relief from high methane emissions. This technique has been widely accepted in the coal mining industry, but it does require close coordination to integrate the drilling and subsequent gas drainage and disposal into the projected mine development plan. Vertical boreholes can be placed several years in advance of mining to predrain gas from coalbeds over relatively large areas (Dunn, 1984; Elder, 1975; Lambert, 1980; Steidl, 1978; Stubbs, 1979). The vertical borehole technique has the additional advantage over horizontal boreholes of allowing work to be performed on the surface instead of in the more restrictive underground environment. However, except for the relatively large scale vertical borehole programs for both mine safety and commercial production in the Black Warrior Basin of Alabama (Dunn, 1984; Lambert, 1980; Stubbs, 1979), the technique has been underutilized. The primary reason for this seems to be a combination of the current economic climate in the coal industry, legal questions as to the ownership of coalbed gas, and potential roof damage from the stimulation treatments required to increase the characteristically low permeability of coalbeds to enhance gas production. The question of potential roof damage is the subject of this paper.

Jan 1, 1985

By Roshan B. Bhappu

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientific research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump leaching process and discusses salient features and parameters that may be helpful in improving such operations.

Jan 1, 1968

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986

By Paul D. Bybee

The Freeport Sulphur Company operates four sulphur mines in the coastal marsh area-03 South Louisiana. Employing the Frasch process of mining, approximately 13-million gallons of water per day is heated to a mining temperature of 325°F and is injected into the sulphur bearing formations of the four mines. A volume of cold waste water, roughly equal to the Input, is removed from the formations and presents a disposal problem. Two additional mines are currently being developed and will increase the disposal volume by an additional 5-million gallons per day. Although these properties are in a relatively small area, geographically speaking, as shown in Figure 1, they each represent a separate disposal problem with the treatment methods designed for the individual mine.

Jan 1, 1959

By W. D. Keller

Scan electron micrographs, SEM's, will be shown of representative refractory clays from Missouri deposits, with counterparts from other localities. The story is in the pictures, ("1000 words in each picture"), but clay types include the following. Plastic, semi-plastic, and semi-flint "fire clays" of Missouri have textures which appear to retain certain relic texture of ball clay. Flint clay is composed of tightly interlocking packets, sheaves, and books of kaolinite. Diaspore and boehmite mineral textures characterize those "clays". Surface-boulder diaspore shows very pronounced recrystallization and crystal enlargement from original, unexposed first-grade diaspore.

Jan 1, 1977