Search Documents

By M. J. DeMarco

Beginning in late 1985 and continuing through 1987, Bureau of Mines personnel investigated longwall chain pillar and entry design in two-and three-entry gate-road systems at a deep underground coal mine located in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau of Mines hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in roof falls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1988

By C. A. Rowland

Introduction Rod mills are horizontal, cylindrical, rotating, tumbling mills in which steel rods, that are usually about 6 in. shorter than the length of the grinding chamber, are used for grinding media. Fig. 33 shows a cutaway view of a rod mill. Rod mills were first used around 1910 because of their ability to grind in open circuit, consistently produce a uniformly sized prod¬uct, give greater continuous availability, and give lower maintenance costs. They have basically replaced roll crushers and coarse grinding ball mills in comminution flowsheets. The present 20-ft limit on rod length, based on rod manufacturing methods, and the pulp flow char¬acteristics, that influence mill capacity, have established the maximum rod mill sizes' of 15 x 21 Vs ft using 20-ft rods and drawing from 2,200 to 2,300 hp. Rod Mill Uses. The principal uses for rod mills are: preparing feed for ball or pebble mills, grinding gravel or aggregates to the size analysis required for making concrete sand, preparing coarse agitator feed for leaching operations, and for primary grinding circuits, particularly in industrial mineral applications. Wet grinding is the most frequently used grinding process for rod milling. There are a few special cases where dry rod milling is used. Preparing feed for ball or pebble mills is the most common use for rod mills. In ferrous and nonferrous ore concentrators, wet open-circuit grinding is used to prepare ball-mill feed. Figs. 34 thru 37 show the four basic grinding circuits used in these concentrators. In rod mill-ball mill grinding circuits, where the rod-mill discharge contains 25% or more of the grinding circuit product-size material, the rod-mill discharge can be fed to the ball- or pebble-mill classifier as shown in Fig. 34. This is the most frequently used rod mill-ball mill circuit in the nonferrous ore concentrators. In a few concentrators such as Anaconda's Weed concentrator,55 the rod mill discharges to one classification stage which makes the same or a slightly coarser particle-size cut as the classifiers used to close the ball- or pebble¬mill circuits, as shown in Fig. 35. In concentrators where rod mill-ball mill circuits are used to grind low grade magnetic iron ores such as Reserve Mining Co., Silver Bay, Minn.; Erie Mining Co., Hoyt Lakes, Minn.; Eveleth Taconite Co., Forbes, Minn.; US Steel, Mt. Iron, Minn. and Atlantic City, Wyo.; Inland Steel-Jackson County Iron Co., Black River Falls, Wis.; and The Cleveland-Cliffs Iron Co., Adams mine, Kirkland Lake, Ont., the rod mills discharge to rougher magnetic separators (cobbers), the concentrates from which are fed to a ball milling stage as shown in Fig. 36. The same basic circuit is also used with gravity concentra¬tion methods such as spirals (Hanna Mining Co., Groveland, Mich.), tables (St. Joe Minerals, Bonne Terre, Mo.), and jigs. When the rod-mill discharge contains less than 25% of the grind¬ing circuit product size, this indicates an ore that does not readily produce the fines needed to help carry the coarse feed into the ball charge. When this occurs, the fines in the rod-mill discharge are needed in the ball mill or pebble mill so the rod-mill discharge flows direct to the second-stage mills as shown in Fig. 37. Rod mills are used to make feed for open-circuit ball mills such as those used in wet grinding cement raw material (American Cement, Brennan Ave¬nue plant, Detroit, Mich., and Port Huron, Mich., plant, and at the South Dakota State Cement plant, Rapid City, S. Dak.). Grinding gravel or aggregates to the size analysis required for making concrete sand is used in areas where natural sand of the proper particle size gradation required to make concrete is not availa¬ble. Three-quarter inch crushed aggregate is ground to 4 mesh using center peripheral-discharge rod mills (Fig. 38) operating in open circuit. US Corps of Engineers specifications state that the sand product be 93-100% passing 4 mesh and contain no more than 3-7% passing 200 mesh. It may be necessary to classify the rod-mill discharge to remove any excess -200 mesh sand produced in the rod mill. Particu¬larly when processing aggregate with high abrasion indices, center peripheral-discharge rod mills are used instead of hammer mills, fine bowl crushers, and crushing rolls for the production of specification sand. If the -4 mesh size fraction of the rod-mill feed is removed

Jan 1, 1985

By R. E. Vivas

Goldcorp is one of the largest gold producers in the world with projects in South, Central and North America. Goldcorp?s flagship operation is Peñasquito, a world-class, poly-metallic deposit that started production in 2010 which is one of the largest mines in Mexico. Since the early stages of the project, Goldcorp has used the most advanced technologies available to maximize its value. However, the implementation of optimum mine plans has been challenging to put into practice. This is due to the fact that the mine operation involves more complexity than the plans usually reflect. This challenge is an industry wide issue that presents opportunities for improvement. This technical session discusses the mine planning methodologies and procedures used to connect long, medium and short term planning strategies in order to bridge the gap and produce optimum mine plans that can be practically implemented in the field.

Feb 23, 2014

By St. E. Deák

This paper focuses on maintenance of underground salt air curative quality using environmental friendly solutions. Possible ways to preserve its curative properties, in relation with the admissible salt air quality parameters, are analyzed. In situ investigations regarding microbiological impregnation in walls and the air inside the Romanian salt sanatorium were initiated. The results of a pilot project, which is in progress at Praid salt mine, are presented. After the end of the investigation at this site, investigations will continue in other Romanian salt mines, such as Slanic Prahova, Targu Ocna and Cacica.

Jan 1, 2006

By S. P. Mehrotra

In this review article, various approaches and mathematical models that have been used to simulate, design, and synthesize flotation circuits are examined. First, a brief review of flotation kinetics is presented which is followed by a discussion on simulation of flotation circuits. The existing literature on optimal design of flotation circuits has been divided into two broad categories. In the first category, a generalized integral approach is used wherein the optimal circuit design involves determination of both optimal interconnection of various flotation cells/ banks of cells in terms of structural parameters and optimal values of various operating parameters. In the second category, a conventional circuit configuration is assumed to be the best configuration; the optimal design here only means the optimization of operating parameters. The merits and demerits of these two approaches are discussed.

Jan 1, 1987

By Hans Hamrin, Bruce Kennedy

Once an ore body has been probed and outlined, and sufficient information has been collected to warrant further analysis, the important process of selecting the most appropriate method or methods for mining can begin. At this stage, the selection is preliminary only, serving as the basis for a project layout and feasibility study. Later, it may be found necessary to revise the details, but the basic principles for the ore extraction should remain a part of the final layout. With respect to the basic principles employed, relatively few mining methods are used today. For the purposes of this presentation, the principles are classified as follows: 1) For naturally supported stopes, the available methods are room-and-pillar mining and sublevel stoping. 2) For artificially supported stopes, the available methods are shrinkage stoping, cut-and-fill mining, square-set mining, and longwall mining. 3) For caving methods, the available techniques are sublevel caving and block caving. Due to the uniqueness of each ore deposit, the variations on each of these methods are nearly limitless. It is impossible to include even the major variations in this chapter; the goal of this chapter is to present the principles as a guide to the mining engineer in adapting the general methods to specific needs. The selection process described herein is intended to supply the techniques by which the candidate methods available for a given ore body can be reduced to one or two feasible approaches. The feasible approaches then can be evaluated in detail, and the particular modifications can be investigated. In describing costs and economic factors, all values herein are expressed in terms of 1978 US dollars.

Jan 1, 1982

By A. G. Yapo, T. W. Camm

"Mining plays a key role in the development of modern civilization as a source of essential raw materials and provider of essential fuels, producer of jobs and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer now than before as companies understand better their work environment and the importance of mining responsibly.A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production.An attempt to bring light and clarity to the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers, through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the all-in sustaining cost (AISC) and all-in cost (AIC).Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact, the high gross margin (sales minus cash costs) has been promoted in past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $61/g ($1,900/oz) in August 2011, gold producers were not reporting excessive profits in their cash flow/income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits.The disconnect led to a need for more accurate cost reporting in order to win back investor confidence and provide better understanding of gold mining economics. In 2012, the senior gold mining companies, including Gold Fields, Barrick Gold Corp. and Newmont Mining Corp., worked with the WGC to develop a new measure. This resulted in the June 2013 publication of the new framework AISC and AIC, which has been widely embraced by the sector since Jan. 1, 2014 (WGC, 2013).The adoption of the new cost template would have the dilemma of showing the real profitability of gold mine properties, which might alleviate taxes from governments and legislators, but it might also scare off investors toward more lucrative industries if not winning back their confidence."

Jan 9, 2017

By E. B. Fitch, D. A. Dahlstrom

Liquid-solids separation is common to practically all mineral and coal processing as the bulk of beneficiation plants employ water as the major processing vehicle. The growing usage of hydrometallurgy has increased the importance of liquid-solid separation as acidic and basic solutions result in greater amounts of colloidal solids, with their consequent greater difficulty of separation, the economic need for chemical recovery to minimize this operating cost, and the usual necessity of employing more costly construction materials. The three processing steps covered in this section have significant capital costs. Drying, particularly, has an important operating cost because of the obvious need for energy to evaporate the water or solvent. Several common factors influence all three liquid-solid separation steps. Particle Size and Size Distribution. In general, finer particles have slower settling and filtration rates. The specific surface area is increased, which means a lower solids concentration in the thickener underflow and discharged filter cake as well as a grater moisture content to be evaporated in the drying step. Therefore, overgrinding or excessive attrition should be avoided. Consideration should be given to optimum particle size consistent with entire plant operation performance and recovery. Solids Concentration. Increased feed solids concentration will generally minimize required equipment size and costs in all three liquid-solid separation steps. Most thickeners are designed on the basis of unit area required, expressed as square feet per short ton of dry solids per day (square meters per metric ton per day) which will usually decrease with increased feed solids concentration. Filtration rates also increase as the required flow through the capillaries of the filter cake decreases. Dryer capacity increases and less energy per ton of final product is required to evaporate the associated moisture. Particle Shape and Surface Characteristics. Generally, optimum shape is a spherical particle of zero porosity. As either of these factors degrade away from the desired state, difficulty increases. This is particularly true in drying, where porosity can decrease drying rate significantly if the moisture must first reach the particle surface by diffusion

Jan 1, 1985

By James E. Kolesar

An essential prerequisite to expanding the application of longwall mining techniques in the United States is the development of a better understanding of the mechanics of rock mass deformation near the mined seam, in the inter- burden and at the surface. The results of studies of this type will provide a basis for the development of empirical and/or numerical modeling techniques to predict the rock mass response to mining both near and far from the mined seam. This will lead to improved gate and panel design, resulting in maximum recovery, increased productivity, as well as provide a mechanism for assessing likely surface effects induced by long- wall mining. Presented here is the instrument plan to be used at Kitt Mine No. 1 in the study of rock mass response to two adjacent longwall panels.

Jan 1, 1982

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By M. Modis

According to previously established theoretical analysis and under certain conditions, a critical sampling grid can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results, while based on this limit the ideal process of reproducing the original phenomenon is theoretically defined. The objective of this paper is the application of the above theory to the Klidi lignite deposit in Florina, Greece, where Public Power Corporation (Greece) has conducted a sampling campaign to estimate the deposit thickness and its heating value. Data acquired for these two variables were analysed in the space domain in order to derive their respective correlation functions. The structural analysis of the deposit generated two covariance models, one for the thickness and one for the heating value, from which the critical sampling grid was identified. The conclusion drawn is that in some parts of the deposit the sampling grid is denser than required. Finally, an optimal sampling grid is proposed in order to gain the maximum information at the lowest cost.

Jan 1, 2006

By J. E. Murphy, Y. Topkaya, R. E. Johnson, B. R. Palmer, D. K. Dysinger, R. B. Bhappu, A. E. Clark

The U.S. Bureau of Mines utilized a central composite experimental design to investigate leaching kinetics of pure chalcopyrite in the sulfuric acid-oxygen system. The six factors studied were oxygen pressures of 150, 300 and 450 PSI, leach temperatures of 35O, 65O, and 95O C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0 and 1.5, leach times of 8, 16 and 24 hours, initial acid strengths of 0.6, 1.2 and 1.8 g H,SO,/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. Chemical analysis and oxygen consumption measurements indicatedthat leaching occurs through three consecutive reactions. Temperature was the primary determinant of leach rate and solution acidity was the primary determinant of oxygen consumption, sulfur oxidation, and activation energy.

Jan 1, 1993

By D. S. Choi

The paper contains a subsidence measurement taken over a room and pillar panel of a mine located in northern West Virginia. A total of 72 monuments were used to determine a three dimensional view of mine subsidence. In addition, the results of measurements were used to compute ground strains with the use of a numerical model.

Jan 1, 1982

By William J. Shampine

The Floridan aquifer, which underlies all of Florida, yields water with a hardness of less than 180 pmts per million (ppm) in the northwestern part and throughout much of the center of the Slate. In most of the rest of the Stale, the aquifer yields water having a hardness greater than 180 ppm and as much is 1,900 ppm. Hardness of ground water is caused by dissolved salts from the geologic formations through which the water passes or by direct pollution. Sometimes pollution may indirectly increase the hardness of ground water by increasing the acid content and thus increasing the solution of calcium and magnesium salts. Water from deep zones of the aquifer lend to he harder than water from more shallow zones. Only the hardness of water from the upper part of the aquifer is shown.

Jan 1, 1966

By H. Ankara

Determining the identicalness levels of the same model trucks working in open pit mine transportation system by means of statistical analysis methods is very significant in terms of availability analysis. In this study, the identicalness levels of two trucks picked randomly from the 170-short-tonne truck fleet working in open pit coal mine over one-year period were examined through a non-parametric test, Mann-Whitney U test for two samples. Time to failures (TTFs) and Time to Repairs (TTRs) of the trucks were analyzed with this test technique and then whether they were identical or not was determined. In order to determine whether the trucks identified to be identical at the end of this test displayed the same mining performances within the same open pit transportation system, the availability analysis of the identical trucks was carried out. As a result of the availability analysis, it was observed that the trucks had availability values that were very close to each other. It was also determined that Mann-Whitney U test could be employed together with availability analysis. Finally, it was observed that Mann-Whitney U test for two samples could yield rapid results in the performance analysis of complex systems like open pit mines.

Jan 1, 2010

By S. F. Diehl

Suites of monomineralic sulfide and carbonate minerals, as well as mine-waste composite samples, were analyzed using chemical and microanalytical techniques to understand behavior and bioavailability of mine waste elements such as Cu, Fe, Pb, or Zn. Petrographic, scanning electron microscopy (SEM), and laser-ablation inductively-coupled mass spectrometry (LA-ICP-MS) studies of mineralogical residence sites of trace elements are important because trace elements affect the chemical and physical behavior of minerals. Leachate solutions show that chalcopyrite, bornite, azurite, malachite, and galena are host to the trace elements Ag, Al, As, Cd, Co, Cr, Mn, Ni, Pb, and Zn. SEM studies reveal whether these trace elements occur within mineral inclusions or are substituted within lattice structures. SEM analysis reveals mineral phases not identified by X-ray diffraction (XRD), such as inclusions of sphalerite and cobaltite(?) within chalcopyrite.

Jan 1, 2010

By J. A. Chermak

Piles of sulfide-bearing overburden, ore, and tailings have the potential to generate acid drainage (AD) when exposed to an oxidizing environment. Laboratory column experiments were conducted using acid-generating overburden material with an added surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results showed that the limestone and/or lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxy-hydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on this study, hardpan layers can be created as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic overburden or tailings material. Unlike traditional capping methods (for example, clay and high density polyethylene (HDPE) covers), chemical caps are self-healing.

Jan 1, 1996

By S. Veeramasuneni

The recent nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble-salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. These results also indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. In this regard, the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. Results from this study indicate that, while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions.

Jan 1, 1999

By Robert W. Bruhn

The prediction of damage to a structure that is to be undermined is generally a two step process. First, the expected ground movements (the displacements, slopes, curvatures, and strains) are estimated using available (often empirical) predictive methods or survey data from a site of comparable geology, topography, and mining geometry. Second, the prospects for damage to the structure are assessed by comparing the expected ground movements to tolerable limits, some of which appear in the technical literature as damage criteria. The inverse problem of relating observed building damage to causative ground movements involves essentially the same elements. In either case, the usefulness of published damage criteria to subsidence problems may be limited in all but the most elementary cases. This paper considers several cases where structural behavior and site specific details had to be taken into account in assessing the relationship between damage and ground movements.

Jan 1, 1986

By George M. Meisel

This paper is devoted to a discussion of the factors governing design of concentrators for large grinding circuits. Emphasis is placed on the manner in which use of ever larger grinding mills has affected the size of grinding bays, service cranes, gear reducers and electric motors, and the selection of ancillary equipment for cushioning of the starting load of large mills. Information is presented on the effect of using large grinding mills on the capital and operating costs of concentrators, e. g. : (Fig. 1) ? Benefits in lower cost of mills, drives and materials handling equipment, plant space, power, grinding media, operating labor and maintenance, and in ease of instrumentation and automation. ? Penalties in distribution of materials from the grinding mills to multiple lines of equipment which have not been developed to commensurately large sizes, and higher cost of ancillary equipment.

Jan 1, 1968