Search Documents

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low-, a medium-, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0 percent ash, as follows: From low-volatile anthracite, 0.7 percent; from medium-volatile coal, 1.0 percent; and from high-volatile coal, 2.3 percent. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0 percent or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a conventional dense-media washing plant.

Jan 1, 1968

By F. F. Peng, Y. Xia

In modeling of hindered-settling bed separators, the published separation mechanisms are based on differences of particle density and size distributions, without the details of complexity of particles-liquid interactions. A fluid dynamic model for the separator is developed using Euler-Lagrange approach of Computational Fluid Dynamics (CFD). Fluid motion is obtained from solving the movement of liquid governing equations. The damping effect on flow pat-terns caused by the movement of particles resulted in liquid-particle coupling is included in the model. Effects of particle size, and particle density compositions, feed rate, feed water flow rate, upward fluidizing water flow rate, etc., are simulated in the 2-D separation model. Flow pattern effects on the separation of fine particles in the separators with center downward-flow and side cross-flow feed systems are investigated.

Jan 1, 2004

By Leonard H. Hoyle

The American Society of Association Executives is a professional society composed of nearly 10,000 individuals who serve as salaried executives on the staffs of more than 6,500 associations. Represented is the full range of international, national, regional, state and local associations...including trade associations, professional societies, philanthropic organizations and others. The dramatic growth of ASAE during the past 15 years is a manifestation of the growth of the association movement during the past two decades. This is not to imply that associations are a new phenomenon, because they have existed for thousands of years. Ancient civilizations show evidence of groups formed for mutual protection and advancement. In the transition from ancient to medieval time, trade associations and guilds came to serve an important function for the craftsmen and merchants they represented, encouraging the growth of new industries, improved processes and education.

Jan 1, 1981

By N. Edmonson

Introduction An examination of statistics for the world phosphate fertilizer industry since 1980 reveals that there is an increasing tendency for fertilizer-manufacturing activity to concentrate in the areas of phosphate-rock mining. The economic justification for this resource-oriented strategy is clear. The choice between shipping phosphate rock, a comparatively low-value product, and shipping a more valuable finished fertilizer product will always, as long as cost considerations control the decision, be resolved in favor of the latter. The historical existence of substantial phosphate fertilizer-manufacturing capacity, which is oriented toward fertilizer-consuming activities and dependent on imported phosphate rock, shows that narrow cost considerations have not always determined the industry's location. One is entitled to ask what conditions have changed to precipitate the observed relocations, and how permanent are these changes. These questions are the subject of this investigation. Recent trends in world phosphate trade Since 1980, the changing pattern of world trade in phosphate materials reflects an increased interest in manufacturing phosphate fertilizer in rock-producing areas. This is shown by the decline in the total tonnage of phosphate rock being traded worldwide compared to world consumption of phosphate fertilizers (Fig. 1). This relative decline has continued since 1984, which is a longer period of time than could be explained by temporary cyclical market factors. Other evidence corroborates this conclusion. The world's phosphate-rock production is relatively concentrated geographically. In 1992, the top ten producing countries accounted for 92% of world production. Figure 2 shows that the share of world fertilizer production in the top ten rock producers has increased. Yet, further evidence of the direction of trade changes can be had by looking at the pattern of the world's sulfur trade. The first step in the manufacture of any of the widely used phosphate fertilizer products is the acidulation of phosphate rock with sulfuric acid. In most instances, phosphate fertilizer producers have found it economical to produce their own sulfuric acid by burning elemental sulfur, and such operations account for over 60% of all sulfur consumption in the world. 1 Therefore, a concentration of phosphate fertilizer production in rock-producing countries should produce a similar concentration of sulfur imports in the same countries. Figure 3 suggests that there has been a tendency since 1989 for sulfur exports to go increasingly to the rockproducing countries. World phosphate-location strategy is not limited to the alternatives of shipping rock and shipping finished fertilizers. A third alternative consists of producing phosphoric acid, the principal phosphate fertilizer intermediate, at the rock deposit, and then exporting it to market-oriented ammonium phosphate plants. This arrangement offers the importing country the advantages of shipping a more concentrated product while retaining the economic multiplier benefits of a domestic high-analysis fertilizer industry. India, and several other countries, imports merchant-grade phosphoric acid to use as input for the domestic value-added fertilizer industries. For various reasons, the trade in phosphoric acid has never quite lived up to the promise suggested by the foregoing discussion. Figure 4 shows no growth in this trade in the last ten years, either in absolute terms or in relation to the world's consumption of phosphoric acid. Most of the decline in the trade in phosphorous in rock form has been replaced with trade in finished fertilizers. The trade in superphosphoric acid was a growth activity in the late 1970s with the growth in US exports to the USSR, and this trade survived the Carter-era embargoes of US-Soviet trade. However, no additional sizable markets for superphosphoric acid developed, and other suppliers sought out the Soviet market. The problem with superphosphoric acid is that the cost of its incremental concentration is as great as the savings from shipping the more concentrated product. The Soviet market was a special case. The political breakup of the Soviet Union disrupted the superphosphoric acid trade after 1991 and led to a shutdown of the US export capacity.

Jan 1, 1996

By N. J. Themelis, W. H. Dresher

Research is probably the least understood and the most underrated or overrated, depending on the circumstances, function of the corporate enterprise. Some companies become engaged in research because they consider it to be vital to their very existence, others in order to develop new business, and some with no clearer objective than to keep up with the competition. Whole new industries have resulted from research activities, such as the Xerox copier, the transistor, the computer, and have affected considerably our way of life. Companies have prospered or perished by pursuing the successes or failures of their research organizations. However. despite the tremendous effect that research has had on our modern civilization and the billions which are spent on it annually, we have not as yet been able to develop many hard and fast rules as to how to conduct it effectively and to a successful end.1 This section discusses the role of research in the United States and in the mineral industry and describes a few of the criteria and guidelines which have been developed to assist in increasing the probability for success in industrial research. Broadly speaking, the purpose of industrial research is to make a significant contribution to the long-term viability and the profitability of the sponsoring company. The sum total of technological developments has been a principal factor in establishing the United States as a world leader and the controlling element in the nation's balance of trade with foreign powers. The international aspect of most mineral commodities is a significant factor in the business decision-making of most domestic mining companies and should be an important factor in the operation of research and development (R & D) programs in these companies. The National Science Board has reported that in recent yean other nations have been gaining on the United States over practically the entire range of science. 2,3 On the positive side, the NSB reported a strong position for the US in the results derived from its investment in R & D. If the United States is to maintain a favorable trade balance, it must create new know-how through technological innovation in order to create new industrial products, processes, and services for which there is a global demand. As expressed by Chauncey Starr, president of the Electric Power Research Institute, "Unlike resources found in nature, technology is a man-made resource whose abundance can be continuously increased, and whose importance in determining the world's future is also increasing."' In recent years, the greatly in- creased pressures for environmental quality and energy conservation have enhanced further the role of technical innovation in insuring the future survival of the domestic industry. Technology is the challenge of American industry, and it is a challenge which the mineral industry must also accept, for processed minerals are the very raw materials and energy on which all of industry is based, it is technology which makes a mineral deposit into an ore reserve. The Natural of Industrial R D Research is usually thought of as being either basic or applied. Basic or fundamental research is the quest for knowledge and need not have any practical objective. Applied research is the search for a solution to a particular problem and therefore has a specific objective beyond the acquisition of new knowledge. Development is the next stage to the applied research experimentation and it generally consists of larger-scale tests to establish the technical and economic feasibility of the new process or product and to provide design information for its industrial implementation. The terms research and development are usually interconnected for the good reason that in many cases it is difficult to define where one ends and the other begins. For instance, in many cases, thermodynamic, kinetic, corrosion, and other research studies, which are needed to provide design data for an industrial plant, may prod in parallel with the pilot plant activities preparatory for this plant in order to conserve time. Often the final stages of a development project may involve the trial production of a new product for markeing tests or the trial operation of a new process on a "semi-industrial" scale pilot plant. Such operations may be termed "demonstrations"; hence, more

Jan 1, 1985

By C. A. Roberts

What are the benefits and limitations of financial analysis software as a decision making tool in the mining industry? Traditionally, the assumptions and simplifications imposed by complex and uncertain information have been viewed as the main obstacle to reaching an optimum decision. Recently, however, phenomena such as corporate culture and power structure have received increasing attention as significant influences on organizational decision making processes. Studies of these phenomena have suggested an alternative way of understanding decision making processes and an alternative view of the role played by computer analysis in such processes. This paper presents these two views of decision making, and examines what each implies about the role of financial analysis software as a decision making tool in the mining industry.

Jan 1, 1992

By Roger N. Miller

Talc mining in Vermont has in recent years undergone a progressive change in mining methods and in mining equipment. Underground mines have been phased out except in special circum- stances, and continuous mining machines (CMM?s) have replaced conventional drill/blast mining systems. Talc mining in Vermont began in the late 1800?s, and has continued without interruption to date. Beneficiation (flotation) has been applied since the early 1930?s, and has provided special products for toiletries and other markets. At the present time, there are two active companies that have evolved from the cumulative absorption of nearly ten smaller operations.

Jan 1, 1984

By W. J. Miles

Oil based drilling fluids utilize a number of industrial mineral products to accomplish oil and gas drilling in several environments where water based drilling fluids are less effective or inappropriate. These industrial minerals include: organically modified bentonite, organically modified lignite, barite, hematite, mica, calcium chloride and other salts. A variety of organic products are also utilized in oil based drilling fluid formulations. Oil based drilling fluids are preferred in several drilling situations because: they can be used to drill through water sensitive formations; they produce holes that are very close to the drill bit gauge; they exhibit high temperature stability; they are more environmentally acceptable; they minimize producing formation damage; they provide faster drilling rates when used with new polycrystalline diamond drill bits; they minimize pipe sticking and lost rig time.

Jan 1, 1986

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By C. P. Mangelsdorf, Richard A. Allwes

At the request of the U.S. Department of Labor, Mine Safety and Health Administration (MSHA), the U.S. Bureau of Mines evaluated the suitability of using tri-sets for protecting mine personnel in roof-fall prone areas. A steel-set arch provided by MSHA served as a basis for evaluating the performance of the tri- set. All tests and analyses were conducted according to the arch canopy test and design procedures developed by the Bureau. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of their experimental behavior. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri -sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that tri-sets may be considered for protection against roof falls, provided that the arch canopy design procedure is utilized for each application and that the principles underlying the design procedure are understood.

Jan 1, 1992

By X. Xie

The dissolution behavior of palladium powder in thiourea solutions has been studied. The variables studied included temperature, stirring speed, and concentrations of thiourea, acid and ferric ion. Palladium was found to be soluble in thiourea solutions in the presence of an oxidant such as ferric ion. The dissolution of palladium in thiourea solutions was found to be chemical reaction controlled with an apparent activation energy of about 2S.3 kJ/mol.

Jan 1, 1995

By Anders Sellgren, K. Hansson, A. Jedborn

In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore. from a system's point of view, slurry transportation would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alternative examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasibiliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. 1. The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then temporarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe- line, and personnel are needed. In a first phase (Fig. 2). a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1990

By Ellis Brien, O&apos

The fine coal fraction of a coal stream is that fraction which contains particles essentially in the -28 mesh size range. This fraction will normally first appear, in a coal preparation process, as a result of classification to segregate raw coal into various size components for beneficiation. More specifically, it could appear in desliming screen underfiow, classifying cyclone overflow, and in other process circuit components. It's recognized that the top size of this fraction has been determined more by secondary reasons, such as desliming screen area for the heavy medium cyclone circuit, the dewatering equipment for the fine clean coal, or even the stability of the refuse thickener circuit. Benefits, both economic and environmental, gained by beneficiating the fine coal fraction of a raw coal stream are increasing in number, until today, fine coal beneficiation is a necessity in most coal operations requiring any degree of preparation. This is due to some of the following reasons: • In the past it was frequently more economical to discard -28 mesh raw coal sizes than to recover the coal values from them. Today, mining costs have escalated to the point where all coal values leaving the mine should report to the finished product if possible. • Today's mining methods are producing run-of-mine coals containing higher percentages of -28 mesh sizes. This heavily weighs the economic balance in favor of beneficiating this fraction. As much as 25% of the run-of-mine coal from some mines is in the fine coal fraction. Beneficiation is recommended so that clean coal contained in the fraction can be recovered to reduce the loss of coal values. • Existing and pending environmental regulations mandate that solid fuels now consumed in power station boilers contain almost no pyritic sulfur. This form of sulfur appears in raw coal in the fine coal fraction, but can be removed by coal beneficiation. Environmental considerations dictate that every year, more of the fine coal produced for steam generating purposes in the US be beneficiated. To deliberately discard any portion of the fine coal can only add to this cost, not only in the sense that fewer tons will be recovered but, more importantly, additional tonnage will be diverted to the most capital- and labor-intensive section of the entire preparation plant-the fine refuse dewatering section. It is apparent to preparation engineers that dewatering and ultimate disposal of the fine refuse derived from this beneficiation step is certainly the most difficult technical problem presented in the entire plant design. Therefore, any beneficiation procedure which increases the fine coal recovery, or in any manner decreases the tonnage of fine refuse to be dewatered, is going to be cost effective. Since the -28 mesh fraction contains both coal and refuse particles in their finest particle sizes and thus presents the greatest degree of liberation, one would immediately infer that the highest degree of beneficiation would be achieved. This is not the case-the opposite is more likely true. Conventional coal cleaning devices based on specific gravity (such as

Jan 8, 1980

By G. H. Friedrich

The distribution of mercury in soils, rocks, and ore was studied in three areas of the Pachuca-Real del Monte District: (1) An area north of the town of Pachuca where ore veins have been found at or near the surface. The mercury content of soil samples taken near the vein zones is far above the background value. The highest value was 1900 ppb (parts per billion) mercury in a soil sample above Veta Vizcaina; the background is about 50 ppb Hg. (2) In the area north of the town of Real del Monte where only a few of the veins are known to crop-out. Regardless of exposure, soils collected over veins show anomalous mercury values ranging from 250 ppb to 1900 ppb. (3) In an area south of the town of Real del Monte. Here, although vein outcrops are lacking, mineralization is known at a depth of about 120 m. All soil samples taken at 50 m. intervals along an east-west traverse contain anomalous amounts of mercury, with peaks corresponding with the known location of the veins.

Jan 1, 1965

By K. Hansson, A. Jedborn

Background In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore, from a system's point of view, slurry transporta¬tion would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alterna¬tive examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasi¬biliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. l . The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then tempo¬rarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situ¬ations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe¬line, and personnel are needed. In a first phase (Fig. 2), a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1989

By Faruk Oksuz, Dave Schiemann, Miguel Sanchez, Patrick Jensen

"The McCook Main Tunnel connects Chicago’s Tunnel and Reservoir Plan (TARP) Mainstream Tunnel to the McCook Reservoir. The tunnel system consists of a 10 m (33 ft) finished diameter and 490-m (1,600-ft) long hard-rock tunnel constructed from a 27.5-m (90-ft) diameter and 92 m (300 ft) deep main gate shaft. The gate shaft houses six high-head 4.4 x 9 m (14.5 x 29.5 ft) wheel gates installed in the bifurcated and steel-lined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir. Construction of the McCook Main Tunnel in live flow conditions was a challenging task for the McCook Main Tunnel Project participants, the project owner U.S. Army Corps of Engineers (USACE), local sponsor Metropolitan Water Reclamation District (MWRD) of Greater Chicago, designer Black & Veatch and contractor Kiewit Infrastructure Co. (Kiewit). Once completed in two stages in 2017 and 2029, the McCook Reservoir will hold 38 billion L (10 billion gal) of combined sewer overflows (CSO) and flood waters from the city of Chicago and 36 surrounding communities in Cook County, IL The construction of the tunnel system was divided into two contracts. The first contract for the gate and construction access shaft was completed in August 2011. The second contract included tunnel excavation and concrete and steel lining that was completed in September 2014; installation of gates and hydraulic cylinders that was completed in June 2017; and the last major construction activity was the removal of a temporary concrete plug (bulkhead) and lining that tunnel section to bring the overall tunnel and gates system online before Dec. 31, 2017.This article focuses on the installation, testing and commissioning of the high head wheel gates. Live tunnel connection details to TARP Mainstream Tunnel were addressed in a previous paper submitted at the World Tunneling Conference in 2016."

Mar 1, 2019

By B. Andersen

An accurate knowledge of Interactions among mineral particles and between such particles and dissolved and precipitated species Is Important in developing efficient separation processes. In this investigation interactions in Florida phosphatic clay waste, that are relevant to dispersion and selective reagent adsorption, the two main prerequisites for selective flocculation, were studied. Initial studies with artificial slimes, consisting of pure clay and phosphate minerals, showed dispersion of artificial slimes to be relatively easy. The problems that were encountered during selective flocculation of the artificial slime were due to unselective polyacryllc acid adsorption on clay, which was caused by the presence of multivalent calcium ions on the exchangeable cation positions on the clay surfaces. This problem could be solved by exchanging calcium for sodium, which reduces the interaction between the polymer and the clay surface. This procedure, however, was not successful for mineral mixtures. Natural slimes were found to be much more difficult to disperse. This was attributed to the presence of cementing materials such as humic substances and Ai and Fe (hydr)oxide precipitates. Selective removal of these cementing materials resulted in good dispersion and partial separation. Further increase in separation of natural slime is likely determined by the presence of calcium on the clay surfaces, as was found for the artificial mixtures.

Jan 1, 1992

By James P. Ludwig

While we are all aware of the need for reclamation of mine sites, few managers and engineers seem to be aware that good reclamation begins with the earliest plans for mining and processing of ores. Far too often the attitude that reclamation is an add-on to worry about at the end of the mining process dominates the thinking of mine engineers and management, A common result is that the reclamationist can be faced with mining and waste disposal designs that are nearly impossible to deal with effectively from an ecological perspective. Everyone of us has been victimized by the down time and maintainence cost that resulted from the purchase of an outwardly attractive, but poorly designed piece of equipment. When confronted by design defects in equipment, a distraught owner can always trade it in, call a consumer advocate, or follow up one of the "lemon laws" at either the federal or state level. A poorly designed mine for reclamation purposes usually cannot be treated either with ease or cost effectiveness. Good reclamation can be effectively prevented by the designs used when the mine was planned. The purpose of this paper is to share some of the experiences our firm has had with reclamation projects at mines in the Upper Midwest as these were influenced or controlled by mine design decisions. My aim is to sensitize mine planners and managers to planning processes they should consider, and hopefully use, early in the mining process to assure successful reclamation during and after mining. Many of the examples I will cite are from experience gained at the recently closed Jackson County Iron Company taconite operation at Black River Falls, Wisconsin. I am particularly grateful to Mr. Vern Metzger, mine manager at JCIC, for his unflagging support of good reclamation practices, employee training programs (which have included reclamation techniques), and his forebearance to put up with our group of ecologists. I realize that this was a time when there were significant internal and external pressures to cut all costs including reclamation efforts. The collaboration has been successful as you will soon see.

Jan 1, 1984

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By J. M. Mutmansky, B. Kolonja

A PC-based simulation model using the software packages SIMAN and CINEMA was developed to simulate and animate truck-shovel operations. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. Statistical analyses were performed, and appropriate theoretical distributions were fitted for various time events in the truck-shovel cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an optimal dispatching strategy to produce an equilibrium between the quality and quantity of production.

Jan 1, 1995