Search Documents

By John P. Fillion

This paper will present an overview of conveyor haulage systems. Technical and economic feasibility will be examined as conveyor haulage is applied to large western surface coal mines. Theoretical analysis and actual cases will be presented from NERCO Coal Corp. experiences in bringing this application to their Western mines.

Jan 1, 1989

By H. L. Ehrlich

Processes involving biological solubilization of metal values from ores, or removal of mineral constituents that interfere with metal value recovery from ores by abiological means, published mostly in the last 10 years, are reviewed. Many of them, though promising, have yet to be tested on a pilot scale or applied industrially.

Jan 1, 1987

By I. Andras

The paper deals with the application of artificial intelligence methods in assessing the effectiveness of longwall shield support. A fuzzy sets based method is used to derive response surfaces/curves representing the dependence between basic parameters of the shield, as the initial setting pressure and the stiffness on the response metric, i.e. the convergence and load increase during a working cycle.

Jan 1, 2008

By S. P. Singh

To understand the intricate nature of blast damage and counter the associated problems, small-scale blasting experiments were performed on hydrostone blocks. Tests were then conducted during a drifting operation in a quartzite quarry. Blast damage was assessed by different techniques. On the basis of the experimental results, the effects of the energy partitioning characteristics of explosives on the damage were identified.

Jan 1, 1993

By John T. Gormley, Pressley L. Campbell, Harry L. Crouse

INTRODUCTION This paper summarizes an investigation conducted to determine the relationship, if any, between reported occurrences of abnormal levels of carbon dioxide (C02) gas and the construction of a 2.44meter diameter main sewer tunnel under South Eighty-Fourth Street, West Allis, Milwaukee, Wisconsin. Specific objectives of the study were to determine: (1) the sources of C02, (2) the significance of each C02 source, (3) how C02 could move to areas where it was reported to occur in abnormal concentrations, and (4) what actions could be implemented to eliminate elevated C02 levels associated with the tunneling operation. To accomplish study objectives, expertise from several scientific and engineering disciplines was required including chemistry, geochemistry, microbiology, hydraulics, and hydrology. Pertinent documents were reviewed and field data pertaining to each aspect of the study were collected as required and examined to evaluate existing conditions. Background On or about February 1, 1971, gas with a composition different from normal atmospheric air was reported to enter basements and wells of residences in the vicinity of South Eighty-Fourth Street, West Allis, Wisconsin. Examination of the gas composition revealed that it possessed an elevated concentration of C02 and a depleted concentration of oxygen (02). Public health officials who investigated the appearance of the objectionable gas concluded within reasonable certainty that the elevated C02 concentrations were associated with the tunnel construction under Eighty-Fourth Street.

Jan 1, 1979

By P. C. Thakur

In gassy coal mines, some methane drainage is essential for mine safety, but the ratio of total methane drained to total methane produced by the mine can vary from 10 to 70 percent. The volume of methane not captured is diluted by ventilation air and vented to the atmosphere. Since captured methane can be processed and sold, it makes sense to maximize methane drainage from coal mines. This paper describes ventilation and methane drainage schemes to achieve these goals.

Jan 1, 2003

By Rashi Tiwari, George Danko, Jeremy Knowles

A control technique is described for enhancing the efficiency of materials handling and other mining operations. The concept involves human-operator and robotics control interactions to assist in mining operations. Many mining tasks require a human operator to coordinate the motion of several machine links by simultaneously manipulating multiple joysticks or other control devices. The new control architecture allows for automatic coordination of multiple machine joints. The machine movement may follow a computer-optimized, learned coordination pattern, while the operator still retains the master control of the overall trajectory and velocity parameters. Examples are described for a surface mining front shovel.

Jan 1, 2005

By J. R. Cooper

Since man began beneficiating ores, a limited number of factors influenced the type of treatment. The ore itself has always been a factor. The first form of concentration was probably hand sorting, and the grade of concentrate and recovery had to be considered from the start. The cost of labor as a factor in mill design did not attain importance until the period following World War I. Power was one of the cheapest commodities available, and consequently power consumption was ignored. That no longer holds true. The present work does nothing to simplify the work of the metallurgist, or designer. On the contrary it adds another element to the design considerations. And while this report concentrates on power consumption, the mill designer must take the other factors into account as well. This study is based on a compilation of data supplied by a number of Western United States copper operations, as well as information from equipment manufacturers. Although its conclusiones apply to other minerals and geographic areas, the information is more precise, when applied to similar ores. The discussion has been divided into sections covering crushing, grinding, and flotation as these are the principal power consuming functions.

Jan 1, 1977

The concept of "classification is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters which affect fines removal are identified and discussed, and a quantitative index for circuit fines removal effectiveness is defined. This approach lends new interpretation to certain observed phenomena, and suggests useful guidelines for circuit design and operation.

Jan 1, 1985

By Bernard Amadei, Michael J. Robison

The purpose of this paper is to present the results of 102 mu1tiaxial tests conducted on cubical specimens of Indiana limestone using the mu1tiaxial apparatus available at the University of Colorado at Boulder. These tests include (1) uni-axia1 compression and tension, (2) bi-axial and tri-axial compression, (3) biaxial compression- tension and (4) tri-axial compression-compression- tension. The applicabi1ity of existing failure criteria to predict the strength of the tested materia1 is discussed.

Jan 1, 1986

By K. Verghese, H. M. Lee, R. P. Gardner, K. Boateng

Results of work on the development of a phenomenological model for the continuous flotation process wing short-lived radioactive tracer techniques for determining model parameters is reported. A model that incorporates a flotation first-order rate constant and a residence time distribution based on the cross-flow finite-stage (CFFS) model has been derived and investigated. The short-lived radioactive tracer techniques and the nonlinear search methods necessary to extract the model parameters have been developed. The conditions under which all the model parameters can be extracted from a single radiotracer experiment are detailed and illustrated. A micro- computer-based unique data logging system has been designed, assembled, and implemented for collecting the necessary transient radiotracer data. Results are reported for a continuous laboratory flotation process for the two systems, mica ore and coal.

Jan 1, 1987

By W. Robert Power

Dimension stone includes a wide variety of natural materials that are put to an equally wide variety of uses. It is possible to classify dimension stone according to the end use to which the stone is put or according to the lithology of the stone. Both schemes are used by the United States Bureau of Mines in the annual Minerals Yearbook. The 1969 Yearbook lists 15 specific uses and has additional miscellaneous catagories. The same Yearbook lists five specific rock types or lithologies, and also includes a miscellaneous category. In a short presentation it would hardly be possible to list and define all these categories, much less discuss the evaluation of deposits with regard to all possible combinations. Besides, I am only slightly familiar with some of the uses and their requirements. I have therefore chosen to limit my remarks to some special problems in evaluating dimension stone that is to be cut and finished to specific sizes, tolerances, and finishes for use in buildings and some monuments. This use class is called cut stone in the Minerals Yearbook. In terms of dollar value it is the largest single use category. In 1969 the dollar value of cut stone was $29,122,000 which is more than twice the value of the next largest category. For those of you who are interested in other use applications of dimension stone I suggest that you start with recent articles by Bowles (1960), Currier (1960), and Barton (1968).

Jan 1, 1972

By R. W. Hutson

One of the fundamental precepts of experimentation is the isolation of a single variable to quantify its individual effect. Unfortunately, the variability of natural rock joints has frustrated such isolation. This variability and the high cost of securing a large member of natural joints has lead to increasing experimental dependence on stage shearing, artificial tension fractures and/or model materials. The new apparatus described herein allows for the first time replication of real joints with field scale asperities. It employs a diamond band-saw blade with computer controlled feed table to cut joints with high precision. The feed system is capable of placement to tolerances similar to those of a high quality computer plotter. The accompanying software allows the table to cut any desired joint shape (repeating or non-repeating) within certain, over-all size limitations. Resulting joint surface dimensions and roughness as well as shear resistance indicates that the joint surfaces are reproduced with a precision similar to that possible for the control of other experimental variables such as normal and shear forces.

Jan 1, 1986

Dravo Corporation was founded in 1891 and has long been recognized as a major domestic engineering and construction firm headquartered in Pittsburgh. In 1977, Dravo had revenue of $852.2 million with international business activities contributing $248 million; quite a different picture than envisioned at the turn of the century. Engineering and construction activities still dominate Dravo's most recent history and will do so for the immediate future. However, fluctuations in capital spending by large industrial sectors of our economy during the late sixties were affecting Dravo's planning for continued growth along its traditional lines of business. Diversification was a possible solution to smooth out the upward trend in corporate earnings. One large result of these continuing efforts was the formation of Dravo Lime Company, a vertically integrated, proprietary chemical supplier for the air pollution control market. Briefly retracing the seventies, the passage of the Federal "Clean Air Act" in 1970 supplied the impetus for Dravo Lime Company. This law promulgated limits on the emissions of sulfur dioxide (SO2) from large stationary sources that would affect local air quality. The major industry that felt the brunt of this regulation was the electric utility industry, especially those generating electricity with coal-fired boilers. The law hastened the development of a new industry, flue gas desulfurization (FGD), and is composed of three major segments: (1) the electric utility, (2) the FGD equipment suppliers (the scrubbing modules), and (3) the scrubbing chemical suppliers. Dravo's experience suggested the equipment end of the business but market analysis indicated that our long range corporate goals could be better attained by investigating the chemical processes involved in the removal of the SO, gas. The result being Dravo Lime Company. This paper will briefly describe the Thiosorbic lime scrubbing process and review our innovative mine and calcining facility.

Jan 1, 1978

By Z. Man, X. Zhu, Y. Xian, Y. Tao

"Fine coal separation has been always concerned. The froth flotation is not efficient in desulfurization because of the low rate of sulfide liberation from raw coal, the natural hydrophobicity caused by sulfur concentration on the surface of sulfide, and the presence of large amounts of middling feed. An efficient centrifugal gravity separator was employed to separate for Shandong –0.5mm high sulphur coal, the partition curve of centrifugal separator was obtained with conclusion that the Ecart probable error value of the separator is 0.095, the imperfection I value is 0.128. Finally, comparing with the coal flotation using progressive release method, the result shows that the effect of the desulfurization with centrifugal gravity force field based on density difference between coal and minerals are much better than that of the floatation which operates based on the difference in surface properties. It provides a efficient technical way for fine coal separation. INTRODUCTION Coal plays the most important role in the energy consumption in China. Although natural gas, wind energy, nuclear power has made great progress in recent years, but the share of coal in the final energy consumption accounts for 70-80%, which is determined by energy storage of China. Under the requirement of environmental protection, the clean utilization of coal resources becomes more and more important, and the need has already been identified. Coal washing and processing plays an important role in the process of high-efficiency and clean utilization of coal. For the separation of fine coal, flotation is a traditional method for effective separation and has been used in large scale industrial applications in coal preparation plant. However, for the separation of difficult-to float coal, especially fine oxidized coal and low–rank coal with hydrophilic surface, flotation is usually inefficient [1-3]. Although many pretreatment methods have been adopted, including grinding, microwave pretreatment, new flotation reagents, the problem of efficient separation has not been completely resolved [4-6]. Thus, an enhanced gravity separation method using particle density difference rather than hydrophobic difference was proposed for the separation of fine coal. Many research results have proved that this is a practical and effective method of sorting. R.Q. Honaker used Falcon C10 concentrator, Knelson centrifugal separator and spiral separator to clean the fine coal with size of 600*210 µm and 210*37µm, the effects of different operating parameters on the separation index was discussed. The results show that the separation density of Falcon can reach 1.6, and the Ep value can reach 0.1-0.15. This paper revealed that for the separation of fine coal with high sulfur content or fine grained content. Falcon has high separation efficiency with low cost. Separation results present in another paper showed that the desulfurization efficiency of inorganic sulfur was better than that of flotation [7-8]."

Jan 1, 2017

By I. Melik-Gaykazov, N. N. Melnikov, V. A. Fokin, S. P. Reshetnyak

Kola Mining Institute has been carrying out investigations of the possibility to steepen the walls of the Kovdor open pit with the design depth of 600 m. Steeping (up to 60°) wall angles is done by double height (24 and 30 m) benches with vertical slopes. One of the safety factors of mining with such walls is choosing the width of the safety berms preventing against rock falling from the slopes into the pit working area. The test on rock falling from 24 m benches has shown that vertical slopes are not more dangerous compared to the inclined(60-75°) ones.

Jan 1, 2003

By M. Cambridge

During the latter part of the twentieth century exploitation of mineral resources, and gold mining in particular, experienced a resurgence in Europe, with major mining houses and many junior companies involved in exploration and subsequent mine development. Gold projects in particular were actively encouraged and exploration programmes and permitting studies initiated in more than 15 countries, both within the European Union (EU) and the former eastern bloc. During the initial period, governments in many countries provided active support. Following a series of negative environmental mining incidents in the latter part of the century public opinion, often ill-informed, led to political pressure to withdraw governmental assistance. This in turn resulted in the revocation of exploration licenses, and ultimately to the failure to develop a number of potentially world-class mines within the region. Despite these setbacks, gold production in Europe continues, and is probably higher now than 20 years ago. The mining industry is currently coming to terms with both changing attitudes of governments, and the increase in scope and prescriptive nature of legislation. Recent experiences, particularly in Greece and Turkey, exemplify the problems faced by the industry in the region, which are causing major mining companies to reconsider future activities in Europe. The paper presents an overview of European gold mining and its environmental performance in the context of international practice, new legislation, and public perception of mining generally. The rationale of governments in withdrawing support for the industry is questioned, and the feasibility of achieving sustainability where there is no level playing field globally is reviewed. The question is posed to governments, regulators and mining companies alike as to whether there is a future, not only for gold mining, but for the minerals industry in general, within the EU.

Jan 1, 2003

By G. R. Green

The centre of the mining operations of the International Nickel Company, Ontario Division is Sudbury, a city of 160,000 population located 240 miles northwest of Toronto (Fig. 1). Within thirty miles of this city and located around the rim of the geological formation known as the Sudbury Basin are the ten underground mines and one open pit operated by the Company (Fig. 2). There are also four developing mines, three in the Sudbury area and one at Shebandowan, near the city of Thunder Bay, Ontario and approximately 150 miles north east of Duluth, Minnesota. In 1971 the mines produced 22,800,000 tons, 20,600,000 tons from underground and the balance from open pits. Also located in the Sudbury District are facilities to extract and refine the metals contained in the ore. There is a nickel refinery located at Port Colborne on Lake Erie. An additional nickel refinery is under construction near Sudbury. Fifteen elements are recovered from the Sudbury ores, nickel, copper, iron, sulphur, gold, silver, cobalt, tellurium and the six platinum group metals, platinum, palladium, iridium, rhodium, ruthenium and osmium. In 1966 a major expansion program was undertaken to meet increasing market requirements. Coinciding as it did with a severe

Jan 1, 1972

By D. C. Torre

Since the early 1960s, there have been efforts to develop and produce reliable continuous haulage systems capable of taking the full output of a continuous miner and transporting it, in one continuous flow, from the face to the tipple. The majority of the successful continuous haulage systems were placed in operation in the early 1970s. These were all of the bridge conveyor type. They usually consisted of bridges and mobile bridge carriers (MBC) attached at the inby end to the continuous miner and at the outby end to the panel conveyor itself. These successful bridge conveyor continuous haulage systems are either of the belted or chain type. The most successful belt type continuous haulage systems are those manufactured and marketed by the Long-Airdox Co. Until early 1977, Jeffrey Mining Machinery Division manufactured and marketed the most successful chain conveyor type haulage sys¬tems. In 1977, Long-Airdox reentered the market with a chain-type system to complement its belted system. The original bridge-type continuous haulage system was introduced to the coal mining industry in the early 1960s by the old Long Co., a predecessor to the current Long-Airdox Co. These original units were of the chain conveyor type. In the early 1970s, there were also developments in continuous haulage, employing different material handling media. These in¬cluded the Serpentix, a flexible type belt, introduced by the Joy Manufacturing Co. There was also a serious attempt to introduce hydraulic-type continuous haulage by Consolidation Coal Co. and Conoco Research. Despite some startling successes, particularly with the bridge-type haulage systems, the general and widespread application of continuous haulage has eluded the mining industry. Some of the problems are related to underground conditions; others to people, both management and labor. One of the greatest obstacles to universal success continues to be the difficulty of accepting the philosophy as well as the machinery of continuous haulage. Nevertheless, efforts continue to spread the success of commercial and viable systems in the industry. There is also effort to improve on these systems, and on methods for their successful use. In addition, efforts continue, with private and public support, to develop new types of continuous haulage equipment and systems. Bridge Type System Developments Because they have already been successful in some US and overseas mines, new developments in bridge-type systems will first be touched on. The Long-Airdox Co. has continued to improve both its belted and chain continuous haulage system. In the belted system, the company recently introduced a new design that will be mainly applicable in higher coals and in noncoal mining applications, as shown in the accompanying figure. This new system is equipped with 305-mm-diam (12-in.-diam) pulleys in the bridges and mobile bridge carriers, in place of the 150-mm-diam (6 in.-diam) pulleys in the standard system. The modification is designed primarily to improve belt life and keep belt problems to a minimum. An operator, the Clinchfield Coal Co., a Division of Pittston Coal, developed the detaching of the bridge-type continuous haulage system from the miner by placing a mobile bridge carrier at the head of the string. However, Long-Airdox and Jeffrey have now made this an option to their at¬tached-type system. In the US, there are many chain type haulage systems detached from the miner with an extra MBC at the head. There are two such belted systems

Jan 7, 1982

By Allan E. Koski

Michigan is the second largest iron ore producing state in the United States. The Empire Mine, celebrating its 30th anniversary in 1994, is the largest iron ore mine in the state. The Empire Iron Mining Partnership is an iron ore mining, concentrating and pelletizing facility managed by The Cleveland-Cliffs Iron Co., a subsidiary of Cleveland-Cliffs Inc. The Empire Mine is located near Palmer, MI on the Marquette Iron Range in Michigan's Upper Peninsula. The partnership includes Inland Steel Co., LTV Steel Co., Wheeling-Pittsburgh Steel Corp. and Cleveland-Cliffs. Mine construction began in 1960. The first pellets were produced in late 1963. Successive expansions in 1967, 1974 and 1979 resulted in Empire reaching a present annual capacity of 8.1 Mt (8 million long tons) of pellets. In late 1993, a milestone was reached with the production of Empire's 152-Mt (150-millionth long ton) of iron ore pellets.

Jan 1, 1994