Search Documents

By Lynn B. Hales, John A. Herbst, Thomas L. Gabardi

A system for a continuous determination of the charge volume of grinding media in ball mills and SAG mills has been developed. The system, comprised of a unique measurement device and a model based Kalman filter algorithm, determines grinding media level within a mill and calculates media and liner wear rates. The signal from an instrumented washer mounted on the exterior of the mill shell is used to provide the measurement that, along with mill power and on-line models for media mechanics, result in estimates of mill parameters that can be used in media addition control strategies. Data are presented for a 12.5 x 15 ft. ball mill.

Jan 1, 1990

By J. E. Chilton

Methanometers with catalytic heat- of-combustion sensors used in coal mines today will read low for flammable gases when oxygen (0,) concentrations are low or when methane (CH,) concentrations are greater than 10%. Thus, these methanometers may not be reliable during operations such as fire fighting or recovery of sealed mines. The U.S. Bureau of Mines developed a total flammable gas detector (TFGD) to measure CH, at concentrations up to 100% and to measure flammable gases in low 0, concentrations. This paper describes the operation and construction of the TFGD and discusses measurements of flammable mine gases obtained from a mine in western Pennsylvania.

Jan 1, 1992

By C. F. Meyer

The recirculation of mine air in an underground colliery, has always been regarded as a hazardous practice in South African collieries. The Mines and Works Act and Regulations states that fresh air, flowing Into an underground section, must flow out directly into the return airways after being utilized once in the section. One of the largest producing underground collieries in South Africa, Initiated a project on controlled recirculation with the permission of the South African Government Mining Engineer. The project involves the recirculation of 65 m3/s of air inside a ventilation district which serves a total of six production areas. The aim of the project was to increase the airflow to the sections without altering the existing ventilation system. Tracer gas studies were carried out to determine the actual distribution of the recirculated air to the individual areas. The results showed that an effective 54,18 m3/s of the recirculated 65 m3/s reaches the sections. This gives an air utilization figure of 83,4 per cent. Dust surveys were also carried out as part of the project to determine the effect of the recirculation of the return air on airborne dust levels. The results showed that the dust levels remained constant in the main intake and return airways and that no hazardous situation was being created. The project proved to be successful and showed that controlled recirculation can be executed and used as a solution for the supply of air to sections without endangering any lives.

Jan 1, 1993

By D. Zaharaki

In the present experimental study the geochemical stability of inorganic polymers was studied by immersing them in various solutions (distilled water, seawater and 0.5N HCl) for a period of 7 months. Inorganic polymers were synthesised by mixing ferronickel slag with kaolinite, potassium hydroxide and sodium silicate solution. The cement like paste was heated at 80 °C for 48 hours and left for curing at room temperature. Their structural integrity was assessed by compressive strength testing after subjection to freeze-thaw cycles as well as high temperature heating. XRD studies were carried out in order to identify new formed phases and provide useful information regarding the progress of the mechanisms involved.

Jan 1, 2008

By Jan M. Mutmansky, David R. Kalasky

Computer simulation continues to be one of the most successful analytical applications of computers in the mining and mineral processing industries throughout the world. Through simulation, managers and engineers can explore the impact of new technologies, equipment designs, plans and operating strategies to improve their operations. It is not uncommon for a single simulation application to provide a quick payback of analysis expenses (within weeks or months) yielding long-term financial and operational dividends. The paper will present a summary of the types of software systems that are available for use on PCs and other computer systems. Support software for curve fitting, statistical analysis, and optimization of simulation models will also be presented. Methods of leveraging simulation efforts through networking and coupling of software systems will be discussed. Finally, the trends in simulation in the mineral industries will be analyzed. Areas of strength and weakness of simulation will be discussed along with the usefulness of commercial general-purpose and custom-writ- ten simulation packages. The future possibilities for simulation in the mineral industries will be outlined and predictions on trends for the future will be presented.

Jan 1, 1996

By G. T. Lineberry, B. R. Yama

Artificial intelligence research has produced several tools for commercial application. Some of the techniques that are widely used today include neural networks, fuzzy logic and expert systems. Artificial neural networks (ANNs) are excellent predictive, pattern recognition and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process-control applications. Modeling of spatial data, ore-reserve estimation, tunnel design, long wall-stability prediction and geologic roof classification are additional applications in which neural networks have been applied successfully. In this study, a standard back propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, the performance of the network is measured on an independent validation set. Results indicate a mean error of less than 1 % between the actual and predicted values. A neural network model was developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values for given coordinates. The neural network not only performed satisfactorily, but in some cases performed even better than the kriging model.

Jan 1, 2000

By L. G. Austin

Using an instrumented laboratory high-pressure grinding rolls mill, the grinding force, gap dimension, mass flow rate and net mill power were measured for six coals and a crystalline quartz. A technique was developed to estimate the compressive stress-strain curves for compression of the materials in the mill plus the effects of elastic decompression. To reconcile the mill power and grinding pressure results, it was necessary to allow for the energy recovery on decompression. No clear correlation was obtained between the form of the stress-strain curves or the variation of specific mill power factor with the Hardgrove grindability index (HGI), although coals with the lowest and highest HGIs (i.e., 44 and 106) gave results significantly different from the other coals. Feeds below 140 mesh (105 µm) flowed more rapidly than coarser feeds and would not build up high grinding pressures. This indicated shearing and fluidlike properties rather than compression as a locked bed.

Jan 1, 1998

By Salama

In the conventional approach, the separator feed incremental masses are assumed to be concentrated at the midpoints of the density or size intervals and subjected to a model partition function. The resulting separation predictions would change if the locations of the incremental masses were changed. As a result. the predicted results depend on the choice of locations where the feed incremental masses are concentrated in the density or size intervals. A technique that utilizes the cumulative-mass-distribution of the circuit feed and the derivative of the partition (separation) function relative to density or size variables is proposed. The proposed technique eliminates the dependency of the predictions on choice of where the feed incremental masses are concentrated within the density or size intervals. Since the proposed technique is based on the cumulative masses at the upper limits of the density or size intervals, the technique produces a single prediction whereas the existing techniques produce predictions that depend on where the incremental masses are concentrated. In fact, it has been demonstrated that the existing conventional technique, in which the incremental masses are concentrated at the midpoints of the density or size intervals, is a first-order approximation of the technique proposed.

Jan 1, 2002

By Schebek, J. Warsen

"Data and information from sustainable development (SD) reports can be seen as a promising and easily accessible source for an Life Cycle Assessment (LCA), i.e. for generic Life Cycle Inventory (LCI) data in particular. The reliability and comparability of LCA results crucially depends on the quality of LCI data, that is defined by specific normative requirements. In parallel the GRI (Global Reporting Initiative) provides a set of guidance documents for enhancing the quality, rigor, and utility of SD reporting with specific reporting principles that address similar issues on a company level comparable to LCI data quality requirements on the process level. In order to assess the general suitability of the fundamental reporting principles for LCI data quality purposes selected reports from mining and minerals (M&M) sector are assessed within a detailed analysis."

Jan 1, 2005

By Jon C. Volkwein

The U. S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography at the Pittsburgh Research Center. These gas results were analyzed for explosibility. Personal exposure to carbon monoxide was also monitored. The highest methane level observed was 9.55 pct. The Inert gas levels, (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were non-explosive. The maximum personal time weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining. INTRODUCTION The auger highwall mining method is an effective method to recover coal from a reserve when removal of the overburden by surface mining equipment becomes uneconomical. In this method of mining, a horizontal auger enters the coal seam from the surface mine bench under the highwall and the coal is drilled in a series of parallel holes. Historically, coal mined from the surface is relatively shallow, and over time, methane associated with the coal has dissipated through the surface. In most circumstances, little methane has been found associated with auger mining. However, mining technology has enabled surface mining of deeper reserves of coal. Furthermore, environmental constraints have forced the highwall extraction method to be used to remove coal under wetlands, further increasing the chances of encountering methane. Recently incidents of methane explosions at a few auger mining operations have resulted in injuries and increased testing for methane at the collars of auger holes. The fuel source of the reported explosions was not necessarily limited to methane, but may also have involved coal dust. The Mine Safety and Health Administration (MSHA) met with the Bureau to discuss what technology might be available to enable the safe resumption of mining. The discussion included the difficulty of ventilating through the solid shafts of the augers, that steel bits probably created the ignition source, and that perhaps inerting the holes with low oxygen and high carbon dioxide concentrations from the machine's diesel exhaust was a potential solution. Considering the ventilation aspects of the problem, it was not clear If ventilation could be reliably established. If some degree of ventilation to the front of the mining head is achieved, it may combine with methane to bring the hole atmosphere from a rich, nonexplosive mixture to an explosive mixture. Furthermore, it may not prevent a dust explosion in such a mining configuration. Lack of access through the shafts of auger type mining machines further limits the ability to add water or air to cool bits to prevent an ignition source from developing. Either of these approaches would also be expensive. The process of mining coal In an inert atmosphere has been considered in the past, but to our knowledge, never implemented (Department of Interior, 1970). Clearly, implementation in underground mining would be more complicated. On a mine bench open to the atmosphere, however, adding inert gas to the mining head could provide a quick, feasible method to prevent explosions at auger highwall mining operations. Also the problem of how to move the inert gas to the cutting head of the machine had to be considered. Preventing explosions on auger mining machines using inert gas requires three primary considerations: first is the source of inert gas; second, placing the inert gas at the cutter head; and third, monitoring the hole atmosphere. Any gas source having an effective inert gas concentration of 34 volume pct or greater will prevent methane from Igniting (Zabetakis, 1965). Sources of inert gas considered for this application included liquid nitrogen, modified shipboard inert gas generators (for hydrocarbon shipping and transfer), jet turbine engine (Paczkowski, et. al., 1982), the auger's diesel engine and a gasoline engine. Operation cost, purchase cost and availability limited our testing to the diesel and gasoline engines. This work tested each engine, separately and combined. To ensure effectiveness, both company and enforcement personnel need to know how to monitor the condition of the inerted hole. Measurements at depth inside the hole are possible by remote sampling through rigid tubing, but this method is Impractical for routine monitoring. Continuous monitoring of the exhaust gas stream is an alternative. The U. S. Bureau of Mines evaluated an inert gas system at an auger mining operation at a surface mine near Owensboro, KY. Coal was mined from the Number 9 Coalbed in Henderson Co. KY. Tests were conducted in January and March of 1992.

Jan 1, 1993

By Gordon R. Haworth

Conditions affecting minerals investments are continuing to change at an increasing rate, and in this paper we will attempt to predict the course of mine financing in the future. We will first review the situation historically and then examine the problems and constraints that are now making the financing task more difficult. Suggested solutions are discussed, and a new method of financing a group of mining projects is hypothesized.

Jan 1, 1977

By Lawrence J. Connelly

During the last decade, use of freeze conditioning agents (FCA) to ease unloading and handling of both run-of-mine and washed coal during periods of cold weather has become an accepted practice by the coal industry. This paper reviews some of the mechanical means of easing the handling of coal during periods of cold weather, as well as their use in conjunction with FCA's. Factors required to promote a successful cold weather handling program are also covered. Mechanisms by which FCA's function and the influence of various substrate characteristics on the ultimate response to freeze conditioning agent performance are discussed. A modified approach to freeze conditioning is presented.

Jan 1, 1986

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By H. W. Renner

The paper industry is an $80 billion/year business that is the largest consumer of industrial minerals. Paper industry generally refers to paper and paperboard products, including pulp mills. Grades and uses of paper and paperboard are very diverse, including such things as napkins, paper plates, corrugated boxes, magazines, newsprint, currency, and copier paper. Only about 40% of paper utilizes industrial minerals as fillers or coating materials. Minerals are used for both functional and economic reasons. Most often, minerals such as kaolin clay and calcium carbonate are used to improve print quality, brightness and opacity of paper. The minerals can be added as fillers into the paper in the wet end of the papermaking system, or can be applied as part of a coating to the paper. Coated papers are the highest quality paper, being used for magazines, advertising brochures and annual reports. Common uses for filled uncoated paper are books, copier paper, envelopes and many of the Sunday newspaper advertising inserts.

Jan 1, 1993

Steady state simulation has become a highly effective approach to the optimization of existing mineral processing plants and the design of new facilities. Accurate phenomenological models imbedded in user-friendly software packages make this advanced technology available to the mineral processing engineer. The new version 2.0 of the USIM PAC software package contains many improved features, and a new Windows 3 graphics interface. The main features include Objective-Driven Simulation, new fields of application, improved data processing algorithms and improvements in the design and optimization capabilities.

Jan 1, 1992

By J. K. Ahlness

The US Bureau of Mines investigated technologies for determining the integrity of in situ leach mining wells. A self-contained trailer-mounted well integrity testing system (WITS) was designed and built to enable rapid testing of well casings for leaks as required by environmental regulations. The WITS utilizes two inflatable packers to seal off the entire casing length or any portion thereof. Water pressure is built between the packers to the desired test pressure, and the presence or absence of casing leaks is determined by monitoring the pressure drop between the packers. A winch and steel cable are used to run the packers in and out of the well. The WITS underwent an industry field test at the Irigaray in situ uranium leaching mine near Buffalo, WY. A total of 37 wells with an average depth of 69 m (225 ft) were tested at an average rate of four wells per eight-hour shift with a two-person operating crew. This represents a 75% time savings and an 83% labor savings compared to the rigid-pipe method previously used at the mine, with which a three-person crew tested an average of one well per shift.

Jan 1, 1988

By K. Komnitsas

This paper presents the main environmental assessment techniques and indicators that can be used a) for the establishment of a sustainable development framework and b) for the evaluation of the environmental performance within the mining sector. Reference is made to techniques as environmental risk and impact assessment, life cycle assessment, cost benefit analysis and best practical environmental option assessment that can be used as tools to assess environmental impacts of processes, activities and products in the mining sector. In addition, the issue of environmental indicators, covering operational, management and environmental areas, that provide valuable information regarding both the environmental performance of a mining company and its efforts to influence this performance towards sustainability is discussed.

Jan 1, 2003

By J. M. Kruger, P. Berendsen, A. Martinez

High-resolution ground-penetrating radar (GPR) was used to image the near-surface extent of two exposed Late Cretaceous kimberlites intruded into lower Permian limestone and dolomite host rocks in northeast Kansas. Six parallel GPR profiles identify the margin of the Randolph 1 kimberlite by the up-bending and termination of limestone reflectors. Five radially intersecting GPR profiles identify the elliptical margin of the Randolph 2 kimberlite by the termination of dolomite reflectors near or below the kimberlite's mushroom shaped cap. These results suggest GPR may augment magnetic methods for the delineation of kimberlites or other forceful intrusions in a layered host rock where thick, conductive soil or shale is not present at the surface.

Jan 1, 1998

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By Adam Feiler, John Ralston

Optical reflectometry was used to study the attachment and subsequent detachment of silica particles (diameter 25 nm) from the surface of titanium dioxide wafers under well-defined hydro- dynamic conditions. Atomic force microscopy was used to measure the interaction between silica spheres (diameter 7 pm) and titanium dioxide wafers under the same solution conditions. In addition to repulsive electrical double layer forces, adsorbed polyphosphates provide a short-ranged steric layer that reduces the lateral interaction between the surfaces. The use of these two complementary techniques has given valuable insight into the process responsible for fine particle detachment and has particular application to surface cleaning.

Jan 1, 2003