Search Documents

By Robin D. Rogers

Room temperature ionic liquids (RTIL) can replace certain traditional organic solvents in liquid/liquid extraction of metal ions from aqueous systems. The very low vapor pressure and non-flammable nature of RTIL warrant consideration of these neoteric solvents for new processing technologies which will reduce pollution, Increase safety, and lower costs. Metal ion separations in RTIL, however, will typically require the use of an extractant and research is needed to identify suitable selective extractants which have appreciable solubility in the RTIL and low solubility In the aqueous phase. Choice of extractant should also take into account the toxicity, expense, and disposal of the ligand.

Jan 1, 1999

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By Zhang Jianliang, Xu, Zuo, Runsheng, Haibin, Kexin, Jiao

Full oxygen blast furnace iron-making is one of the new technologies, which is most likely to realize large-scale application. In this paper, based on the technology of full oxygen blast furnace, the reduction behavior of pellets is studied systematically by using the analytic method of non-isothermal dynamics on the different atmosphere(CO,H2) and the dynamics model of gas-solid reduction reaction is constructed, which lay the foundation of reduction model establishment of full oxygen blast furnace burden. The result shows that the time of pellets which began to react is delayed with the increase of the content of H2. When the temperature is between 650 'C and 1050 'C, the content of H2 in the reduction atmosphere is larger, and the rate of the reduction pellets is larger. The reduction rate changes at 780 'C, and a certain amount of H2 in the reducing atmosphere will significantly improve the reduction reaction when the temperature is above 780 'C. Non-isothermal reduction behavior is controlled by interfacial chemical reaction and internal diffusion under high reduction potential. H2 ratio in reducing atmosphere increased from 0% to 100%. The reduction reaction of the apparent activation energy decreased from 49.03kJ-mor1 to 33.74kJ·mor1.

Jan 1, 2013

By Stephen C. Britten

An in-situ amperometric slag sensor for measuring the concentration of easily dissociable oxides in slags at temperatures between 1200-1600°C is being developed. The sensor provides the same information as potentiometric sensors while also providing data on the concentration of the transition metal species and the diffision kinetics within the slag. The electrochemical technique utilized in the sensor is similar to methods utilized in aqueous voltammetry.

Jan 1, 1998

By Rollie E. Dutton, David A. Stubbs

"A sensor has been developed and tested that is capable of emitting and receiving ultrasonic energy at temperatures exceeding 900°C and pressures above 150 MPa. The sensor works with standard ultrasonic pulser-receivers and has demonstrated the capability of measuring workpiece deformation during hot isostatic pressing (HIP). Details of the sensor design, performance, and coupling of the ultrasound to the workpiece are described. Ultrasonic data acquired by the sensor, in situ, during HIP runs and at elevated temperatures in air are presented.INTRODUCTIONHigh temperature structural components, such as structural castings for jet engines, nickel-base superalloy turbine blades, and ceramic and metal matrix composites made from powders are often densified by hot isostatic pressing (HIP). For powder consolidification, the HIP process involves sealing the powder (and reinforcing fibers for composites) within an evacuated ""Can"" made of a material that softens at high temperatures. A hydrostatic pressure is then applied by pressurizing the inside of the HIP vessel with argon gas (up to 140 MPa). The hydrostatic pressure densities the powder through the elimination of the porosity between the powder particles.This paper presents details of the development and preliminary testing of an ultrasonic displacement sensor that can be used to monitor materials processing, in situ, at temperatures and pressures significantly higher than current ultrasonic displacement sensors. The target processing environment for this sensor is that typically found in a hot isostatic pressure (HIP) vessel, i.e., temperatures exceeding 1000°C and pressures above 138 MP a."

Jan 1, 1997

By J. L. Liow

Studies have been carried out on the causes and effects of slopping in an annular cylindrical geometry such as the top submerged combustion reactor. Properties of standing waves formed such as the wave profile, period, pressure distribution and velocity have been derived analytically. The wear profile due to wave erosion was calculated based on the assumption of linear motion and that the wear is a dissolution process. The use of the j, factor showed that the wear was proportional to the square root of the wave velocity at any point. Using the dimensions of the lsasmelt reactor given by Errington et al. (1987)[11, the wear profile due to wave erosion was calculated using the analytical solution. The wear profile calculated was shown to have a maximum just below the initial bath surface. The wear was found to be concentrated in the region where the first asymmetric standing wave was most active. The results showed that the refractory near the bath surface will be affected by wave erosion, more so than any other parts of the reactor. The contribution of wave erosion on wear must be accounted for in assessing the total refractory wear of a vessel in which slopping exists.

Jan 1, 1991

By Frank A. Vonesh

In order to reduce the amount of visible, airborne emissions in the Metals Industry, a new Industrial Gas Technology was developed by Air Liquide. This patented technique is called ALECT?, Air Liquide Emission Control Technology. Demonstrations have been conducted for many cutting and lancing operations as well as for hot metal transfer from vessel to vessel. Fume reductions of 90% and greater have been achieved in actual practice. Air Liquide continues to improve the process and the associated control equipment.

Jan 1, 1994

By Gordon A. Irons, Diancai Guo

"Uneven movement of scrap during melting in an Electric Arc Furnace causes operation problems: cave-ins interrupt electric power input. The movement also influences the radiation heat loss to water-cooled side panels and roof. An apparatus has been built to simulate the flow of scrap that may be interlocked. It has been observed that flow starts at the point where the suspended length of the pile bottom reaches the average scrap size, and proceeds in the form of cave-ins, but scrap pieces slide with each other as ordinary granules. After a cave-in, the pile angle usually remains much larger than the normally observed angle of repose. The force balance of a partially suspended scrap pile has been analyzed, and the equivalent cohesion due to interlocking estimated. A numerical model has been developed to simulate the scrap flow. Simulated results agree reasonably with observed phenomena.IntroductionWhen one considers the melting of steel scrap in an electric arc furnace (EAF), it is helpful to understand the movement of the material during meltdown. As industrial experience demonstrates, scrap movement greatly affects EAF operation. In a typical operation, scrap is dropped into the furnace from scrap buckets. The roof and electrodes are swung into position, and power is applied to the electrodes situated over the scrap. The electrodes ""bore"" into the scrap by melting into the steel in the immediate vicinity of the electrodes as they are lowered. If solid scrap pieces gradually slide towards the arc area, the electric power supply can be maintained at a high level, with few interruptions or drastic electrode adjustments. This results in a high production rate and low power consumption per tonne of steel produced. On the other hand, if the charge moves down unevenly, i.e. in large surges, usually called cave-ins, the electrodes must be drastically raised, and power supply frequently interrupted. This is also accompanied by a high level of harmonics induced in the power network, deteriorating the quality of electricity supplied to other users.In addition, the movement of scrap in an EAF also influences the furnace heat efficiency, as the scrap pile is much closer to the electric arcs compared to the furnace wall and roof, and absorbs more radiated heat. Early exposure of the wall and roof to the arcs will increase the heat loss due to radiation, and reduce the service life of the furnace."

Jan 1, 2004

By I. Kim, J. C. Choi, W. D. Cho

"The effect of yttrium addition on the oxidation behavior of Fe3Al intermetallic compound was investigated in the range of temperature 800 to 1100 °C in 0.2 atm 02 in terms of oxidation rate and oxide adhesion. The oxidation rate of alloys, Fe-14.3 wt% Al and Fe-14.1 wt% Al-0.3 wt% Y, was nearly identical and the parabolic rate constant calculated as a function of temperature is Kp=5128 exp[-39506(cal/mol)/RT] mg2/cm4 hr.Rapid cooling and ultrasonic stress tests were carried out to test adhesion of scale formed on the alloys. While the oxide layer formed on the Fe-Al alloy without Y was found to be fragile and detached easily during the tests, the oxide layer formed on the Fe-Al alloy containing Y was protective, dense, and adhesive. The following two mechanisms were proposed to explain the adhesion improvement of Ah03 formed on the Fe3Al containing yttrium : (1) the addition of yttrium decrease generation of growth stress in alumina scale because the preferential diffusion of yttrium through grain boundary in alumina scale prevent internal oxidation of Al, one of main causes of growth stress, and (2) the second phase formed on the oxide scales prevents crack propagation through the scales, leading to better mechanical stability of the oxide scales.IntroductionIron aluminides have attracted the attention of many researchers as a candidate for use at high temperature because of their excellent oxidation resistance due to the formation of protective alumina scale. In order to resist aggressive environments at elevated temperatures, oxide scale formed on iron-uluminum alloy must satisfy the following three requirements : (1) thermodynamic stability (2) slow growth rate (3) adherence on substrate. According to Wallwork and Hed [l], the most suitable alloys for high temperature application are Fe, Ni, and Co alloys with the protection of Si02, Cr203, and Ah03 scales. While chromium oxide can vaporize as Cr03 above 1000 °C and silicon oxide may form low melting silicate [2,3], Alz03 has a high melting point and is the most stable among the three oxides thermodynamically [6]. In this respect, iron aluminides forming alumina seem to be most suitable for use at high temperature. However, alumina scale formed on the iron aluminum alloys tends to be easily spalled during oxidation due to the combination of growth stress and thermal stress."

Jan 1, 1998

By Katerina Kryst

Antimony and bismuth are two of the elements that need to be removed from copper electrolyte to ensure a trouble free operation as well as to maintain copper cathode purity. One method to control these impurities is the use of aminophosphonic ion exchange resins. Antimony is present as both Sb(III) and Sb (V). Sb(V) is very difficult to remove from these resins, requiring excess amounts of highly concentrated hydrochloric acid. In industry this affinity of Sb(V) for the resin causes a buildup of Sb(V) and degrading resin performance due to continual reduction of resin capacity. A new method for regeneration of aminophosphonic resins loaded with Sb(V) has been developed, which utilizes catalytic regeneration of the resin. Ion exchange can then be utilized for continual control of Sb and Bi in copper electrolyte.

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By G. A. Brooks

Reactive ball milling has been proposed as a new route for producing carbides from oxides through carbothcrmic reduction. It is claimed that through milling oxide and graphite powders to the nanoscale, amorphous materials with very high reactivity are formed, that allows for easy transformation of the starting material to another in a subsequent thermal process. Thermodynamic analysis of this proposed process suggests that unless particle sizes are reduced to below 10nm, then reduction in size alone cannot explain a change in the stability of oxides. Even with nanometer scale powders, the products formed need to have a lower total surface energy than the reactants before a chemical change will occur. A model developed by Bhattacharya and Arzt for predicting localized temperature changes based on milling conditions suggest that temperarure rises less than 400 K will be achieved in laboratory conditions. The present calculations suggest that nanometer scale powders formed through high speed ball milling (>10 mls) may have undergone a process analogous to melting and quenching. Further work is required to fully distinguish these features.

Jan 1, 2003

By Marcelo B. Mourão

An experimental investigation was carried out to -study the rates of reduction of pellets containing iron oxides by carbon dissolved in liquid iron, at temperatures ranging from 1720 K to 1973 K. Several different pellet types were employed; the materials used in the pellet's manufacture were pure hematite, two kinds of commercial iron ores, and mixtures hematite/silica and hematite/lime: Reaction times were determined employing the constant volume pressure increase technique (CVPI). It has been observed that the reaction rate increases as the temperature and the pellet's specific surface area increases. The reaction rate is also affected by the oxide type: pellets made from commercial ores or from mixtures hematite/silica or hematite/lime show reaction rates lower than those made from pure hematite.

Jan 1, 1996

By Charles Washburn

The authors review mercury sources, and contaminant streams, with particular emphasis on mercury that is extracted from precious metal ores. The design and operation of both large and small mercury distillation facilities are detailed. The relevant properties and characteristics of mercury and mercury vapor are presented. Facility engineering with respect to industrial hygiene, area ventilation, and material handling is presented.

Jan 1, 2003

By A. J. Duncan, S. Viswanathan, Q. Han

"Measurements of liquid permeability in the mushy zones of Al-15.42% Cu and Al-8.68% Cu alloy samples have been performed isothermally just above the eutectic temperature, using eutectic liquid as the fluid. A modified method has been developed to determine the specific permeability, Ks, as a function of time during the test from the data collected on these alloys. Factors affecting permeability measurements are discussed. Permeabilties are observed to vary throughout the experiment. This is attributed to rnicrostructural coarsening and channeling that occurs in the sample during the experiment. The permeability is related to the rnicrostructure of the sample using the Kozeny-Carman equation. The correlation between the measured Ks, liquid fraction, gL and the specific solid surface area, Sv, improves markedly when compared to previous studies in which rnicrostructural coarsening was ignored.IntroductionThe permeability of interdendritic liquids flowing through dendritic structures ·is an important parameter needed to predict the level of porosity in castings. The permeability is a component of Darcy's Law, used to estimate the pressure drop due to the resistance to the flow of interdendritic fluid to feed shrinkage. Therefore, much research has focused on measuring the permeability of alloys in the mushy zone (1-10). The Kozeny-Carman equation for liquid permeability in the mushy zones of alloys may be written as"

Jan 1, 1999

By Cheng Fang, Zhou Lie-xing, Peng Jin-hui, Guo Sheng-hui

This article discusses the behavior of temperature and microwave thermo gravimetric analysis characteristic of ammonium paratungstate in a microwave field. Experimental results show that when 12g of material is place in a microwave with 900W of power, paratungstate’s temperature rises at 70°C/min. This results in paratungstate’s temperature being 980°C after 14 minutes. Compared with thermo gravimetric analysis characteristic, former two-step process of paratungstate microwave calcined completed ahead of schedule, after two-step process reaction is more intense,Paratungstate warming is more rapidly, the reaction time is much shorter; According to XRD and SEM, the product is high purity, the crystal particle size is uniform, and the grain size is fine.

Jan 1, 2015

By Z. Y. Xie

The visualization techniques were employed for the analysis of computer simulation studies of dislocation core structure in ordered alloys. Atomistic computer simulation was used for the study of the local configuration of the material in the vicinity of the dislocation. Stresses were applied in the simulation in order to study the necessary stress level for the dislocation to move and onset plastic deformation of the material. The results were analyzed in terms of the strain tensor as a function of the position (x, y) in the material with the dislocation located at (0, 0). Various visualization packages are used to plot the invariants of this strain tensor and to visualize the changes that the dislocation core undergoes under stresses until it finally moves.

Jan 1, 1993

By Guohua Bai, Mingjun Rao, Jianchen Lim, Guanghui Li, Tao Jiang

"By using thermogravimetry, optical microscope and chemical phase analysis, the solid-state reduction of carbon-burdened chromite pellets in the absence and presence of additives were investigated. The effects of reduction temperature, reduction time and additives on the metallization of chromite pellet were studied. The results indicate that the pre-reduction ratio of carbon-burdened chromite pellets is improved with the increase of reduction temperature and the addition of additives. The metallization of chromium is increased from 63.9% to 92.8% at 1300 °C for 4h with the addition of 2 wt.% of sodium borate. Investigation suggests that the reduction of carbon-burdened chromite pellets is diffusion controlled. The apparent activation energy without additive is 192.1 kJ/mol, while it decreases to 170.4 kJ/mol in the present sodium borate.IntroductionFerrochrome is used to produce high strength, corrosion resistant, wear-resisting, high temperature resistant and oxidation resistant special steels, and it is becoming one of the most important alloy materials for the production of stainless and high alloying ferritic steels [1-5]. Demand for ferrochrome is steadily on the rise due to the growth of stainless steel industry. Nowadays, more than 80% of the world's ferrochrome is utilized in the production of stainless steel [6-7].Ferrochrome is mainly produced in submerged-arc furnaces (SAF) with chromite lump ore. However, lump ore merely accounts for 20% of the chromite ore output, while fine ore (< 8 mm) accounts for about 80% [8]. Therefore, agglomeration of chromite fine ore is necessary before charging into SAF."

Jan 1, 2011

By Junji Shibata

Zeolite synthesized from coal fly ash has many intelligent properties such as cation exchange, adsorption, catalyst and so on. The suitable use of the zeolite, however, is not established in an actual commercial scale yet. From the viewpoints of an effective usage of coal fly ash and the zeolite obtained from coal fly ash, we propose the new concept for environmentally friendly usage of zeolite, in which coal fly ash safely returns to the soil with growing plants and purifying wastewater. This method can make great contribution to recycle of coal fly ash, to purification of high nutritious water and to tree planting.

Jan 1, 2002

By Z. Smieszek, Z. Szota, P. Gajowski

"A new method for measuring the total quantity of suspensions contained in the electrolyte during copper electrorefining has been developed by the Institute of Non-Ferrous Metals, Gliwice. Electrolyte purity, and the suspensions content in particular, is of essential importance for the quality of electrolytic copper produced during the process. Suspensions contribute to the increase of slime impurities in electrolytic copper and increase losses in noble metals. Up to now, the laboratory method has been used for the· process control which provides analytical results with considerable time delay. Therefore, it is useless for the process control.The measuring method developed enables continuous measurements of a suspensions content directly within the stream of the flowing electrolyte. The principle of measurement is based on changes in optic properties of the electrolyte with varying suspensions content.1. IntroductionIn copper electrorefining, it is essential that the final product quality be maintained. If suspensions are present in electrolyte, the content of slime impurities in electrolytic copper, (such as Pb, Ag, Bi, Sn, Sb, and As), increases which can result in the occurrence of the so-called slime dendrites on cathodes, thus debasing the quality of the product. As a normal suspension content in electrolyte, the contents in the order of several mg/l are considered, usually not more than 5-6 mg/l, while contents exceeding 20 mg/l are referred to as an alarm state. Suspensions present in an electrolyte are usually a light fraction of anodic slime whose main components are metallic silver, lead sulphate, complexes of antimony and arsenic, and sometimes even calcium sulphate; they are mainly composed of very small particles of lead sulphate and antimony complexes. Sometimes - - in case of alarm states - - the so-called ""wandering slims"" can be observed, which are composed mainly of arsenic and antimony complexes. These ""wandering slims"" make a serious technological disturbance. In normal operating conditions of the electrorefining plant, an increase of suspension content can result from such reasons as crack of filter cloth in a slime filter, turbulent flow of the electrolyte, anodic passivation, aeration of the electrolyte, and improper servicing of an electrolytic tank. It is necessary to continuously control the suspensions content in electrolyte for proper electrorefining."

Jan 1, 1989