Search Documents

By J. -C. Tedenac, C. Colinet, X. Tao, P. Jund, R. Viennois

"We report an ab-initio study of the stability and electronic properties of transition metal silicides in order to study their potential for high temperature thermoelectric applications. We focus on the family M5Si3 (M = Ta, W) which is stable up to about 2000 °C. We first investigate the structural stability of the two compounds and then determine the thermopower of the equilibrium structure using the electronic density of states and Mott’s law. We find that W5Si3 has a relatively large thermopower but probably not sufficient enough for thermoelectric applications.IntroductionIn the search of new sustainable energies, thermogeneration of electricity is one of the promising ways, notably because it is able to produce electricity from different kinds of heat wastes and to its portability. However, despite recent progress in the field, the state-of-the art materials have specificities making their mass-production difficult or even impossible: toxicity (thallium, chalcogen or/and pnictogen based alloys), weak abundance (tellurium based alloys) or cost (germanium or rare-earth based alloys). For all these reasons, finding thermoelectric materials without these drawbacks is vital if we wish to use high temperature thermoelectricity for generating electricity in the near future. Due to their abundance, low cost and low toxicity, transition metal silicides are candidate materials of primary interest and the slightest advance in this field would immediately find an application for the thermogeneration of electricity."

Jan 1, 2011

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu

Jan 1, 2015

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By I. E. A. Aghachi

During static strain-aging of low carbon steel, when the material is pre-strained, the dislocation density increases. If totally or partially unloaded and aged for a prescribed time, interstitial solute atoms diffuse under the influence of the dislocation stress fields, thus tending to lock dislocations causing an increase in yield stress. If held for long periods at certain aging temperature, a decrease in yield stress (over-aging) is observed following the initial increase. This behaviour has been variously attributed to either recovery of cold worked dislocation structure and/or formation and coarsening of carbide precipitates. The present work demonstrates that, using a "process control" model for the competing processes of hardening and softening, dislocation recovery is responsible for over-aging of mild steel specimens under conditions tested during this investigation. Keywords: Strain-aging, Precipitation, Recovery

Jan 1, 2003

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

The carbon composite brick is a new refractory used in blast furnace hearth and bottom. It caused wide attention due to its high thermal conductivity and low erosion by molten iron. In this paper, chemical constituents, SEM-EDS and X-ray diffraction were carried out in order to understand reaction mechanisms. A series of experiments of oxidation resistance characteristics were made. The oxidation mechanisms of carbon composite bricks in the presence of air were analyzed. According to the analysis on many experimental results, the oxidation process of carbon composite bricks under different temperatures were controlled by different mechanisms. In the condition of high temperature, SiO2 as oxidation product hindered the diffusion of O2, and reduced the oxidation loss of graphite in the internal.

Jan 1, 2015

By Jenq-Gong Duh, Jyh-Wei Lee

"Hard chromizing process is a method for developing a surface modified coating providing wear, corrosion resistance and high temperature surface protection. Two carbon steels with 0.45 wt% and 0.95 wt% carbon contents, respectively, were chromized with pack cementation process at 950'C for 4 and 9 hours, respectively. The phase transformation and microstructure phenomena of chromized coating layer and matrix of two steels were studied with X-ray diffractometer and electron probe microanalyzer. (Cr,Fe)23C6 and (Cr,Fe)7C3 carbides and (Cr,Fe)2N1-x nitride phases were observed on the chromized surfaces. The thickness of chromized layers obeyed the parabolic rate law. The mechanism and diffusional kinetics of the chromizing process were proposed. The diffusivity of chromium in the (Cr,Fe)7C3 carbide phase was calculated using the moving boundary method.IntroductionChromizing process is one of the surface treatment technologies that can produce a chromium contained surface layer with sufficient corrosion and wear resistance on the steel matrix [1-7]. The relatively low cost and no ""line-of-sight"" restrictions are main advantages of chromizing. Adequate bonding strength of these coatings to the substrate was reported [7]. Chromizing process can be classified into soft chromizing and hard chromizing [2]. Soft chromizing is applied to steels containing less than 0.1wt% carbon through which chromium will be diffused. High temperature oxidation resistance improvement is the main purpose of soft chromizing process. On the contrary, the hard chromizing can be applied to steel containing more than 0.3wt% carbon, and very hard chromium nitride and carbide layers will be formed on the surface, which are very resistant to wear, corrosion and temperature [5-7]. In the previous studies on the Fe-Mn-Al-Cr alloy [5,7] and carbon steels [6], the thickness (X) of chromizing layers was analyzed and found the parabolic rate Jaw prevailed:"

Jan 1, 2004

By M. Kobayashi, Y. Nishisu

"Fine multicomponent particles of yttrium and europium were synthesized through the precipitation from homogeneous solution, and the various characteristics related with the fluorescence were investigated. The morphology and the fluorescent characteristics of the synthesized particles were affected by ionic species in the stock solution. In the presence of sulfate ion, some parts of the precipitated particles were aggregated, and _the fluorescent characteristics were not good. On the other hand, in the presence of chloride ion or nitrate ion, the particles precipitated were almost monodispersed, and, the intensity of the fluorescent emission were strong after calcination. Further, these particles were also very attractive as the red phosphor in the mercury-free fluorescent systems.Introduction Eu doped Y oxide particles have been widely investigated for the application to the fluorescent lamps and displays: Recently, the fluorescent lamps are pointed as harmful electric equipments because of using mercury for excitation. Therefore, the use of the mercury in the fluorescent- system will be limited or prohibited worldwide in near future. Then, the development of the mercury-free fluorescent lamp is strongly required without delay. Inert gas such as neon and/or xenon seem to be applicable as new excitation element that replaces the mercury. However, in case xenon the excitation wavelength,' 146 and 172nm, is different from that of the mercury, 254nm, and then, the commercial phosphors which are used in the present fluorescent lamp system are not available. Therefore, the invention of the novel phosphors is essential for the development of the mercury-free fluorescent lamp. Further, the controls of the size and shape of the particles precipitated are also important, because the homogeneity of the size and the shape is very important for the fabrication of the layer of the phosphor particles. That is to say, the development of the phosphor particles with controlled components, size and shape is essential. The precise control of size and shape improves the packing density, and so, the screen performance of the lamp [1]. In addition, these phosphor particles should be also useful for the application of the flat-plane displays, for example, PDP, etc. [2,3]. In the present work, first, the particles including yttrium and europium for the precursor for red phosphor were prepared through precipitation from homogeneous solution. This process was precisely controlled for the control of the components, size and shape of the particles precipitated. Next, the particles precipitated were calcined, and then, their fluorescent properties were characterized. As a result, some of them showed the possibly available characteristics as the red phosphor for mercury-free fluorescent lamp system. These experimental results are presented in this paper."

Jan 1, 2000

By Robert W. Bartlett

Biooxidation of an ore heap containing only a few percent of sulfide minerals requires insertion of a very large amount of oxygen either by natural air convection, forced air ventilation or gaseous diffusion. While shallow heaps, those with lateral distances much greater than their height, are of great interest for many heaped ore processing operations, natural convection is often ineffective for oxidizing them because of inadequate lateral flow into the heap's interior. Oxygen can diffuse into a shallow heap from its upper, horizontal surface in contact with air. Oxygen diffuses through the air-filled void space within the heap, driven by the oxygen concentration gradient resulting from internal oxygen depletion caused by mineral oxidation. Oxygen diffusion, coupled with the chemical reaction kinetics oxidizing the sulfide minerals, is analyzed for conditions of rapid mineral oxidation kinetics, requiring small mineral grain sizes, and for typical ore heap biooxidation parameters. Practical limits on heap heights are presented for effective biooxidation of the sulfide minerals within times of interest for heap biooxidation of refractory sulfide gold ores, one to three years.

Jan 1, 1995

By Serdar Aksu, Fiona M. Doyle

"CMP will be an essential process in the production of integrated circuits containing copper interconnects. This study aims to improve our mechanistic understanding of the role that organic chelating agents might play in the reactive slurries used in copper CMP. Copper dissolution behavior in EDTA arid glycine was first examined by producing potential-pH diagrams for the copper-water-EDTA and copper-water-glycine 'systems. The results of potentiodynamic polarization experiments were then considered in light of these diagrams. . In-situ polarization experiments were conducted to gain insight into the electrochemistry of copper during dynamic polishing in slurries prepared from EDT A and glycine.IntroductionCopper has recently started to replace aluminum as the interconnect metal in integrated circuits. Copper interconnection offers faster and more reliable integrated circuits due to its higher electrical conductivity and superior electromigration resistance (1). The damascene method is used to form multilevel interconnects in the manufacture of integrated circuit devices with copper metallization (2, 3). Copper is deposited by CVD or electroplating into vias and trenches etched in the interlayer dielectric (IDL), over a diffusion barrier usually made from titanium, tantalum or their nitrides. Chemical mechanical planarization (CMP) then prepares the wafer for the next deposition step, by removing excess copper and planarizing the surface. During CMP, the wafer is rotated and pressed against a rotating platen covered with a polishing pad. Chemically active slurries containing submicron size abrasive particles (Si02, Al20 3, ceria, diamond, etc.) are applied. Both the mechanical action of the abrasive particles and the chemical action of slurry constituents remove material from the wafer surface. Planarization results because material is removed faster from protruding regions on the surface than from recessed regions. Since CMP can globally planarize .the entire wafer, it has become one of the key technologies for producing integrated circuits with copper metallization."

Jan 1, 2000

By C. J. Lewis

This presentation concerns calcium oxide-better known as high calcium quick lime High calcium quicklime is produced by calcining high calcium limestone, mostly in the many rotary kilns located throughout the United States and Canada. This paper presents suggestions on the handling of lime based on field experience. The subjects covered are chemical analyses, transporta¬tion, lime storage, lime slaking to form a water slurry of calcium hydroxide solids, slurry transportation, slurry viscosity, and scaling of lime slurries. It is hoped that the comments on the foregoing areas will be of use to those designing or operating lime systems.

Jan 1, 1992

By Alan J. Hurd

"New insights into the development of microstructure in sol-gel films have recently been revealed by several diagnostic techniques, including imaging ellipsometry, ""chemical imaging"" by fluorescent tracers, light scattering from capillary waves, and finite-element modeling. The evolution of porosity during the continuous transition from dilute sol to porous solid in restricted geometries such as films and fibers is becoming clearer through fundamental understanding of evaporation dynamics and capillarity.IntroductionWith sol-gel processing, the full flexibility of solution chemistry can be exploited to make ceramic films and fibers with well controlled compositional characteristics. No less important is the ability to tune porosity and connectivity for specific applications such as optical and electrical coatings and membranes. Since the chemical and physical factors that determine the microstructure are not entirely understood, new diagnostics applied to sol-gel processing are welcome.Sol-gel films and fibers are distinguished by processing that takes a sol through continuous stages of increasing concentration and connectivity of a solid precursor. The liquid carrier is usually volatile or, at least, volatilizable through heat treatment. During deposition through states of increasing solids concentration, this sol might gel, as in bulk sol-gel processing, however, the gel state may be a fleeting transient that quickly empties of liquid. Nevertheless, the structures formed in solution during this stage influence the structure of the final solid. In particular, porosity is likely to be a remnant of networks formed in the sol-to-gel transition. Here we report on experiments whose goal is to discover the factors involved with porosity development."

Jan 1, 1994

By F. G. Prado

The technology for the extraction of zinc from zinc residues, such as zinc ashes, drosses and metallurgical flue dusts, by way of ammonium chloride solutions is well established, at least at the laboratory and bench scale levels. (3, 4) Zinc is soluble in ammonium chloride solutions in the form of zinc diammine chloride. Its solubility depends upon the concentrations and temperatures employed. The procedure and the equipment required are simple, and they can be applied either to small or large operations. As a by-product, zinc diammine chloride is produced with extremely low impurities in quantities which are stoichiometrically proportional to the zinc removed. The technology has been applied experimentally to galvanized steel residues. The dezincing results, including removal performance, energy and reagents required, and by-products are summarily presented in this paper.

Jan 1, 1992

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

By Jie Ma, Shun-Li Zhao, Jian Zhao, Jie-Yu Zhang

"Microstructural morphology evolution of Ni-45wt.%Mo droplets during rapid solidification process was investigated using an advanced modified 3D cellular automaton-finite element(CAFE) model by CALCOSOFT software. The model was modified by User-defined functions (UDFs) and validated with experimental solidification microstructural morphology of Ni-45wt.%Mo droplets available in the literature. Then, the influences of convection heat transfer coefficient, superheat of the alloy droplets and droplets size were investigated during the rapid solidification process. The predictions show that microstructural morphology is obviously sensitive to convection heat transfer coefficient and droplet size. With the decrease of convection heat transfer coefficient, the grain density decreases. In addition, the decrease of the droplet size could obtain refined microstructure. However, decrease the superheat ofNi-45wt.%Mo droplets has little effect on microstructural morphology.IntroductionFor several decades, much attention has been paid to undercooled alloy droplets of rapid solidification process for which can obtain refined microstructure, decreased microsegregation and extended solubility of alloying elements [1-3]. Extensive prior work shows that solidification of droplets plays an essential role in advanced material properties [ 4]. Consequently, it is very important to investigate the microstructural morphology evolution, especially for dendrite growth during non-equilibrium solidification process, for dendrite growth reflected the kinetics of the crystal growth process."

Jan 1, 2013

By E. Açma

In this study, the production of Cu, Co, and magnetic iron oxide from the ancient copper, slags, located in Küre-Turkey, is investigated. In the process under development, fayalitic slags containing 1% Cu, 0.43% Co are reduced in a D.C. arc furnace with coke or graphite additions. A metallic alloy, consisting of 3.8% Cu, 3.3% Co, 2.1% S, and the rest being Ice, is produced by granulation of the liquid metal. About 85% recoveries of Cu and C:o are achieved by hot sulfuric acid leaching of these granules followed by H2S precipitation. The, production of magnetic iron oxide is possible from the discarded leach solution, loaded v:ith FeS04, by using a method with geothite precipitation, dehydration, controlled reduction, and re-oxidation steps. The magnetic oxides produced have 20 m2Jg surface area, 1:8.3 aspect ratio, and the coercivity of 330-380 Oersted.

Jan 1, 1993

By José Roberto de Oliveira

Based on literature review one can see that the main objectives of MnO reduction is the comprehension of slag interactions and reactions with other elements beyond carbon. That's because it is worthwhile to study pure MnO reduction, where there will be not oxides interaction and just carbon will be the reduction agent. By a thermodynamic analysis we know that Si can react with MnO, then it's important to study this influence, so as Mn content. Our work aims to develop kinetics parameters for the MnO reduction, varying Mn and Si contents in bath. This has been given by pressure measure of CO in a Fe-C bath. The CO is generated by the oxide reduction with carbon. It has been proved that: - Mn content decreases the MnO reduction; - the MnO reduction is mainly influenced by Si content in a bath containing Iron, Carbon and Manganese so as Silicium

Jan 1, 1997

By J. McKelliget, J. Szekely, Oreper. G. M.

"1. INTRODUCTIONThis paper is concerned with heat and fluid flow phenomena in arc welding operations. Fig. 1 shows a schematic sketch of a typical arc welding arrangement. It is seen that an arc is being struck between an inert electrode and a metal surface and that the resultant current and energy flow will case the formation of a molten weldpool.It is clearly appreciated that the weldpool shape and the nature of circulation in the weldpool may play an important part in determining the ultimate weld quality. It is known, furthermore,· that the weldpool behavior in turn will be affected by the spatial distribution of the current and the heat flux it receives from the arc. Indeed, the inherent coupling between the arc and the weldpool is a key feature of welding operations.Up to the present useful work has been done on the modelling of heat transfer and melt circulation in weldpools (1,2,3,4) and also on the description of arcs, including welding arcs (5,6,7,8). However, the coupling between these two sets of phenomena is relatively unexplored in a qualitative sense. The purpose of the present paper is to examine the interaction between welding arcs and weldpools. The actual material will be presented under the following headings:"

Jan 1, 1986

By Li. Jiarong, Zuojian Liang, Qingyan Xu, Baicheng Liu, Shizhong Liu, Hailong Yuan

Single crystal solidification of turbine blades is a key technology for the production of reliable and high efficiency gas turbines. The solidification process of single crystal investment castings causes a number of problems that have to be solved such as the increase of casting defects and complexity of production process. Computer modeling and simulation is helpful to predict the defects and improve the process design. In the paper, a mathematical model for three dimensional simulation of solidification and single crystal growth of investment castings was developed based on CA, mechanism of crystal growth and basic transfer equations such as heat, mass transfer equations. Many factors including constitutional undercooling, curvature undercooling and anisotropy, which had vital influences on microstructure evolution, were considered in the model. Temperature, crystal growth interface and structure defects of investment castings of single crystal superalloy were investigated at withdrawal rates of 4.5mm/min and 7mm/min. Simulated results showed that microstructure evolution and structure defects were predicted reasonably and calculated results were coincident with experimental ones. The study indicated that three dimensional solidification simulation technique is a powerful tool for understanding the fundamental of solidification and the formation of structure defects in single crystal investment castings and finally for optimizing process design.

Jan 1, 2004

By Dewei Zhu

A general purpose computer model for describing the transport phenomena and resulting rate of deposition in Chemical Vapor Deposition (CVD) processes has been described. Partial differential equations describing the conservation of mass, momentum, energy and chemical species are solved by a computer program employing a finite volume method. The program allows for multiple chemical species and natural convection effects. In this paper, the deposition of silicon by the reaction of silicon tetrachloride and hydrogen in a vertical stagnation flow reactor with rotating substrate has been considered. The effects of reactor pressure and substrate rotation speed on the rate and uniformity of deposition have been studied. The predicted rates of silicon deposition along the substrate are in reasonable agreement with experimental results found in literature. The model can be used as a tool for design optimization of such reactors.

Jan 1, 1990

By Motoyasu Sato

Highly pure pig irons were produced in a multimode microwave reactor from powdered iron ores with carbon as a reducing agent in the nitrogen atmosphere. The grains in compacted powder absorb microwave energy selectively. Microwave-matter interaction creates thermal non-equilibrium state microscopically and enhances chemical reactions and the phase mixing at the grain boundaries very rapidly. The visible light spectroscopic techniques was used to monitor the progress of the reactions. Up to 650°C, the heated powders radiate the continuous spectrum of blackbody emission. The small non-equilibrium hot spots rise, move and finally burst in to brighter light emitting from all over the surface at 650°C. CN molecules and Fe (I) atoms were identified in the recorded spectrum. These bursts are similar to the ?ignition propagation? normally observed in chemical reactions. The line spectra originated from CO molecules have not been detected yet. The solid-solid reaction could be expected between the iron oxides and carbon to produce CO2 directly. A loss in the sample weight was accelerated during the excess-emission. These are the clear evidence that microwaves cause thermally non-equilibrium state and accelerate reduction process. The reduction of iron ore is completed at 1380°C and relatively very pure pig iron was produced. It should be noted that the impurity level of Mg, S, Si, P and Ti is only 5-10% of what is found in the pig irons produced by modern conventional blast furnaces in the steel industries. The necessary amount of carbon needed was 1/2 compared to conventional blast furnace to produce the unit weight of steel, if we applied renewable energy or nuclear power for the microwave excitations.

Jan 1, 2006