Search Documents

By O. Chemezov, Yu Zaikov, A. Apisarov, A. Isakov

"Silicon deposits containing 99,9 wt.% of main component were obtained by SiO2 electrolysis from chloride-fluoride melts. The operating temperature was varied from 973 up to 1073 K. The conditions for obtaining crystalline fibrous micro- or nanodeposits were determined. The deposits were investigated by ESM methodIntroductionThere are large reserves of natural quartz of high purity in Russia. Processing of this raw material by electrolysis in molten salts produces silicon containing 99.9 weight percent of basic substance.[1]This method is less energy-consuming in comparison to existing methods for producing high purity silicon from gas phase.Another advantage of the electrolytic method for producing silicon from its oxide in molten salts is the possibility of production of high-purity silicon under air atmosphere. It dramatically reduces costs of the electrolytic cell construction, and the operating costs at electrolysis.On our opinion, the main advantage of the electrolytic production from SiO2 in molten salts is a unique opportunity to obtain micro-and nanostructures of silicon deposits. In particular, it is possible to obtain fibrous structures of silicon. The electrolytic method allows smoothly adjusting the thickness and length of silicon micro- and nano-wires by varying the cathode current density and temperature of the process."

Jan 1, 2012

By Bowen Li, Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"Magnetic iron sulfide ore particles heat rapidly by microwave (MW) irradiation generating plasma during oxidation of surfaces. The high temperatures produced by the exothermic event decompose local portions of samples forming a differentiated flux of partially melted silicate (si-mt) with entrained metal-sulfide (sul-mt) droplets. The si-mt forms crystals of olivine (01) in Ca-rich pyroxene (Cpx) melt that resorbs a portion of iron sulfide (Po). The immiscible sul-mt droplets of (Fe,Ni,Cu)1-xS contain magnetic subsolidus Ni-pyrrhotite (Ni-Po) with Cr-bearing ferrospinel (Mag). Sub-micron sized flecks of Au are found on the surface of a sul-mt droplet with scanning electron microscope (SEM).IntroductionSulfide ore deposits supply the world's mineral resource in the production of non-ferrous metals. Particularly, Cu-Ni deposits are chemically enriched in metals from high sulfur saturation during magmatic formation that creates the proper geochemical environment for metals enrichment [1, 2]. The sulfur and oxygen fugacity control redox conditions of a differentiated silicate/sulfur magmatic melt with the concentration of iron playing a dominate role in the chemical partitioning of metals in sulfide liquid [3, 4]. The initial magnetic crystallization of (Fe,Ni)i-xS monosulfide solution (mss) from metal-sulfide liquid has an exclusive effect on the fractionation of mineral assemblages (zoning) [5].Phase equilibria of sulfide melt (sul-mt) components are related by a miscibility gap with mss forming Ni-rich pyrrhotite (Ni-Po) followed by the crystallization of (Fe,Cu)1-xS intermediate sulfide solution (iss) [6]. Precious metals form stable chacogenides and are retained in solution until the final liquid solidifies. The redistribution of metals now occurs by subsolidus cooling of mss and iss that exsolve low-temperature Fe-Cu-Ni bearing mineral assemblages [7]. The proper interpretation of ore genesis increases processing capabilities by isolating chemically enriched zones during extraction and should be used to aid in sustainable mine site development [8-11]."

Jan 1, 2013

By Yasuhiro Konishi, Kazunari Mizoe

"This paper describes a new processing of ultrafine, magnetic ferrites from sulfuric acid pickling solution in steel industry. In the ferrite processing, the iron (II) in the pickling solution was first oxidized to iron (III) by using the acidophilic thennophile Acidianus brierleyi. The bio-oxidized pickling solution was treated with solvent extraction to separate the iron (III) into the organic solution of tertiary aliphatic monocarboxylic acid. After that, the carboxylate solutions of iron (III) and other metal (cobalt) were hydrolyzed and precipitated ultrafine particles of crystalline ferrites at l90°C and l. 3 MPa for 20 min.IntroductionHot-rolled steel sheet has always a layer of oxides on its surface. The oxide layer arises as scale in hot rolling processes in steel industry, and the scale consists of the three iron oxides such as hematite Fez03, magnetite Fep4, and wustite FeO. Pickling removes chemically the scale layer that adheres to the steel surface. For normal steels, pickling is carried out in 15-20% hydrochloric acid at 60-70°C or in 20-25% sulfuric acid at 95-100°C. When steel is pickled with sulfuric acid, the scale oxides dissolve to give iron (II) sulfate.Spent pickling solutions are hazardous wastes containing a large amount of dissolved iron (II) and sulfuric acid, e.g., about 40 kg/m3 of dissolved iron (II) at pH 0. In typical commercial processes, spent pickling solution is usually cooled evaporatively to 5°C, and then to 0°C to crystallize iron (II) sulfate as its heptahydrate. After the crystallization operation, the sulfuric acid can be reused in the pickling operation.In this paper we describes a new processing of ultrafine, magnetic ferrite from sulfuric acid pickling solution, in order to recover dissolved iron (II) in the form of a valuable product. In the ferrite processing, the iron (III) was first supplied by the microbial oxidation of iron (II) in the pickling solution, and then the biooxidized pickling solution was treated with solvent extraction to separate the iron (III) into the organic carboxylate solution. After that, the carboxylate solutions of iron (III) and other metal (cobalt) were precipitated crystalline ferrites under hydrothermal conditions."

Jan 1, 2000

By A. Christlo

Short circuit detection in 1984 involved nine inspectors for production rates of 43,000 tpa. Trials indicated the feasibility of applying cell voltage monitoring to short circuit detection and improving operational efficiency. A computerised cell voltage monitoring system was commissioned in February 1986, to read voltages from 648 cells. The system incorporates 16 evenly distributed work face units which communicate with a central computer system. Provision has been made in the computer program for the automatic adjustment of cell reference voltages. This allows for the effect of polarization and other process variables which might other wise interfere with short circuit detection. The work face units can continue to work independently for several days should this become necssary. Current efficiencies have been maintained and the number of inspectors reduced from nine to five.

Jan 1, 1987

The U.S. Bureau of Mines investigated CaF2-assisted H2SO4 leaching to extract Mn from domestic silicate manganese resources. A pyroxmangite ((Mn,Fe)Sio3) ore containing, in pct, 34 Mn, 23 Si, 3 Ca, and 1 Fe was leached at 90° C for 3 h in a solution containing, in g/L, 12 Mn, 140 H2SO4, 130 (NH4)2SO4, and 5 CaFz. Manganese extraction of 92 pct was achieved. Manganese of greater than 99 pct purity was prepared by electrolyzing the purified pregnant solution at a current density of 50 mA/cm2. The current efficiency was 65 pct.

Jan 1, 1991

By Caisa Samuelsson

Experimental studies in laboratory-scale equipment have been carried out to study the vaporisation from dust generated during the copper converting process. In the present work the vaporisation of Zn, Pb, As, Sb, and Bi from a dust collected in the electrostatic precipitator after the copper converter were studied. The results show that Pb, Bi and As were vaporised to a high degree from the dust at a temperature above 900°C in a gas containing N2, SO2 and a small amount of H2. The vaporisation was high for these elements also in a gas containing N2, SO2 and 02 at temperatures above 1120°C. In an earlier study, thermodynamic calculations showed that it is possible to selectively condense metals at high temperature' in a gas atmosphere generated during a copper converting process. The present study was carried out to verify the thermodynamic model. The results indicate that it should be possible for a selective condensation of Zn at high temperature. The temperature required for a selective condensation of Zn is dependent upon the gas atmosphere, e.g., the oxygen potential.

Jan 1, 1998

By S Ivanaj

Oxidation of chalcopyrite from a copper concentrate in an electrochemical cell having separate-anodic and cathodic compartments was studied by potentiodynamic, potentiostatic and galvanostatic experiments. Oxidation of chalcopyrite particles was mainly realized by in-situ electrogenerated FeIII and Cull ions. The use of an ion exchange membrane, in this experimental set, avoids the reduction of the ferric and cupric ions. The effects of particle size, current feeder potential, current intensity and pulp density were studied to optimize the oxidation parameters. Selective complete oxidation of chalcopyrite was achieved. Oxidation of pyrite was negligible. Mom than 85 % of sulfur was obtained in its elemental form. This may allow selective extraction- of copper from the chalcopyrite concentrate without sulfur dioxide emissions.

Jan 1, 1995

By F. J. Tavera

Recently Jameson cell technology has gained acceptance in both mineral and non-mineral applications, mainly because of the high degree of contact between the involved phases in the downcomer, fact that leads to an efficient collection performance. The key for an acceptable performance of the downcomer operation depends on the stability of the jet zone, the mixing zone, and the plug flow zone. in this work the behaviour of the downcomer of a laboratory Jameson cell is reported, as a function of gas hold-up, superficial gas velocity, superficial liquid (or slurry) velocity, and length of the operating zones. The presence of carbon is evaluated in terms of its effect on the gas hold-up and bubble surface area flux. The influence of the downcomer operating conditions on the gas-liquid disengaging cell is presented. Keywords: Jameson cell, downcomer, gas hold-up, mixing, plug flow, conductivity.

Jan 1, 2003

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30t/hour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

By G. T. Lapidus

One of Society’s major concerns with hydrometallurgical processing is the large amount of water that is quintessential to its nature. This is especially troubling in arid areas, where the population struggles to procure potable water for their daily needs. For that reason, it has become our responsibility to conceive, design and implement processing schemes that not only use as little water as possible, but recycle streams within the plant itself and minimize waste that exits its perimeter. With this in mind, the conference will center on the importance of selecting the appropriate chemical systems and integrating material balances to avoid reagent overkill and to detect impurity accumulation. The three “R’s” (reuse, recycle and recovery) of aqueous solutions within the processes are emphasized. Examples of processes for the recovery of lead, copper, precious and PG metals from minerals and waste materials will be presented.

By Rush Kramer

A bulk compositional chemical analysis often provides incomplete information to help the mineral processor when faced with the problem of removing troublesome contaminants in low concentrations. Michigan Tech has developed a unique approach for addressing this problem. A combination of Scanning Electron Microscopy (SEM). Energy Dispersive Spectroscopy (EDS). and image analysis was successfully used to characterize the species responsible for phosphorus contamination of less than .05 weight percent in iron ore. An automated routine acquired the chemical signature of each particle on a backscattered electron image. The few particles containing phosphorus were identified from the hundreds of particles examined. and the phosphate phases present were easily characterized.

Jan 1, 1991

By K. Robinson

Following the longest Smelter campaign in BCL?s history it was planned to completely rebuild the flash smelting furnace in 1987. This was the fourth major overhaul and the most extensive so far attempted. Detailed planning took place over several year$ preceding the shutdown and implementation was completed in 54 days. The key to minimising shutdown time was the method designed for installation of the new uptake shaft and reaction shaft. Major repair work was also undertaken in the waste heat boiler and electric furnaces. Both of these activities had an impact on the critical path of the flash smelting furnace overhaul.

Jan 1, 1993

By P. R. Taylor

Laboratory experiments have been performed to evaluate the kinetics of roasting pyrite and arsenopyrite in air at elevated temperatures, in the presence of lime. The effects of temperature, time, air flow rate, particle size, lime type, and mineral/lime weight ratio on the rates of oxidation, lime sulfation, and lime arsenation were studied. The reaction products were identified using chemical analysis, x-ray diffraction, SEM analysis, and optical microscopy. The results are discussed in terms of the utilization of lime to capture sulfur and arsenic during the roasting of refractory precious metal concentrates. More than 99.9% of the arsenic and 98% of the sulfur are contained when roasting pyrite and arsenopyrite with hydrated lime under typical roasting conditions.

Jan 1, 1991

By Richard D. Hagni

Microscopic examination of selected, representative, unweathered samples of Birmingham, Alabama, Silurian, sedimentary iron ores has fully revealed the nature of the phosphorous-bearing mineral grains. The grains are composed of carbonate-fluorapatite (collophane), range in size from 1 um to 2.25 mm, and exhibit varied types of intergrowth with hematite. Modal analyses conducted under cathodolumi-nescence have provided quantitative data on the a3undance of each of 15 types of phosphorous-bearing mineral grains and made it possible to assess the potential phosphorous liberation from four types of iron ore. The results indicate that 27% of the total phosphorous contained in the iron ores in the western part of the Birmingham district can be expected to be liberated by fine grinding; 60% for ores in the eastern part of the district.

Jan 1, 1982

By Ian F. Hughes

"Concepts of an integrated steel plant for sheet products to be built and operating in the year 2000 will be described. The design and operating methodology of this market driven facility will integrate process uniqueness, standardization, manufacturing automation, artificial intelligence and information flow.An integrated steel plant for the year 2000 is defined for this article as one that will be built on a greenfield site and ""started up"" in the year 2000 with a capacity of three million tons per year of flat rolled products ranging from cold rolled and electrical steels to high strength formable steels and a full range of coated products.It may seem that the 21st century and the steel plant we're discussing are far into the future. The startling truth, however, is quite the opposite. As shown in Figure 1, even with accelerated development, a new process on which laboratory development work is begun today might just barely pass through the laboratory phase, pilot plant, and commercial feasibility stages such that it can be considered viable for construction and start up in the year 2000.On that basis, it is very unlikely that this 21st century steel plant will utilize any technology that isn't at least under investigation in the laboratory in 1988. As a result, we recognize that planning and selecting the facilities for this plant is, in fact, a pragmatic rather than futuristic process, and that its main value is in providing a bridge to longer-term predictions."

Jan 1, 1988

By Michael Zinigrad

The quality of metallic materials depends on their composition and structure and these are determined by various physico-chemical and technological factors. To effectively prepare materials with required composition, structure and properties it is necessary to carry out a research in two parallel directions: Comprehensive analysis of thermodynamics, kinetics and mechanisms of the processes taking place at the solid-liquid-gaseous phase interface during welding processes and development of mathematical models of the specific welding technologies. We have developed unique method of mathematical modeling of phase interaction at high temperatures. This method allows us to build models taking into account the thermodynamic characteristics of the processes, the influence of the initial composition and temperature on the equilibrium state of the reactions, the kinetics of heterogeneous processes, the influence of the temperature, composition, hydrodynamic and thermal factors on the velocity of the chemical and diffusion processes. The model can be implemented in the optimization of various technological processes in welding, surfacing, casting as well as in manufacturing of steels and non-ferrous alloys, materials refining, alloying with special additives, removing of non-metallic inclusions.

Jan 1, 2003

By Xingming Zhang, Huawei Zhang, Yanxiang Li

"A hybrid porous metal with nano-micro double scale pore size and regular-random bimodal porous structure has been fabricated by unidirectional solidification of a lotus-type alloy followed by dealloying treatment to the base alloy. The base alloy selected is a Cu-Mn binary alloy. The lotus-type porous Cu-Mn alloy with straight pores of several hundred micrometers in diameter was manufactured by unidirectional solidification with a mould casting process. Dealloying treatment was then done to the lotus-type porous structure of Cu-Mn alloy. The solid Cu-Mn alloy wall of the lotus-type porous structure was transformed to random porous structure of dozens to hundreds nanometers. The influence of corrosion parameters, such as the current and time in electrochemical corrosion, temperature and corrosion agent in chemical corrosion, on the nano-porous structure formed has been studied systematically.1. IntroductionA hybrid porous metal is a kind of cellular structure with different porous or cellular forms inside, which possesses special properties and can be applied in many fields as fuel cells, catalysis, sensors, etc. Several means have been developed to fabricate this kind of porous material [1-2]. In this paper, a novel process of Gasar plus dealloying is introduced to fabricate a new form of hybrid porous metal with nano-micro double size and regular-random bimodal structure.The Gasar process, also called the metal-gas eutectic directional solidification, that invented by Shapovalov [3] in Ukraine and now in USA some twenty years ago, is used to fabricate porous metals with regularly aligned pores basing on the solubility difference of a gaseous element in solid and liquid metal. Nakajima and his colleagues [4] in Japan studied this process further and called this kind of structure a lotus-type porous metal. They put more attention to various fabrication techniques and properties of lotus-type porous metals. Li heading a group [5-6] in P.R. China studied the mechanism of Gasar process and process controlling techniques. The Gasar pore structure and porosity can be controlled by processing parameters, and a regular Gasar structure with oriented pores distributing uniformly in the solid matrix can be obtained under optimized processing parameters."

Jan 1, 2014

By Michael J. Nicol

Growing environmental and occupational safety concerns about the use of cyanide in gold processing has increased the interest in more acceptable alternatives. The most likely of these is thiosulfate. However, the thiosulfate process lacks a proven in-pulp method of recovering the dissolved gold, because activated carbon is not effective for the absorption of the gold thiosulfate complex .. Anion exchange resins do offer a possible route for in-pulp recovery. This paper describes work aimed at the evaluation of the effectiveness of commercially available anion exchange resins for the recovery of gold from thiosulfate leach liquors? and pulps. It has been found that strong-base resins are superior to weak-base resins in that they have a larger capacity, which assists in reducing the competition from other anions within a leach solution. Further studies with a selected commercial strong-base resin have shown that competing polythionateanions (particularly tri-and tetrathionate). Lower the maximum possible gold loading but that gold is selectively recovered over other base metal anions in solution. Kinetic experiments found that while? competilig anibns did not affect the initial rate? of gold loading it was important to minimise the contact time of the resin in solution so to prevent displacement of loaded gold by competing anions over longer times. A small-scale resin-in-pulp plant investigation showed gold can be recovered from a leach pulp by a strong-base resin to yield gold loadings of 3000 mg/L, barren pulp containing less than 0.05 mg/L of dissolved gold and. copper loadings of 500 mg/L. Loaded copper was displaced gold and at a loading of 2000 mg/L gold the copper loading was minimal «500 mg/L). The resin was found to recover gold adsorbed on the solids that would, otherwise have. reported to tails if a solid/liquid separation method were used. A patented two-step elution process in which copper and then gold are separately eluted from the resin is also discussed.

Jan 1, 1998

By W. -D. Schneider, B. Schwab

Like all metals, zinc can be recycled theoretically without end. To demonstrate environmentally friendly use of zinc, it is necessary to increase the recycling rate. In this regard, the Imperial Smelting Process developed in the forties and fifties in the United Kingdom has become more and more important. This unique process combined with a sinter plant, hot briquetting, and direct injection through the ISP furnace tuyeres offers ideal possibilities to recycle all kinds of zinc and lead bearing materials. Possible secondary materials include Electric Arc Furnace (EAF) dust, zinc-containing sludges and even zinc/carbon batteries. This high temperature process also destroys all organic materials, like dioxin, and can be seen as a sink for many harmful substances.

Jan 1, 2000