Search Documents

By Shubin Wang

Copper(II) and nickel(II) are often recovered from ammoniacal alkaline solutions by solvent extraction using hydroxyoxime extractants: both copper(II) and nickel(II) are extracted from ammoniacal alkaline solutions and, from the loaded organic phase, nickel(II) is selectively stripped with a dilute acid followed by copper(II) stripping with an acid of higher concentration. Since a small portion of ammonia is co-extracted with copper and nickel, the extracted ammonia should be scrubbed using a dilute acid before metal stripping. In the present study, a mechanistic model has been developed in order to support design and control of this process. The equilibrium distribution ratios of copper(II), nickel(II), and ammonia at 298 K using LIX® 84-I (active component, 2-hydroxy-5-nonylacetophenone oxime) as the extractant are successfully correlated by considering the relevant equilibria. Based on these results, quantitative prediction of equilibrium distribution ratios in the process has been made possible, and suitable conditions for the efficient separation of copper(II) and nickel(II) are discussed.

By Jie Li, Thomas A. Rawdanowicz, W. J. Collis, S. Venkatraman, S. Iyer

"InSb being the lowest band gap. material amongst the 111-V semiconductors with low effective mass has long attracted research interest, due to its potential application in far infrared devices and for high speed circuit elements. In this paper, we report, for the first time, Te-doping of InSb on GaAs substrate using SnTe doping source with molecular beam epitaxy (MBE) technique and its electrical characterization. The undoped epilayers are n-type in the temperature range of 10 K to 300 K investigated. The room temperature (RT) mobility as high as 64,810 cm2/V·s (1.9x1016 cm-3) have been measured on a 4.8 µm thick epilayer. Sn Te doping at different doping levels were investigated. 5. 7 µm thick doped layers with RT carrier concentrations ranging from 2x1016 cm-3 to 3.2x1018 cm-3 with corresponding full width at half maximum (FWHM) of x-ray (400) rocking curve varying from 170-200 arc-seconds have been achieved. The Hall mobility of 20,000 cm2/V·s at 1.3xl018 cm-3 carrier concentration was obtained indicating that SnTe is a good candidate as source material for n-type doping of InSb.IntroductionThe thin films of InSb and InSb-based alloys have found considerable interest because of potential applications in III-V semiconductor-based infrared optoelectronic devices1• In addition, the advantage of the small effective mass and the consequent high mobility can be utilized in high frequency and high-speed circuit devices2 InSb can also be used in magnetoresistive sensors for position sensing3. Epitaxial InSb films grown by MBE may be doped n-type with Si or Sn, or with the group VI elements, namely, S, Se, or Te. Of the group VI elements, Te may be advantageous because of its relatively low vapor pressure. However, the vapor pressure is high enough to have sufficient memory effect during MBE growth. Hence different telluride compounds such as GaTe45, PbTe6 and Sb2Te37 have been used as the dopant source for Sb-based compounds. SnTe has also been used as a successful n-type dopant in the MBE growth ofGaSb8 But, to our knowledge, there is no report on the investigation of SnTe doping of InSb. In this paper, we report the first doping characteristics of SnTe in InSb layers grown on GaAs substrate."

Jan 1, 1998

By Ashwini Kumar

Flame impingement on the burden is routinely encountered during the initial phase of melting in aluminum reverberatory furnaces. This impingement causes an obstructed pathway for the hot gases, and hence the circulation and residence time of the hot gases are greatly impacted. Moreover, as the load melts, the flames gradually achieve an unobstructed path leading to reduced gas residence times. This flame impingement and constantly changing combustion space volume will lead to vastly different fuel and oxidizer mixing patterns and thus affect the overall furnace performance. Fine tuning the burner operating conditions such as flow rates and injection angles with the changing combustion space could result in significant improvements to the furnace efficiency. However, one has to gain a better understanding of the furnace dynamics to know the suitable parameters to adjust. Physical modeling can be elaborate and expensive to conduct on a regular basis while Computational Fluid Dynamics (CFD) can cost-effectively address this challenge. In this study, the furnace model is created with a particular loading pattern to understand the flame dynamics in the presence of a piled load. This configuration can be thought of as a computational model of the furnace with the burden at a particular stage of the melting process. Thermal efficiency and behavior of the furnace are quantified and the predicted values are compared with the operational data from an experimental reverberatory furnace.

Jan 1, 2008

By Hua Hou, Xiaofeng Niu, Wei Liang

"The explicit finite difference (EFD) method is used for calculating the casting temperature field during solidification. Because the time step is limited, the computational efficiency of the EFD method is lower. In order to improve the computational efficiency, a fourth-order in space and second-order in time model based on the equivalent specific heat method and the alternating direction implicit (ADI) method is established. The degree of similarity between the simulation results and the experimental results is analyzed. The results show that the simulation results of this high order mathematical model are close to the experimental results.IntroductionThe 3D heat transfer equation of temperature field during solidification process is as the following: [1-3]."

Jan 1, 2013

By Yong Hwan, Wang Jian-Jun, Cai Jiu-Ju, Chen Chun-Xia

"The quantity of residual-heat and its recovery in some Chinese sinter plants are investigated. The main factors affecting energy consumption are analyzed using exergy analysis combining energy level analysis. It is indicated that the “gradation recovery and cascade utilize” of discharged gas and sinter residual heat in different temperature is the direction and the available approach to reduce energy consumption of the sinter process. Taking an iron& steel enterprise as an example, the three-ranked scheme of residual-heat recovery is put forward: ?Part of the sinter gas is used for warm-up and dryness; ?The high-temperature part of the cooler and exhaust-heat boiler are actualized as a closed-circuit, which can produce high-quality steam to generate electricity. ?The waste air in low-temperature part is introduced to sintering machine to support combustion. According to the CDQ which can recover the coal heat, the assumption of pot-recovery is put forward to replace the belt cooler. The two equipments of residual-heat recovery are analyzed in the aspect of energy consumption and CO2 reduction.1. IntroductionEnergy consumption in sintering is only inferior to iron-making in iron& steel enterprises, accounting for 10%~20% of the total energy consumption. A lot of residual heat is produced during sintering, and mostly from the sinter ore and waste gas. Sensible heat of hot sinter ore and discharged gas have accounted for 60%[1] (equals to 40 kgce/t-ore), which are the key point of sintering waste heat recovery. Discharge gas of sintering is mostly composed of flue gas deriving from sinter bed’s combustion, and the content distribution of H2O and O2 and the temperature of the gas along the length of belt-type sintering are shown in Figure1[2,3]. Currently, the sensible heat of hot sinter ore is mainly recovered by circular cooler and cooled by blasting air: the temperature of cooled discharge gas brings down from 350? to about 100? along with the decrease of sinter ore temperature. It is significant to recovery and reuse the waste heat as 4000~6000m3 discharge gas per ton of ore can be produced"

Jan 1, 2008

By Liu Zhonghua

Hydrogen reduction of cobalt sulfide (Co9S8) was experimentally investigated in the temperature range 813-1053 K. The results revealed that the reaction kinetics can be described by the shrinking core mod¬el in chemical control regime at low temperatures, it is of first order with respect to hydrogen concentration, and the reaction activation energy is 67.4 kJ/mol. The SEM second electron images of the samples before and after experiments showed that the swelling of the sample above 973 K is due to the formation of metallic cobalt whiskers.

Jan 1, 1992

By Jiang Fan, Wang Haigang

"The three-dimensional complex multiphase turbulent flow in U-beam separators was simulated using the Reynolds stress equation models (RSM). To account for the effect of the stochastic characteristic of the instantaneous gas velocity on the particles, the improved Lagrangian stochastic model based on the Reynolds stress model for gas phase was adopted, which attributed to the successful prediction of the turbulence anisotropy and particle crossing trajectories effects. The interaction between the particles was also considered using the HardSphere model. To treat the particle-wall collision, the influence of the roughness of the wall on the motion of the solid particles was taken into consideration by imposing random collision angles. The result from this study not only shows the dynamic characteristics of the multiphase flow- in the separators, but also gives the relationship among the efficiency, structure and pressure losses of the separator.IntroductionCirculating fluidized bed (CFB) combustion is one of the most promising clean coal techniques. A main feature of CFB boilers is the un-delayed recycle of solid, coal and sorbant particulate, in an external loop. Separator, which is required to separate the solid particle from the flue-gas leaving the reactor of CFB, plays an importance role in the external solids recycle loop. It affects the combustion of CFB system greatly. Presently cyclone is the most commonly used as separators for CFB system and other chemical industrial processes. It provides high level of separation for CFB system for fine particles. However it suffers from some inherent disadvantages. It's volume and size is huge. Moreover, it is difficult to design and install when the CFB workload rises. The application of U-beam separators instead of hot cyclone separators in CFB boilers has many advantages. Publications indicate proposals or successful use of Ubeam separators in Swedenr11, USA 21, Russia r3land China [4]• But it is not possible to find results in the literature of detailed investigations of this new. type of separators or recommendations on the choice and calculation of an optimal design. For this reason, numerical simulation for the three-dimensional gas-particle two-phase flows with several rows of vertical U-beam elements, local in the chess order and blocking a way of outgoing from a CFB boilers dusted gases was carried out in this study."

Jan 1, 2004

By M. Misra

The bacterium?Mvcobacterium Phlei has a demonstrated potential to be used for the flocculation of a variety of finely divided minerals. The microorganism possesses both hydrophobic surface and high negatively electrostatic charge. It can adhere to many mineral surfaces ?if the charge and hydrophobic interaction? between the microorganism and the minerals are favorable to adhesion. Experimental results showed that the dolomitic phosphate slime from Florida and fine hematite can be :readily flocculated from dilute suspension.. In the case of dolomitic phosphate slime, a consolidated sediment containing 24'-25 weight% :solids can be obtained from .a dilute slurry .in a short time. Sediments obtained from hematite flocculation are rather massive and more .consolidated than phosphate slime. Mycobacterium Phlei has a specificity for selective flocculation of hydrophobic fine coal particles from pyrite and ash containing minerals. Because of mutual hydrophobic interaction of coal and Mycobacterium Phlei, it was noticed that coal particles appear to be strongly held in the aggregate by adhesion or bridging of bacteria. However, Mycobacterium Phlei is not a good flocculant for either associated pyrite or ash present in coal.

Jan 1, 1991

By Stavros A. Argyropoulos, Henry H. Hu

"The assimilation of exothermic additions in liquid metals exhibit an array of unique coupled heat, mass and momentum transport phenomena. These phenomena are further complicated by the presence of a moving boundary.This paper describes a) A mathematical model which simulates the complex phenomena, and b) An extensive verification of the mathematical model. The SIMPLER algorithm was employed to solve numerically the pertinent partial differential equations. The computational results indicated that the exothermic heat of mixing led to a rapid increase in temperature around the moving boundary, which produced an enhanced convective flow in the liquid phase. The intensification of fluid flow around the moving boundary resulted in an acceleration of the melting process.Verification of the model was carried out in two contexts. The first was, in a low temperature physical model consisting of ice immersion in different sulfuric acid solutions. In this physical model, both temperature and velocity measurements were carried out. The model results were compared with experimental measurements and they were found to be in excellent agreement. The second context employed high temperatures, involving the assimilation of silicon in high carbon liquid iron. The model was also applied to predict fluid flow, heat and mass transfer for these high temperature experiments and a good agreement was obtained.In addition new dimensionless heat transfer correlations that quantify these complex phenomena will be presented."

Jan 1, 2001

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By T. T. Chen

A mineralogical study of copper anodes and copper anode slimes was carried out to elucidate the silver phases present and the behaviour of silver during copper electrorefining. Most of the silver in the anodes is in metastable solid solution in the copper metal. As the copper dissolves, silver also dissolves, but is rapidly removed from solution by a variety of reactions. Some of the silver is precipitated as Ag by cuprous ions and some is precipitated as a complex CU-Ag-Pb-As-Se oxidate phase. Much of the silver, however, reacts with copper selenides to form, progressively, (CU,Ag) 2se, AgCuSe and Ag2se. The reaction commences at the periphery of the selenide grains and progresses inward; the result is commonly a silver-rich species on the outside of a silver-deficient core. Slimes collected periodically throughout the electrorefining cycle show a progressive silver enrichment of the selenides. Traces of Ag2Te also may be present, but the telluride seems to J:ie a rare constituent of most raw anode slimes.

Jan 1, 1989

By W. F. Ranson, R. C. Progelhof

"I. THE PROBLEM: MANUFACTURING PRODUCTIVITYThe 1985 President's Commission [I] on Industrial Competitiveness found compelling evidence of the declining economic position of the United States in world markets. The annual rate of increase in the United States productivity is approximately one-seventh that of our major trading partners over the last decade: profit levels in manufacturing investments are below those of the mid-1960's; an increasingly negative trade balance since 1971; and a sharp decline in the United States share of world trade in manufactured goods for more than two decades. A particularly dramatic example of the shifting economic balance is the fact that Japanese productivity growth has been five times greater than that of this country since 1960. In face, Japan's productivity now exceeds that of the United States in such critical industries as steel, transportation equipment, electronics and electrical machinery.American employees have experienced the competitive consequences of this nation's lagging industrial performance. Between 1980 and 1984 alone, the population of non-farm employees engaged in manufacturing dropped from 22.4% to 20.6%. This reduction in manufacturing must be arrested.Commissions RecommendationsThe comprehensive set of recommendations offered by the President's Commission recognized the nation's ""key competitive advantages"", technology and human resources, and calls for their strengthening. Particular emphasis is placed on manufacturing technology and the fact that this country does not translate research into new technologies rapidly and fully.""Perhaps the most glaring deficiency in America's technological capabilities has been our failure to devote enough attention to manufacturing or 'process' technology. It does us little good to design state-of-the-art products if within a short time our foreign competitors can manufacture them more cheaply. The United States has failed to apply its own technologies to manufacturing. Robotics automation and statistical quality control were all first developed in the United States but in recent years they have been more effectively applied elsewhere""."

Jan 1, 1988

By Alicia Esther Ares, Carlos Enrique Schvezov, Alejandra Silvina Roman, Claudia Marcela Méndez

In this paper the structure of aluminum based alloys and their corrosion behavior by using different electrochemical techniques as characterization methods are considered. Currently, it becomes imperative to know the role of the Al2Cu against the susceptibility to corrosion of these alloys. The present work aims to studying the electrochemical behavior of aluminum base alloys with the following compositions: Al-1wt.%Cu, Al-4.5wt.%Cu and Al-15wt.%Cu (with different grain structures), in 1M NaCl solutions, at room temperature. Cyclic potentiodynamic polarization tests were performed and were found that the alloys with more than 1wt.%Cu in the matrix have an unstable behavior and without tendency to reach passivity. The equivalent circuits derived from electrochemical impedance spectroscopy technique (EIS) generally showed two capacitive contributions. The susceptibility to corrosion becomes a complex function, not only of copper concentration and structure, but also with interdendritic spacings and distribution of phases in the alloys.

Jan 1, 2015

By Milton Manrique, Edgar E. Vidal, Patrick R. Taylor

"Ultrafine zirconium carbide powder has been synthesized using zircon concentrate and methane in a thermal plasma reactor. The effect of several experimental variables, such as power used and zircon particle size, on the conversion has been studied. A thermodynamic analysis of the possible reactions and stable compounds was performed. A mathematical model that describes the in-flight decomposition of zircon particles was developed based on a description of the temperature and velocity profiles calculated in the reactor. It was shown that the formation of zirconium carbide from zircon and methane is thermodynamically possible. Complete 'vaporization of zircon in the reactor is predicted when the particle size is below 45flm and the effective power entering the reactor is 15 kW. The powders were collected and characterized by XRD, SEM, TEM and chemical analysis using ICP. Results of the product analysis indicated the presence of zirconium carbide, zirconium oxide, silicon carbide and silicon oxide.IntroductionIn recent years there has been an increased interest in the production of nanometric sized powders of ceramic materials for use in advanced materials applications. One possible method to produce these powders is with a thermal plasma reactor, which offers high temperatures and fast quenching rates. This technology has been called - Thermal Plasma Synthesis - [1].Zirconium Carbide (ZrCx) has typical properties of transition metal carbides: elevated hardness - between alumina and diamond - a high melting temperature of 3420°C and high chemical stability at room temperature [2]. ZrCx has a Bl crystal structure with deficiencies in the number of carbon atoms in the cell with x between 0.6 and 1 [3]. Different methods have been used to produce ZrC, one method is by direct reaction of zirconium hydride or halide with carbon. Other methods used are direct reduction and carburization of zirconium oxide (Zr02) and reaction of metallic zirconium with a caburizing gas such as acetylene [3]. Recently small films of ZrC have been obtained using a sputtering device [4,5]. ZrC has been used in nuclear plants as a low neutron absorbing and high mechanical resistant refractory material and also as a constituent in cathodes made of UC-ZrC [6]. It is also used in the form of tubes, boats and crucibles to handle molten metals and as part of electronic devices used for thermoionic transducers. Recently ZrC has been used along with zirconium diboride (ZrB2) to produce composite materials [7,8]."

Jan 1, 1996

By Tian Sugui

By means of the long-term aging treated, creep properties measuring and microstructure observation, an investigation has been made into the microstructure and creep behavior of the casting and rolling GH4169 superalloy after long-term aged. Results show that, after the casting and rolling GH4169 superalloy treated by long-term aged, significant amount of " phase are dispersedly precipitated within the grains of the alloy, and some of the NbC, Cr7C3 carbide are distributed along the grain boundaries. In the range of the applied stresses and temperatures, the creep activation energies and stress exponents of LTA GH4169 alloy during steady state creep are calculated to be Q=541.1kJ/mol and n=16.2, respectively. During creep, the deformation mechanism of LTA GH4169 is thought to be the twinning and dislocation slipping within the twinning regions, and the damaging mode of the alloy is the intergranular fracture, and the non-smooth crystal surface is displayed in the fracture regions of the alloy. Thereinto, the carbides film formed along the grain boundaies has a few effect on the strength between the boundaries, which is a main reason of resulting in the alloy possessing a longer creep lifetimes.

Jan 1, 2009

By He Zhi-jun, Ning Zhe, Pang Qing-hai, Zhang Jun-hong, Zhan Wen-long

The effect of microwave irradiation on grinding property of coal was studied by using Hardgrove grindability index tester. Superior grindability of coal was obtained to varying extent after microwave irradiation treatment. The variation in microstructure of pulverized coal during microwave irradiation was observed by utilizing scanning electronic microscope (SEM). The results indicated that the different microwave absorbance of minerals and carbon matrix led to cracks on their interface, by which coal particles were further pulverized and therefore the granularity of coal powder was reduced. Due to the different formation process of various coals, bituminite and anthracite are very different in physical and chemical properties. According to the content of coal pulverization, it can found that microwave irradiation has a stronger pulverizing effect on bituminite in comparison to anthracite.

Jan 1, 2016

By G. Scavino

A 0.5 wt.% C, 22 wt.% Mn austenitic steel, recently proposed for fabricating automotive body structures by cold sheet forming, due to favorable overall strength and ductility, exhibits plastic localizations during uniaxial tensile tests, whereas no localization happens during biaxial Erichsen cupping tests. Full-thickness tensile and Erichsen specimens, cut from as-produced sheets, were polished and tested at different strain rates. During the tensile tests, the plastic localization phenomena consist first of macroscopic deformation bands traveling along the tensile axis, and then of series of stationary deformation bands, each adjacent to the preceding ones; both types of bands involve the full specimen width and yield macroscopically observable surface relief. No comparable surface relief was observed during the standard Erichsen tests. The stress state being known to influence plastic localization phenomena, reduced-width Erichsen tests were performed with 10 to 30 mm width polished specimens, in order to explore the transition from biaxial to uniaxial loading.

Jan 1, 2009

By G. Belardi

A study has been conducted to assess a new wet beneficiation treatment for the recovery of the sulphuric-acid-soluble titanium oxide contained in the waste from an Italian TiO2-pigment facility. The waste is produced during treatment of a Ti-enriched slag and contains as main components TiO2 (54%, of which 42% acid-soluble and 12% insoluble), SiO2 (27%) and A1203 (6%). Eighty percent of the material is finer than 50pm. The first step was to ascertain the possibilities offered by size classification, wet gravity separation, froth flotation and wet high-intensity magnetic separation to improve the grade and recovery of Ti02 and reduce the SiO2 content. The next step was to optimize the operating conditions of the various separations and assemble them into a complete flow- sheet. Beneficiation ensures potentially 70% recovery of the TiO2 with a concentrate grade of 80%.

Jan 1, 1998

By J. S. Lee

A new high performance adsorbent is synthesized by the sol-gel method and applied to the removal of cadmium and mercury ions from aqueous solutions. Adsorbents based on metal oxides have been developed by immobilizing chelating molecules on the surface of the existing metal oxide networks and show ability for selective metal extraction from aqueous solutions. However, efficiencies of such adsorbents are limited due to low ligand density, and difficulty in pore accessibility. These difficulties are circumvented by synthesizing adsorbents using the sol-gel technique. In one example to be discussed, the sol-precursor possesses an organic moiety that binds cadmium, mercury, and copper ions. The capacities of 1.98mmol Cd(II-/gm and 6.40 mmol Hg/gm of this adsorbent are considerably higher than those of adsorbents prepared by the ligand immobilization technique. The scope of this paper is to discuss the development of the new adsorbent and its applications for cadmium and mercury removal from aqueous solutions.

Jan 1, 1999

By D. H. H. Quon

Results of a study conducted to determine the properties of iron ore pellets made from Mount Wright and Carol Lake ore concentrate fines with partial and full substitution of bentonite by several organic binders are presented. Carboxy methyl celluloses 7H and 6TL, hydroxy ethyl cellulose (natrosol) and modified guar gum all produce pellets of acceptable wet, green and dry strength. However, when fully substituted, an inorganic binder such as calcium carbonate is required for satisfactory strength development after induration. Mixing the Carol Lake ore with Mount Wright ore in a 50-50 ratio also achieves the same result. The failure of the Carol Lake ore in the pelletization process is attributed to the low hematite content of the ore. The results are very similar to those from the extrusion studies reported earlier (8).

Jan 1, 1989