Search Documents

By Shengli Wu, Mingyin Kou, Feng Chang, Laixin Wang, Hua Lu, Jianliang Zhang

Sintering dust has been regarded as an important secondary resource in a modern steel plant. Sintering dust was mechanically treated using different milling machines and experimental conditions in air atmosphere. The changes in phase constitution, particle size, specific surface area, particle morphology, and lattice parameters of activated sintering dust were determined. It was found that the agglomeration of the particles take place during extended dry milling with accessible pores for Nitrogen gas. The maximum specific BET surface area in the stirring wet grinding and planetary wet grinding increases to 43.06 and 46.45 m2/g after activated 360 min respectively. With the increasing of energy input, the intensity of diffraction peaks of dolomite and hematite gradually decreased. Furthermore, the previous phase almost disappeared eventually under any experimental conditions. In addition, Fourier transform infrared spectroscopy indicates that organic matter and carbonate decompose easier than other phases, especially under stirring wet milling.

Jan 1, 2016

By R. Padilla, M. C. Ruiz

Arsenic, antimony and bismuth are commonly found in copper concentrates usually as the minerals enargite, stibnite and bismuthinite, respectively. Concentrates having high levels of arsenic and antimony must be pretreated before smelting. Roasting is the preferred method for removing these toxic impurities from concentrates; However, the removal of As, Sb and Bi in oxidizing roasting by volatilization may not be complete due to the slow reaction rates at 500- 700 °C. Oxidizing/volatilization data were obtained from pure mineral mixtures and from arsenic rich copper concentrate. The reaction mechanism for the volatilization of arsenic and antimony were discussed. Near 100% As and over 95% Sb volatilized in the oxidation of a mixture of pure minerals at 700 °C, 1% oxygen, while over 95% As, and 35% Sb volatilized at 600 °C in 1% oxygen atmosphere when using a copper concentrate containing 3.51% As, 0.14% Sb, and 0.01% Bi. Bismuth did not volatilize.

Jan 1, 2015

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By S. Redik, C. Wenzl, D. Gregurek, A. Spanring

Zinc is a component of many input materials used in various pyrometallurgical processes, for example primary lead and zinc production from Pb/Zn ores and recycling processes dealing with zinc-containing residues (e.g., copper recycling, WAELZ process). Hence, zinc and its compounds are present in the respective metallurgical vessels and interact with the refractory lining. In the present work the zinc attack on the refractories out of various primary and secondary furnaces is briefly introduced and discussed. At the prevailing processing temperatures in the metallurgical vessels, zinc oxide is highly corrosive for the brick components. The knowledge of the wear behavior is based not only on a detailed chemical and mineralogical characterization carried out on provided post mortem samples, but also on FactSage calculations. This together with results obtained by practical testing in the RHI pilot plant represents an important prerequisite for product development and brick selection for the individual customer application.

Jan 1, 2016

By Yingtao Zhang, Shaofeng Du, Yiming Rong, Wenjun Zhao, Gang Wang

"20Cr2Ni4A steel is a kind of high quality steel mainly used for manufacturing high-duty gears in the world. The high-duty gear with good performance must have wear and fatigue resistance properties. In order to get the good properties, the high-duty gear needs a high hardness gear surface and a good hardness gradient along the depth direction. In this paper, the samples were designed and a vacuum carbonitriding process was put forward to improve the surface hardness of parts for 20Cr2Ni4A. The process contained carbonitriding, quenching, cryogenics, and tempering process. The surface hardness and hardness gradient of carbonitrided samples were measured and the good microstructure was gained. The surface hardness is 67.SHRC and the case depth is 1.2mm.IntroductionSteels are widely used in industry, but the fatigue strength and the wear resistance of steel is much low. So the heat treatment process is put forward to improve the mechanical properties of steel. It can be improved by high-energy heat treatment methods for medium-carbon and highcarbon steel. Those methods will not alter the chemistry of the base metal [ 1].For low-carbon steels, carburizing and quenching should be used to improve the steels' mechanical properties, especially the surface properties. Compared with the carburizing, carbonitriding has more advantages, such as a short production cycle, low temperature and small deformation of parts. Carbonitriding is a modified form of gas carburizing, rather than a form of nitriding. The modification consists of introducing ammonia into the gas carburizing atmosphere to add nitrogen to the carburized case as it is being produced. Nascent nitrogen forms at the work surface by the dissociation of ammonia in the furnace atmosphere; the nitrogen diffuses into the steel simultaneously with carbon. Typically, carbonitriding is carried out at a lower temperature and for a shorter time than is gas carburizing, producing a shallower case than is usual in production carburizing [2]. As a material surface strengthening technology, carbonitriding has been widely used in the production [3]. And vacuum carbonitriding process is better than carbonitriding, because the vacuum carbonitriding temperature can be higher than carbonitriding without surface oxidation."

Jan 1, 2014

By Juergen Antrekowitsch, Stephan R. Steinacker

The main aim of the electric furnace treatment in the primary copper industry is the reduction of valuable metals such as zinc, lead or copper itself. On the one hand legal restrictions for the further use of the treated slag are constantly getting stricter while on the other every type of loss in the oxidic phase leads to economic disadvantages. In order to fully understand and to improve the process, kinetics during the reduction play an essential role. In the first part, this paper highlights the theoretical background of the reduction process, while the following chapters present experimental aspects and results from laboratory scale trials at the Montanuniversitaet Leoben. In addition, the comparison between the chemical reaction and the diffusion model plays a continuously important role. By investigating the reducibility of electric furnace slag, process adaptions and ameliorations are developed.

Jan 1, 2016

By Kohei Yajima

The dusts and fly ash generated from the steelmaking processes and municipal solid waste incineration processes contain metallic elements such as Fe, Zn, Pb and Cd with considerable amount of halogens. In Japan, zinc in dusts is recovered by Waelz kiln or MF process, etc. However, the presence of halogen in the dust affects the evaporation and condensation behavior of zinc and other metals, and disturbs the direct recycling of dust to steelmaking processes, because alkali or heavy metals reacted with halogen vaporize easily as halides and/or oxyhalide compounds in pyrometallurgical process. Recently, the formation mechanism of zinc oxychloride vapor was investigated and the formation of zinc oxychloride such as ZnOCl was proposed. However, considering the practical operation, the effect of water vapor on the evaporation behavior of oxychloride is not fully clarified yet. This study is focused on the investigation of evaporation behavior of ZnO with Ar- O2-HCl-H2O atmosphere.

Jan 1, 2008

By Leonid N. Shekhter, Corby G. Anderson, Esra Cankaya-Yalcin, Daniel G. Gribbin, Joseph D. Lessard, Larry F. McHugh

"A new process for smelting copper, Looping Sulfide Oxidation™ (LSO™) significantly and positively alters the smelting energy balance. This process uses copper oxide in conjunction with air for the desulfurization of copper and chalcopyrite concentrates. Copper oxide is regenerated in a flash type furnace and then ""looped"" back for the oxidation of the copper concentrate. Heat and material balances show that the Looping Sulfide Oxidation™ process requires significantly lower net energy than conventional technology. This process produces anode copper and higher S02 content off-gases for efficient formation of sulfuric acid. Additionally, the process yields slags with lower copper solubility as compared to the conventional technology.IntroductionBased on the positive results from LSO™ investigations [1], further lab investigations into co=on sulfides and metal oxides were performed. It was discovered that chalcopyrite (CuFeS2) is oxidized with copper (II) oxide. In this reaction over 98.5% of sulfur was removed as S02, while a significantly improved energy balance was observed. This paper intends to analyze both the conventional flash smelting process and the newly developed Looping Sulfide Oxidation™ process, comparing heat and material balance results. LSO™ yields improvements to the energy footprint for copper, opening the door to new copper processing opportunities."

Jan 1, 2013

By N. V. Gorelikova

A new type of zirconium mineralization has been recognized in the Devonian volcanic rocks from an orogenic depression in the Central Kazakhstan. The most characteristic features of this deposit are the fine-grained nature of the zirconium mineralization, an unusual texture of the zirconium ores, and a close association of zirconium with phosphorus in the ores. Zircon grains form fine globular aggregates with the features of hexagonal crystal habit. In addition to crystalline zircon, the ores contain metacolloidal zircon, similar to hydrozircon. The morphological and textural features of the zirconium ores suggest that the deposition of ore deposits took place at a low temperature from colloidal solutions. It is believed that this deposit should be considered to be a new type of zirconium mineralization that is related to low-temperature hydrothermal processes.

Jan 1, 1995

By Chi-Ming Chang

Alloy powders are commonly used in the purification of zinc sulfate solutions for use in standard electrowinning practice. The primary goal of this research was to study the use of zinc-lead alloys for similar reactions in the galvanic stripping of impurities from organic solutions. The effects of various parameters on the electrochemical behavior of commercially produced zinc-lead alloy powders were determined. A qualitative evaluation and summary of the influence of the more pertinent parameters on iron removal from di-(2-ethylhexyl) phosphoric acid (D2EHPA) by galvanic stripping is given. Water concentration, oxygen content and reaction temperature were the principal factors affecting the reaction rate and process efficiency. Activation energies were also calculated and indicated that the reaction changes from chemical to diffusion control .with increasing temperature in the range of 35" to 45°C. The results showed that zinc-lead alloy gave faster reaction rates with less sensitivity to process variables than SHG zinc as a reducing agent for galvanic stripping. The role of lead could be as cathodic sites for the reaction which enhances the zinc dissolution or anodic half reaction. The morphology of the zinc-lead alloy surfaces, before and after the reactions, supports this assumption.

Jan 1, 1998

By Jincheng Hu, Honggang Zhong, Qijie Zhai, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of cooling intensity on the solidification structure and ferrite phase content of a new duplex stainless steel (DSS) was investigated by using a thermal simulation setup for continuous casting. The results showed that the characteristics of the solidification structure were similar to their industrial scale manufactured slabs, including chill zone, colunmar zone and equiaxed zone. And austenite morphologies were mainly primary and secondary Widmanstatten sideplates as well as intragranular Widmanstatten plates. In addition, it revealed that the ferrite content increased with an increasing distance from the chill surface and decreased at colunmar to equiaxed transition (CET) position, then the value remained relatively stable at equiaxed zone. Furthermore, the ferrite content presented the same trend with the cooling intensity ranging from 100 mL/min to 2000 mL/min with the values just varying in a slight range.IntroductionThe duplex stainless steel (DSS) is the kind of steel that ferrite phase and austenite phase occupy about 50% respectively, or the content of the fewer phase has to be more than 30% [l]. The success of modem duplex stainless steels is to a large degree due to their higher strength than austenitic stainless steels, higher toughness than ferritic stainless steels, good weldability and high resistance to stress corrosion cracking as well [2,3]. The cost of stainless steel production continues to soar in recent years due to the increasingly higher price of Cr. In order to decrease the production cost, a new type of duplex stainless steel was developed by Bao steel [4]. This newly developed duplex stainless steel had low Cr content compared with 2205 DSS, and was expected to be applied into automobile industry. However, this type of steel was still in the initial stage of development, and the influence of continuous casting process on its solidification process and structure was still unclear, which needed to be studied further. Several works published in literature presented the effect of continuous casting conditions on duplex stainless steel (DSS) 2205, 2304 [5,6]. It was discussed that the cooling intensity in the chill-side had little efficient influence on the phase transformation. In this paper, the effect of cooling intensity on the solidification structure and ferrite volume fraction of this DSS at a given cooling rate was investigated."

Jan 1, 2014

By L. Katgerman, R. Van Toi, H. E. A. Van den Akker

"Mould filling simulations are powerful tools for optimizing the characteristics of castings. The robustness of calculational methods for mould filling simulations is generally tested in simple geometries. While a vertical plate has been used often for validation studies, this paper aims at mould filling simulations of a horizontal thin wall casting. Such castings exhibit a strong interaction between heat transfer (solidification), surface tension and gravitational force.The results are presented of a study to validate numerical simulations of mould filling phenomena in a thin wall horizontal casting. Solidification during mould filling is studied computationally. Velocities are measured using Particle Image Velocimetry.INTRODUCTIONIn foundry practice Computational Fluid Dynamics (CFD) is being considered a promising tool to arrive at a better understanding of casting defects introduced during the mould filling period of a casting. The use of CFD is believed to be advantageous in predicting possible defect locations, pouring times, and the lowest possible casting temperature without the risk of cold shuts. In addition, CFD may be used to optimize pouring system geometries [1,2]. As opposed to experimental studies in, e.g., cold water models, CFD allows for the flexible modification of the casting geometry and the pouring system, and for the inclusion of physical effects such as solidification and heat transfer. Thus, a proper use of CFD may lead to a reduction of the casting rejection rate without expensive trial-and-error procedures, and to a decrease of production costs in foundries. Mould filling simulations take a special place in CFD, because a free surface tracking algorithm is required. Over the past decade methods, MAC [3] and SOLAVOF [4], have been extended to 3-D. The robustness of computational methods for mould filling simulations is generally tested in simple geometries [5,6]. While a vertical plate has been used often for validation studies, this paper concentrates at mould filling simulations of a horizontal thin wall casting. Thin wall horizontal castings exhibit a strong interaction between heat transfer (solidification), surfaces tension and gravitational force. The gravitational force in this setting is orthogonal to the plane of flow and has therefore no influence on the shape of the free surface in the plane of flow. Mould filling numerical methods and algorithms have been recently reviewed by Chen et al.[7]."

Jan 1, 1999

By Paykan Safe

Computational Fluid Dynamic (CFD) modeling provides a powerful tool to assist with the design of ventilation and fume control systems in smelters and other high temperature metallurgical facilities. For this paper, this tool has been used to analyze the off-gas flow patterns exiting the mouth of a Peirce-Smith converter into a water-cooled hood and drop out box. The effects of various process and physical plant design parameters on process gas and fume capture and potential build up on the converter hoods was examined, and the optimum design and operating parameters were determined.

Jan 1, 2000

By Luis Hoyos-Reyes, Jesus Gonzalez-Trejo, Adriana Cervantes-Clemente, Marco Gutierrez-Villegas, Manuel Palomar-Pardave, Cesar Real-Ramirez

Recent improvements on Peirce-Smith Converters (PSC) have combined numerical and physical simulations. However, most of the physical simulations have been carried out in cold-water models with only one tuyere. Several authors have proved that 2D numerical simulations do not reproduce the hydrodynamic behavior observed in physical simulations. On the other hand, most of the 3D numerical models have used a PSC thin slice with only one tuyere, but symmetric boundary conditions on the virtual walls have been imposed in order to reproduce the behavior of the whole converter. Therefore, there is no coincidence with the rigid walls of the physical models. The aim of this work is to quantify the effect of the virtual walls boundary conditions of a PSC thin slice and to determine the minimum number of tuyeres to characterize the fluid flow behavior of the entire converter.

Jan 1, 2009

By A. Mikula, S. Karlhuber

"Unique physical and mechanical properties made the Pb-Sn solders attractive for low temperature joining of electronic parts. But since lead in solder materials has become a great enviromental problem and health concern, lead will be slowly replaced by other materials in soft solders. Some of these materials which are currently under investigation are ternary tin alloys. Many different physical properties like wetting behavior, electrical and thermal conductivity and surface tension are measured on these alloys, but on the thennodynamic properties and the phase diagram of the alloys under discussion there is only little information available. We investigated the (Ag, Au, Cu)-Sn-Zn systems and determined the thermodynamic properties over the whole composition range by emf-measurements. From these measurements we also got some information on the liquidus. In the Sn-rich corner the phase diagrams are still under investigation.IntroductionSoldering is technically defined as the joining of two base materials, mostly metals or metal coated nonmetallic substrates, with a third metal. The melting temperature of the third metal or metal alloy should be well below those of the substrates. Solder alloys can be categorized in soft and hard solders. Soft solder alloys usually contain lead, tin, bismuth, indium or cadmium and hard solders gold, zinc, aluminium or silicon. The difference between soft and hard solders is the melting temperature of the soldering material. This temperature is around 350°C.An interesting brief history of solders is given by Vianco and Frear [1]. They report, that in 4000 B.C. solders were already used in Mesopotamia. From archaeoligical evidence those solders were gold-based hard solders.Tin-lead soft solders and their use are not easily found, because in course of time tin has been reduced to stannic acid, making the identification quite difficult. Well preserved soft solder artifacts were discovered in King Tut's tomb dating from 1350 B.C. In ancient time Pb-Sn solders were used primarily for the manufacture and repair of cooking utensils and metal tools. The Romans used lead-tin solders extensively in the construction of the aqueducts."

Jan 1, 1996

By Mike Adams

A comprehensive pre-feasibility study has been conducted by Companhia Vale do Rio Doce CVRD) for Niquel do Vermelho nickel laterite deposit. Within this study, five integrated flowsheet options were evaluated via batch and pilot campaigns at Lakefield Oretest, over an intensive six-month period from receipt of ore to final reporting. Key technical objectives set by the client included demonstrating the technical viability of the beneficiation of several ore types, processing through integrated pressure acid leach/mixed hydroxide precipitation (PALIMI-IP) and mixed sulfide precipitation (PALIMSP) circuits, and the treatment of barren liquors to meet stringent environmental requirements. Refining of the MHP was by ammonia re-leach and solvent extraction (SX) to produce LME-grade nickel cathodes, NiCO3, NiO and CoS. LME grade nickel and cobalt was also produced by oxidation of the MSP and hydrogen reduction on the leachate. The database and data acquisition system, along with web-based reporting, enabled rapid turnaround on both daily and more comprehensive run reports, making it possible for speedy and confident decisions on operating conditions of the complex flowsheets. The high value of developing such data is emphasized and discussed as pivotal in the successful progression of laterite projects through to sustainable commercial viability. Keywords: Flowsheet, CVRD, Nickel, Piloting, Pressure, Leach, Refining.

Jan 1, 2004

By Thomas M. Harris

Cation exchange is not sufficiently selective to be used for the removal of heavy metal ions from a general industrial wastewater. However, if the metals can be converted to polyvalent anions through complexation, they may be removed both selectively and efficiently by anion exchange. This approach, referred to as chelation-assisted anion exchange (CAAE), has been examined using industrial wastewater samples contaminated with Ni2+ and Cr3+. For this particular application, the Ni2+ is complexed with 8-hydroxyquinoline-5-sulfonic acid, and the Cr3+ with sulfosalicylic acid. Removal efficiencies and adsorption isotherms for both the complexants and the complexes were determined in batch-mode tests.

Jan 1, 1994

By F. Shen

Qualitative and quantitative results obtained during the physical modeling of the molten aluminum flow in a tundish using an aqueous system are presented. Surface tuft, free-surface powder and laser sheet visualization techniques were utilized for qualitative studies, whereas laser Doppler velocimetry was used to elucidate the 3-D flow regimes quantitatively. The results of the study are used for validation of the CFD codes, and to explore the effect of the alterations below the nozzle in order to: (1) decrease turbulence levels, and (2) collect the inclusions. Near the nozzle, the interaction of the impinging jet and the inclined walls gives rise to vortex structures. Downstream of the nozzle, two counter-rotating secondary cells diminish in strength. As flow turns through the bend, a separation region is created. The flow heading into the closed duct is seen to be nonsymmetric. A video tape highlighting the major findings is presented.

Jan 1, 1993

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

By Akihide Nagao

The behavior of impurity hydrogen that is contained in starting material or picked up during processing has been little investigated up to now. The hydrogen microprint technique is applied to determine the microscopic location of impurity hydrogen during deformation in aluminum without hydrogen charging. Three kinds of pure aluminum of 99.99% are prepared, in which hydrogen content is varied by changing the atmosphere when they are melted and heat-treated. After rolling, tensile specimens with a gage size of 4 x 4 rnm and 0.5 mm in thickness are stamped out from these three kinds of aluminum sheets. These specimens are covered with a liquid nuclear emulsion of silver bromide crystals, stretched by 5,10 and 15 percent plastic strain or fractured, developed and fixed. SEM micrographs reveal a number of silver particles on the slip lines and on the grain boundaries. Also shown is that the more hydrogen present in the specimen, the more silver grains appear on the slip limes and on the grain boundaries. Consequently, it is concluded that impurity hydrogen is transported to the surface with gliding dislocations during deformation.

Jan 1, 1998