Search Documents

By Henrique Ventura Oliveira

Continuous casting is the most important process for solidification of steels. In this process, the fluid flow pattern in the tundish and in the mould have significant effect on the product quality. Problems associated to fluid flow in the tundish include surface turbulence, ?short-circuits?, formation of dead zones and vortexing. During grade changes, mixing in the tundish plays a significant role in determining the length of the intermixed slab. All these flow aspects can be studied by means of mathematical and physical models. In the last years, numerical simulation of fluid flow has become a very popular tool in the analysis of the performance of continuous casting tundishes. In setting-up these numerical simulations, special care should be taken in choosing the appropriate mesh distribution, the interpolation scheme, the adequate location of the inlet boundary and the turbulence model. In the present paper, turbulent fluid flow in different configurations of tundishes was simulated. Different turbulence models were used in the simulations. Residence time distribution (RTD) and mixing curves during grade changes were predicted and compared to results obtained in physical models. The performances of the different turbulence models were evaluated. For the tundishes that have been studied, the performances of the different turbulence models tested in the present work were similar. There is no evidence that any of the models provided sustained improvement when compared to the well-established standard k- model. All turbulence models tested presented limitations in simulating flows under low turbulent Reynolds numbers.

Jan 1, 2006

By S. Yokoya

With increasing requirement of steel productivity and quality in continuous casting in the conventional casting system using an immersion nozzle, it is very difficult to establish a reasonable molten flow pattern. In order to overcome this difficulty, we propose a new method of imparting swirling motion onto the flow in the immersion nozzle and to control the flow pattern in the mold. Following results have been obtained during the studies. For the case of slab continuous casting mold: High amplitudes of oscillation with a period of 10 to 15 seconds are observed in the outlet flow of the immersion nozzle and meniscus flow in the conventional casting system, while these phenomena are remarkably suppressed using swirling motion in the immersion nozzle, which leads to very calm and uniform flow pattern at the outlets of the immersion nozzle, in the mold and on the meniscus in the mold; For the case of billet continuous casting mold: (1) heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl, and (2) Quite different mold flow patterns are observed between the divergent and straight immersion nozzles. Heat and mass transport in the mold using the divergent nozzle is much more reasonable compared to that of straight nozzle. The findings, mentioned above, are very useful to control the flow pattern in the slab, and billet continuous casters. Such effectiveness of swirling flow in the SEN on the mold flow has been put into practical use. As a result, remarkable progress on the quality and production of continuous casting products has been observed in practical application.

Jan 1, 2006

By J. F. White

An experimental study was undertaken to evaluate the feasibility of a selective chloridizing roasting pre?treatment process for the elimination of impurities from zinc feed?stocks prior to recovering zinc by conventional unit operations. In this investigation, a number of chemistries that might serve as a basis for such a pre? treatment process were examined. A variety of chloridizing agents were admixed with EAF dust to promote the selective removal of lead and cadmium by the formation of volatile metal chlorides, he results of the experimentation firmly establish that selective chloridizing roasting is a technically feasible means of eliminating lead and cadmium from EAF dust. Excellent extraction efficiencies were accomplished with a number of chloride additives; as high as 98 percent lead extraction and 88 percent cadmium extraction were attained with minimal zinc losses, Continuous pilot?scale tests reinforced the trends established by laboratory?scale experimentation, Attempts of chlorine elimination using pyrohydrolysis were less successful. The extent of chlorine elimination was found to be highly dependent upon EAF dust sample type and treatment temperature.

Jan 1, 1996

By Vadym Drozd, Yongzhou Sun, Shah Najiba, Jiuhua Chen, Andriy Durygin

"Phase transitions of the potential hydrogen storage compound, ammonia borane (NH3.BH3), was investigated using Raman spectroscopy and a diamond anvil cell at high pressures up to 9.5 GPa and low temperatures down to 90K. At room temperature, ammonia borane has three phase transitions in this pressure range. Upon cooling, four new phases were discovered through changes in characteristic Raman spectra. This result provides information about the stability of new bonding characteristics of this potential hydrogen storage material at low temperature and high pressure region.IntroductionDevelopment of hydrogen technology requires the safe, efficient and environmental friendly materials for hydrogen storage and hydrides have attracted much attention as hydrogen storage media. Among chemical hydrides, ammonia borane (BH3NH3) stands out due to its high gravimetric and volumetric hydrogen density ' "". Despite high hydrogen content, this compound is very stable. It releases hydrogen in several steps by thermal decomposition in the temperature range of 100°C to 500°C. Direct thermal decomposition also causes toxic borazine emission. Recent research interests on ammonia borane include destabilizing this compound to lower the dehydrogenation temperature with an enhanced hydrogen release rate using different techniques, e.g. the nanoscaffolds'', ionic liquids"" and acid'"" or transition metal catalysts' ""'. As a molecule of ammonia borane consists of protonic (NH) and hydritic (BH) hydrogens bonded by the polarized dative bond, thermal or catalyzed decomposition requires breaking of N-H and B-H bonding. Still now, the detailed information about the bonding characteristics of ammonia borane is not sufficient to understand details about its phases and structures. The development of methods to enhance hydrogen discharge rate from ammonia borane requires a detailed study about the structural and dynamical properties that control the stability and the intermolecular interactions of this material. This study is motivated to investigate the stability of the existing phases and also to explore the existence of any new phases at different temperatures and pressures which may have enhanced hydrogen release and uptake properties."

Jan 1, 2012

By A. V. Tarasov

In the course of research aimed at improving the performance of the Vanyukov smelting process (VP) for treating sulfur raw materials in a pilot-scale furnace it has been found that an increase in the calcium oxide content up to 12% to 14% in case of smelting to produce high-grade matte results in a decrease in the copper content of slag by 0.05% to 0.3%. The residual copper content of slag can be computed by a formula taking into account an increase in the calcium oxide content of the feed material and that in the slag. In the course of research for improving the performance of the zinc-containing slag fuming process with blowing of the slag bath with combustion products of natural gas it has been found that the silica and calcium oxide contents have an effect on the degree of zinc sublimation. In case of slag containing 24.4% SiO₂ and 6.95% CaO by weight (SiO₂:CaO = 3.51), the residual zinc content of slag was 3.25%. The minimum residual zinc content of 1.95% was obtained in case of slag containing 22.5% SiO₂ and 14.5% CaO by weight (SiO₂:CaO = 1.55). An increase in the CaO content of slag up to 16% by weight with a ratio of SiO₂:CaO = 1.25 to 1.35 permits minimization of zinc losses in slag by achieving a residual zinc content of final slag in the order of 1%.

Jan 1, 2006

By M. I. Kalashnikova

The leaching of metal nickel in copper sulfate solutions is investigated. It is established, that irre-spective of presence or absence of chloride-ion and oxidizer (oxygen) in system process can be divided into three stages, characterizing by restoration and oxidation of metals with formation of metal copper and cuprite and differing in the speeds of sedimentation of copper and transition of nickel into solution. At the initial stage of process along with allocation of metal copper it is be-sieged cuprite, that results in excess of speed of sedimentation of copper in comparison with dis-solution of nickel. At the second stage speed of transition of nickel into solution falls practically to zero, and sedimentation of copper proceeds on reaction of interaction of metal copper with copper sulfate solutions with cuprite formation. During the final period speed of transition of nickel into solution exceeds speed of sedimentation of copper due to course of reaction of resto-ration of cuprite up to metal. Influence of an ion of chloride and oxidizer on formation of various phases is revealed. It is established, that presence of an oxidizer results in increase in a share of cuprite in a deposit. With increase of the maintenance of chloride-ion speed of metal copper allo-cation essentially grows even at presence of an oxidizer in system.

Jan 1, 2006

By N. Panagiotopoulos

A low-grade (1.06% Ni, 0.06% Co) hematitic type lateritic ore from Triada, Euboea Island, Greece, has been leached with sulfuric acid at atmospheric pressure for the extraction of the contained Ni and Co values. The effect of various parameters, including reaction time and leaching temperature, acid strength, pulp density, etc., on Ni, Co extraction and Fe dissolution was determined. By leaching at 95°C for 4h with a 3N sulfuric acid solution at 25% pulp density, Ni and Co extractions were 82 and 75% respectively, and Fe co-dissolution 28%, yielding a pregnant solution containing 2.7 g/l Ni, 0.16 g/l Co, and 33 g/l Fe. Overall acid consumption was 850 kg/t ore (or 100 kg/kg Nil. Preheating of the laterites at 600°C before leaching resulted in much faster leaching kinetics for Ni, but the final extraction and acid consumption remained unaffected; Fe extraction was not influenced. Three-stage counter-current leaching at 9S°C, using 2N acid strength at each stage and 35% pulp density, reduced acid consumption to 350 kg/t ore (41 kg/kg Nil, and yielded 81% Ni recovery. Percolation leaching of -10 mm laterite at ambient temperature with 3N acid for 7 days resulted in 58% Ni extraction.

Jan 1, 1988

By S. N. Ojha, Gouthama, R. K. Mandal

"Spray deposition processing of liquid immiscible alloys, based on AI-Pb and Cu-Pb systems have been investigated. Process variables have been optimized to generate uniform dispersion of ultrafine second phase particles in· the matrix of the primary phase. Mechanisms governing the microstructural evolution in this synthesis methodology are discussed. Results of the present investigation are used to demonstrate that rapid solidification of atomized droplets initially provides a high nucleation rate of the second phase during the liquid phase separation. The solid matrix phase nucleates at a later stage and grows with a high velocity enabling trapping of the dispersed phase. Subsequent alteration in the size and size distribution of the second phase is suggested to arise further during deposition of high velocity droplets. Possible reasons for this effect are brought out. Microstructural features of atomized powders and spray-deposits of these alloys are presented to support the present approach of synthesizing composites. IntroductionIn recent years, synthesis of advanced materials with metastable microstructures and ultra fine dispersion of second phase particles has led to the development of novel techniques of materials processing. The other requirement of such a processing methodology is to achieve near-net shape geometries in less number of processing steps. The solidification processing method via spray deposition route qualifies these criteria. This process primarily involves atomization of a melt by high energy gas jets into spray of droplets which are subsequently propelled by the kinetic energy of the gas towards a deposition substrate to build-up a thick high density preform. Although the concept of spray deposition was pioneered by Singer [1] in the early seventies, the fundamentals of the deposition process has been understood only recently [2-4]. Several benefits of spray deposition processing are by now well established [5,6]. Rapid solidification effects are inherent in spray deposition processing due to high heat exchange rate at the droplet-gas interface and also on the deposition surface by force convection. Since considerable heat extraction occurs from the atomized spray prior to droplet consolidation, a relatively low processing temperature is ensured in this process. As a result deleterious coarsening phenomenon can be minimized. In addition, controlled maneuvering of the substrate provides the capability of the process in producing disc, sheet or tube shape preforms of difficult to work materials in a single operation. A significant improvement in properties, resulting from microstructural homogeneity and refinement in grain size induced by spray deposition has been reported for several alloy systems [7,8]."

Jan 1, 1994

A strategy is presented for a relatively. "low-tech" means for decontamination of streams . containing .low concentrations of toxic metals. Metal ion solutions were . circulate through fluidized beds of activated carbon which support bio-films ?of bacteria .that naturally excrete exopolysaccharides. The attached 'biomass is shown to significantly enhance nickel, cadmium and silver extraction from dilute solutions (5- l00mg/l). By heat treating (at 300º C) the metal/biomass/carbon particles, bio-sorbed silver was subsequently fixed to the carbon surface. This approach to metal decontamination may therefore also provide a route for dispersing and fixing catalytic metal particles over an activated carbon surface.

Jan 1, 1991

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By M. S. Moats

Galvanic stripping, in conjunction with solvent extraction, has been proposed as a technical option to the challenging problem of iron removal in certain hydrometallurgical processes. The galvanic stripping process is based on the ability of a solid metal to directly reduce ferric ion to the ferrous state in an organic media. Stripping the iron into the aqueous phase is then easily accomplished. Previous work has shown the reaction kinetics and efficiency are affected by such operating parameters as water and oxygen contents, temperature, time and metal reductant. In this study, the optimum operating range for some of these variables was determined. Both zinc and iron metal were used in the separate stripping of iron from D2EHP A. Reasons for the differences in the extent of the reaction obtained using the various conditions are discussed.

Jan 1, 1996

By Shadia J. Ikhmayies

CdSxTe1-x and CdS1-yTey solid solutions are usually formed in the interfacial region in the CdS/CdT thin film solar cells during the deposition of the CdTe layer and/or the processing steps of the device. It is well known that CdCl2 heat treatment encourages the formation of the CdSxTe1-x alloy which improves the solar cell performance. In this work, indium doped CdS1- yTey thin films are produced by first producing CdS:In thin films by the spray pyrolysis (SP) technique on glass substrates, then annealing the films in nitrogen atmosphere in the presence of elemental tellurium. The films are characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and transmittance measurements. The transmittance is used to deduce the optical parameters such as; the extinction coefficient, refractive index, besides to the real and imaginary parts of the dielectric constant. The dispersion parameters such as Eo (single-oscillator energy) and Ed (dispersive energy) of the deposited films are also estimated and discussed.

Jan 1, 2015

By M. Krishna, Jayagopal Uchi1, Shanta Sastry, B. M. Satish

"A well-considered composite of ZA-27 reinforced with weight percentage 0, 2, 4, and 6% of alwninite particulate has been made by compocasting technique. The elastic properties of ZA- 27 /alwniniute particulate composite were determined by using U1M. The results showed that the modulus of elasticity and UTS of the composite gradually increases with increase in the wt.% of reinforcement. However, the overall ductility decreased monotonically with an increase in reinforcement. The results of these tests· as well as the predictions of several model~ for composite strengthening available in the literature were compared with experimental results. The data observed from Young's modulus by measurements studies were compared with theoretical results predicted by Eshelby model.IntroductionMetal matrix composites (MMCs) have received increasing attention in _the recent decades as engineering materials. The introduction of a ceramic reinforcement into a metal matrix produces a composite material resulting in an attractive combination of physical and mechanical properties that cannot be obtained with monolithic alloys. Particulate reinf9rced MMCs among the discontinuously reinforced MMCs have attracted quite a lot of attention both in the industrial sectors and the academic communities. There is an increasing need for knowledge about the processing techniques and mechanical behavior of particulate MMCs in view of their production getting enhanced and their commercial applications becoming wider [I]. Interest in particulate reinforced MMCs is mainly due to easy availability of particles and economical processing techniqu"

Jan 1, 2000

By Donald P. Ziegler, James F. Klausner, Srinivas S. Garimella

"By 2015, nearly half the world's population will live in ""water stressed"" areas. Production of fresh water utilizing waste heat from industrial processes has been identified globally as a research priority.About 15% of the electricity required to produce aluminum is lost as waste heat in the off-gas. However, the low temperature (low grade) of the heat limits reuse. The off-gases contain 50-150 ppm SO2 ; tightening regulations coupled with increasing coke sulfur levels are motivating SO2 control, for which seawater scrubbing is attractive for smelters with suitable access.We describe a process that produces fresh water, utilizing the waste heat while scrubbing SO2 . It uses direct contact between seawater and off-gas to humidify the off-gas. The vapor is subsequently condensed. In smelter trials, a unit treating a slip stream produced high quality water in the anticipated quantity, attaining over 95% SO2 scrubbing. Future work involves scaling the process to be economically attractive.BackgroundPopulation growth, coupled with industrialization and urbanization, are increasing demand for water. Water scarcity already affects every continent. Around 1.2 billion people, or almost one-fifth of the world's population, live in areas of water scarcity, and 500 million people are approaching this situation. By 2025, 1.8 billion people will be living in countries or regions with absolute water scarcity, and two-thirds of the world's population could be living under water stressed conditions (< 1,700 m3 per person annually) [1]. An assessment by the U.S. General Accounting Office revealed that under normal conditions, by 2013, water managers in 36 states in the USA anticipate water shortages, and that the number might grow to 46 states under drought conditions [2].The obvious choice to alleviate water scarcity is the 97% of available water in the oceans, which is saline and requires desalination for use in biological, agricultural and industrial applications. Technologies developed for desalination include Thermal Distillation, Reverse Osmosis (RO), Electro-Dialysis, and Vacuum Freezing. Distillation and RO are the most commercially prominent. Thermal distillation technologies include Multiple Effect Distillation (MED) and Multi-Stage Flashing (MSF). The report commissioned by the World Bank [3] is one of the many excellent references on desalination technologies. According to the International Desalination Association working paper [4], there were more than 17,348 industrial scale desalination plants installed or contracted by 2004. The total production from these plants is on the order of 8.3 billion imperial gallons per day. RO provides 47.2% of the total capacity. The leading thermal process, MSF, provides 36.5% of the total capacity. Although MSF and RO technologies currently provide the most cost effective means for desalination, their drawback is that they are very energy intensive, and whether or not they remain cost effective strongly depends on energy prices and energy supply."

Jan 1, 2012

By T. Mutoh

Tellurium in raw slime has recently been recovered as copper telluride in Onahama Smelter & Refinery. The slime is decopperized with sulfuric acid solution in conventional leaching tanks. The pregnant leach solution containing 45 g/l of copper and 1 g/l of tellurium is introduced to a copper telluride recovering reactor. The tail solution from the reactor containing less than 20 mg/l of tellurium is recycled directly to circulation tanks of copper electrolysis. The impurities of the product copper telluride is kept below 1% without any purification.

Jan 1, 1990

By Jin-tao Gao

In order to recover Ti resource from titanium bearing blast furnace slag, a new technology to separate perovskite phase from CaO-TiO2-SiO2-Al2O3-MgO system by supergravity is researched. In the condition of gravity coefficient of 750g, treatment temperature of 1305°C and time of 20min, the significant layers appear in samples which are obtained by means of centrifugal treatment. Along the direction of the supergravity, the volume fraction of perovskite phase increases gradually, and the equivalent diameters of perovskite phase crystals increases with the area approaching to the bottom of the sample. It is indicated that TiO2 is enriched in the bottom of sample as concentrate with a recovery ratio of 74.05% by supergravity treatment.

Jan 1, 2014

By Matthias Merzkirch, Volker Schulze, Kay Andre Weidenmann

"Unidirectionally reinforced light weight compounds based on light metals such as the aluminium alloy EN A W-6082 are adequate materials for the future use in transportation means like automobiles and airplanes. Due to the occurring cyclic loads knowledge about the crack growth behaviour of such composites is needed. The investigations at a load ratio of R = 0.18 show that the crack growth rate of the aluminium matrix is reduced if reinforced by spring steel wire with a reinforcing ratio of only about 1 Vol.-%. Additionally, the acoustic emission analysis allows detecting crack growth within the matrix material, crack propagation along the interface wire/matrix and crack closure which could also be determined with the help of a self designed capacitive displacement measuring gauge. The damage behaviour could be verified by metallographic and SEM investigations.IntroductionIn the field of lightweight structures for transportation means the need for light, strong and stiff materials, in particular composite materials, is increasing in order to save resources and costs. Lightweight materials such as aluminium and magnesium alloys are highly efficient candidates to be used in the composite extrusion process [1] which allows for a simple production of unidirectionally reinforced profiles with a large diversity of geometries at low costs. Figure 1 depicts the principle of the composite extrusion process; within the first part of the tool the billet material is split into several strands whereas the middle part of the tool allows the supply of the reinforcing elements. The third part of the tool rejoins the matrix material and the reinforcing elements and defines the final shape of the profile."

Jan 1, 2011

By Yuanbo Zhang, Qian Li, Helei Zhang, Heng Yu, Guanghui Li, Tao Jiang

"Large reserves of specularite iron ores have been found all over the world, which is characterized by high total iron grade, low gangues content, as well as low commercial price. However, it has not been widely used in sinter or pellet production due to its inferior sintering and roasting behaviors. It has shown that the proportion of specularite ores was increased as high as 40%~50% and good results was achieveed by using Composite Agglomeration Process (CAP), an innovative agglomeration process invented by Central South University. But the mineralization of specularite is still unknown during composite agglomeration processing. In this paper, the induration characteristic of specularite ore is studied by simulating CAP in laboratory, as well as microstructure analysis of CAP product. The results show that specularite pellet is mainly indurated through recrystallization of Fe2O3, calcium ferrite within high basicity sinters matrix interweaves with the recrystallized Fe2O3 on the surface of the pellet, which forms an integral microstructure, and ensures high strength of CAP product for ironmaking.IntroductionLarge reserves of specularite iron ores have been found all over the world, especially in Minas Gerais of Brazil, Xuanhua city and Anshan city of China, Elba island of Italy, St.Gotthard of Switzerland, Cumberland of Britannic, and so on. The specularite ores have a smooth surface, as well as a good crystallization and dense texture. When specularite is used to produce pellets, the specularite ore grains are difficult to adhere onto green ball due to its poor ballability. Moreover, specularite pellet requires high roasting temperature over 1300°C [1]. When specularite ore is used in sintering, the permeability of sintering bed gets bad and the quality of sinter is diminished. The practice in a few sintering plants finds that the output and strength of sinter decrease with the increase of specularite proportion, and the consumption of coke increases [2-4]. Therefore, the utilization of specularite has been limited. Composite Agglomeration Process (CAP) is an innovative technology invented by Central South University [5-7]. The process has the following merits: making reasonable utilization of different iron ore resources; improving the quality and output of sinters; manufacturing sinters with low basicity; significantly reducing energy consumption, etc[8-9]. It has been shown that large proportion specularite ores, as high as 40%~50% can be used well by CAP [10], but the mineralization of specularite pellet is still unknown during composite agglomeration processing. In this investigation, the induration characteristics of specularite ore pellets is studied by simulating CAP in laboratory, and the phase composition and microstructure of CAP product are also characterized by using microscope and Leica image analyzer (Germany, Leica DM RXp)."

Jan 1, 2011

By Keizo Uematsu, Satoshi Tanaka, Zenji Kato, Nozomu Uchida

"A novel technique is developed and applied to evaluate the binder segregated at the· surface of granule. Compressive strength of each granule was measured directly with a micro-compressive instrument. The relation between compressive characteristics and the amount of binder was discussed quantitatively.IntroductionCharacterization of granules is essential in the production of ceramics, since they govern the structure of green compact and thus the structures and properties of ceramics. However, there is no research to clarify the relation between the strength of granules and structure of granules, especially of binder segregation at granule surface. We develop a novel technique to determine the binder concentration in the granules by the iodine method. In this study, we measure yield strength of granules directly and discuss the relevance between compressive characteristics and the concentration of binder.ExperimentalGranules were prepared by spray-drying of aqueous slurry of commercial alumina (AL160-SG1. Showa Denko, Tokyo, Japan) and PVA (PVA 105 Kurare, Japan). PVA. concentration in granules was 1.1, 1.5 and 2.3 wt%. The inlet and outer air temperatures were 200 and 95 °C , respectively. Iodine-potassium iodide solution was prepared by dissolving iodine (0.15mol) and potassium iodide (0.15mol) in diluted water (50ml). A saturated boric acid solution was prepared by mixing boric acid powder with a diluted water."

Jan 1, 2000

By V. D. Tathavadkar

Natural chromite mineral is a solid solution of spinet end members namely: chromite (FeCr2O4), hercynite (FeA1204), magnetite (Fe3O4), magnesio-chromite (MgCr2O4), (MgA12O4), and magnesio-ferrite (MgFe2O4). A phase transformation in chromite minerals occurs in oxidising conditions during the soda-ash roasting reaction. This phase transformation plays an important role in improving the extraction efficiency of Cr3+ from mineral phase. The extraction efficiency of chromium (Cr3+) from chromite to a water¬soluble sodium chromate (Cr6+) salt depends upon the decomposition kinetics of the spinet phase. An investigation of the phase changes in chromite ores in the absence of sodium carbonate was carried out in air, argon, and in argon +5 % hydrogen gas mixture. The thermodynamics of phase transformation reaction in chromite solid solution phase is discussed using the solution model proposed by Sack and Ghiorso [1]. The microstructural changes and the changes in elemental compositions of different phases were examined by SEM and electron probe microanalysis (EPMA) respectively. The experimental results indicate that the solid solution spinet phase in chromite mineral undergoes spinodal decomposition under the influence of oxygen partial pressure and temperatures. The structure of phases formed and their morphologies suggest that the phase decomposition may be similar to those observed by Burkert et. a]. 121, although the scale of phase separation in chromite appears to be strongly dependent on oxygen partial pressure.

Jan 1, 2001