Search Documents

By Takafumi Kondo, Satoshi Yamashita, Noboru Masuko

"Aqueous oxidation of phosphite ions to phosphate ions with dissolved oxygen was examined at 80° C and pH 4.5 mainly from the stichiometric point of view. Dissolved oxygen alone can not oxidize sodilim phosphite in aqueous solution, but when sulfur dioxide is coexistent, cooperative oxidation for both sulfite and phosphite can occur in aqueous solution. Sulfur dioxide itself is well known as a reducing agent, but it also reacts as an oxidation-promoting agent for other species under a certain condition. So sulfur dioxide is· a promising cheap reagent for waste phosphite processing.IntroductionIn a liquid-phase oxidation reaction using the dissolved oxygen gas, the eoexistence of a copper salt is required generally. Recently, it was reported that the oxidation reaction progressed by using mixed gas of sulfur dioxide and oxygen without the copper catalysis, and the attention has been collected1·3). The present authors also noticed the phenomenon since the early time and have been studying on the reaction mechanism of sulfur dioxide in liquid phase oxidation 4l. It was found that; by using the SO2-O2 mixed gas, the oxidation of phosphite ions to phosphate ions proceeded efficiently in sulfuric acid solutions. In the present report, the applicability of SO2-O2 mixed gas as a cheap oxidizing agent to the industrial processing of the waste solution of electroless nickel· plating is investigated. It is well known that the sulfur oxide dissolved in aqueous solution is oxidized ·by the oxygen in the air to sulfuric acid according to the following equation"

Jan 1, 2000

By Natasa Mitevska

In order to ensure the minimal copper concentration in the reverb furnace slag, the graphical optimization method is used and the optimal slag composition of the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Serbia) is obtained: (Si02) .. 38.0%; (FeO) .. 40.0%; (Fe3O4) = 5.0%; (CaO) = 5.0%; (Al2O3) .. 6.0%. Keywords: Optimization, Reverb Furnace Slag, Graphical Method

Jan 1, 2003

By Afshin Sadri

Acousto Ultrasonic-Echo (AU-E) is a technique developed to provide accurate measurements of the refractory lining wear in operating smelters based on the principles of stress wave propagation. The objective of the system is to provide feedback for the continuous optimization of the overall smelter operation. In some cases, the AU-E refractory lining measurements have allowed clients to extend their smelter campaigns and operate safely for several years beyond their planned reline schedule. In other cases, AU-E results inform clients of serious issues within their furnace allowing them to shut down their smelters ahead of predicted failures and possible disasters. This paper presents the results of several smelter AU-E inspections of the hearth and sidewall. These case studies demonstrate how the AU-E results were used to positively affect the smelter operation.

By N. Kanari

Chalcopyrite concentrates and their pure constituents were chlorinated by C12+N2 between 25 °C and 750 °C. The reaction products were analyzed by SEM, XRD and chemical analysis. The effect of gas flow rate and chlorine content of the gas mixture on the reaction rate were investigated. At room temperature, these solids start to react with chlorine giving metal and sulfur chlorides. Complete reaction is achieved at about 300 °C and the iron and sulfur chlorides were fully volatilized. The chlorination residue is composed of valuable metals' chlorides. A simplified flow - sheet for the treatment of chalcopyrite concentrates by chlorine was suggested.

Jan 1, 1998

By Jim Sarvinis, Mark Berkley, David Clarry, Jason Berzansky

"Technologies developed to sequester CO2 or use CO2 for enhanced fossil fuel recovery are currently being utilized across the globe. Taxation regimes and CO2 credit trading are becoming drivers for a number of projects. Some mining companies have also identified ancillary opportunity to sequester CO2 in their by-products; recent work in the alumina industry is a prime example. In addition to process plant emissions, mining companies are becoming increasingly aware of their overall carbon footprint, including CO2 generated during the production of utility power. New power plant designs, in various stages of development, include CO2 separation and sequestration techniques. This paper summarizes the state-of-the-art for these technologies; including integrated gasification combined cycle (IGCC) power plants. A concept to use the gasification products as reductant in metallurgical processes is also described. The relevance of technology from power plant designs with post-combustion capture to the processing of off-gas generated in metallurgical facilities is also reviewed.IntroductionGlobalization and international economic growth have led to an increase in energy demand worldwide, and a corresponding increase in greenhouse gas (GHG) emissions. In 2005, 81% of global energy supply came from fossil fuels [1]; and while alternative energy technologies are emerging, it will require many decades to curb society’s fossil fuel dependence. Given the global concern of climate change and its scientific relationship with anthropogenic carbon dioxide (CO2), there is at present great interest in the development of techniques to reduce emissions of CO2. While most of these efforts are related to power generation and energy efficiency, the development of technologies for CO2 capture may offer opportunities in reducing emissions from industrial processes."

Jan 1, 2008

A modified Cuprex Metal Extraction Process (CMEP) leach process was used to extract Cu. Ni and Co from a complex sulphide concentrate. The standard leach was modified to a two-stage countercurrent leach which provided emf control of the copper SX feed and minimized iron dissolution. A flowsheet was developed to recover the base metals and silver from the leach solution and gold and platinum group metals from the leach residue which was predominantly elemental sulphur. Techniques required to maintain an iron balance in the system including pressure oxidation and solvent extraction are described.

Jan 1, 1996

By T. Wang, R. G. Reddy, D. Mantha

"A new eutectic LiN03-NaN03-KN03-KN02 quaternary molten salt system was calculated using thermodynamic modeling. The eutectic temperature was predicted to be 100°C. The melting point and heat capacity of the salt eutectic composition were determined using DSC. The experimentally determined melting point is in excellent agreement with the predicted value. The melting point is more than 124°C lower than that of the KN03-NaN03 solar salt. The density of the molten salt was experimentally determined as function of temperature. Using the density, heat capacity and the melting point, thermal energy storage density and gravimetric storage density of the quaternary molten salt were calculated and compared with that of solar salt. The larger storage density value of this molten salt indicates that this salt has a better energy storage capacity for solar power generation systems.IntroductionMolten salts have been used as thermal energy storage media for solar energy applications. Nitrates are being used in the solar energy applications for their low melting point, low unit cost, high heat capacity, high thermal stability, negligible vapor pressure and high energy storage density [l]. Solar salt (NaN03/KN03: 60/40) is the most popular thermal energy storage medium which is currently being used with the freezing point of 221 ·c [2]; another ternary system HITEC® which contains NaN03, KN03 and NaN02 has freezing point of 141°C [3]. Newer nitrate salt mixtures are being studied and projected as potential candidates for thermal energy storage (TES) and heat transfer (HT) applications. Based on these favorable features, molten salt can work directly as the energy storage medium below 500°C [l]. Development and synthesis of newer molten salt mixtures with freezing point lower than those currently used for thermal energy storage applications is necessary for sustained utilization of solar energy. The approach to develop lower freezing point molten salt mixtures is by the prediction of new eutectic mixtures and also by the development of new nitrate compounds."

Jan 1, 2012

By Vladimir Panjkovic, Ostrovski. Oieg, Campbell Cripps Clark, John Truelove

"Effects of properties of raw materials and blast on the performance of an iron bath reactor have been examined by a mathematical model. The model consists of three modules: 1) chemical reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, post-combustion ratio and heat-transfer efficiency, temperature and composition of the off-gas, and slag and metal chemistry.IntroductionOne of the anticipated advantages of smelting reduction over conventional ironmaking is the use of lower-grade raw materials. In this work, the effect of-properties of raw materials on the performance of an iron-bath reactor is examined with a numerical model. The model is also used to assess the effect of properties of the blast (flowrate, temperature and oxygen enrichment) and ejected droplets (generation rate, size and ratio of total weights of slag and iron droplets) on the key parameters of the process. In the process coal, oxygen, ore (which may be partly prereduced) and fluxes for specified slag composition are charged to the bath. Slag and iron droplets are ejected from the bath into the gas phase, where they are heated before returning to the bath. Iron droplets undergo decarburisation and reoxidation with CO2 and H2O. Dust is also generated from the bath, and oxygen or preheated air for post combustion is injected from the top of the vessel.The model consists of three modules: 1) reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The structure of the model and the data exchange between the modules are shown in Fig. 1. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, postcombustion ratio (PCR), heat transfer efficiency (HTE), off-gas temperature and composition, slag and metal chemistry, and rates of decarburisation and reoxidation of the iron droplets."

Jan 1, 1996

By T. S. Montgomery

The performance of carbon-magnesia brick in electric arc furnaces (EAF) is interpreted in light of their observed optical microstructures. Features at the bricks' hot faces were protruding periclase grains, metal globules, graphite-metal contacts and linear void patterns. These features were com-pared to similar features previously seen from microstructures of basic oxygen furnace (BOF) refractories. Modes of formation were sought; an attempt was made to interpret their influence related to wear mechanisms.

Jan 1, 1982

By Toshiyuki Kozuka

CdTe metal composite semi-conducting material has high potential in good performance of energy conversion efficiency for solar cell and there is much room for improvement of the performance by developing a process of making a thin CdTe film. In this paper, the imposition of intense magnetic field on CdTe electro-depositing surface is proposed, which is one of the possibilities for improving the energy conversion efficiency. In the experiment, cryogen-free super-conducting magnet up to 5T was used and CdTe film was deposited electrically in -o.nv vs. SHE The electrolyte was Cd and Te ammonia alkali solution with controlled temperature in the acrylic cell of 70mm diameter. Electro-deposition behavior of CdTe has affected by the imposition of the intense magnetic field due to microscopic convection in the vicinity of the depositing surface. Electro-deposited surface of CdTe becomes smooth due to microscopic convection around the surface, and the crystallization behavior is also affected, where crystallization temperature and the grain size is changed by the imposition of intense magnetic field.

Jan 1, 2003

By Batric Pesic

Dissolution of gold with elemental bromine was studied by using a rotating disc technique. The main parameters studied were: bromine concentration, stirring speed, pH, and temperature. Additionally, effect of copper, iron, and manganese was also examined. A special attention was paid to elucidate the role of cations, primarily Na+, during gold dissolution. It was found that gold dissolution with bromine was characterized with two pH regions. Below pH=7, gold dissolution was independent of pH, and above this value, gold dissolution decreased with pH increase. Gold dissolution rates were proportional with concentration of bromine. Two regions, diffusional and kinetic, were observed with respect to stirring speed. with respect to the role of Na+, and cations in general, they play absolutely no role during gold dissolution with bromine, unless they are in their lower oxidation state and become oxidized by bromine. In that case they have a negative effect because of bromine consumption.

Jan 1, 1991

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The disposal of wastes is a serious environmental problem, since available landfill space is dwindling. Their treatment by pyrolysis or combustion has merit, and the corresponding fuel or power production is of technological interest. However, such processes need a rigid control of emissions. This work addresses the gaseous light hydrocarbons (LHCs) generated during sequential pyrolysis and partial oxidation of unserviceable tires, PET bottles, com wastes (DDGS) and sugarcane bagasse in a two-stage laminar-flow horizontal furnace, kept at 1000 °C. Gas chromatography was used to identify and quantify the components of the emitted gaseous light hydrocarbons. The results showed that the biomass residues generated the highest emissions of aliphatic hydrocarbons, whereas PET generated the most aromatic hydrocarbons. When stainless steel meshes were inserted in the exhaust flow, it was found that hydrocarbon emissions were curtailed; as such meshes catalyzed partial conversion of these carbon-bearing gases to carbonaceous nanomaterials.IntroductionLight hydrocarbons (LHCs) are volatile organic compounds, consisting of hydrogen and carbon with low molecular weight; the most common species are methane, ethane, propane, butane, etc. LHCs are valuable since they are a very important energy resource. However, uncontrolled release of light hydrocarbon gases to the atmosphere should be avoided [l, 2]. In this work, a development is presented for the evaluation of LHCs generated during the controlled pyrolysis/combustion of several wastes in a two-stage laminar-flow horizontal furnace. Samples of unserviceable tires, post-consumer PET bottles and waste residues from the bioethanol industry (DDGS and sugarcane bagasse) were burned. A catalyst system, consisting of stainless steel screens, was tested for its effects on the gaseous emissions."

Jan 1, 2011

By Peng Lv, Shiqian Liu, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

The treatment process of a low-grade refractory gold ore containing sulfide minerals and carbonaceous matters was studied in this work. The gold extraction of this ore by all-sliming cyanidation was only 11.75%. Hence, a pretreatment was necessary. In this paper, a flotation-preoxidation-cyanide leaching process was developed. The concentrate from the flotation procedure was processed using different preoxidation methods. A concentrate containing 34.08g/t of gold with the gold recovery ratio of 81.20% was obtained by flotation. After roasting, microwave heating or alkaline pressure oxidation, the gold cyanidation ratio reached 82.37%, 81.26% and 71.09% respectively. Roasting was an effective, reliable and mature technique to oxidize sulfide minerals and carbonaceous matters. Roasting and microwave heating both produced dangerous environmental pollutants while alkaline pressure oxidation was eco-friendly.

Jan 1, 2015

By Dinabandhu Ghosh

The stability diagram of the ternary system Ti-C-O is drawn in the present work for four temperatures, 1473 K, 1573 K, 1673 K and 1873 K, showing the stability fields of TiC, Ti, TiO, Ti2O3 and TiO2. An analysis of the system reveals that it is not possible to produce Ti in a carbon-saturated system; instead, the stable product is TiC. However, Ti can be an equilibrium product in a carbon-unsaturated system at prohibitively low values of pCO and pCO2; for example, at 1873 K, these limiting values are: pCO = 10-6.76 atm and pCO2 = 10-13.36 atm, which, when exceeded, produce TiC and TiO respectively. The magnesiothermic reduction is examined through the stability diagram (log pO2 vs. 1/T) of the system Ti-Mg-O, drawn for a number of pMg values, presenting the pairwise stability fields such as Mg(l) + Ti(s), Mg(v) + Ti(s), MgO(s) + Ti(s), etc. The diagram shows that magnesium reduction of TiO to Ti is possible only at T < 1641 K with pMg = 1 atm and only at T < 1569 K with pMg = 0.5 atm. An experimental scheme for Mg vapor reduction of TiO2 is proposed in which an argon stream is passed over a Mg(liquid) evaporator at temperature T1 (say, 1234 K); the resulting Ar-Mg mixture at 1 atm is subsequently flown over a bed of TiO2 at temperature T2. A thermodynamic analysis establishes that complete reduction to Ti is possible and that the best results are obtained when T1 = T2.

Jan 1, 2006

By Elias Rigopoulos

In the present study the reductive behavior of dust from the rotary kilns (RK), in ferronickel production from nickeliferous Greek laterites, is investigated. The study concerns dust of various origins (washing towers, electrostatic filters, polycyclones) and pellets made from the dust. Reducibility was studied in the temperature range of 700 °C to 850 °C in a laboratory tube furnace. Experimental results showed that reduction degree increases with temperature up to about 800 °C. The rate of reduction is great during the first minutes, giving a reduction degree R% equal to about 25%, in only a few minutes. After this, the rate is decreasing until it diminishes to zero after about 10-20 minutes of reaction. Maximum reduction degree achieved is 26 to 28%. Rates and reduction degrees at various temperatures are higher for the dust samples than those of the respective pellet samples. Keywords: Ferronickel, metallurgy, laterites, pellets, reduction

Jan 1, 2004

By P. N. Anyalebechi

The effects of Si (0.19-0.52 wI. %), Fe (0.20 wI. %-0.44 wI. %), and Cr (0-0.10 wI.%) on the response of ingots of aluminum alloy 3004 solidified at different rates (O.IO°C/s to 30°C/s), to homogenization heat treatment have been investigated. Response to homogenization was determined by quantifying the following microstructural parameters: (i) amount of Mn retained in solid solution; (ii) types, relative amounts, sizes, size distributions, shapes, and chemical compositions of second phases; (iii) extent of the alpha-transformation (i.e., AI6(Fe,Mn) --7 (XAI12( Fe,MnhSi) reaction; (iv) dispersoid formation; and (v) alleviation of dendritic microsegregation. Of the three alloying elements investigated, Si had the greatest effect on the response of aluminum alloy 3004 to heat treatment. Increase in Si content, fineness of cast microstructure, and homogenization temperature facilitated alpha-transformation reaction, dissolution of Mg2Si, loss of Mn supersaturation, and formation of AldFe,Mn)3Si and Mg2Si dispersoids.

Jan 1, 2008

By Li Qian

Mechanisms of bio-dephosphorization from iron ore was investigated in this Paper. The results show that there are two bio-dephosphorization ways from iron ore, the one is that Acidithiobacillus ferrooxidans directly derive phosphorus from the ore, the other is phosphorus is able to be leached acid produced during metabolizing of Acidithiobacillus ferrooxidans, and the latter is more important than the other. Adding suitable pyrite can enhance the bio- dephosphorization process through providing nourishment and producing acid directly due to S 3oxidized or indirectly due to Fe3 as oxidant. The potential varies in the range of 0.434~0.498V and pH is in the range of 2.5 ~ 1.25 during bio-leaching process. It can be founded that, according 2+to the E-pH graph of Fe-H2O system, Fe wouldn?t be oxidized under sterile system in this potential and pH ranges. It can be obviously concluded that the Acidithiobacillus ferrooxidans are 2+able to reduce the potential for the oxidization of Fe and make the oxidization occur in the above pH and potential zone, so the bio-leaching process can proceed. the investigation of E-pH graph of P-H2O system show that H3PO4 can exist steadily.

Jan 1, 2009

By D. M. Hausen

It has been demonstrated that microscopic techniques can be applied in a practical manner to the study of spodumene liberation in the processing of pegmatitic ores at the Kings Mountain spodumene plant, Kings Mountain, North Carolina. Spodumene and associated non-opaque gangue minerals are identified and quantified by microscopic point-counting of polished thin sections of heads, concentrates, middlings and tails fractions. Specially prepared polished thin sections? provide uniform thickness of particles for measurement of diagnostic optical properties and the alternate use of incident and transmitted light in distinguishing the various gangue and ore minerals. Spodumene is commonly associated and interlocked with quartz, albite, microcline and muscovite. Concentrate grade depends on the degree of spodumene liberation, which in turn depends on the crystal size and textural association of interlocked minerals. The liberation of spodumene can be measured as a function of screen size by means of microscopic point-count data. Microscopic data also provide useful metallurgical information about the nature of diluent minerals in spodumene concentrates, and the form of lithia losses in the tails. Lithium assays correlate closely with microscopic spodumene analyses in various flotation products from Foote Mineral&apos;s Kings Mountain plant, and confirm the applicability of quantitative optical microscopy to the study of liberation and recovery of spodumene from pegmatitic ores. A better understanding of recovery-grade relationships was developed as a result of quantitative microscopy studies.

Jan 1, 1981

By R. F. Hammen

Copper is one of the most widely used metals in industrial processes and is also present in most mining operations. Extraction of copper from solutions often proves difficult due to the presence of complexing agents. ChromatoChem, Inc. has developed a Solid Phase Extraction (SPE) support (HiPAC) for removal and recovery of metals from wastewater. The HiPAC SPE support employs chelating agents covalently coupled to a long linker molecule. Several solutions containing copper and complexing agents were tested including 1) copper and carbonate, pH 9.8, 2) mixed metals and anions with copper and cyanide, pH 11, and 3) copper and the chelating agent EDTA, pH 11. The copper was extracted from solutions one and two at high pH, but the EDTA containing solution needed the pH lowered to make the copper available for capture. In each example, the copper concentration was significantly reduced by HiPAC SPE treatment.

Jan 1, 1994

By Shenghui Guo, Jian Chen, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"Response surface method (RSM) based on mono-factor experiment was applied for the process optimization of sintering of chromite fines by microwave. In RSM analysis, effects of binder addition amount, sintering temperature and holding time on the compression strength and shatter strength of the sinter were examined. Results showed that the optimal values of the above parameters were determined as follows: binder addition amount of 1.90% (in mass), sintering temperature of 1153? and holding time of 16 min. Under the optimized conditions, the compression strength was 11155.8? and shatter strength was 95.6849%. The results show that the process was optimized by response surface methodology is stable and feasible, and provide a new way for sintering of chromite fines.IntroductionChromite ore is the main feedstock for ferrochrome, and ferrochrome can be used as steelmaking additive to produce a variety of great strength, corrosion resistant and oxidation resistant special steel, which can be widely used in the aerospace, automotive, shipbuilding, military departments[1], and it has important strategic significance. At present, among the annual world's mined chromite the number of lump ore continues to diminish with its price rising sharply, while the proportion of ore fines been always increased, and the difference in prices between ore fines and lump ore is growing[2]. Despite the low price of chromite fines, and its rich in resources, it can be only used for ferrochrome smelting after agglomeration. Thus manufacturing blocks by using cheap chromite fines is an effective measure to reduce the cost of ferrochrome production and use the chromite resources[3]."

Jan 1, 2013