Search Documents

By Helvio P. G. Santafé Jr., Ruben J. S. Rodriguez, Sergio N. Monteiro, Teresa E. Castillo

"The coir fiber extracted from the husk of the coconut fruits are worldwide available in tropical regions as a low cost lignocellulosic by-product for many applications including composite filler in automobile parts. Possible uses above room temperature require information on the thermal behavior of these coir fiber composites. Therefore, the objective of this work was to perform thermogravimetric, TGA and DTG, analysis on polyester matrix composites incorporated with different volume fractions of coir fiber. In general, it was found that thermal degradation associated with weight loss occurred in three stages. Changes were also observed in the DTG peaks that could be attributed to the coir fiber participation through the decomposition of its lignocellulosic structure.IntroductionThe development of new materials has always been motivated by the need of improved properties. This was the case of modem composites with combination of properties that surpass those of conventional monolithic metallic alloys, ceramic or polymers, from which composites are made. A typical example is the synthetic fiber reinforced composite with specific strength i. e, ultimate stress divided by density, higher than any other monolithic material. Today, however, our global society is concerned with serious environmental problems and thus demanding that new materials be developed with distinct characteristics. They are known as environmentally correct and are expected to be sustainable, which corresponds to the condition of being biodegradable, renewable, recyclable and neutral with respect to C02 emission, considered the main responsible for global warning [1]. Synthetic fiber composites cannot meet these requirements. Consequently, new composite reinforced with cellulose-based natural fiber are being developed [2-8] and are already replacing the synthetic ones in several engineering fields including the automobile industry [9-11]. These composites have additional advantages owing to the lignocellulosic fiber benefits of being diversified, abundant, less expensive, lighter and of societal interest [8]. In some cases even technical advantages such as non-abrasive effect to processing equipments and more flexibility exist in comparison to synthetic fibers."

Jan 1, 2011

By A. E. M. Warner

Inco Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By Gervais Soucy, François Quesnel, Pierre Hovington, Wen Zhu, Karim Zaghib, Jocelyn Veilleux

The properties of lithium titanates anodes in Li-ion batteries are highly dependent on their secondary constituents. While their main phase is usually constituted of Li4Ti5O12, significant quantity of lithium titanates compounds of various stoichiometry are often present, due to either the processing, usage or aging of the material. These may go underreported, as many of these spectrums overlap or display low signal in X-ray diffraction (XRD). Samples of nanosized lithium titanates synthetized by inductive plasma were characterized by XRD and scanning electron microscopy (SEM), as they provide a regular yet typical crystallite size and shape including multiple phases. A Rietveld refinement was developed to extract the composition of these samples. Mass balance through further annealing and differential scanning calorimetry (DSC) enthalpy measurements from phase transformations were also used as identification and validation techniques.

Jan 1, 2015

By W. S. Kirk

World cobalt production in 1987 was estimated to be about 26,600 metric tons (MT) of which Market Economy Country (MEC) production was estimated to be about 22,000 MT. Zaire and Zambia produce about 80 percent of the primary cobalt produced among Market Economy Countries (MEC). Production cutbacks. lowering cobalt grades and mining curtailments in Finland and Zambia in 1987, resulted in lower production than that of 1986. The trend is expected to continue through 1988. Cobalt production from Canadian ores and from Botswana is expected to increase significantly in 1988 as a result of increased nickel production. MEC production in 1988 is estimated to be 22,100 MT, only slightly higher than that of 1987. There are currently no primary cobalt mines. Virtually all cobalt is recovered as a byproduct of copper and/or nickel mining. Zaire, which produces cobalt as a byproduct of copper, is the worlds largest cobalt producer, with over 50 percent of total estimated world cobalt production and nearly 65 percent of MEC production. Zambia follows with about 14 percent and 17 percent, respectively. Zambia's cobalt production also results from copper production.

Jan 1, 1988

By Jiling Wang, Xuefeng Liu, Haojian Duan, Lifeng Zhang, Ying Ren, Wen Yang

"In order to study the influence of MgO-C refractory on steel cleanliness and inclusions during steelmaking process, and to understand the reaction mechanism deeply, laboratory deoxidation and equilibrium experiments were respectively performed in MgO crucibles at 1873K. In the former experiment, after Al addition, steel samples were taken at different holding time. In the latter experiment, different slag components and different contents of carbon and aluminum in steel were considered respectively. The inclusion characteristics of each experiment were analyzed. The results showed that with the increasing of holding time after deoxidation by Al, MgO existed in the small inclusions firstly, and then in the large ones such as the clusters. The MgO content in the inclusions increased with the increasing of holding time, indicating that the MgO in crucible could be individually reduced by the aluminum in the molten steel. The reaction could occur within nine minutes.IntroductionNon-metallic inclusions would have positive or negative effect on steel quality depend on the quantity, size and composition of inclusions. Large inclusions are always detrimental. From the point of view of inclusion property, plastic inclusions are required by steel cord, while hard inclusions are preferred by pipeline steel. One of the most important ways to increase the steel quality is reducing the inclusion size and controlling the inclusion composition in steel. Nowadays, MgO based refractory is used as ladle glaze material with more and more frequency, which results in different inclusion characteristics in molten steel, for example, the inevitable generation of MgO contained inclusions during ladle treatment of steel. In other words, the inclusions in this type ladle will influence on the steel cleanliness and the product property. Thus, keeping an eye on the inclusion formation behavior in the steel with MgO-C ladle glaze is important for the steel industry. There have been a few studies in this regard. Li et al[l] studied the reactions between MgO-C refractory, molten slag and metal using a high temperature X-ray radiographic apparatus. They found that the local corrosion was regarded as due to the cyclic dissolution of MgO and graphite in the refractory into slag and metal phase. The gas bubbles formed according to the reaction of (FeO)+C(s)=Fe(l)+CO(g) greatly influenced the corrosion. On an industrial scale, Du[2] found that ladle glaze is a major source of inclusions in the ladle. An experimental study has been performed by Lehmann in order to estimate the importance of the reaction between a MgO-based tundish refractory and an Al-killed steel[3]."

Jan 1, 2014

By Niander A. Cerqueira, Pâmela Berçot, Afonso G. Azevedo, Victor B. Souza, Victor T. Bartolazzi, Bruno Padilha

In recent years, concern about environmental issues has become a parameter to consider in the projects in engineering. In order to reduce the impact that the tire improper disposal may result for the environment, we sought a solution to this problem. This article proposes the use of rubber scrap tires as fine aggregate in concrete production. The material produced was analyzed by a bending test, resulting in product quality, in particular for application in situations requiring a more ductile material.

Mar 1, 2017

By Kenneth S. Coley, Michael Pomeroy, Elaine Chen

Recent work on modeling of BOF steelmaking is reviewed, highlighting the critical aspects of each approach. It is concluded that the most successful models should be based on a deep understanding of the mechanisms and kinetics of the critical reactions. The importance of the decarburization mechanism is discussed with particular reference to its role in droplet swelling or bloating which has a profound influence on the droplet residence time in the slag. Conditions which cause bloating are discussed and the rate determining step is proposed to be primarily nucleation of CO bubbles inside the metal droplet with some influence from growth by reaction at the bubble/metal interface. The discrepancy in the super-saturation ratio required for classical nucleation is discussed and an approach using a surface tension modifying parameter is illustrated. Finally, the role of CO nucleation in controlling the driving force for dephosphorization is discussed.

Jan 1, 2014

By J. R. Sarazin

Density driven convection during solidification has been recognized for some time to result in macrosegregation particularly when lower density alloying elements are rejected into the interdendritic liquid. The resulting segregates are commonly referred to as channels, freckles or A-segregates. Buoyancy driven convection leading to channel formation has been examined in three model systems possessing somewhat different materials parameters. They are the Pb-Sn eutectic system, the transparent aqueous-salt NH C1-H 0 4 2 eutectic system and the transparent organic succinonitrile-ethanol monotectic system. Convection in these systems is controlled by a balance of buoyant and viscous forces, which are strong functions of composition and temperature. Composition, temperature and flow velocity were measured and elimination of channels through heavier ternary additions is discussed.

Jan 1, 1991

By James C. Foley

In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ monitoring of acoustic amplitude and velocity as sintering proceeds. Samples were made from elemental powders of Al (99.99%), Al (99.7%), Ag, (99.99%), Cu (99.99%) and Fe (99.9%). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and amplitude during sintering. The changes in acoustic properties were correlated with mechanical properties. Evolution of a series of reverberating echoes during sintering is shown to provide information on the state of sintering, changes in sintering kinetics as well as having the potential for detection of interior flaws.

Jan 1, 2001

By Jie Li, Shu Yang, Zhongliang Tian, Xun Hu, Yanqing Lai

The purity of the electrolyte has an important influence on the content of the impurities in electrodeposited silicon. In this paper, effects of electrolysis temperature, current density and the time on the concentrations of two important impurities: phosphorus and iron in the electrolyte were investigated during the purification of Na3AlF6-10%K2SiF6-AlF3 melt. It was observed that the concentrations of P and Fe in the electrolyte decreased with the electrolysis temperature, current density and the electrolysis time increasing. X-ray fluorescence (XRF) of the electrolyte shows that the concentrations of P and Fe decrease from 4.2ppmw to 1.3ppmw and 204.0ppmw to 42.6ppmw, respectively. The removal rates of P and Fe are 69.08% and 79.12% when the electrolysis was performed for the duration of 3 hours and at a current density of 20mA·cm-2 while the operating temperature was 1225K.

Jan 1, 2015

By Mizraim Uriel Flores, Elia Guadalupe Palacios, Sayra Ordoñez, Iván Alejandro Reyes, Ister Mireles, Martín Reyes, Francisco Patiño, Hernán Islas, Víctor Hugo Flores

This paper presents the characterization of a sample of mercury jarosite that was synthesized by slowly adding Hg(NO3)2H2O into a Fe2(SO4)3nH2O solution. X-ray diffraction (XRD) analysis performed on the sample confirmed that the compound presents a crystal phase corresponding to mercury jarosite. Analysis through Scanning Electron Microscopy with Energy Dispersive X-ray Spectroscopy (SEM-EDS) determined that the precipitate is composed of mercury, sulfur, iron and oxygen. It is made up of spherical particles with an average size of 38 μm; these particles are made of rhombohedral micro-crystals with sizes ranging between 1 and 2 μm. Chemical characterization was performed through dichromatometry analysis, gravimetry and atomic absorption spectroscopy (AAS), thus obtaining the following composition: 27% Fe3+, 37% SO4 2− 14% Hg2+, 22% OH− + H3O+ + H2O. The following approximate formula of the compound was determined from chemical analysis: [Hg0.39(H3O)0.22]Fe2.71(SO4)2.17(OH)4.79 (H2O)2.09.

Mar 1, 2017

By Yongqi Sun, Zuotai Zhang

Our study investigated the influence of P2O5 and B2O3 on the viscosity and crystallization behavior of Ti-bearing blast furnace (Ti-BF) slags for the purpose of Ti extraction. The investigation of the crystallization behaviors were carried out using a single hot thermocouple technique (SHTT) and the viscosity was obtained by rotating cylinder method. For the viscosity, the results showed that P2O5 substantially increased the slag viscosity. P2O5 is a network-forming oxide, which increased the degree of polymerization of slags and accordingly increased the slag viscosity. However, both of slag viscosity and apparent activation energy for viscous flow remarkably decreased with B2O3 addition. As a typical network forming oxide, B2O3 was introduced into the network and existed dominantly as 2-D structure, BO3 triangular, which caused a simpler structure and a decreasing slag viscosity. As for the crystallization behaviors of Ti-BF slags, both P2O5 and B2O3 enhanced the crystallization trend of rod-shape rutile and suppressed the crystallization trend of dendrite CaTiO3. Therefore the added P2O5 and B2O3 caused the primary phase change from CaTiO3 to rutile. Additionally, it was found that the rod-shape rutile showed a 1-D growth, whereas the dendrite CaTiO3 showed a 3-D growth style.

Jan 1, 2015

By C. Beckennann, C. Y. Wang

"Computer simulations of structural and compositional development in equiaxed dendritic alloy solidification are performed using a recently developed multi phase model. The model not only accounts for the transport phenomena occurring on the macroscopic (system) scale, but includes also the grain nucleation and growth mechanisms taking place at various microscopic length scales. In this paper, a numerical technique consisting of a fully implicit control-volume based finite difference method and a multiple time step scheme is developed for accurate and efficient simulations of both micro- and macro-phenomena. Sample numerical results are presented to reveal the effects of liquid now and crystal sedimentation on segregation and the final grain size distribution. In particular, the importance of the interplay between the dendrite microstructure and multiphase now patterns is shown.IntroductionIn recent years, modeling of equiaxed dendritic solidification without convection has experienced considerable progress (1,2]. Nucleation and growth kinetic laws have been coupled with transient heat conduction calculations to determine the solidification microstructure. However, modeling of equiaxed dendritic solidification with melt convection and solid movement has not been attempted so far, largely because of the complications associated with the transport of free equiaxed crystals in the melt. The gravity-induced transport of free crystals is fundamental to the development and extent of the equiaxed zone and also greatly affects the columnar to equiaxed transition. Another possible effect of crystal sedimentation or floatation is to cause severe macrosegregation as well as structural inhomogeneities. The only study available in the literature that accounts for both liquid convection and solid transport is by Ni and Beckermann (3], but deals with globulitic structures (as opposed to dendritic)"

Jan 1, 1994

By Animesh Jha, Chris Dometakis

"Without the use of a flux, only a poor dispersion of ceramic phase can be achieved. A molten-flux-assisted ceramic phase dispersion technique for producing aluminium alloy metalmatrix composites has been developed. In this paper, we report the physical chemistry for the dispersion of TiB2 in molten aluminium. In particular, aspects of the interfacial energy and the thermodynamics of the dispersion reactions are briefly discussed for enhancing the volume of dispersion phase in the molten metal and for controlling their morphology. This investigation also addresses the role of molten flux in the fabrication of AI-alloy mmc using a casting technique. The morphological aspects of the dispersion are explained on the basis of the classical theory· of nucleation.IntroductionMetal matrix composites (MMCs), have long been recognised as an important class of material due to their greater wear resistance, specific stiffness and temperature capability when compared to conventional monolithic alloys. Particulate reinforced composites produced by melt casting techniques have been amongst the first MMCs to achieve commercial market viability. The advent of melt mixing techniques such as the Duralcan™ process have enabled low cost, easily fabricated composites based on the AI-SiC and AIAlz0 3 systems to be produced. In this process, uncoated ceramic particles with diameters 10ltm and larger, are incorporated into conventional monolithic alloys with reinforcement levels up to 25 volume percent. The AI-7Si-SiC metal-matrix composites have good wear resistance, high strength, low density and high thermal conductivity. The combination of these physical and mechanical properties has become a major attraction for the fabrication of light-alloy composite disc rotor brakes for the automotive sector2. However, in silicon-free alloys, SiC is thermodynamically unstable above the composite melting point and is extensively attacked by the melt to form aluminium carbide3 :"

Jan 1, 1996

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a'=0.407 nm for two axes and c'=0.390 nm for the third axis. The a'axis is shorter by 4% than the c'axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By Abbas H. Mirza

Arsenic and selenium are found in low quantities together with other metals in several nonferrous metallurgical process streams such as scrubber blowdown solution, acid plant wastewater, gas cleaning plant water, etc. Normally, the other metals in these streams are present as cations and can be precipitated by conventional lime treatment and sulfide polishing. However, arsenic and selenium are invariably present as anions, AsO33-and AsO43 in the case of arsenic and SeO32 and SeO42 for selenium. Conventional lime treatment removes most of the arsenic, but it does not remove selenium. The present paper reviews the processes and technologies developed to date on the removal of arsenic and selenium from metallurgical process streams.

Jan 1, 1996

By Dan Wang, Yuanbo Zhang, Guihong Han, Guanghui Li, Tao Jiang, Yanfang Huang

"Hematite concentrates are characterized by bad high-temperature reactivity and poor balling index, which restrict their large-scale application in the production of oxidized pellets. An organic additive, namely MHA, was authorized and used as binder recently in China. Compared with bentonite, the effects of MHA on compressive strength of hematite pellets at various firing conditions were investigated in this study. Experimental results showed the compressive strengths of preheated pellets with different binders were increased with increasing the preheating temperature and time. The compressive strength of preheated pellets with MHA binder was lower than that of pellets with bentonite, which can be ascribed to the high porosity of pellets with MHA binder. However, the compressive strength of roasted pellets with MHA binder was higher than that of pellets with bentonite. The compressive strength of finished pellets balled with MHA binder 1.0 wt% could meet the operation requirements of grate-kiln process.IntroductionHematite concentrates are characterized by bad high-temperature reactivity and poor balling index, which can lead to the appearance of those problems with increasing the energy consumption, shortening the useful life of equipment, and finally increasing the operation cost of oxidized pellets plants [1-2]. Some investigations have been conducted based on improving the pelletizing technique of hematite concentrates, such as pretreatment of raw materials [3-7], optimization of ore proportioning [8], addition of solid fuels [9-16], and so on. Employing high pressure grinding roller for the treatment of hematite concentrates revealed that the mechanical strength of wet green pellets could be improved. However, the mechanical strength of fired pellets was not improved obviously [7]. Huang, et al., pointed out that the preheating and roasting temperature may be decreased and the compressive strength of fired pellets could be increased by blending a certain proportion of magnetite concentrates with hematite [8]. Nevertheless, there are a variety of magnetite ores different in physical and chemical properties in China, resulting in the instability operation [17]."

Jan 1, 2012

By Raymond E. Healy

Mercurian e1ectrum (Au-Ag-Hg alloy) is the principal Au-bearing phase in the massive sulphide ores at Trout Lake, Manitoba. The average composition of this phase (in wt %) is 49.2 % Ag. 38.7 % Au and 11.0 % Hg, with ranges of 17.34 to 76.47 % Ag, 1.62 to 79.86 % Au and 1.29 to 30.87 % Hg. Compositional variation reflects solid solution in the a-phase of the Ag-Au-Hg system. Backscatter electron imagery reveals systematic zoning and suggests a general crystallization sequence from metamorphic pore fluids of progressively Ag-rich compositions. Investigation of the occurrence of gold in mill products demonstrates that mercurian electrum accounts for over 90 % of the Au in Trout Lake ore. I Invisible" gold in pyrite (x = 0.72 ppm Au) and arsenopyrite (x 30.2 ppm Au) is confirmed by SIMS analyses, and accounts for 7-10 % of the Au in the ore, and 35 % of the Au lost to the tailings. The remaining 65 % of the Au lost to the tailings consists principally of mercurian electrum locked with pyrite. No significant losses of mercurian electrum in the size range amenable to flotation and/or regrinding is indicated.

Jan 1, 1989

By J. L. Johnson

Remediation of small-arms firing ranges is being investigated by the Naval Civil Engineering Laboratory and the U.S. Bureau of Mines. Scheduled closures of military installations, as well as the management of active ranges, require the development of methodologies for heavy metals removal to prevent their entering the surrounding environment. The impact berms contain high concentrations of metals, and the soil and vegetation surrounding the berms were found to have slightly elevated levels. The heavy metals characterized are in the form of whole bullets, a wide size distribution of free fragments, smeared lead on the surface of the soil grains, and very finely attached particles. Gravity beneficiation can remove liberated metal contamination effectively. Weak acetic acid leaching shows promise in lowering the final metal contamination to allow the soil to pass the Environmental Protection Agency's (EPA) Toxicity Characteristic Leaching Procedure (TCLP) criteria.

Jan 1, 1991

By Z. Jing, C. Jun

High-purity Bi2O3 was prepared via extraction-preparation stripping method use BiCl3 leaching solution. Parameters such as oxalic acid concentration, phase ration, aging duration, feeding duration, were examined for their effect on the size and morphology of precipitate. The precipitate was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), particle size analysis, differential scanning calorimetry and thermal gravity analysis (DSC-TGA) and infrared spectroscopy analysis (FT-IR). Bi2O3 was characterized by elements analysis, particle size analysis and scanning electron microscopy (SEM). Bi2O3 product of 680 nm was obtained using 15 g/L oxalic acid, 1/1 phase ration, 0 min aging duration, 0 min feeding duration and calcinating at 500 °C for 2 h.

Mar 1, 2018