Search Documents

By Helmut Hass, Marco Ziller

"Abstract: 1 Sophia Spoortunnel Marco Ziller, Trevi S.p.A.:For the construction of 14 cross passages connecting the twin tunnels of the Sophiaspoortunnel the Artificial Ground Freezing technique was applied as temporary soil improvement. AGF by Brine and Liquid Nitrogen was implemented. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil during the freezing intervention in order to control the behaviour and the efficacy of the treatment.IntroductionThe Sophia rail tunnel is a bored tunnel with a length of 4.24 km, comprising two separate parallel tubes with an outside diameter of 9.45 m. The twin tunnels were excavated by a TBM equipped with hydroshield. Seven service shafts, approximately 30 m deep, were constructed in between the tunnels. From each shaft two cross passages were constructed connecting the shaft with both tubes, for a total of 14 cross passages.The Artificial Ground Freezing technique utilizing both the Brine and Liquid Nitrogen methods was used for temporary waterproofing and soil support to allow the excavation of the cross passages. The natural soil to be frozen was consisting in loose sand and clay under a hydrostatic pressure up to 250 kPa.For the measurement of the ground temperature. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil and at the contact with the tunnel lining. Furthermore, a comprehensive computerized system of sensors and cryogenic valves was designed and implemented in order to manage the whole Nitrogen process.Soil Main CharacteristicsThe soil stratigraphy is generally consisting in Clay (Holocene) from ground level to -15 m depth, followed by Pleistocenic Sand, from -15 to -25 m, and Clay below -25 m."

Jan 1, 2014

By M. R. Geer, H. F. Yancey

"INTRODUCTION Throughout the history of coal washing, the jig has been one of the most important coal-cleaning appliances. In 1935 34.7 percent of the 45,361,021 tons of clean coal produced was the product of jigging. 4/ Previous to 1928, most of the jigs used in the United States were of the piston type, with which sufficient mobility to allow stratification in bed is imparted by the reciprocating up-and-down movement of a piston in the water compartment adjacent to the screen compartment. In 1928, the Baum type of jig was introduces in this country and has since come into wide spread use. In this type, water pulsations are imparted by application and release of compressed air to the water compartment. All prior studies of the mechanism of seperating cleared coal from impurity by piston-type jigs. 5/ The same laws of settling, of course, apply to both types, piston or Baum, but the character of the separation with the Baum type may be modified more easily because of the flexibility with which air may be handled, as distinguished from the fixed action of eccentrics commonly used in piston jigs. Since no detailed studies are available to show the performance, that is, the character of the separation between coal and impurity, of the Baum type the Bureau of Mines undertook the investigation recorded in this report."

Jan 1, 1938

By Don K. Smith

The Reclamation Program for the Northern Zone of the Indus Plains in West Pakistan involves the construction of 30,000 irrigation wells to serve 20 million acres with an annual pumpage of nearly 40 million acre-ft. Detailed hydrologic studies indicated that mild steel would be satisfactory for casing; however, within two years after construction, about 10% of the wells began to fail due to encrustation and corrosion of the casing. A search to find a noncor-rosive substitute for the steel casing disclosed that only fiberglass-reinforced plastic pipe satisfied all requirements. The results of initial use of fiberglass have been highly satisfactory and have resulted in a lower over-all well cost. Advances in technology pomise further reduction in prices and improvement in performance. The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc., of Denver, Colo., as engineers for the program in the northern zone of the Indus Basin. This program consists of the construction of about 30,000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and involve an annual pumpage from groundwater storage of nearly 40 million acre-ft of

Jan 1, 1970

By J. Hansen

"ABSTRACTThe paper addresses the application of automated monitoring, control, and navigation to improve dragline performance. SummaryImproving dragline performance in the Canadian coal mines is critical to the continued success of the industry. Draglines represent a large capital investment and coal prices are low by historic standards. This paper argues that the introduction of monitoring, control, and navigation on draglines offers an opportunity to significantly reduce a dragline’s operating cost per cubic metre moved. To place the importance of this in perspective, a North Dakota mine calculates that every 1% increase in dragline productivity means a savings to the mine of US$340,000 per year. MonitorsAutomated dragline monitoring is a well established technology with commercial products available since the early 1980s. The three main reasons for placing monitors on draglines are (Walker, 1993):1. productivity increases: reduce variations between different operators’ performance across different shifts;2. quality increases: increase the percentage of ore and waste loads that go to the correct destination; and3. special projects (engineering projects): justify installing static field exciters and regulator upgrades; implement power management; aid operator training; study high performance buckets, rigging changes, and various excavation sequences.Mines as diverse as Kennecott’s Cordero- Rojo Complex in the United States and Natal Coal Corp.’s Optimum Mine in South Africa report dragline productivity increases of 10% to 20% in the region attributed to the implementation of dragline monitoring."

Jan 1, 2000

By D. Symonds, A. J. Richins, M. G. Nelson

Mining activities at Kennecott and Park City are similar in that both districts began operation in the last half of the 18th century, and both operated on a large scale for many years. However, they are different for two important reasons. First, the mines in the Park City district were always underground. The city of Park City was above many of those mine workings. It remained in place after mining activity stopped, and as the town became an up-scale ski resort, property values increased and the tailings dumps became desirable building sites. In contrast, Kennecott eventually became an open pit mine, and the growing pit effectively consumed many of the small towns that had grown up around the underground workings. Even towns on the periphery of the open pit were razed to allow for the disposal of mine overburden. Second, almost all mining activity stopped in Park City in the early 1970s, just as the first rigorous environmental legislation in the United States was enacted. (The Ontario mine operated sporadically until 1982.) Many mine structures, waste dumps, tailings ponds and piles, and tunnels were simply abandoned as the mining companies ceased business or were bought out. Kennecott, on the other hand, has been in continuous operation for more than 120 years, so a closure plan hasn’t been finalized. Nonetheless, environmental and social problems have arisen, and the company has had to address them.

Mar 2, 2022

By R Tweedie

'The politics of mining in New Zealand' is a topic I chose myself because of its importance in the future of the New Zealand mining industry. There are many people in the industry who are cynical about politics, cynical about politicians and definitely cynical and often critical of political decisions. In fact, many industry people say they don't want to get involved in politics, they just want to get on with the business of exploration or mining. The point of my address is that politics is important and the industry cannot afford not to participate in the political process.

Jan 1, 1991

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By Leonard Weixler, Peter Halbach, Michael Jarowinsky, Johannes Post

Germany as an industrial nation is highly dependent on the import of mineral or metal resources. Sources which have not been considered until now are the marine mineral resources (MMR), which in recent times are enjoying more and more increasing interests and which might provide in the future a considerable contribution to the supply security on metal resources not only for the industrial countries. Backed up by the German government’s "National Masterplan Maritime Technologies" (NMMT) and corresponding industrial R&D-activities, the idea and the advantages of deep-sea mining is gaining more and more interests and supporters with respect to industrial and political considerations on strategic raw material resources as well as on the development of deep-sea mining technologies. The NMMT aims to initiate growth and increase the competitiveness of the German maritime industry on international markets and covers about 10 different marine and ocean technology sectors including deep-sea mining.

Sep 1, 2014

By Andres Salazar, Carlos Delgado Robles, Richard K. Preece

Minera Escondida, located in the Antofagasta Region of northern Chile, is the world’s largest producer of copper as concentrate and SX-EW cathode. Projects to increase mill and flotation capacity began soon after start-up in 1990 to off-set decreasing copper grade. Subsequent projects had the objective to increase copper production through heap leach and SX-EW production and a second concentrator. The mine footprint concurrently expanded peripherally from the central high-grade enriched core of Escondida and then into the separate Escondida Norte deposit. Early in the mine life, metallurgical forecasting that was based on metallurgical composites of presumed ore types and historical plant production was adequate for operational planning, plant design, and project valuation. This approach became unreliable, however, as the increase in mine footprint was accompanied by an increased variability in key ore body characteristics such as hardness, copper-iron sulfide mineralogy, and sulfide liberation textures that were not reflected in the geological criteria used for ore type designation. The project study teams turned to small-scale physical and chemical tests to better characterize the spatial distribution of these key ore characteristics. Programs associated with capital growth projects were carried out through the mid-2000s to sample and construct a three-dimensional spatial model of hardness, copper sulfide mineralogy, and rougher flotation recovery from tests on 15-m drill core composites. Mathematical models were developed from the respective ore characteristic data to calculate throughput, flotation recovery, and concentrate copper grade. The spatial models were integrated with the concurrent mineral resource block model using standard geostatistical methods and the metallurgical process calculations were applied to the block estimates. The geometallurgical model, originally constructed on a project basis, is now managed by a dedicated team reporting to the manager of Geosciences & Resources Definition in the Escondida organization. The model has evolved with increasing complexity of the mine and processing plants and currently includes seven forecasting areas for three concentrators and four areas for two leach plants. Metallurgical forecasts of mill throughput, final flotation recovery, and concentrate copper grade still have the highest relevance to mine planning and optimization. Sample preparation, test procedures, and quality control methods are summarized for the ore characteristic tests important to these forecasts. Analytical results from recent annual sampling programs are presented for the hardness indices, rougher flotation recovery, and partial extraction copper analyses. Geostatistical analysis of the SAG mill hardness index is summarized as an example for the spatial estimation process. Mathematic models are presented for throughput (based on hardness indices), final flotation recovery (based on rougher recovery and plant calibration studies), and concentrate copper grade (based on sulfide mineralogy and empirical pyrite rejection studies).

Aug 31, 2023

By J. Petersen, T. Moyo, D. Maharaj

This study investigates the effect of ammonium thiosulfate on the leaching of gold from the contacts of unpopulated cut electronic printed circuit boards (PCBs). Studies in the literature show ammonium thiosulfate to be a viable option in comparison to the commonly used but hazardous cyanide leaching route. However, the simultaneous dissolution of Cu interferes with the Au leaching reaction, often limiting the extraction to moderate levels. To optimize the system, an ammoniumthiosulfate system containing 0.5M ammonia, 0.5M ammonium thiosulfate, and Cu(II) sulfate at varying concentrations was studied as an alternative hydrometallurgical option for the recovery of gold from PCB. Tests were done with unpopulated standardized model PCBs (cut to 15 x 30mm pieces). Gold extraction of 47.3% was achieved after a 24-hour leaching experiment with a 0.02M copper background concentration. Further experiments focused using different initial background Cu concentrations (0M – 0.1M) to determine its effect on both gold and copper extractions. An initial Cu concentration of 0.045M resulted in the highest gold extraction, with 93.7% extraction after 6 hours of leaching. Further analysis of the data shows that the kinetic rate of gold leaching is correlated in a first-order dependence with the actual copper concentration in the solution, which increases with the concomitant dissolution of copper and gold from the PCBs. A lower threshold of 0.017M and an upper threshold of 0.15M copper in solution were determined, in between which gold extraction shows this first-order rate increase. The upper threshold is potentially linked to the onset of copper precipitation, which blinds the metal surfaces, slowing further leaching. The findings of this study suggest that in an industrial recovery operation of gold from waste PCB using the thiosulfate method, copper concentrations need to be carefully monitored, and the process should preferably operate with uncut or coarsely cut untreated boards to minimize exposure to copper circuits.

Dec 11, 2024

By Balmer Neilly

To one with so little experience in matters pertaining to currency, international finance, and foreign trade, this is surely an ambitions venture on my part. However, this is a subject of prime importance to all seriously minded Canadians and, if we are to obtain any clear understanding of the factors involved, we must study the facts and debate such points as may remain at issue. During the last few years, the world' s better known economists have described the gold standard in all its ramifications and in such detail as to leave many of us even more confused than before. If we, then, are to acquire any real conception of its meaning and use, I think we must reduce it to its fundamentals and start from there. To my way of thinking, gold in ? trade and commerce is the symbol of honesty. When you seek to discharge a debt by tendering paper you hand the recipient an I.O.U. which may or may not be good, for the purchase of goods or services to the extent of its face value. When, however, you discharge a debt by the payment of gold, it constitutes a complete and final discharge. There are no reservations - no ifs and ands - and the transaction is definitely closed to the satisfaction of all concerned. Gold, then, is evidence of accumulated and transferable wealth that is immediately acceptable in practically every part of the world. However, there is not nearly enough gold to meet the demands of world trade, and. many years ago this deficiency gave rise to what we now describe as our banking system.

Jan 1, 1949

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By J. E. Nesset, S. R. Rao, J. A. Finch

"For base metal sulphides, iron rejection starts in mineral processing. This review focuses on changes in plant practice specifically to improve iron sulphide rejection by control of contaminant ion effects and discusses selected general innovations in mineral processing that can be expected to play a role. One group of changes to control contaminant ions is in size reduction (the use of stage grinding and inert stirred milling) and another is in system chemistry (order of reagent addition and exploitation of the flexibility of sulphoxy reagents). Plant examples illustrate the successes, indicating that there are several options available. The general innovations start by considering the new tools for measuring gas dispersion properties and quantifying froth characteristics by imaging. Examples of their application to improve concentrate quality illustrate the potential. Other innovations stress adapting geostatistics to model variation in milling and flotation response to provide feed forward control and rigorous application of statistical experimental methodology in plant test work. An example from one concentrator shows improvements in concentrate quality from application of basic principles can be impressive.INTRODUCTIONThe more iron control (rejection) that can be accomplished in mineral processing the lower the subsequent metal extraction costs and environmental implications of iron disposal, particularly in hydrometallurgical processes. Iron rejection has been a contributing target to periodic attempts to apply mineral processing to nickel laterites and bauxites but the prime application is control of pyrite and pyrrhotite (iron sulphides) in the treatment of sulphide ores by flotation. In this paper some new concepts and innovations introduced in sulphide flotation plants over the past ten years or so (i.e., since a previous review [1]) will be outlined with examples of how they have contributed to improved “iron control”.To increase rejection of iron minerals, first the recovery mechanism should be understood. There are four principal ones, two physical in origin: 1, via locked particles (i.e., flotation of composite particles due to insufficient size reduction to liberate the minerals) and 2, through entrainment in the water reporting to the float product (an unselective process); and two originating from a response to the system chemistry: 1, true flotation (i.e., iron sulphides becoming hydrophobic) and 2, as a result of iron sulphides forming aggregates with hydrophobic particles (e.g., ”slime” coatings). There has been considerable effort to diagnose which of these dominates iron sulphide recovery; in many cases it is due to “chemistry”, in particular true flotation. The flotation effect often appears related to contamination by metal ions [1]. This can reduce selectivity in two ways: 1, metal ion species may activate iron sulphides, or 2, cause general depression which demands more vigorous flotation conditions (e.g., additional collector) with consequent loss of selectivity. This is where the review will start, by considering ways to control contaminant ions."

Jan 1, 2007

By S C. Dominy

The gravity recoverable gold (GRG) parameter reflects liberated gold or gold-dominated composite particles that can be recovered by gravity separation. Recoveries depend upon mineralogy, in situ particle size and the comminution and extraction method used. Any ore bearing >15 per cent of gold greater than 50 ¦m in size is likely to have a GRG component. The principal characterisation methodology applied is the three-stage GRG (3GRG) test, based on a 40 kg to 100 kg sample. An alternative is the single-stage GRG test (SGRG), which is generally based on a 20 kg sample. Experience has shown that GRG values can vary throughout an orebody, particularly within different grade and/or mineralogical domains. Test programs must consider sample frequency and mass. This study demonstrates the variability of GRG results based on different sample masses. Consecutive underground faces on a coarse-gold dominated quartz vein were sampled taking five different masses from each. Each sample was processed using a SGRG approach. Subsequently, each development round was batched through a small gravity production plant. The results show that the small samples understate the plant GRG and show inter-sample variability. Large samples show less variability and a SGRG closer to the plant GRG. A high SGRG broadly correlates to higher gold grades, more coarse gold and larger gold particles. These results are intuitively correct, but indicate the likely challenges of sampling for gold recovery in heterogeneous systems.CITATION:Dominy, S C, 2013. Variability of gravity recoverable gold values in relation to test sample size, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 293-302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

The purpose of this study is to formulate practical guidelines for active underground mining in close proximity to water bodies. This was accomplished through systematic completion of three phases of study: I) Collection and Documentation of Data; II) Application of Existing Guidelines to Case Histories of Previous Inundations; and III) Development of Recommended Guidelines for Underground Coal Mining Near Bodies of Water. Phase I of the study involved a worldwide data collection effort designed to obtain foreign and domestic guidelines for mining near water bodies, and accident records and case histories of accidental mine inundations. Within Phase II, existing guidelines were categorized and classified and then evaluated as to their effectiveness in precluding past inundations had they been in effect at the time of inrush. Advantages and disadvantages of existing guidelines were defined. Drawing on the broad data base established in previous study efforts, Phase III was directed at development of viable guidelines to promote the greatest possible coal extraction while precluding accidental mine inundation. Two levels of guidelines are presented; Level I Guidelines require little or no subsurface exploration on the part of the mine operator, while Level II Guidelines recommend various testing and investigative procedures to permit greatest possible mineral extraction. This report presents findings and conclusions of the study.

Jan 1, 1976

By John Murray, Daniel Ebin, Robert Gould

The Atlanta Plane Train project at Hartsfield-Jackson Atlanta International Airport employed the progressive design-build approach. This provided opportunities for collaboration between the design-builder, design engineer, and owner and the implementation of innovative design and construction approaches. The innovations have reduced risks, allowed for adjustments during design to accommodate new challenges, and provided open-book cost and schedule evaluations. The progressive design-build approach has also allowed for pricing of work to occur in phases—capturing the design/construction challenges as the project evolves and when they are more clearly defined. While this has allowed for pricing to be performed with better project understanding and therefore less contingency, the associated time frame for approvals has required careful consideration to avoid impacts to the schedule. This paper discusses the benefits and challenges of the progressive design-build approach.

Dec 1, 2022

By Robert J. Dompe

The objective of this program was to develop a cost effective microprocessor-based electronic image sensor system for monitoring pit slope displacement to detect and/ or predict impending slope failure in surface mines. A background study and data analysis yielded a performance specification for candidate Video Slope Monitoring Systems. A design concept was developed based on using a pair of solid state video cameras located on precision pointing assemblies. The digital images from the cameras are compared and, using electronic triangulation, slope topology is calculated. The current and past locations of operator selected features are compared to determine pit slope displacement. A proof-of-concept test was performed using a laboratory model of a pit slope. Based on the successful results of that testing it is recommended that an in-mine evaluation be performed using a full-scale prototype Video Slope Monitoring System.

Jan 1, 1982

By James L. Eirls

Tracor MBA under a contract to U.S. DOI Bureau of Mines designed, developed, fabricated and demonstrated a conveyor belt service machine. It is self-contained, battery powered, rubber tired and capable of handling, storing and transporting conveyor belting, wire rope and associated structures for sectional conveyor belts. While moving the tail section to its next position the machine discharges the belting, wire rope and belt structures. The belting is elevated and separated to provide for the insertion of the structures with minimum expended effort. A hydraulic system provides the power for steering, braking, winding or unwinding under controlled tension the belting and wire rope, operating a load-bed slat conveyor, raising, lowering and locking connection hitches and powering external hydraulic tools. Also, a pneumatic system is available to operate air impact tools. The service machine, with its present components can function in coal seams as thin as 48 inches, double wind conveyor belting 42 inches wide, 400 feet long, load or unload 3/4" wire rope on two separate reels and is controlled by two operators. A complete belt move using this machine requires only four workers. Successful underground demonstrations were conducted in coal mines located in West Virginia and Kentucky.

Jan 1, 1983

By E. D. Palmes

This report was prepared by New York University Medical Center, Institute of Environmental Medicine, 550 First Avenue, New York, New York under USBM Grant Number G0133066, Personal Samplers for CO, NO and NO2 in Air. The grant was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of the Pittsburgh Mining and Safety Research Center with Dr. George H. Schnakenberg acting as the Technical Project Officer. Mr. L. Young was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this grant during the period 3/1/73 to 11/30/76. This report was submitted by the authors in March, 1977.

Jan 1, 1977