Search Documents

By S. D. Viljoen

The use of ceramics to protect equipment subjected to wear in abrasive and corrosive applications has been accepted by most plants as the industry norm. Little is, however, known about alternative special ceramic based products which are available for the protection of plant assets. With careful engineering, impact resistant ceramics can be used in high impact zones using modern ceramic technology. Properly selected and properly installed, ceramics will provide a tough wear resistant lining for protection against abrasion and impact. Basalt, on the other hand, is widely used in coal washing plant process pipes with varying degrees of success. Basalt is normally not used for the lining of bends, ?T? pieces or reducers due to the reduced wear resistance compared to alumina ceramic. The advantage is a much reduced initial capital cost. A patented ceramic composite non-return valve solved an old problem encountered in the operation of medium sumps. The design approach overcomes the lack of functionality of alternative designs and reduces valve wear while preventing medium settlement during plant shutdown periods. Direct bonded ceramic pulley lagging is becoming the industry norm, eliminating most of the problems encountered with conventional pulley lagging systems.

Jan 1, 2010

By W. T. Swensen

The Anaconda Company, through its wholly owned subsidiary The Anaconda Company (Canada) I,td., has investigated, optioned and partially developed a large tonnage of iron ore amenable to magnetic concentration. The reserves are located in north central Ontario and occur within a twenty-two mile belt of layered and intricately folded metamorphic rocks, close to the north contact of an igneous complex of granite and pegmatite. There are two main ore deposits. Briarcliffe is a steep to vertically dipping body 100 to 500 feet wide and over a mile long. The Two Mile Lake deposit is flat dipping and confined to an open, asymmetrical syncline; it is approximately a mile wide and 250 to 4.00 feet thick. On its flat easterly plunge, it is saucer-like in shape and is amenable to open-pitting for an east-west distance of several thousand feet. Magnetometer surveys, confirmed by drilling, indicate at least a three mile eastward extension of this deposit. Location and Access: The property is located in the Kowkash Mining District of northwestern Ontario, roughly forty-four miles north of the community of Nakina on the main line of the Canadian National Railroad. (Fig. 1) Access during the exploration period was entirely by airplane from Nakina. (Fig. 2) More recently, Nakina itself was connected to the highway network in the Longlac-Geraldton area. The property is roughly 190 miles by existing and proposed railroad from the Great Lakes waterway system. The Trans-Canada pipeline moving natural gas from western to eastern Canada passes through Geraldton roughly 70 miles south of the property. Topography: The surface features in the area are typical of a sizeable portion of the Precambrian Canadian Shield area. Many lakes, low swampy areas, and glacial moraine-type features are common in this recently glaciated area. The average elevation is between 800 and 900 feet above sea level, and the relief is probably less than 100 feet with the greater portion of the area less than 50 feet. The topographic "highs" are formed either by outcrops that were resistant to glacial erosion or by moraines, eskers and drumlins which were deposited upon the recession of the glaciers. The better mineralized zones, composed chiefly of quartz and magnetite, commonly form ridges resistant to erosion and weathering. Previous Work: Because of the obvious outcrop of the magnetite-rich beds and knowledge gained from early developments within the general region, it is conceivable that the presence of the iron formations has been known for a good many years. The area is included in studies made by L. F. Kindle* in 1929 and 1930 for the Ontario Department *Kindle, L.F., Kowkash-Ogoki Gold Area, Ontario Department of Mines Annual Report, Vol. XL, Part IV, 1931; map 40f

Jan 1, 1961

By Trevor R. Ellis

The extractive industries addition to the International Valuation Standards (IVS) is scheduled for publication in the next edition of the IVS book in January 2005. This will provide guidance for valuation of minerals and petroleum industry assets of all types for all appraisal uses. It will provide asset valuation support to the International Financial Reporting Standards for the stock markets of the world, and a global umbrella standard which can be supplemented for local needs by institutes and regulators. This paper discusses implementation of the IVS within the minerals industry and important issues that the industry should confront.

Jan 1, 2005

By Sanjay Kumar Singh

The mechanics of load transfer in bord-and-pillar mining is not well understood despite the evolution of the art of pillar extraction over the last 20 years via trial and error (empirical) or Rock Mass Rating (RMR), simple monitoring and pillar extraction experiences at neighboring mines. Variations in geologic conditions and pillar extraction methods, along with a lack of comprehensive instrumentation programs for monitoring ground behavior during pillar recovery, are among the factors that make it difficult to predict how strata will respond to pillar extraction. Efficient and safe use of roof supports depends on the interaction between the designed support and coal strata. Of particular interest in this study is the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods and optimum support with load-bearing capabilities in strata control during mass exploitation of underground coal deposits required detailed investigation,?. To provide a better understanding of the mechanics of strata deformation, as researchers, we have collected data and reviewed measurements of convergence and stress in one mine of South Eastern Coalfields Limited (S.E.C.L.), i. e., in North Chirimiri Pondary Hills (NCPH) and have completed numerical modeling with FLAC software for (Fast Lagrangian Analysis of Continua modeling, Itasca India Consulting Pvt. Ltd.) for two typical pillar extraction plans. Stress distribution in the mine roof above pairs of roof supports was calculated to demonstrate how Resin roof bolt support installed support contributed to roof block movement control. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal measure rocks and by pillar extraction sequences and layouts. Also, resin roof bolts and other support systems play a critical role in controlling stability of both the immediate roof and the main roof for a distance of up to 18 meters (i.e., working coal seam height X three times) above the seam. Installed supports provide unique strata control advantages over other types of secondary support by significantly reducing the time between mining and installation of the secondary support. Although resin roof bolts are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at nearpeak capacity(Singh, et al., 2006), whereas posts fail and lose their ability to limit mine roof deformation.

Jan 1, 2012

By J. A. Meech, R. J. Tucker

"Since the establishment of froth flotation as an effective method of mineral beneficiation there has been both academic and industrial interest in the levels of the various reagents required to perform the desired separations. Academic interest was spurred by a desire to understand the mechanisms involved - industrial interest by a need to improve the efficiency of the process. These efficiency improvements can take two forms: cost reductions due to reduced reagent consumption and/or improved separation efficiencies. The latter are indicated by either improved grade-recovery relationships for removal of a valuable mineral from gangue, or improved separation of two similar valuable minerals.The processing of lower grade ore bodies at higher tonnage rates has necessitated increased interest in both reagent consumption and metal recovery. Furthermore, the development of accurate and functional on-stream analysis equipment in the 1960's and 1970's has allowed for a better understanding of the dynamic processes involved in a flotation circuit and has required a more concrete statement of the relationships and reactions between the minerals and chemicals in the flotation pulp. Development of these relationships is necessary in order to make use of on-stream analysis to control the process at, or near its more efficient level."

Jan 1, 1984

By Nolan Eckroade, Nigel Pereira

Wireless electronic blasting systems are a new technology that enable truly wireless initiation through rock, air and water. This is achieved using low frequency magnetic induction waves to wirelessly send a firing command to groups of in-hole primers. Fully wireless initiation not only removes the limitations imposed by a wired connection to each primer in a blast, but also enables users to alter the paradigm of conventional mining techniques to advance operational productivity and reduce personnel exposure to high-risk activities. While initially deployed in underground applications, wireless electronic blasting is now being used in the open cut environment. To capture the early impacts in surface mining operations, case studies conducted at three surface mines evaluated blasts utilizing a wireless electronic blasting system against baseline blasts using conventional, wired initiation systems. The purpose of this paper is to outline the specific learnings associated with wireless electronic blasting in surface mining to date. The paper will include references to these specific case studies as well as benefits realized and applications for the future.

Multilevel-multiseam hardcoal mines on the European continent usually consist of a huge network of underground openings, sometimes more than 200 km long in total, with some longwalls operating down to a depth of 1,500 m. While operating several longwalls simultaneously, these mines are making use of a number of stationary and mobile measurement- and analysis units in their main ventilation passes combined with atmospheric measurements on the surface. This paper provides an overview over the systems and technology used and describes the typical set-up of a measuring net. To detect and monitor underground fires through fire gases measurement and -analysis, a mobile underground testing laboratory collects data locally in the area of the fire. These laboratories have proven to be extremely useful not only during the actual fire fighting but also for the long-term gas measurements in critical mine areas. They have repeatedly detected starting fires and have thus given the mine the opportunity to react early and to avoid larger damage. Therefore several mobile laboratory units have now been installed for long-term testing in a number of German mines and similar units are being used in the Czech Republic and Poland.

Jan 1, 2012

By R. Stefanko

This Final Report covers the work performed for Contract No. H0377043, "Cables for Face Equipment" from August 1, 1977 to April 1, 1981. It reports the findings in three areas of research: cable protection, circuit-breakers, and high-voltage cable couplers. Laboratory and analytical studies have been conducted in the three areas to determine proper circuit-breaker settings, cable sizes, and coupler performance. Also, an extensive field-monitoring program was established to relate in-mine epxerience to laboratory findings. Further, various pieces of equipment was designed for laboratory testing, particularly in the area of cable reeling and unreeling.

Jan 1, 1981

By C. Keefe, O&apos

Measurements of the quantity of entrained air within processes have challenged instrumentation developers for years. This is particularly true in the unique and demanding operating environment and applications seen in minerals processing. In minerals processing applications, entrained air plays a role in errors seen within nuclear density gauge measurements and in pumping efficiency. It is also the major component of flotation processes. The measurement of the quantity of entrained air, known as the gas void fraction, can now be performed from the outside of a process pipe through CiDRA?s patented passive sonar array-based technology. Within column cells, the need for a robust, no maintenance, accurate means of measuring the entrained air, known as gas holdup, has resulted in a submersible version of this technology. CiDRA?s meter technology calculates the gas void fraction by first measuring the speed at which naturally occurring sound in the process slurry propagates past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. A known relationship between this speed of sound and the entrained air captured in the form of bubbles within the slurry is then applied in CiDRA?s meter to calculate the gas void fraction. This paper will present the measurement technology, its operation, its calibration and its application in a variety of gas void fraction and gas holdup measurement situations such as pumping efficiencies, hydrocyclone operation, external sparging, and column cells.

Jan 1, 2008

By Thomas Varley

IN THE congressional act establishing the Bureau of Mines one of the functions outlined was "to assist I the industry in the prevention of mineral waste." This had not only to do with the waste in mining but in milling and metallurgical practices, including smelting. The organization of the Bureau of 'Mines includes many divisions, each working in a particular field and charged with certain investigative work. The metallurgical division has the above duties under its immediate supervision, and the station located at Salt Lake City is directed by the chief of this division: There are ten experiment stations of the Bureau of Mines, located in various parts of the country, most of them being housed at state universities under cooperative agreements. Considerable care was exercised in locating the stations and in choosing the particular type of work to be investigated at each place. Inasmuch as the Bureau was designed to serve and cooperate with the industry it is only natural that the investigative work be of interest and importance to the territory immediately adjacent to the respective stations.

Jan 1, 1925

By Xiangxi Wu

Longwall and continuous mining are prevalent methods employed by Chinese underground coal operations. The main ground control challenges include roof skin deformation, roof collapse, and outbursts of coal, gas, and water. Microseismic monitoring provides valuable information on rockmass behavior and fracture propagation caused by stress redistribution, active geological structures, or gas build up within the coal strata and the surrounding rockmass. Collecting and assessing seismic data has proven to be an instructive tool for engineers to better assess ground conditions and mitigate seismic hazards associated with mining. The development of intrinsically safe and explosion proof certified seismic monitoring equipment has revolutionized China?s underground coal mines. The use of this technology allows for the optimization of gas drainage at an increased rate of two at a 50% higher purity without any increase in drilling costs. Microseismic monitoring can also be used in identifying seismically active faults and shear zones. This information can be used to assess and revise mining strategies to improve safety and ground stability.

Jan 1, 2012

Process Options for Difficult Arid-Region Nickel Laterites In the absence of the discovery of significant nickel sulfide deposits, the future of Australia's nickel industry will increasingly depend on cost effect processes for low-grade nickel laterites. The problems encountered with the West Australian HPAL plants, resulting in three of the four plants being shut down, have caused the industry to revisit atmospheric leaching options, particularly heap leaching. West Australian laterites are characteristically very varied in grade, chemical composition and mineralogy with the result that, thus far, one process does not fit all laterites. In this paper the leaching of an especially refractory ore is compared using column leaching of whole ore and atmospheric leaching and HPAL processing of ground ore. The key characteristic is the resistance of the goethite phase to acid attack with low-to-moderate temperature leaching conditions. The refractory characteristic is attributed to the stabilising influence of chromium and aluminium and possibly manganese substitution in the goethite crystal structure and goethite morphology. A significant three-fold increase in both nickel and cobalt extractions under atmospheric leaching conditions was achieved by the relatively simple modification of bubbling sulfur dioxide into the reaction vessel to create a reducing environment. Recoveries increased from <30 per cent to 90 per cent nickel and 86 per cent cobalt after 10 hours of leaching at 95¦C. An even greater improvement was achieved under ambient conditions by heating the ore to temperatures above 250¦C for 30 minutes. Subsequent leaching at ambient temperature gave an eight-fold increase in both nickel and cobalt recoveries after 14 days bottle rolling. Both methods could be optimised and implemented in such a way as to increase laterite reserves in conjunction with a heap leach operation but may be better suited to vat or closed tank processing.

Sep 13, 2010

By Ana E. Bohé, Georgina De Micco, Juan P. Gaviría, FEDERICO J. POMIRO, Gastón G. Fouga

Chlorination and carbochlorination processes have industrial applications in metallurgical activity for extraction and purification of uncommon metals such as rare earth elements (REE). This study reviews the chlorination and carbochlorination reactions of light REE (LREE) oxides with chlorine considering the thermodynamic, stoichiometric, and kinetic aspects of the reactions. Lanthanides between lanthanum to gadolinium were considered as LREE, in agreement with previous literature, and the results were detailed in this review. LREE were analyzed taking into account their oxidation states and were divided into three groups accordingly. The results presented show that, although the LREE are chemically similar, their behaviors during the reactions with Cl2 and Cl2–C, and the different LREE-O–Cl compounds formed, have particularities. It was observed that gadolinium, in both thermodynamic calculations and experimental results, presents some differences, and it can be considered intermediate between light and heavy REE; i.e., reactions between LREE2O3 and Cl2(g) begin at approximately 250 °C, except for Gd2O3 that begins at 327 °C. The present work will contribute to a better understanding of the chemistry of LREE oxides and Cl2 under different conditions and the products obtained in the LREE–O––Cl2(g) and LREE–O–C–Cl2(g) systems.

Oct 15, 2021

By David H. Sanders, Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Large-diameter drilled shafts (DS) are a critical part of a seismic-resistant system, and therefore it is important to be able to accurately model lateral resistance. To undertake the lateral load analysis of largediameter DS, a finite-difference p-y analysis program, NVShaft, is being developed at the University of Nevada Reno. Validation of the new program involved numerous p-y analyses using commercially available programs. Subsequent comparisons suggested the program's ability to yield reasonable predictions for typical diameter DS. Based on the I-15/US 95 load test program carried out in Las Vegas, NV, this study presents the evaluation of NVShaft in Nevada’s subsurface condition. Lateral load analyses of a 2 ft and an 8 ft diameter DS were attempted using NVShaft. The location of the applied lateral loads and the presence of cemented soil-layers were incorporated in the modeling. A good agreement between NVShaft prediction and the measured response was found for the 2 ft diameter DS. For the 8 ft diameter DS, a stiffer response was predicted. The inspections of the moment-curvature characteristics at different load levels suggested cracked response of the concrete due to prior axial load testing may be one of the reasons behind the deviation.

By M. Yavuz

One of the challenging problems for optimization in mining operations is to choose the best equipment among the alternatives. Equipment selection is an important task for mine management due to its operational cost, and is also an integral part of mine planning and design. Equipment selection is not a well-defined process because it involves the interaction of several subjective factors or criteria. Besides, decisions are often complicated and may even embody contradictions. Therefore, equipment selection is considered as a multi-criteria decision-making process, and suitable decision-making methods should be employed in this process. In this study, the loader selection for Aegean Lignite Colliery was made by using both the analytic hierarchy process and Yager’s method. Owing to the misusage of Yager’s method in the past, a new procedure is proposed in this paper for making proper decisions. It is highly recommended in this purposed method that criteria or alternatives should be grouped so as not to exceed the limitations of human performance (nine criteria/alternatives). The most appropriate solution for the loader selection was investigated by obeying this limitation for each method, and the results were compared. At the end of the decision-making process, a sensitivity analysis was applied for each method in order to see how a criterion affects the final decision. The advantages and disadvantages encountered during the application of each decision-making method are presented.

Jan 1, 2015

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) superjacent mines, subsidence and caving propagating to overlying seams and ii) mines, pooled water and the potential for inundation resulting from a iii) breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, the presence of overlying or underlying mine workings where iv) pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist. The planning and engineering design considerations associated with each case history is presented along with geotechnical information. In the case of the highwall collapse a back analysis is presented of the stability and safety factors for the auger webs, highwall miner web pillars, and barrier pillars.

Jan 1, 2009

By P. L. Woolf

Blast furnace coal injection tests conducted by the Bureau of Mines in cooperation with a consortium of 22 steel companies in 1963-1964 are described. These tests were part of a program of extensive investigation of auxiliary fuel injection in the Bureau's experimental blast furnace located at Bruceton, PA. Seventeen coal tests are described on various coals ranging from anthracite to subbituminous. Factors affecting maximum rates of injection were studied. These included coal size, coal type, and oxygen enrichment. The effect of high sulfur content coal and the means to control metal sulfur were investigated. An epilogue briefly describing the commercial experience with coal injection from 1960 to the present has been included.

Jan 1, 1985

By C. Demir, M. S. Celik, I. Gülgonul

Na-feldspar (albite) and K-feldspar (microcline or orthoclase) are major feldspar minerals with identical crystal structures and physicochemical properties. Flotation appears to be a unique method of separating these minerals. Fundamental studies on amine/feldspar system in the presence of monovalent salts showed that separation of these feldspar minerals by flotation is possible at certain concentration of monovalent salts in HF medium and natural pH. A comparison between natural pH and HF medium indicates that the latter provides a better selectivity at the expense of higher collector requirement. A general mechanism for both systems involving an ion exchange between the uncommon ions and adsorption of the common ions is proposed to be responsible for creating differences in the charge of albite and microcline unto which amine adsorbs.

Jan 1, 2002

By Joe Zhou

"Mineralogical characterization and metallurgical extraction of silver is challenging due to its complex mineralogy and chemistry. Over 200 Ag-bearing minerals have been identified and a silver-rich ore body would typically contain 5 to 10 different silver minerals. Silver can occur not only as discrete microscopic (visible) silver minerals but also as submicroscopic (invisible) silver in other minerals. During processing, silver may form passivation compounds such as silver hydroxide, silver sulphide, jarosite-like silver sulphate, silver halide or silver cyanide precipitate, all of which may negatively impact on silver extraction. Knowing the deportment of silver in the ore and its metallurgical products is important in flowsheet design and plant optimization. This paper begins with the classification of silver ores and minerals and a review of processing techniques, and focuses on the major mineralogical factors to explain why and how these factors affect silver extraction. Case studies are provided to demonstrate the application of silver process mineralogy in flowsheet design and plant optimization.INTRODUCTIONSilver was known to and utilized by mankind since ancient time. Actually, it was one of the earliest metals discovered and utilized by mankind after gold and copper.Silver is the whitest metallic element. It is rare, strong, corrosion resistant, and unaffected by moisture, vegetable acids, or alkalis. Silver is also resonant, moldable, malleable, and possesses the highest thermal and electric conductivity of any substance. The chemical symbol for silver is Ag, from the Latin argentum, which means white and shining. Although silver does not react with many chemicals, it does react with sulfur, which is always present in air at trace amounts. The reaction causes silver to tarnish, and consequently it must be polished periodically to retain its luster.Silver possesses many special physical characteristics and qualities that make it useful to a variety of industries. The photography industry is the biggest user of silver compounds. Silver forms the most light-sensitive halide salts, which are essential to developing highquality photographic prints. Silver also has the highest electrical conductivity per unit volume of any metal, including copper, so it is used extensively in electronics."

Jan 1, 2010