Search Documents

By Timothy M. Bruner, William J. Maloney

Faced with rapid growth that strained their current water supply capabilities, the Somerset Water Service in Somerset, KY decided to construct a new intake structure on the shore of Lake Cumberland. With an existing intake structure within 200', very hard limestone geology with calcite geodes, and lake level fluctuations as high as 50 ' ,this project posed many challenges. The following paper discusses how mechanical excavation techniques were used to overcome these obstacles.

Jan 1, 2001

By Jeffrey M. Listak

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By W. H. Langer

Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

Jan 1, 2009

By Ali Kahriman, Alper Celtikc, Serdar Celik, Tuncer Gungor

This paper presents the results of ground vibration measurements carried out in Gülyali Hisarcik Basalt open pit mine located on the north side of the Anatolia near Ordu province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 5 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 5 different vibration monitors (4 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2013

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines on the spontaneous combustion of U.S. coals. Approximately 11 pet of U.S. underground coal mine fires are attributed to spontaneous combustion. The relative self-heating tendencies of 24 coal samples were evaluated in an adiabatic heating oven. Minimum self-heating temperatures (SHT's) in the oven ranged from 350 C for a lignite and high-volatile C bituminous (hvCb) coal, to 1350 C for two low-volatile bituminous (lvb) coals. An empirical expression was determined predicting a bituminous coal's minimum SHT in the adiabatic oven based on the coal's dry ash-free oxygen content. Several factors that can affect the self-heating process were also evaluated. The self-~eating tendency of a coal increased when the coal was dried and exposed to humidified air, and was dependent on the particle size and oxygen concentration of the air. A new moderate-scale apparatus is described, in which the self-heating tendencies of larger coal samples, 3 kg, can be evaluated. The minimum SHT's of two coals were determined and the results were in good agreement with those found in the adiabatic oven. Finally, results of a test in the moderate-scale apparatus indicated a strong dependence of the self-heating rate of a low rank coal on the moisture content of the air.

Jan 1, 1987

By J. A. Pile, Virgil Miller, R. G. Peterson, F. B. Petermann

"INTRODUCTION As virtually no published data are available on the sintering of fine, minus-100-mesh, ferrograde manganese ores, it is most opportune to present data on the amenability of various fine ores and mill products to the sintering process. These data cover the sintering or nodulizing of finely crushed, high-grade pyrolusite and rhodochrosite ores, sintering of manganese carbonate flotation concentrate, sintering or nodulizing the calcine from the deleading of a manganese oxide flotation concentrate, and sintering the calcines made in a Herreshoff furnace from the treatment of manganese sulfate products.If finely sized products are to be smelted in the present electric or blast ferromanganese furnaces, they must be sintered or nodulized. The only specification as to the size of the sintered or nodulized product is that it must pass a 6-inch screen and not contain over 1t-1/2 percent minus 20-mesh material. The minimum-maximum size has not been established. Undoubtedly this opti mum size will be set by the ferromanganese industry when ample quantities of manganese oxide sinters have been smelted."

Mar 1, 1942

By Thomas A. Davidson

The Bureau of Mines Helium Field Operations has developed a simple and accurate method for calculating the viscosity of gas mixtures. Only the composition of the mixture and the molecular weights and viscosities of the pure components in the mixture are required. The momentum fraction of a mixture is calculated from the composition. The fluidity is calculated as a quadratic function of the momentum fractions. The efficiency factor for transfer of momentum in collisions between bodies of different masses is derived and used with one empirical constant. The viscosity is the reciprocal of the fluidity. Results of the method are compared with 752 reported viscosities for 40 dilute binary systems at temperatures from -78 to 276.9°C. Using this method the average absolute deviation is 1.29%, the root-mean-square deviation is 1.99%, and the average deviation is -0.84%.

Jan 1, 2010

THERE are certain facts that the mining industry in Australia is faced with at the present moment which may be accepted as axioms. The industry is at a low ebb, as evidenced by statistics. Metals form the basis of all modern industries, and are necessaryfor the welfare of Australia. Mining is a wasting asset. Every ton of ore extracted is one ton less which c.annot be made good, and it should be our duty to get as much profit froin that ore as possible, otherwise there is a permanent loss to the country.The metal market cannot be controlled by Australia; it is more or less an international matter. Australia has not been thoroughly prospected. There are no mines being developed that are likely to replace those which are being depleted.Our mining engineers are as capable as those in other parts of the world, and have made good where they have been given a chance. There is no one cause for the present depression; there are several, more or less, interwoven. Of course, the war has had an adverse effect, but that has only dislocated things temporarily; it upset our markets, influenced the price of metals, and affected the labour market and cost of stores. Labour troubles made their appearance before the wave of unrest swept over the world. The cause of labour discontent must be investigated, and if possible removed. As each industry has .its·own problems, miners must inquire into their special problems, as there is no sovereign remedy that will suit all cases.It is obvious that we cannot mine ore if we do not know where it is; therefore, the first thing is to discover workable deposits.

Jan 1, 1919

Formation of either sodium jarosite or lead jarosite from concentrated chloride solutions containing small concentrations of sulphate has been demonstrated. Sodium jarosite is precipitated at 95-100°C from FeC13-FeCI2-NaCI-PbCI2 solutions to which was added Na2SO4 or Li2SO4 in amounts greater than 0.05 M. In the absence of alkali metal ions capable of forming jarosites, lead jarosite was precipitated from either FeCI3-PbCI2 or FeCI3-FeCI2-LiCI-PbCI2 solutions to which had been added small amounts of sulphate. Many of the factors affecting jarosite precipitation from chloride solution have been elucidated, and the most critical were sulphate concentration and initial pH. Concentrations of HCI in excess of O. I M essentially suppressed the production of jarosite in chloride media. Alkali jarosite, precipitated in the presence of dissolved lead, incorporates a small amount of this metal into the alkali jarosite lattice. Small but significant amounts of copper can also be incorporated into alkali jarosite and the amount is further increased in the presence of lead. Other divalent base metals such as Zn, Cd or Ni are not significantly precipitated. Sulphate control in either FeCI3 or FeCl3-NaCI leaching systems could likely be maintained by jarosite precipitation provided that the acid concentration of the solution was low.

Jan 1, 1981

By Stephen A. Swan

Bureau of Mines researchers have collected and evaluated rollover protective structures (ROPS) f or more than 10 yr. ROPS and falling object protective structures (FOPS) are required on specified mining machines under regulations of the Mine Health and Safety Administration (MSHA). Both ROPS and FOPS are required on mining machines used in surface coal mines and surface areas of underground coal mines (30 CFR 77.403 and 7 7.4 13a), and ROPS are required on mining machines used in metal and nonmetal mining operations (30 CFR 55, 56, and 57.9-88). This illustrated manual provides mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check- list for inspecting ROPS being used in the field. The manual discusses specific requirements of the MSHA regulations and minimum inspection and maintenance checks for ensuring compliance with those regulations. An easily reproducible checklist is provided as an aid to the inspection of ROPS.

Jan 1, 1985

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By Masaki Kitazume

Deep mixing method, in-situ admixture stabilization technique, has been developed and adopted for on land and marine construction works in Japan. The geotechnical design procedure of the method has been standardized in Ministry of Land, Infrastructure and Transport Government of Japan for port and harbor facilities, which includes the block type and wall type improved grounds for foundation stability, settlement reduction purpose. This procedure is based on the allowable stress concept, in which the induced stresses within the improved ground are confirmed to be lower than the allowable strength in the internal stability calculation. This procedure has been cited by several organizations to establish their standards. The Ministry has a plan to introduce a reliability based design for marine construction works in 2006, in which the design procedure on DM improved ground will also be modified to the reliability based. In the new design procedure, the average and variation of soil parameters and external loads are incorporated by partial safety factors to investigate the stability of improved ground. According to the plan, the author has been studied the design procedure and the magnitude of partial safety factors, and has established a preliminary draft of the standard. This draft will be brushed up through comparing the current design procedure. In this article, the design concept and design procedure of the method are briefly described.

Jan 1, 2004

By J. Geisler

When addressing Germany’s resource supplies, we need to distinguish between those domestically available and imported ones. Resource extraction ostensibly competes with the designation of protection areas. However, the parallel existence of wildlife and plant life, and operations in the areas used for resource extractions is continually underestimated. The European Commission has compiled guidance documents facilitating the extraction of resources from protected areas. With regard to resource productivity, the market appears to be the appropriate instrument for minimising resource consumption. Policy makers are now called upon to create a legal framework leading to a consensus accepted by society.

Jan 1, 2011

By Omid Lashkari

Keywords: SEED, SSM materials, Microstructural evolution, Rheology, Swirling Speed SEED (Swirled Enthalpy Equilibration Device) is established itself as a new technology amongst the many Semi-Solid Metal (SSM) processes, where swirling of the mush plays an important role in modifying the dendritic structure of as-cast parts. A range of semi solid metal structures, dendritic, rosette and/or globular morphology of primary phase, can be prepared using SEED. The current article reports on the application of rheological tests in characterizing microstructural evolution during SSM processing of 356 Al-Si foundry alloy. A simple parallel plate test machine, designed and constructed at our labs, was used to determine viscosity values for each structure and identify the optimum structure with superior die filling characteristics. Such findings have important technological and economical implications during high pressure die casting of semi- solid metals. The strain-time graphs for 356 Al-Si foundry alloy indicated lower viscosity values for globular microstructure, i.e. improved die filling.

Jan 1, 2005

Edward Keller, Baltimore, Md. (communicatioin to the Secretary*):—It is pleasing to note the increasing amount of work on metallurgical problems that is being carried on by exact scientific methods, and the results of such labor issued by the laboratories of our universities. Without doubt, Mr. Bolles's paper will be welcomed by all progressive practitioners. Many of the results which Mr. Bolles presents to as are new; and I take exceptioil to a few minor points only. The first of his concluding remarks is as follows: "Mattes are not homogeneous, but are composed of distinct mineral entitier, and may be likened to igneous rocks, in which the mineral constituents fall out upon the lowering of the temperature and ensuing solidification." He quotes an introductory remark to a paper1 of mine, as follows: "The true chemical character of copper-mattes does not yet seem to have been definitely determined, i.e, it is still more or less of an open question whether they are true chemical compounds, or mixtures, such as igneous rocks." This quotation, taken alone, would convey the impression that Mr. Bolles's conclusion is entirely new. Had he quoted also another paragraph from my paper in question, it would be clear that he was, to a certain extent at least, anticipated. I take the liberty, therefore, to state the substance of my own work. In the paper referred to, I showed the existence of the phenomenon of liquation in mattes, and, continuing, said: " A more direct method to test whether a matte is a compound sulphide or a mixture of individual sulphides was attempted by applying hydraulic separation. A clean piece of matte was selected containing practically no magnetic oxide and of the following composition: Cu, 37.96; S, 24.45; Fe, 33.63; Zn, 1.25; Pb, 1.02 ; Sb, 0.26 ; As, 0.065 ; insoluble, 1.15 per cent. ; Ag, 26.7 ; Au, 0.04 oz. per ton. For such a test it is essential to select a chemically uniform piece, other-

Jan 1, 1905

By R. August Heindl

A process for recovering manganese from open-hearth steel-plant slags was investigated. The proposed method of accomplishing this is indicated by the flow diagram in figure 1. Mixtures of open-hearth, steel-plant flush slags and limestone, so proportioned as to have molar [CaO -3P205] ratios of approximately 2, were fired at approximately 2,400° F. in an oxidizing atmosphere and then cooled slowly. This treatment produced a clinker consisting principally of two solid phases comprised of (1) various combinations of the oxides of manganese, iron, aluminum, and magnesium, probably in spinel complexes, and (2) a dicalcium silicate phase, which contains the phosphorus. Reduction of these clinkers with hydrogen or with gaseous mixtures containing CO, CH4, and other hydrocarbons at about 1,300° F. formed manganous oxide as well as varying amounts of ferrous oxide and iron. Carbon monoxide and mixtures of hydrogen and carbon monoxide effectively reduced the clinkers but also gave higher proportions of soluble iron when the manganese was extracted from the reduced clinkers by leaching at about 80° F. with ammonium carbonate solutions containing 26 to 28 percent ammonia and 15 to 26 percent carbon dioxide. It is believed that the manganese is in solution as an ammonia-manganese complex. Concentrations of about 90 grams of manganese per liter were obtained by batch countercurrent procedures. By distilling 50 percent of the ammonia, the ammonia-manganese complex was decomposed, and approximately 90 percent of the manganese was precipitated as the carbonate with the simultaneous precipitation of 15 to 30 percent of the iron, the larger amounts of iron precipitating in the continuous tests. The manganese-iron ratio in the product could be increased either by recycling more manganese from the distillation to the extraction or by aerating the liquor to purge it of iron before, rather than after, the distillation step. Calcination of the pelletized manganese carbonate in an oxidizing stmosphere at 2,000° F. or above gave a final product, Mn304, resistant to crushing and apparently possessing the other physical properties essential in a ferromanganese blast-furnace feed.

Jan 1, 1955

The Effects of Collector and Grinding Environment on the Flotation Selectivity of Rosh Pinah Pb/Zn Ore

Sep 13, 2010

By William C. B. Gates

Demolition blasting next to an active railroad can be very challenging because of track safety, blasting vibrations, potential track fouling by blast debris, and short work windows on a live track. Recently, in eastern Washington, one of the major railroad companies has been aggressively constructing a second main track to accommodate the expected increase in rail traffic of natural resource products. To accommodate construction of the second line, the railroad company used blasting demolition techniques to remove an old railroad trestle pier on the Milwaukee Road that was in the footprint of the new track bed. The trestle bridged the present rail line and flanked the track with two massive 550-ton (499 tonne) twin-columned steel reinforced concrete piers. The railroad contracted with a specialized contractor to remove the south pier using blasting demolition techniques. The blasting design presented the following challenges: blasting during live track conditions and short work windows; designing a V-notch blast pattern to ensure the pier fell away from the live track; drilling, loading, and timing of the shot; maintaining blasting vibrations at the track below 4 in./sec (102 mm/sec); maintaining ambient overpressure noise below 133 dB; control of fly rock and debris; and track protection and emergency debris removal plan.

Jan 1, 2016

By David M. Gullikson

As part of its program of petroleum production research the Federal Bureau of Mines has long been engaged in the study and development of systems of analysis of oilfield waters (8, 12, 20, 21, 22, 27, 30).21 However, many of the early chemical procedures developed by the Bureau and widely adopted by the petroleum industry are time consuming, and some are unreliable for determining certain constituents found in California oilfield waters. Because of the need for more rapid and more accurate methods having greater sensitivity with low concentrations of some constituents, a study has been made by the Bureau's Petroleum Research Laboratory at San Francisco, in developing new techniques and modifying previously published techniques for analyzing oilfield waters by flame spectrophotometric, potentiometric, and colorimetric methods. Test solutions were synthesized for testing the suitability and accuracy of the procedures, and the effect of interfering ions. These solutions contained known quantities of characteristic constituents of oilfield waters including sodium, magnesium, potassium, calcium, lithium, strontium, barium, sulfate, chloride, bromide, iodide, carbonate, bicarbonate and borates in a wide range of concentrations. The compositions of these synthetic brines are listed in table 22. Many California oilfield waters contain salts of petroleum-derived organic acids and several synthetic oilfield waters also were prepared to which large quantities of naphthenates or salts of petroleum acids were added.

Jan 1, 1961

By W. E. Kuhn

Introduction The work, of which some of the results are described in this paper, was started with the object of investigating the properties of certain binary alloys of titanium made from powders. Our main interest was in the possible use of such alloys in gas turbines. We were attracted to titanium, as have been others, by its high melting point (I,724° ± 11°C.), its low density (4.54), and the likelihood that, if a relatively wide use could be found for the metal, it might become available in commercial quantities at a fairly reasonable price. The readiness with which the metal reacts with hydrogen, oxygen, and nitrogen was recognized from the very beginning. At the same time there seemed a good chance that alloys could be produced which, because of the formation of protective films, would resist the attack of these and other corrosive agents. No specifications were drafted to cover the 'quality' of the titanium hydride powder which was used in our work and which was, to judge by the results of a few preliminary experiments, the most useful source of titanium then (1944) available in sufficient amount for our purpose. During the course of our work, the need for such specifications became very clear (see Sections 9 to 12 of this pa per). Even today, lack of knowledge regarding the effects on titanium of impurities, some of which may later be looked upon as essential elements in commercial alloys of titanium, and difficulties in manufacture, make the preparation of specifications for commercial titanium and titanium compounds a doubtful procedure. The papers presented at the 1948 Symposium on Titanium, sponsored by the U.S. Office of Naval Research lend colour to this view. At the time our work was commenced, one had to depend upon the manufacturer to supply what he considered to be his 'best' material. It may be some time before we can ask for more than this, the question as to what is his 'best' being left to the manufacturer to decide. However, in this connection the results of our study may be of some value and on that account we are constrained to publish them.

Jan 1, 1950