Search Documents

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By 000-001-568

August 15th, 1871. THE Institute assembled in Packer Hall of the Lehigh University, the President, Mr. David Thomas, of Catasauqua in the chair. Professor Henry Coppée, President of the Lehigh University, made an address of welcome to the Institute, and placed at its disposal a convenient hall for purposes of meeting. Mr. Thomas tendered his resignation as President of the Institute, as advancing years prevented him from actively participating in its meetings. The Institute declined to accept the resignation, and, on the assurance that active duties would not be expected of him, Mr. Thomas was induced to withdraw it. Invitations were received from Mr. B. C. Webster, President of the Lehigh Zinc Company, to visit the mines and works of the company; from Mr. Charles Brodhead, to visit the Chapman Slate Quarries ; and from the Lehigh Coal and Navigation Company, to visit their works at Summit Hill and Mauch Chunk and the Nesquehoning Tunnel. The Council reported the names of persons already elected in the two classes of members and associates. The following resolutions were passed: Resolved, That a committee of three be appointed, who shall take into consideration the printing and publishing of papers originating with the Institute, and that a uniform system as regards size and execution be adopted. The committee appointed consisted of Messrs. R. W. Raymond, E. B. Coxe, and the Secretary. Resolved, That the Council design and prepare a seal for the Institute at the earliest practicable time. Resolved, That a committee of six, with power to add to its numbers, be appointed to examine into the question of the more economical production of iron in this country. The committee appointed consisted of Messrs. G. W. Maynard,

Jan 1, 1873

By C Adams

Reports of delays and cost blowouts in major study and construction projects are becoming increasingly prevalent in the resources industry. This is mainly being attributed to an escalating cost environment associated with the increased number of projects in the development to construction pipeline and a scarcity of competent skilled resources to deliver these projects. However, not all this effect can be directly attributed to the current environment. Historically the mining industry has not performed well in its ability to deliver projects according to the financial and physical parameters forecast in the feasibility study process. To manage the risks associated with delivery of major projects, resource companies need to ensure they use a standardised approach to management of their project development to satisfy project objectives and enable more efficient use of the increasingly limited available resources. Each discrete step in advancing the project from scoping study to operations needs to be integrated, reducing the amount of rework and duplication. This paper is primarily a consolidation of existing ideas on project management systems but also introduces new concepts to solve current issues. It describes the basic components of a typical mining project, the issues that commonly arise, the key attributes, and critical steps required for an effective integrated project management system covering projects from initial scoping studies through to project commissioning and operation. This paper focuses on technical study components of the mine development project with allowance for transitioning to design and construction and operation phases.

Jan 1, 2006

By A. C. Burr

This progress report covers the period from January 1949 to the end of the fiscal year, June 30, 1950. Three runs were successfully completed, and one run was terminated as the result of failure of a cast reaction tube. Including the abbreviated run, the gasifier was operated for 1,915 hours, during which some 428 tons of natural and steam- dried lignite was partly gasified In producing 20 million cubic feet of gas. Gas-production rates varied from 7.8 to 16.4 thousand cubic feet per hour, the latter being the highest production rate yet reached; hydrogen-carbon monoxide ratios of the product gas varied from 1.85, the lowest ratio yet produced, to 6.5; and heat-transfer rates through the heated wall of the outer tube varied from 2,100 to 4,400 B.t.u. per square foot an hour. The general objective of the project is to establish the technology and economy of the gasification of lignite in an externally heated, metal, annular retort. Specific objectives include determination of the useful life of the metal retort tube, which is a continuing problem, and special objectives that were established for each run as part of the systematic investigation of the basic variables of the gasification process. For runs 10 and 11 the special objective was the influence of the lignite feed rate on gasification; for run 12, a comparison of dried and natural lignite, and the production of gas having a hydrogen-carbon monoxide ratio less than 2; and for run 13, the influence of a gradually increasing steam rate with steam admitted to either the upper or lower reaction zones. In addition, during each run the sulfur distribution and concentration in the product gas and char were investigated. Experimental results obtained using the lignite feed rate as the variable indicated that the gas yield per ton of natural lignite varied inversely with the feed rate. Comparison of the gasification of natural and steam-dried Dakota Star lignite indicated that the dried lignite was a superior gasification material because: 1. The hourly gas production was higher at normal combustion space temperatures under nearly equal experimental conditions. 2. On the moisture- and ash-free basis, a considerably higher feed rate could be maintained at a relatively high percentage of carbon gasified. 3. At nearly equal moisture- and ash-free feed rates, the specific gas yield was higher. The location of steam admission was found to be important because the gas yield per ton of natural lignite was higher when at least a portion of' the process steam was admitted to the upper reaction zone. Heat balances showed the potential heat in the gas and char to be 71.8 to 83.6 percent of the total heat input. The sulfur concentration in the product gas was low, being in the range of 35 to 140 grains per 100 cu. ft., of which 1.5 to 2.3 grains was organic sulfur. Careful measurements and inspection of the 310-alloy rolled plate tube following runs 11, 12, and 13 showed no excessive corrosion; however, some radial deformation had occurred indicating that deformation or creep might be the limiting factor in the life of the tube.

Jan 1, 1953

By D-J Min

Strategies and achievements in the Asian steel industry to construct industrial ecological chain are reviewed largely in the case of Japan, Korea and China. Emphasis is placed on the development of resource circulatory system for the minimisation of various wastes and emissions of green house gases (GHG), toxic gases and polluting particulates. The minimisation includes:Rationalisation of iron and steelmaking processes; Implementation of available relevant measures/technologies; Life cycle assessment in designing steel from semis to assembled products; Reduction, reuse and recycling of materials and energies; and Utilisation of core competence technologies to process domestic and industrial wastes. In view of global nature of the above wastes- and emission-issues, inter-industrial linkage and international cooperation across the borders in the Asian countries have become more important. Inter-industrial linkage definitely serves to cut back the wastes and emissions. Examples of such linkage and factors influencing the sustainability of the linkage are described with expectation for further development of the linkage. Importance of international cooperation cannot be overstressed under the circumstances where steel production in China exceeded 220 Mt and world production exceeded 945 Mt in 2003 and is still increasing. Practical measures are discussed to enhance the linkage and cooperation for effectively promoting the reduction, reuse and recycling, including implications for the nonferrous industry.

Jan 1, 2004

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By Tiziana Apuani

The study refers to an area of about 70 km2, extended in the Italian Central Alps along the the San Giacomo Valley where different civil and mining works are present The regional geological setting is related to the Pennidic Nappe arrangement, characterized by the emplacement of sub-horizontal gneissic bodies resulting from the Mesoalpine isoclinalic folding of crystalline basements, emplaced throw East, and separated by matasedimentary cover units. The investigated geological rocks, belong to the ?Tambò?Unit, overlapped by its meta-sedimentary cover and by the ?Suretta? Unit. The tectonic contact gently dips to the E?NE. The valley, furrowed by the Liro Torrent, follows a N?S striking tectonic lineament, almost parallel to the nappe contact. A number of more then 70 sites, distributed in the studied area, were chosen and detailed structural and geomechanical field surveys were performed to characterize the rock masses, its intact rock and discontinuities. The procedure identifies the number of joint sets, their representative orientation, the set spacing, the type of movement, the amount of dilatation, the degree of alteration, the roughness coefficient, the presence and nature of infill. Rock mass quality indexes, such as the Rock Mass Rating (Bieniawski, 1989) or the Geological Strength Index (Hoek et al. 2002) have been evaluated in each surveyed site. The work is a contribute in assessing how the geometrical and geomechanical properties of the rock masses can be regarded as regionalized variables. The spatial distribution of these properties is a function of the geological and structural phenomena at which the rock masses have been subjected. The presented geostatistical analysis regards the spatial variation of the orientation of the most representative joint set.

May 1, 2009

By J. R. Thoenen, B. H. Clemmons, A. H. Reed

"INTRODUCTION AND SUMMARYOverall red-ore reserves in the Birmingham, Ala., area were estimated in 1910 by E. F. Burchard 4/. Since then mining has progressed into areas classed by Burchard as ""unavailable for exploitation"" under conditions existing at that time. This is understandable when it is considered that red iron ore was valued at $1.19 a gross ton at the mine in Birmingham in 19102/ and by 1948 had risen 300 percent; 6/ that skips had replaced cars in slope haulage; that mechanical loading and rubber-tired haulage had replaced hand loading and mule or locomotive haulage; and that other more efficient mining methods had been introduced. Intensive study during the intervening 40 years has been given to ways and means for upgrading the low-grade ores in the area and combining or blending them with raw red and brown ores for improved blast-furnace feed.It is reasonable to expect that future progress in mining efficiency and increased knowledge of the beneficiation characteristics of marginal ores will permit extraction of red-iron minerals now considered uneconomic.The Bureau of Mines has undertaken to restudy iron-ore reserves of the Birmingham area to determine what tonnage and grades of mineral are present; what is necessary to make them amenable to mining; what further advancement is possible in beneficia¬tion methods; and where increased production may be obtained in the area if and when required. This study has been underway for the past 2 years, but research into the beneficiation of marginal ores has been in progress at the Southern Experiment Station for the past 30 years. Many results of that research have been adopted in commercial practice in the area. Other results have not been published but are pre¬sented here in condensed form as an important factor in assessing marginal deposits with respect to their importance as ore reserves.An interim discussion of the salient features of past history and progress, as well as the data developed during the years of research in beneficiation at this station and the present field investigation, will make for a better understanding of the present position as well as be useful in evaluating future potentialities. Discussion in this paper is confined to the main Birmingham Basin area, which contains the largest concentration of hematite ores in the district."

Jul 1, 1953

By Andre Zingano

The variation in pillar behavior at underground coal mines working in the Bonito coal seam is observed in both research and mining company case studies. There is no consistency in pillar behavior, as it varies from mine to mine. In some cases, it is possible to find rib yields for both excavation modes and pillar sizes. This paper?s objective is to investigate pillar behavior for different load conditions and pillar sizes. Three-dimensional numerical simulation models considering these factors were built. A matrix was then assembled to compare pillar behavior between loading conditions, as well as between different pillar sizes with the same loading condition. The results showed some pillar rib plasticity due to vertical loading and stress relief independent of the pillar size and load. For the same load conditions, the yielding thickness is the same for different pillar sizes.

Jan 1, 2012

The 112th Annual National Western Mining Conference (NWMC) hosted by the Colorado Mining Association (CMA) drew some political heavyweights, if by voice only, into the fray of two of the hottest topics that the mining industry is currently facing ? climate change and the new energy economy. A changing political landscape in Colorado, as well as in Washington D.C., has given rise to questions about the economic future of the United States and the mining industry?s role in that future. While there has been a recent push away from traditional energy sources to a ?new energy economy? that is rich in renewable energy sources such as wind and solar, the NWMC?s agenda emphasized the role that minerals will play in new energy technologies. The conference was also full of talks about the industry?s role in reducing the United States? reliance on foreign oil and other mineral commodities. To that end, an impressive lineup of speakers were invited to attend the three-day conference Feb. 8-11, in Denver, CO. Unfortunately, Mother Nature had other plans and three of the four headliners, including Denver?s mayor and Democratic candidate for governor of Colorado, John Hickenlooper, were unable to get to the conference because of a massive blizzard on the East Coast locked them in Washington, D.C. However, with modern technology, a full auditorium heard presentations from Hickenlooper, National Mining Association (NMA) president and chief executive officer Hal Quinn and Glenn Kelly, vice president, government affairs for NMA. Republican candidate for governor of Colorado, Scott McInnis, did speak to the crowd in person.

Jan 4, 2010

By Junhwan Lee

Pipe piles can be either closed- or open-ended piles. Pile load capacity for a closed-ended pile consists of the shaft and base resistances, while, for an open-ended pile, it consists of shaft, soil plug, and annulus resistances. In order to investigate the pile load capacity of both closed- and open-ended piles, two field pile load tests were performed. For the open-ended pile, the fully instrumented double-walled system was used to separately measure all the components of the pile load capacity. The soils at the test site were predominantly granular soils with relative densities varying from loose to dense with increasing depth. The incremental filling ratio (IFR), which affects significantly the load capacity of open-ended piles, was also measured during pile driving. The test results indicated that the total load capacity of the closed-ended pile was higher that that of the open-ended pile, mostly due to the difference in shaft capacity. The shaft and base load capacities of the open-ended pile were 44% and 20% lower than the corresponding values for the closed-ended pile.

Jan 1, 2003

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By G. T. Lineberry, W. J. Wiehagen

A Paradigm Shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results invokes questions such as: How much was produced? At what cost? And, was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as preeminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured, and formed new coalitions. Investments in new technology and concentration on productivity have been part and parcel with these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. These changes in mining present an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now might offer some interesting opportunities for the future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work force. The WCPM work Crew Performance Model, see pp. ) is one approach to defining, capturing, and transferring this expertise.

By Yuchen Wu, Jing Mei, GUOZHONG LIU, KE GAO, Songjie Tian, Jianwei Cheng, Yu Wang, Yuhang Wu, Hui Wang

The stability and integrity of protective coal pillars between the longwall working face and development roadways are greatly affected by the mining activities such as the development face advancing or retreat mining. Due to underground strata pressure, the coal pillar cracks could be further developed and then the air leakage passages (mainly cracks) could be produced greatly. The air circulation caused by the atmospheric pressure difference between the two sides of the coal pillar may also provide suitable conditions for the possible spontaneous combustion of the residual coal in the mine gob. In this paper, a typical the protective coal pillar in a Chinese coal mine is studied. The deformation and stress of coal pillars during the mining process of longwall working face are simulated by using FLAC3D. The displacement and strain of coal pillars are analyzed. Two indexes, the linear fracture rate (LFR) and area fracture rate (AFR), are introduced to characterize the development of internal cracks’ development within coal pillars. By using field measurement, the air leakage intensity distribution due to coal pillar cracks is obtained; the equation of air leakage resistance of coal pillar under the influence of mining is derived. Then, the possible location of large air leakage of coal pillar is determined, which can be used as guidelines to study the possibilities of coal spontaneous combustions happening in pillar or mine gob. The research results help to control such potential hazards in advance.

Jun 16, 2022

By W. P. Nel

The introduction of the Higher Education Qualifications Framework (HEQF) and the updated Higher Education Qualifications Sub-Framework (HEQSF) has caused many South African university departments to rethink their programme qualification mixes (PQMs). In addition to the requirements stated in the HEQSF, a number of other factors have to be taken into consideration by a university department. These factors include, for example, the standards generated by the Engineering Standards Generating Body (ESGB) and subsequently approved by the Engineering Council of SA (ECSA) and the need to prepare students for various categories of professional registration with ECSA. This means that a university department has to choose the correct mix of Learning Programmes (LPs) from the HEQSF menu (which consists of 13 types of LPs). Preparing students for ECSA registration is aligned with the mission of universities, which is to teach and undertake research. However, research and the LPs associated with research go beyond the requirements for current ECSA registration. Assuming that universities offering engineering LPs would elect to prepare students for both ECSA registration and teach them to produce research outputs, which is mostly done at Master and Doctorate levels (NQF Levels 9 and 10), then it follows that academics are more interested in NQF Level 5 to 10 pathways (abbreviated as ?L5-10?) rather than the shorter pathways required towards professional registration. (For example, ECSA requires an NQF L5-L7 pathway for registration as a candidate professional technologist. This specific pathway may consist, for example, of two LPs, namely the 360-credit Diploma and the Advanced Diploma.) A L5-L10 pathway is a combination of LPs that will prepare the learner with a NSC (or equivalent qualification at level 4) to Doctoral level (level 10). Universities may choose at least four major pathways from the HEQSF menu in order to educate and develop students from NQF Level 5 to 10. However, various pathways towards registration in the category of candidate with ECSA are also embedded into these four NQF L5-L10 pathways, where each consist of a unique combination of LPs. Each of these pathways has an opportunity cost, and economic reality means that smaller departments may have to choose between the four pathways. Of all the many factors involved in PQM decision-making, the focus of this paper is on the HEQSF requirements, ECSA standards, and ECSA registration and how these, together with the various qualifications and educational LPs provided for by the HEQSF may impact on the PQM decision taken by engineering departments and schools at South African universities. The proposed four NQF L5-L10 ?pathway tool? for PQM decision-making may be useful for pointing out the advantages, disadvantages, and applications of the various pathways and combinations of pathways. Rather than deciding from a menu of thirteen qualifications and associated LPs, this article proposes that decision-making be undertaken on the basis of a menu of four main articulated ?NQF L5-L10? pathways (which also include one or more of the ECSA?s pathways for professional registration). The proposed ?NQF L5-L10 pathway? tool is an attempt to move one step closer to the aim of achieving a structured decision-making approach for designing a PQM at departmental level.

Jan 1, 2014

The Department of Mineral Resources has a statutory responsibility for mine site environmental management and control in New South Wales. The Department is focusing on an environmental management systems (EMS) approach, as a management tool to achieve æbest practiceÆ outcomes both within our own organisation and on mine sites. One of the DepartmentÆs tools is environmental risk assessment and management which incorporates the Mining, Rehabilitation and Environmental Management Process (MREMP). The MREMP was introduced many years ago in order to integrate the activities of key stakeholders who may have a material interest in the mine. The MREMP provides an ideal mechanism by which ædue diligenceÆ requirements and environmental management programs can be integrated into mining operations and lead to a sustainable post-mining land use.

Jan 1, 2002

By E. G. King

Many of the existing thermodynamic values for the titanium halides are estimates, including all the entropies and high-temperature heat contents of their crystalline and liquid phases. This report contains the results of low-temperature heat capacity measurents (which lead to entropy values at 298.15° K,) and high-temperature heat-content measurements of four halides - trichloride, tribromide, tetrabromide, and tetraiodide. The new data are combined with selected heat-of-formation values at 298.15° K. to obtain improved values of the heats and free energies of formation of these halides at high temperatures, thus supplementing the previous data of Kelley and Mah.5/ ACKNOWLEDGEMENTS This investigation was conducted under a cooperative arrangement between the Federal Bureau of Mines and the Department of the Navy, Office of Naval Research. The work was done by Bureau of Mines personnel using Bureau of Mines calorimetric equipment. The Office-of Naval Research supplied the supporting funds and arranged for procuring the samples of the titanium halides. The samples were prepared and analyzed by the Inorganic Chemistry Section, Division of Chemistry, National Bureau of Standards.

Jan 1, 1961

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system's response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By L O. Filippov, C H. Veloso de Melo, A Correa De Araujo

Froth flotation of iron ores is one of the most widely used methods to upgrade iron ore into high-grade concentrates. In recent years, reverse cationic flotation of iron ores has been specifically the subject of several studies. Since quartz is the most common gangue mineral in iron ores, understanding the behaviour of this mineral was the main target of the majority of such studies. However, with the depletion of mineral deposits considered rich and easy to process, it has become more common to find iron ores with complex gangue minerals, which are composed not only of quartz but by a variety of silicates. The mineralogical composition of the ore is an important factor for determining reagents and mineral processing parameters. The mineralogical suite of an ore also presents a paramount role for operational optimisation of any given flotation process. Some studies were performed with different types of amphiboles and other Fe-bearing silicates, for example, but the influence of the mineralogical nature of these silicates in reverse cationic flotation has not been fully explored and will be discussed here. Changes in the traditionally used reagent scheme for reverse cationic flotation, generally including alkaline pH values, polysaccharides as depressant (mainly starches) and primary ether amines and diamines, are expected when dealing with iron ores with complex silicate gangue composition.CITATION:Veloso de Melo, C H, Correa de Araujo, A and Filippov, L O, 2017. Reverse cationic flotation of iron ores with complex silicate gangue minerals, in Proceedings Iron Ore 2017, pp 241–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017