Search Documents

By G. F. Jenkins, P. S. Hobden

Toronto as a geographical area provides an exceptionally wide variety of subsoil stratiphication. Tunneling consequently required a very wide range of adaptabilities to meet its changing conditions. This discussion will provide a summary of work performed in both earth and rock formation using three of our recent works to describe a Contractor's experience. The general subsoil stratigraphy is known to consist of deposits laid down during the Illionian Glaciation followed by the Samgamon Interglacial Stage and finally the Wisconsin Glaciation. All these deposits are underlain by shale bedrock of the Dundas formation. As a whole the Dundas formation is predominantly a greyish blue, thinly bedded shale. The engineering characteristics of the shale vary considerably, however, between a blue clay (argillaceous) shale and a much lighter (in colour) silty and sometimes sandy (arenaceous) shale, and occasional limestone layers. The Illionian deposits are usually found to be layers of pebbly clay till and an overlaying layer of contorted varved-clay. These glacial deposits can be overlain by a thick layer of sandy silt to silty sand which is identified as the Samgamon Interglacial sediments. Because of the action of erosion the Wisconsin till sheets, many times separated by interstadial sands, can vary greatly in their number of layers from zero to three or more.

Jan 1, 1997

By C M. Ramotsabi, F Bornman, W Erasmus

Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and heavy mineral ores (Wills, 1992). Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating many minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid such as water or air (Wills, 2006).The main operating variables for a spiral concentrator are the feed rate, the slurry concentration, the wash water addition and the position of the splitters used to separate the tailings, middlings and concentrate streams (Sadeghi, Bazin and Renaud, 2014). Wash water is an important control variable used to wash away entrapped light minerals from the concentrate stream (Burt, 1984; Bouchard, 2001). Sadeghi et al concluded the spiral operation to be sensitive to the wash water flow addition and resultant economic trade-off. Increasing the wash water flow rate increases the concentrate grade at the expense of the iron recovery.The paper addresses the effects of dripping wash water onto the concentrate stream of a spiral processing fine iron ore. The dripping wash water system offers a low flow alternative and could possibly provide a good balance between grade and recovery of valuable minerals without using excessive water. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentrations; the wash water rate and the splitter positions were kept constant.The use of wash water at 30 per cent, 35 per cent and 40 per cent solid concentration improved the Fe grade in the concentrate by about 1.5 per cent, six per cent and eight per cent respectively. The additional SiO2 rejected by the wash water is approximately three per cent, nine per cent, and 11 per cent at 30 per cent, 35 per cent and 40 per cent solid concentration respectively. Addition of wash water is shown to have minimum effect on grade at 30 per cent solid concentration, and Fe upgrades obtained with and without wash water were found to be similar. Notable upgrades were observed at 35 and 40 per cent solid concentration with wash water. The results obtained suggest that the additional SiO2 rejection by wash water increases with an increase in solid concentration. This suggests that the benefit of using the drip system is notable at higher solid concentration. It is believed that at lower solid concentration SiO2 particles are reasonably free to move around and are possibly less entrapped than at high solid concentration.The Fe grade/recovery and solid concentration relationship with wash water showed a non-linear correlation. The Fe grade increases with an increase in solid concentration up to a somewhat optimum point and then drops as solid concentration increases further. The recovery of Fe on the other hand follows a converse relationship with solid concentration, the recovery decreases from 30 per cent to 35 per cent solid concentration and then increases again at 40 per cent solid concentration. The increase in recovery at higher solid concentration could possibly be explained by the fact that the mass yield to concentrate also increases with solid concentration. Since recovery is a function of both grade and mass yield, the higher recovery at 40 per cent solid concentration is likely due to the high mass yield obtainable at 40 per cent solid concentration.The drip system could therefore possibly offer a safe guarding against grade and solid concentration variations without using excessive water, and possibly ensure that a product within specification is maintained.CITATION:Ramotsabi, C M, Erasmus, W and Bornman, F, 2015. Optimisation of wash water on an iron ore spiral to improve grade, in Proceedings Iron Ore 2015, pp 175–184 (The Australasian Institute of Mining and Metallurgy: Me

Jul 13, 2015

By G. S. Scott. R. L. Grant

Ammonium nitrate (NH4NO3), a white crystalline chemical compound composed of 35 percent nitrogen, 60 percent oxygen, and 5 percent hydrogen, has again attracted attention, due largely to the recent catastrophe on April 16 and 17, 1947, at Texas City, Tex. The fire and subsequent explosion on the steamship Ocean Liberty, outside the harbor of Brest, France, on July 28, 1947, has fur- ther increased the interest in the properties of ammonium nitrate. As a result of the Texas City disaster, several laboratories have undertaken research to determine more certainly what causes ammonium nitrate to detonate and under what circumstances. This is not the first time that ammonium nitrate has been involved in a disaster, and its properties reviewed from the standpoint of safety. The disaster at Oppau, Germany, in 1921, which involved an equimolec- ular mixture of ammonium nitrate and ammonium sulfate, prompted an intensive study in Europe and in America. In the United States the properties of am- monium nitrate are now of especial concern because very large quantites are being manufactured and shipped in interstate commerce and abroad. Many an- monium nitrate factories, which were built during the war, will manufacture increasing amounts of this compound for use as a fertilizer. It is the purpose of this report to present a brief summary and biblio- graphy of the published experimental facts about the properties and behavior of ammonium nitrate. The reader is referred to original publications for greater details of the investigative work, and for theoretical discussions. This report also includes a survey of ammonium nitrate fertilizer of the type involved in the Texas City explosions. In the past, authorities have not always agreed on the degree of hazard involved in the manufacture and handling of ammonium nitrate, as the following quotations from the literature indicate: Munroe (82) quoted the following from Turner's Chemistry (a book pub- lished in 1835): "When this salt is exposed to fire, it liquefies, emits aqueous vapor, dries and detonates." Berthelot (14) in his book, Explosives and Their Power, 1983, wrote: "Ammonium nitrate from the point of view of its volatility, and cn account of many considerations, may be regarded as a typical explosive substance."

Jun 1, 1948

By Xiangjun Zuo

This paper firstly reviewed the state of the art in the recycling of used Printed Wiring Boards (PWB), and then presented part of the authors study on the combustion of PWB powders with and without the addition of catalyst. During the combustion of PWB powders without catalyst addition, there were two obvious exothermic reactions, one at 300-380oC, the other at 450-500oC. With the addition of catalyst during PWB combustion, there were no obvious exothermic reactions, indicating that dehalogenation reactions are not exothermic: The results showed that NaHCO3 and CaCO3 were very efficient to control the emission of Br2 and C6H6, lowering 80% compared to the case without catalyst, Na2CO3 can slightly control the emission of Br2 gas but not for C6H6 gas mission, and NaOH has no any effect of the control of both gases.

Jan 1, 2009

By Y. Shiraishi, Y. Sakurai

A new method, the gliding cylinder method, was proposed as a wide range viscometer for the measurements of molten salts, slags, and glasses. The method consists of two coaxial cylinders, cylindrical bob and a vessel containing a liquid sample. There is a narrow gap between bob and vessel. When the vessel moves against the bob, the generated force on the bob consists of three types of resistance: (1) Stokes’s resistance on the bob, (2) a capillary flow resistance though an annular gap between vessel and bob, and (3) lubricating resistance in a gap. The last two can be calculated on a theoretical basis but the first cannot be estimated by a simple calculation since a wall effect did not calculate easily. However, it can be assumed that the generated force depends on both the viscosity of a liquid and velocity of the vessel. Thus, the relation between viscosity and a force at desired velocity of the vessel was measured using several standard reference materials including glycerol aqueous solutions and standard reference oils. The results depended on the magnitude of the gap between the bob and the vessel. For the wider gap, it was shown that the viscosity is a linear function of a gradient of force with respect to a vessel velocity. In contrast, if the gap is small, the viscosity depends on the gradient (of force with respect to velocity). This implies that the non-linear phenomena would occur in Stokes resistance. Though detailed analysis is in a further investigation, a calibration method can be applied to determine the viscosity by this method, because good correlation was obtained among these quantities. Viscosity of molten salts, such as NaNO3and ZnCl2was measured by this method as high temperature demonstration. Keywords: viscometer, viscosity, sphere pull-up method, fused salts, molten slags, glass melts

Jan 1, 2004

By L. A. Conley

This report, covering the period January through December 1976, contains abstracts of articles related to cost engineering and economics for chemical and petroleum plants, mining, and other mineral industries from the following periodicals: 1. Air Pollution Control Association Journal 2. Chemical Engineering 3. Chemical Engineering Journal 4. Chemtech 5. Coal Age 6. Coal Mining and Processing 7. Combustion 8. Drilling-DCW 9. Electrical World 10. Engineering and Mining Journal

Jan 1, 1977

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By Klaus Rieker

The main train station of Leipzig in Germany is currently being upgraded from a head station to a partially thru station. In order to achieve this, significant ground improvements are necessary. Soil freezing for example is used to create the excavation box retaining walls. The freezing works will be carried out from two tunnels with an inner diameter of 2.4 m (~ 8ft). The tunnels were constructed by the pipe jacking method. The cutter head of the machine was equipped with discs and scrapers. Driving and excavation was carried out using a bentonite supported face. Due to the small arrival shafts, the machine had to be lifted out in components. The essential limitation of settlements during the drives was achieved even better than expected.

Jan 1, 2008

By Almon F. Robertson

"INTRODUCTION At various times, North Carolina has supplied small quantities of brown-iron ore to the furnace o the South. Between 1917 and 1920, the quantity reported to the Federal Geological Survey was 126,000 tons. Most of this came from Cherokee County. 3/In furtherance of the program initiated by the Bureau of Mines to develop additional reserve of iron ore during the emergency, the Cherokee County deposits were examined by an engineer 4/ of the Bureau of Mines, and work was recommended on,12 properties.The project was begun in April 1944 and continued intermittently until April 1945, when work was stopped. During this period, eight properties were explored, and an additional property was mapped.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch; Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By Joseph E. Schiller

As part of the Bureau of Mines research on identification of asbestos fibers, a method was discovered for removing asbestos fibers from water. This report describes this process and its theory of operation. The surface charge of amphibole minerals in potable water was found to be negative, and in common with most other silicate minerals, the isoelectric point of amphibole asbestos fibers lies in the pH range 4 to 6. Magnesia is one of the rare oxides with a high isoelectric point of about 11. The surface of magnesium oxide will, therefore, be positively charged in water at pH 6 to 6, while the electric charge an. amphibole asbestos fibers is negative. Because of the electrical attraction of these oppositely charged solids, it was possible to remove negatively charged asbestos fibers from water by percolating water that contained suspended-asbestos through a porous bed of magnesium oxide particles. A bed of 100/200-mesh MgO was added to a glass tube with a cotton plug. Aqusous suspensions of 1 to 10 ppm cummingtonite asbestos (amosite), crocidolite, and chrysotile were percolated through this porous plug of MgO. Even though chrysotile is positively charged below pH 11, MgO is an effective filter medium for removing it. The highly basic MgO appears to cause the chrysotile to flocculate and attach to particles within the bed. Scanning electron photomicrographs indicated that essentially complete removal of the fibers from water was accomplished. Other materials tested as contact filter media and found to be ineffective or only partially effective were sand, calcite, carbon, diatomaceous earth, and cellulose. Acidic alumina collected amphibole fibers but not chrysotile fibers.

Jan 1, 1980

By Jian Wu

In this paper, the surrounding rocks and the supports in a longwall are taken as an integral, i.e. a system. The structural characteristics and behavior of the system are discussed based on in-situ observations. A set of equations, which describe the interaction among the support, immediate roof and main roof, are developed. These equations can be used to design the longwall powered supports more reasonably and economically.

Jan 1, 1989

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The REFLUX Classifier is used to perform particle separations on the basis of density utilising a set of parallel inclined channels positioned above a vertical fluidised section. In continuous mode, feed enters part way up the vertical section, while fluidisation water is introduced from below. Lower density particles are conveyed upwards and collected in an overflow stream, while high density particles segregate onto the inclined surfaces, settle to the base of the system and empty via an underflow stream. Pressure transducers are used to measure the suspension density in the vertical section. This suspension density is maintained by a pneumatically controlled underflow valve to maintain a target suspension density or ‘set point’.Previously, Galvin et al (2010) demonstrated the significant improvement achieved via a new laminar-shear separation mechanism, achieved by utilising closely spaced inclined channels in the REFLUX Classifier. For the separation of low-density coal particles from mineral matter, a channel spacing of 6 mm proved effective; however, for the separation of gangue minerals from much higher density minerals such as iron ore, the shear-induced lift needs to be even higher. In this paper, we examine the influence of two different channel widths on the continuous processing of an industrial iron ore feed in the REFLUX Classifier. It was found that when moving from 6.0 mm to 3.0 mm channels, the ability of the system to reject coarser gangue material and retain finer high density material across a particle size range from 0.125 to 1.0 mm was increased, resulting in a higher grade product.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2017. Influence of shear rate on separation of iron ore fines using the REFLUXTM Classifier, in Proceedings Iron Ore 2017, pp 205–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Shenghui Chu, Zhibiao Guo, Dongshan Yang, Yuanxin Zhao, Xiaohui Kuai, Jingwei Gao

The technology of automatically formed roadway without pillars (AFRP) via roof cutting and pressure releasing (RCPR) is a reformatory method for gob-side entry retaining, which automatically creates a roadway by utilizing the fragmenting and expanding properties of rock strata and the mining pressure, to realize a novel technique for coal mining without coal pillars. The Anju Coal Mine is the first kilometer-deep mine where this technology is applied. To conduct a geomechanical model experiment, this research uses the 5307 working face in this mine as its backdrop. The experimental results show that this technology can efficiently decrease the pressure of the AFRP surrounding rock. The roof maximum stress of the AFRP is 21% lower than that of the belt roadway, while the side abutment pressure of the former is 13.4% lower than that of the latter. The comparison of model experiment data and field monitoring data shows that the roof and floor approaching deformations on the roof-cutting side and solid coal side of AFRP differ by 8.8% and 9.6%, respectively. The model experiment results and field monitoring data show good agreement, and the deformation of the AFRP surrounding rock can be successfully managed by this technique. The study’s findings can serve as a guide for using this technology in kilometer-deep coal mines.

Jul 31, 2023

By R L. Brathwaite

Previous paleodepth studies of low-sulphidation epithermal Au-Ag deposits in the Coromandel region indicated that economic gold mineralisation was generally limited to a depth zone of 100 to 400 m below the paleosurface. Notable exceptions are Waihi and Karangahake, where ore shoots extended to depths of about 750 and 900 m respectively. These studies have been extended to include Au-Ag, Hg and Sb epithermal deposits in Northland and the Taupo Volcanic Zone. The main paleodepth indicators used are sinters and hydrothermal eruption breccias, hydrostatic pressures estimated from homogenisation temperature measurements on fluid inclusions, and hydrothermal alteration mineralogy. Also the occurrence of lacustrine and fluvial sediments is an indicator of the paleosurface at their time of deposition. Selected paleodepth indicators have been compiled and mapped in a GIS environment. The distribution of the paleodepth indicators are used to define regional variations in erosion levels, and may be useful in predicting areas most likely to preserve the optimum depth window for gold deposition. In the Coromandel region, regional stream sediment geochemical data has also been used to broadly define erosion levels in terms of Zn, Pb and Cu representing deeper base metal zone mineralization and Hg and Sb representing shallower cinnabar and stibnite mineralisation. The interpretations of paleodepth and potential reconstruction of paleosurfaces are limited by the paucity of data, poor age control on the paleodepth indicators and the epithermal deposits, and marked relief and complex stratigraphy in the volcanic terranes.

Jan 1, 2003

By Werner Burger

The last decade has witnessed a rapid development and application of slurry and EPB type tunnel boring machines. Both soft ground types are able to excavate tunnels in unstable ground conditions below the water table with positive face support. The most significant component of the excavation process is the cutterhead and tool con-figuration were the excavation and face support meets the geological challenge. The TBM downstream processes cannot take place unless the cutterhead and tools effectively do their job. This paper will review the current state of the art design for both slurry and EPB cutterheads and highlight both common as well as geological specific design features.

Jan 1, 2007

By Walter J. Frank

The purpose of the work covered by this contract is to develop a means of designing splice connectors which will significantly improve mine trailing cable splice performance. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. Because of the empirical nature of this effort, time has been devoted to explaining the derivations of the test procedures used. Special attention is given to the splice flexing machine which served as the backbone of the test program. In order to familiarize persons with connector terminology, a section is devoted to a glossary of pertinent terms. Various types of cable joints are also defined. The major effort is a connector design parameter study. Utilizing the optimum parameters developed along with the suggested design procedure outlined in Appendix I should result in significantly improved splice performance and thus meet the objectives of this contract. A field test program was instituted for the purpose of insuring adaptability of connector design and associated installation tooling along with a field performance study. During the course of work, other significant factors affecting splice performance were uncovered. Although not covered by the scope of this contract, a brief discussion is presented for the purpose of stimulating interest in what is considered other fruitful areas for improved splice performance.

Jan 1, 1976

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By Wijnand Dalmijn, Hans de Ruiter

Experience over the past eight years has proven that partnership and cooperation in mineral engineering education is essential to maintain programs in this field. At this moment the joint European Mineral Masters Engineering Course (EMMEC) has three programs in the areas of mining, minerals engineering and geotechnical/environmental engineering, offered by combinations of nine universities in seven European countries. About 25 companies are associated with the universities in the Federation of European Mineral Programs (FEMP) which coordinates these activities. The EMMEC has applied for recognition under the newly launched EU “Erasmus Mundus” program in which the EU makes 280 million Euro available for bursaries for non-European students and scholars.

Jan 1, 2005

By G. B. Shea, R. A. Cattell

This resume of the work of the Petroleum and Natural - Gas Division of the Bureau of Mines for the fiscal years 1940 and 1941 is the second of a series. of progress reports . It brings forward from the 1939 annual report information on the course of activities of the division in carrying out its objectives of increased conservation and better utilization of petroleum, natural gas, and related resources through a coordinated program of research and fact - finding . It discusses, also, special assignments. executed for other Government agencies, which in recent years have constituted a considerable part of the division's work ." . In the present national emergency, in which petroleum is so essential , many of the Bureau's research activities bear directly on the availability, conservation, and use of petroleum for national defense . Accordingly, during the past year attention has been focused for the most part.on.problems associated with the needs of national defense . Several long-time researches , which in themselves are potential sources of desirable knowledge , were judged to be of secondary importance under present conditions and accordingly were suspended . Studies also were oriented in line with rapidly changing conditions to meet the demand for accurate findings on short notice . The Petroleum and Natural - Gas Division has experiment stations at Bartlesville , Okla . , and Laramie, Wyo . , a field office at Dallas , Tex . , and a field office and laboratory at San Francisco , Calif . It also operates the Government helium plant near Amarillo , Tex. In addition to the helium operations , some of the petroleum and natural - gas research activities are conducted at the Amarillo plant .

Feb 1, 1942

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010