Search Documents

By C. H. Fisher

[Many methods of analyzing tar oils for their tar acid and base content have bun employed in connection with both academic and. industrial investigations. Most of these analytical procedures are based on the diminution in volume caused by extraction with alkali and mineral acids (contraction method), although other methods haves been employed.4/ In many instances the adoption of an analytical method was not preceded by adequate study, and, as a consequence, the literature, on this subject is conspicuous for its contradictory claims and recommendations. It has bin shown in the, case of certain synthetic solutions5/ that large errors may result if the analysis is carried out by simple extraction with alkali and mineral acids.]

Jan 1, 1936

By P. James

"INTRODUCTION Control of target stream acidity is widely used in MIW (mining influenced water). Tailoring pH (a measure of acidity) finds application for controlling key chemistry in both process and waste streams. Traditional lime addition for neutralization and precipitation is most often used but has high reagent costs and results in large amounts of mixed metal sludge requiring costly disposal. A new adaptation of BPS’s patented DEMET™ technology (Dynamic Electrolytic Metal Effluent Treatment) platform offers a potentially improved and “reagentless” alternative to traditional chemical addition for pH adjustment. Electricity rather than chemical addition utilized in BPS’s proprietary approach controllably tailors target stream pH. The method offers a simple, low-cost processing technique yielding cleaner treatment chemistry. BPS’s “green” approach may yield lower operating (OPEX) and life cycle costs and significant reductions (up to 50%) in sludge generation compared to conventional lime treatment. It can also allow new opportunities to generate revenue via selective recovery of valuable processing byproducts. Specific savings and revenues depend on the target site chemistries, details, and processing goals. A more detailed discussion of the process and its operational principles may be found in Reference One.[1] Here application of the BPS treatment to POx (Pressure Oxidation) leaching as an alternative to traditional chemical addition is examined. An example operation process flow for gold mining is considered.[2] Promising processing points for potentially replacing conventional processes with DEMET are noted. The possibilities for lowering OPEX costs, lessening sludge creation, and capturing various valuable byproducts and residuals are examined. Financial life cycle benefit estimates of the principal gains provided by DEMET application to the example operation are noted. Extension and generalization of the analyses to a wider range of scenarios is explored."

Jan 1, 2016

By J. Chlopas, D. J. Barratt, M. V. Sharp

"This paper describes the modifications made to the Fox Mine copper concentrate bin in order to obtain a continuous flow condition. The design of these modifications is based on test results obtained on Fox Mine concentrate using the flow factor testing machine in the research facilities of Cominco at Trail, B.C.The original design consisted of a cylindrical steel bin on a concrete slab with two slot-discharge openings. Based on predictions of the maximum mass flow hopper angle for conical and wedge shaped hoppers for the concentrate on various potential bin lining materials, Ultra-High Molecular Weight (UHMW) Polymer was selected as a liner.Using the recommended angles for conical and wedge shaped hoppers, the profile of the bin base was changed to suit the existing slot openings.The initial method of fastening the liner resulted in failure of the connections. Subsequent modification to the zinc concentrate bin fastener system proved satisfactory and it has now been in operation for over one year without any separation of the lining material.Utilization of flow testing procedures on concentrate samples has demonstrated that proper design of storage bins or hoppers to achieve continuous flow can be incorporated into the design of new plants."

Jan 1, 1978

By L Barro

There is currently a worldwide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow characteristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A capillary rheometer, designed to handle settling suspension, has been used for determining rheological properties. Brown coal of 0.0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦C - 319¦C. Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physicochemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage. Apparent viscosity increased sharply with increase in solids concentration and suspensions at higher concentration behaved as non Newtonian liquids. Viscosity decreased with increase in temperature; rate of decrease slowed down with increase in temperature.

Jan 1, 1980

By Frank E. Chase

Kettlebottoms are columnar masses of rock--the preserved casts of ancient tree stumps--embedded in coal mine roof strata (of which they are a part). Because unsupported kettlebottoms can detach from a mine roof without warning, they are a hazard to miners. The primary objectives of this investigation were (1) to better define and describe kettlebottoms and (2) to evaluate kettlebottom support techniques in terms of safety and effectiveness. A telephone survey of mine operators, interviews with Mine Safety and Health Administration (MSHA) personnel, and underground mine visits were conducted in Pennsylvania, West Virginia, and Kentucky. Information gathered during this investigation indicates that the size and frequency of kettlebottoms in mine roof are dependent upon past geologic events and biological processes active during the deposition of roof sediments. To ensure the safety of mine personnel, all undermined kettlebottoms should be supported. The roof should be bolted next to kettlebottoms less than 3 ft in diameter, close enough to allow a portion of a wood or steel header to be extended beneath each kettlebottom for support. Two bolts and a wood plank or steel strap should be employed to support kettlebottoms over 3 ft in diameter.

Jan 1, 1983

By B. J. du Plessis

Automation of the conventional grinding circuits of Palabora Mining Company (PMC) required that adequate instrumentation and a control system had to be put in place, after which extensive testing had to be done to evaluate different grinding control strategies. The objective was either to optimize the particle size from the grinding circuit, or to increase milling circuit throughput while maintaining particle size at existing levels. Prior to automation of the process as described below the circuits were controlled manually. No on-line information on cyclone feed densities, cyclone feed flow or cyclone overflow particle size was available. This type of control relied heavily on interpretation of the process parameters by the operator and on his ability to make informed decisions on what the set points should be. An integral component of the automation process was the installation of a SCADA package (SysCad SDX) for implementing the on-line control strategy. A self-correcting model for prediction of cyclone particle size was developed and implemented on the SDX. The model is calibrated using values from the particle size analysers while they are operational. If the particle size analysers choke or fail for any reason, the model continues to provide a good estimate of the particle size. This technique ensures that a continuous particle size indication is available compared to the intermittent reading from the instrument. The continuous signal allows particle size to be used as a process variable for control purposes. A strategy was developed and implemented which allows for the production of a controlled grind size from the conventional milling circuit to the flotation circuit. The grinding control strategy allows for the control of particle size from the individual cyclone overflows. This strategy allows the operator of the process to increase or decrease production rate by specifying a coarser or finer grind size required for flotation.

Jan 1, 2001

By J L. Mauk

The Sovereign, Jubilee, Scotia and Jasper Creek prospects occur in an area of ~3.0 km by 2.5 km (~7.5 km2) in the Hauraki goldfield. The prospects are hosted by andesitic to dacitic flows, autoclastic breccias and localised pyroclastic and air fall deposits. Jubilee and Sovereign prospects lie along the northern and southern parts of the Waitekauri Fault, respectively, whereas Scotia is located ~1 km to the E, and Jasper Creek a further ~1.2 km to the ENE. Wall rocks are typically intensely altered, although the degree of alteration becomes more variable east of Scotia and at Jasper Creek. Alteration minerals include quartz, adularia, albite, chlorite, pyrite, illite, interstratified illite-smectite, smectite and calcite. Several of these minerals have distributions that show distinct zonation with adularia most abundant at Sovereign and Jasper Creek, but restricted to shallow levels at Scotia. Illite occurs throughout Sovereign and Jubilee plus the western margin of Scotia where it grades into interstratified illite-smectite; smectite predominates at Jasper Creek. Veins are uncommon and typically narrow, but show distinct zonations. Quartz veins are more abundant at Sovereign and Jubilee, whereas calcite veins are more abundant at Scotia and Jasper Creek. Laumontite veins occur at Scotia, and rare clinoptilolite, mordenite and stilbite veinlets with calcite occur at Jasper Creek. Fluid inclusion in quartz and calcite homogenised between 141¦ to 272¦C and trapped a dilute solution with an apparent salinity of less than 2.6 weight percent NaCl equivalent. Homogenisation temperatures are hottest at Sovereign (average 241¦C) and Jubilee (average 239¦C), cooler at Scotia (average 204¦C) and coolest at Jasper Creek (average 162¦C). Calculated paleowater table elevations suggest the water table was 680 m to 750 m above sea level at Sovereign and Jubilee, 450 m at Scotia and 225 m at Jasper Creek. The current data suggest three scenarios that can explain why Sovereign and Jubilee are deep and hot, whereas Jasper Creek is cool, shallow and marginal; 1.   some or all of the prospects may represent separate overlapping hydrothermal system, 2.   a high-relief hydrothermal system on the side of volcano with an inclined water table and outflow towards Jasper Creek, and 3.   a low-relief hydrothermal system that has been either tilted or block faulted with greatest uplift and erosion to the west.

Jan 1, 2005

By J. H. Wernick

IN temperature-gradient zone-melting1 a molten zone is moved through a solid or across a solid surface by the establishment of a temperature gradient. This technique has both practical and fundamental aspects. One practical application is to make p-n junctions for semiconductive devices, particularly for devices in which the junctions are desired within the semiconductor. From a fundamental point of view, the technique is being investigated as a method for determining diffusivities in liquid alloys, and preliminary diffusivity results have been reported by the writer." In this paper, the effects of crystal orientation, temperature, and molten zone thickness in temperature-gradient zone-melting, and the bearing of these effects on diffusivity measurements and n-p-n junction formation are discussed. Experimental Procedure An effect of crystal orientation was noted in early experiments. To facilitate its study, movements of wire zones across a surface, rather than through the body of a single crystal, were observed for various surface planes and travel directions. The experirr-entai setup is illustrated in Fig. 1. The graphite end-section for the high temperature heater has an apron about 1/16 in. above the upper surface of the crystal. This apron insures that the surface temperature of the block is equal to or greater than the temperature within the block at every point, Thus, the zone does not penetrate the block and convection in the liquid is minimized. The experi-through a block is shown in Fig. 2,

Jan 1, 1958

By J. H. Westbrook, R. W. Guard

The influence of a number of alloying additions on the structure and hardness of Ni3Al (?') has been studied. Three general effects have been observed.. solid-solution hardening, strain aging, and defect hardening arising from deviations from stoichiometry. The solid-solution hardening phenomena are complicated relative to binary terminal solid solutions due to the possibility of virtually independent substitution for the component elements and to the concomitant effects of strain aging. In many superior nickel-base high-temperature alloys the elevated temperature strength is attributable to the presence of a dispersion of Ni3A1 (?') in a solid-solution matrix. Examples of such alloys are Inconel X-550, Inco 713, Waspalloy, and Nimonic 80. It is, therefore, appropriate to seek a further understanding of the properties and alloying behavior of this compound. Ni3Al, the compound most rich in nickel in the nickel-aluminum binary system, was first detected by litakal but not established with certainty until the much later studies of Bradley and Taylor' and Alexander and Vaughan.3 More recently the mechanism of formation was clarified by Floyd4 who showed that Ni3Al is the product of a peritectic reaction at 1395°C between the melt and the compound NiAl in agreement with the original suggestion of Alexander and Vaughan.3 Ni3Al has the ordered face-centered-cubic or Cu3Au structure in which the nickel atoms occupy the face centers and the aluminum atoms the cube corners, a0 = 3.570A. Despite earlier reports to the contrary. the compound apparently remains ordered at least to 1000oC.5 It exists over a narrow range of compositions (-3 pct wide) whose limits and temperature dependencies thereof have been reviewed recently by Taylor and Floyd.' Most previous workers have found Ni3Al to be both hard and brittle7,8 although Maxwell and Grala8 obtained 2.5 to 6 pct tensile elongation at room temperature and Alexander and vaughan3 described the material as "hard and tough" on the basis of observations made while preparing metallographic specimens. In a recent study one of the present authors found that although considerable intergranu-lar brittleness was evident: individual grains of a coarse-grained inert atmosphere arc-melted specimen were readily deformable.l0 The same study also showed Ni3Al to have an anomalous temperature dependence of hardness in that such a curve exhibits a number of peaks between room temperature and 800°C which could not be associated with any microscopically observable precipitation reactions or polymorphic transformations. It was, therefore, proposed in the present study to elucidate the anomalous high-temperature strength behavior and to examine the solid-solution alloying of this compound and the effects of such alloying on hardness. Sample Preparation and Experimental Procedure-Samples, both of pure Ni,Al and of various alloyed solid solutions based on Ni3Al, were prepared by arc melting 100-g buttons in an inert atmosphere arc furnace. All buttons were heat treated for 4 hr at 1275oC and examined metallographically for homogeneity. Microstructures were typically homogeneous and single phase with ASTM grain size about 1 and unusually clean grain boundaries. Chemical analyses showed good correspondence (within a few tenths of a percent) with intended compositions. Microindentation hardness data were obtained from room temperature to 800°C in vacuo using a balanced-beam type loading system in an instrument to be described in detail elsewhere." In general a 100-g load, a loading rate of 1 mm per min and an indentation time of 15 sec were used. Various indenter materials were used according to the materials bein tested because of specimen-indenter interaction. Fl Measurements of the Vickers-type indentations were made at room temperature. Hardness-temperature curves were run at least twice on each sample to ensure that surface work-hardening effects had been eliminated." Precision lattice-parameter measurements were made on powder samples using a back-reflection

Jan 1, 1960

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By William W. Adams

A larger measure of safety attended the operation of the stone quarries and related plants in the United States during the calendar year 1935 than in any other year for which annual records are available for the industry. The accident rate, covering fatalities and nonfatal injuries that disabled an employee beyond the remainder of the day on which the accident occurred, was 38.19 per million man-hours of work performed. The nearest approach to this favorable record was in 1932 when the rate was 38.48. The rate for 1934 was 41.82; hence the record for 1935 was 9 percent better than that for 1934. Reports from operating companies showed that 51 men were killed by accidents in 1935 and 4,152 men were injured. (See table 37.) The industry employed 73,005 men and performed 110,033,341 man-hours of labor, an average of 1,507 hours of work per man. Measured in man-days, the total volume of labor was 14,623,303, or an average of 200 days of 7.52 hours per day for each man employed. These figures are not strictly comparable with similar figures for the preceding year, as the, coverage of the industry was more complete for 1935 than for 1934 because special facilities were available to the Bureau of Mines for conducting the 1935 canvass that were not available for the 1934 canvass. Reports covering identical plants that were active both in 1934 and 1935 indicate a reduction of about 7 percent in the number of men employed in 1935. This fact suggests that the apparent increase in the number of workers in 1935 is attributable chiefly, if not entirely, to the more complete coverage of operating plants in 1935. The plants from which this inference is drawn employed 21,799 men in 1934 compared with 20,248 in 1935.

Jan 1, 1937

By Richard W. Knostman

A study was made of the factors affecting lead and zinc production in the Pacific Northwest. Costs, ore reserves and potential resources, and domestic demand were analyzed. It was concluded that a projected 3.1-percent average annual increase in U.S. demand for zinc through 1975 and a corresponding 2.5-percent rise for lead will be supplied mainly from mines in the Eastern and Central States. Annual Pacific Northwest mine production of lead is estimated to fluctuate around 82,000 tons, while zinc output may average 135,000 tons through 1975. Measured, indicated, and inferred reserves in the Pacific Northwest, containing 1.56 million tons of lead and 2.59 million tons of zinc, are more than sufficient to maintain this level of production. Annual production from Pacific Northwest electrolytic zinc plants is expected to increase to over 300,000 tons of slab zinc by 1975. Lead smelters may experience difficulty in maintaining output at 1964 levels.

Jan 1, 1967

By M. Buchmann, T. Mütze, F. Heinicke

Dry air classification is a well-known technique used for decades in the cement industry to separate material in the size range of 0.01-1.0 mm. Additionally, in corresponding dry grinding circuits with effective machines such as High Pressure Grinding Rolls (HPGR), the energy consumption can be reduced compared to wet applications. These dry systems are not state of the art in minerals processing plants, but first prototypes have been installed and an increasing number of projects are starting to evaluate this option. One challenge in this field is the mineral composition of ores, which have, by far, a higher variety in density and size than those of cement. High density particles such as iron- containing ones have higher settling rates than low density silica particles of the same size. The main question to answer in this paper is how to evaluate this effect, so a quantitative method using Mineral Liberation Analyses was developed to calculate two-dimensional partition curves. Additional statistical analyses allow for isolation and quantifying the interaction of density and size, enabling engineers to consider this effect for the sizing of process plants. The paper will present the method and selective results for a compounded ore of iron and silica. Keywords: HPGR, air classification, partition curve, MLA

Jan 1, 2020

By L. Thomassen, N. Spooner, J. M. Thomas

NI-CR and some Ni-Cr-Fc alloys, when used as electrical resistance heating elements in reducing atmospheres, at times suffer rapid breakdowns due to so-called "green rot." These reducing atmospheres are most frequently used in bright annealing and heat-treating furnaces which are kept for long periods of time at 1500' to 1800°F. The green rot is a preferential oxidation of the chromium in the alloy to such an extent that the remaining metal frequently becomes ferromagnetic. The Curie point (magnetic transition point) at room temperature for a pure Ni-Cr alloy is known to be at about 7 pct Cr.¹ This represents a severe loss in chromium for one popular grade of resistance alloy, which is nominally 80 pct Ni-20 pct Cr. The formation of oxides along the grain boundaries makes the ribbon brittle and gives the fracture a green, earthy appearance—hence the name. The authors have studied this phenomenon, simulating the industrial conditions by heating resistance ribbons in various reducing atmospheres, such as moist hydrogen or the atmosphere specified in the ASTM test.² This atmosphere contains 16 pct H2, 10 pct CO, 4 pct C02, 1 pct CH1, 1.5 to 2.5 pct H2O, balance N2. Little success was had in producing severe corrosion with the commercial 80 pct Ni-20 pct Cr alloys. It had been noticed, however, that 90 pct Ni-10 pct Cr alloy wires deteriorated very rapidly when placed in the bottom of narrow thermocouple protection tubes. The bottoms of the tubes with the wires were heated in air. This took place both in porcelain tubes and in Inconel* tubes either with the cold end open or loosely stoppered with asbestos. On examination the wires showed microstructures which would be classified as green-rot corrosion. Subsequent investigations with various alloy wires confirmed the observation that corrosion occurred in some wires, including 80 pct Ni-20 pct Cr alloys, much more rapidly in such tubes than had occurred previously in test atmospheres mentioned above. When 90 pct Ni-10 pct Cr alloys are oxidized with an abundant air supply, the oxide coat consists of both nickel and chromium oxides. In this case thermodynamic equilibrium between the oxides is not established. However, when oxidized 90 pct Ni-10 pct Cr alloy specimens were heated to 1500" to 1800°F inside small diameter tubes, the oxide coat transformed to a bright metallic outer layer of nickel or nickel-rich alloy, beneath which appeared a green oxide, followed by intergranularly attacked metal. The obvious explanation is that in the narrow tubes, thermodynamic equilibrium is being established according to the equation NiO + Cr (in alloy) ? Ni + Cr2O3 This reaction is favored due to the fact that the oxygen pressure over nickel oxide is more than 10"' times the oxygen pressure over the green chromium oxide. The initial oxygen in the tubes is depleted very rapidly by oxidation of the wire and of the tube, if it is metallic. A confirmation of the occurrence of the reaction, reduction of NiO by the chromium in the alloy, was obtained by putting oxidized nickel foil into an evacuated quartz tube along with a piece of bright 90 pct Ni-10 pct Cr alloy ribbon, and heating the tube at 1820°F for a number of hours. The nickel oxide on the foil was completely reduced to pure nickel, leaving a bright foil. The 90 pct Ni-10 pct Cr alloy became strongly magnetic and showed the typical green-rot structure. Weights of the samples before and after testing showed the weight loss of the foil to approximately equal the weight gain of the ribbon. Evidently the bottom of long, narrow protection tubes, stoppered or not, may under certain conditions act just as the sealed quartz tubes in respect to being a confined space in which oxygen is not freely replenished. This condition of oxygen depletion can be prevented by introducing a small amount of air into the bottom of the tube. Many conditions becloud the green-rot phenomenon, such as carburization, sulphidization, and the presence of other corrosive agents. However, these experiments have shown that the basic reaction is a case of internal oxidation which can occur simply by adjusting the oxygen pressure to a low enough level so that the atmosphere will leave the nickel intact and oxidize the chromium. The action of the other agents in commercial atmospheres can then be taken up as individual cases. From these and numerous other tests completed to date or still in progress, it is believed that a more critical evaluation of electrical resistance alloys for their resistance to green-rot corrosion can be made. A much better understanding of the mechanism for this type of corrosion should also result. A more complete report on these experiments will be published later. In the May 1953 issue: TP 35213 Discussion: Solubility of Carbon and Oxygen in Molybdenum by W. E. Few and G. K. Manning, discussion by N. A. Gokcen: p. 747, first column, the fifth, sixth, and seventh lines should be the first, second, and third lines, followed by the present first, second, third, fourth, eighth, ninth, and tenth lines.

Jan 1, 1954

By Wenya Du, Qingbo Yu, Peng Li, Qin Qin

"A new heat recovery system is proposed. This system uses the endothermic heat of gasification reaction instead of sensible heat to recover the energy of molten blast furnace slag. The gasification technological parameter in molten blast furnace was calculated and the exergy of the system was analyzed. The gasification reactions were studied kinetically by the isothermal thermogravimetry using STA409PC thermal analyzer. The results showed that, according to different gasification agent, this system can produce syngas with different C-H ratio. The exergy efficiency of this system is high and its internal exergy loss rate is about 11%. This method can bring huge economic and environmental benefits which are important to the survival and sustainable development of iron-steel enterprises. The molten BF slag acts as not only thermal media but also good catalyst. The kinetic parameters on gasification reaction with different types of coal used differ from each other.IntroductionEnergy consumption in the iron-making process is about 50%~60% of the total energy input. The blast furnace is very important in the iron & steel process. So energy conservation and emission reduction about blast furnace is very important. In recent years, in order to recovery energy, many new technologies such as TRT (Top gas pressure Recovery Turbine) and CCPP (Combined Cycle Power Plant) were used in iron-making. But the energy of molten blast furnace (BF) slag has only been used limitedly so far.Molten BF (Blast Furnace) slag is the byproduct of iron-making at the high temperatures range from 1723 to 1923K, and has a large amount of sensible heat remaining. The yield of molten BF slag is about 300 kg per ton of pig iron. In conventional processes, molten BF slag is quenched rapidly using a large amount of water to produce a glassy-granulated slag. The quenching slag must be dried before it can be used in cement manufacture. During the process, a large amount of water was consumed and the energy of molten slag can not be recovered. At the same time, it causes environmental pollution problems. So the critical problems of the process are not only energy recovery of molten slag and reducing emission of H2S and SO2, but also guaranteeing the subsequent use value of slag. For this propose, many new technologies were investigated to recover the thermal energy of molten slag. The promising methods are dry granulation [1-4] and reforming of methane [5-9]. The method, utilization of reaction heat instead of latent heat and sensible heat, is quite attractive from viewpoints of energy storage without heat loss, and makes a connection to other industry. But both of them are in laboratory. In this paper, coal gasification in molten BF slag was used to recover the energy of molten BF slag. The gasification technological parameter in molten BF was calculated and the exergy of the system was analyzed. The gasification reactions were studied kinetically by the isothermal thermogravimetry using STA409PC thermal analyzer."

Jan 1, 2011

By Douglas J. Harvey

The surface tension of lead-tellurium alloys (in the range 0 to 6.70 at. pct Te) ad lead-arsenic alloys (in the range 0 to 10.53 at. pct As) has been examined by the maximum bubble pressure method. The surface tension of high purity lead can be expressed over a range of temperatures (M.P. to 750°C) by the relationship = 512 — 0.133t. Arsenic and lellurium were both found to be surface active in lead. The surface excess concentration at 700°C was .found to be constant at 0.74 x 10-10 moles per sq cm for tellurium. The surface excess of arsenic at 700°C varied between 0.26 x 10-10 moles per sq cm at 0.16 at. pct to 1.5 x 10-10 moles per sq cm at 8.3 at. pet. The surface tension of lead has been investigated sporadically over the last 90 years. The first recorded study was made by Quincke1 who used a rather crude application of the drop-weight method. Hogness2 obtained the first reliable value for the surface tension of lead by measuring the pressure necessary to force the liquid metal from the end of a small capillary of known radius. Hogness gives the empirical formula: ?(surface tension)= 444 - 0.077 (l-327) which describes the relationship between surface tension and temperature ("C); This work was followed by that of Bircumshaw3 who applied the two-capillar maximum bubble pressure method of Sugden.4 The values published by Bircumshaw are in good agreement with those found by Hogness. Matuyama5 examined the surface tension of lead by the drop weight method. However, the values found are somewhat higher than those previously reported. More recent investigations by Greenaway6 and by Melford and oar' have resulted in data which are not in close agreement, but which are well within the expected range at most temperature levels. The study of the surface tension of lead alloys began with Drath and sauerwald8 who examined the lead-bismuth system. They found that the surface tension values of the alloys in this system deviated only slightly from the ideal mixture rule. Matuyarna5 examined the lead-antimony system. Bircumshaw the lead-tin, and the lead-indium system was studied by Hoar and Me1ford.10 The results of these investi- gations are summarized in Fig. 1. It may be seen that the data vary only slightly from the ideal mixture rule. As none of the metals studied and reported in the literature has a very interesting effect on the surface tension of lead,*the next logical step might be to examine the effect of metals of low solubility or nonmetals having some liquid solubility. Baes, and Kellogg11 have pointed out that the elements most likely to be surface active in liquid metals are ones of limited solubility in the liquid state and possessing weak intermolecular bonding forces in the solid state. Therefore, Group V, VI and VII nonmetals are most likely to be surface active. It was decided to examine the effect of a borderline metal, arsenic, and a nonmetal tellurium. Arsenic forms a eutectic with lead having a melting point of 290°C and a composition of 6.9 at. pct As.13 Pure arsenic sublimes when heated above 610°C. Even though alloying with lead lowers the vapor pressure, fumes containing arsenic are evolved at a very noticeable rate when lead-arsenic alloys are heated above 650°C. Tellurium raises the liquidus temperature of lead sharply to 904°C,14 the melting point of PbTe (lead-telluride). The solid solubility of tellurium in lead was determined by Greenwood and worner15 to be 0.0007 at. pct at room temperature. EXPERIMENTAL METHOD Surface Tension Measurement—The two capillary maximum bubble pressure method for measuring surface tension developed by Sugden,4 and used later

Jan 1, 1962

By Owen Matthews

THE property of Cochenour Willans Gold Mines, Limited, is in Dome township, Red Lake area, northwestern Ontario, a hundred miles north of Kenora and close to the Manitoba border. 'Planes of Canadian Pacific Air Lines, Limited, serve the district daily, except Sundays, from Kenora, Ontario, and Lac du Bonnet, Manitoba, passengers being trans-ported from Winnipeg to Lac du Bonnet by car. Freight is handled by the Patricia Transportation Company. It is brought in from Hudson, Ontario, on the Canadian National railway, in summer by water and in winter by tractor trains over the frozen lakes. The first staking on the property was done during the 'rush' of 1926 and 1927 by William M. Cochenour, and on April 30th, 1928, a syndicate was formed, taking in claims of W. M. Cochenour and Dan Willans and H. G. Young. Surface trenching was carried on almost continuously until 1934. In October, 1932, Ventures Limited took an option on the property, and in December of that year they carried out an extensive diamond drilling programme, but considering the results did not justify further work, they relinquished the option. In July, 1934, further surface work was carried out under the supervision of W. P. Mackle and, on the strength of his report, Noah Timmins Incorporated took an option on the property and agreed to make an initial expenditure of $100,000 on development work. This was carried out under the direction of Hollinger Consolidated Gold Mines and included the sinking of a shaft to a depth of 165 feet, establishment of a level at the 150-foot horizon, and some 1,900 lineal feet of drifting and cross-cutting. The results obtained from this work were not considered of sufficient promise and the option was terminated in August, 1935. Mr. Cochenour then approached Alex Mackenzie and associates, and the present Company, Cochenour Willans Gold Mines, Limited, was organized on April 9th, 1936, and sufficient money was raised to continue operations. Under the direction of W. P. Mackle, the shaft was deepened and a second level was established at the 275-foot horizon; but, due to several adverse reports by outside engineers, it was found impossible to raise sufficient money to carry on the work and operations were suspended in December, 1937. In January, 1939, an agreement was entered into with Gold Eagle Gold Mines for the milling in their plant of some Cochenour ore. A total of 4,959 tons was treated, and the results were so encouraging that further finances were raised by C. A. Gentles & Company, of Toronto. Following further development in the mine, it was decided to erect a mill. Construction was started on September 1st and the mill was turned over on November 29th. The first gold brick was poured on December 23rd.

Jan 1, 1942

By Rob Jameson

"The demand for commercial and residential construction has continued to evolve across the United States over the last decade. Our markets demand larger, deeper and inherently more complex structures, located within increasingly constrained urban locations and with challenging geotechnical conditions. As project demands incrementally escalate, specialty contractors are continuously challenged to extend their state of practice. Development in the size and capabilities of construction equipment, tooling, techniques, monitoring and verification systems over the last decade has consistently allowed contractors to build larger and deeper. For support of excavation (SOE), in addition to scale, selection of the most appropriate system has been a key to success in the most challenging ground conditions. This selection process is based on sound engineering and construction practice, and also prior experience, both positive and negative. Ultimately many Owners have chosen to manage their risk of SOE construction through design-build contracts, which allows specialty constructors to optimize the balance of cost, schedule, scope and associated risk based on their local expertise. Successful implementation of a design-build methodology begins long before a contractor is selected, with identification of key project requirements and risk factors during the feasibility studies and design development phases. In these early stages of the project development, advice and budgets are frequently solicited from Specialty Contractors. The Owner, Construction Manager and Consulting Team will filter this input from multiple sources to provide their specific recommendations, develop construction documents and select the appropriate form of contracting. Only in the final stages, after award of a Design-Build Subcontract, can the successful specialty contractor directly influence risk management approach on the project. A case study is presented from Block 9 in San Francisco’s Transbay District. This project demonstrates the incremental identification, assignment and mitigation of construction risk through the planning and design build process for SOE on the deepest planned excavation in San Francisco.INTRODUCTIONThe mature urban development market in United States results in high demand for complex Support of Excavation (SOE) schemes on constrained sites. The Design-Build approach can be applied to increasingly difficult SOE challenges, combining regional specialty subcontractor knowledge and experience in order to optimize solutions for cost and schedule. The most successful applications will involve early engagement of shoring subcontractors within the project teams, during feasibility and design development stages, in order to identify key scope and risk issues, and their potential solutions. Throughout the project development, it is important to reasonably assign responsibility for construction risks amongst the project stakeholders who are best able to control them.This paper presents a case history for San Francisco’s Block 9, a well-planned and successfully executed design-build SOE project in San Francisco’s Transbay Redevelopment area. Throughout the 4 year period from the Developers initial proposal to the Redevelopment agency, through completion of excavation down to subgrade, the project team developed a series of increasingly refined SOE schemes, with corresponding scope definition and cost and schedule estimates. This program relied on early identification of key challenges and risks for the project, and evolved through multiple phases of proposals as first the General Contractor (GC) and then Specialty Shoring Subcontractor were engaged for the project. The scheme, cost and schedule refinements continued throughout construction in order to accommodate unanticipated conditions and events as they unfolded."

Jan 1, 2017

By C. Tan, C. Detournay

Wellbore stability is a major concern for drilling in naturally fractured formations. The infiltration of drilling mud into the fractures is a factor, which may compromise wellbore integrity due to the loss of strength experienced by the fractures. The reduction in the fracture frictional and cohesive properties is attributed to weakening of the infill materials and lubrication of fracture asperities by the mud filtrate. One way to investigate the influence of mud infiltration on wellbore stability in fractured formations is to use a numerical modeling approach. A requirement for the numerical model is the ability to predict the region of mud infiltration. This paper describes a numerical technique to model the extent of mud infiltration for application in coupled fluid-mechanical simulations in densely fractured rock masses using the computer code, UDEC. Several factors are considered including fracture pattern, in-situ stresses, reduction in joint frictional angle and cohesion, viscosity of the mud filtrate and fracture plugging. Results of numerical simulations are presented to illustrate the technique and show the influence of these factors on the extent of mud infiltration. Un des problèmes importants posés par le forage en milieu fissuré saturé, est celui du maintient de la stabilité du puit. L’infiltration de boue de forage dans le massif peut avoir pour effet de réduire les propriétés frictionnelles et cohésives des fractures et de compromettre ainsi la stabilité du puit de forage. Le radoucissement des propriétés des fractures est attribué à la dégradation du materiau de remplissage et au pouvoir lubrifiant des boues. L’analyse numérique offre un moyen d’investiguer l’influence jouée par l’infiltration de boue sur la stabilité du puit. Un des critères de sélection du modèle numérique sera son pouvoir de prédiction du domaine d’infiltration de boue. Cet article décrit une technique numérique permettant de modéliser l’infiltration de boue de forage dans le cadre de simulations hydro-mécaniques, en milieu à haute densité de fractures, effectuées avec le logiciel de calcul UDEC. Parmis les facteurs tenus en compte, on trouvera la nature du réseau de fractures, les contraintes in-situ, le radoucissement en friction et cohésion des joints, la viscosité de la boue et le bourrage des fractures. Des résultats de simulations sont présentés pour illustrer la technique et montrer l’influence de ces facteurs sur la taille du domaine d’infiltration de boue. Bohrlochstabilität ist ein wichtiger Aspekt für das Bohren in geklüfteten Gebirgsformationen. Das Eindringen der Bohrlochstützflüssigkeit in die Klüfte kann die Bohrlochintegrität wegen des Verlustes der Festigkeit des Kluftsystems gefährden. Die Reduktion der Reibung und kohäsiven Eigenschaften ist der Schwächung der Kluftfüllung und der Schmierwirkung der eingerungenen Stützflüssigkeit in Bezug auf die Kluft-Asperities geschuldet. Numerische Berechnungen sind ein Weg zur Untersuchung des Einflusses der Infiltration der Bohrlochstützflüssigkeit auf die Bohrlochstabilität in geklüfteten Gebirgsformationen. Eine Voraussetzung für numerische Modelle ist die Fähigkeit den Bereich der Infiltration der Stützflüssigkeit zu prognostizieren. Diese Publikation beschreibt ein numerisches Verfahren, um die Reichweite der Infiltration von Stützflüssigkeiten mittels fluid-mechanisch gekoppelter Simulationen im engständig geklüfteten Gebirge mit dem Programm UDEC zu modellieren. Verschiedene Faktoren, wie Kluftmuster, Gebirgsspannungszustand, Reduktion von Kluftreibungswinkel- und kohäsion, Viskosität der Stützflüssigkeit und Rissabdichtung wurden untersucht. Ergebnisse numerischer Simulationen werden präsentiert, um die Vorgehensweise zu illu

Jan 1, 2003

By R. Hogg, S. Chander

"An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example in development of new processes, plant and process design, plant control, problem solving, etc. IntroductionThe behavior of particulate systems, in mineral processing and other applications, is primarily affected by the physical characteristics (size, shape, surface area, pore structure) of the particles and the nature of the different solid-fluid interfaces present. Mineral processing operations in general are either designed to modify and/or control physical and interfacial properties (grinding, classification, agglomeration, etc.) or are strongly influenced by them (flotation, flocculation, solid/liquid separation, etc.). Characterization of physical and interfacial properties should be an integral part of the development of new processes, plant and process design, and routine plant operation.Our purpose in preparing this article has been to present an overview of the current status of characterization, to point out areas of weakness, and to discuss the reliability and limitations of the various techniques, procedures, and instrumentation available. For more detailed discussion of methods, etc., the reader is referred to standard references.Sampling particulate solids.Sampling is a critical factor in any procedure for characterizing particulate materials — the reliability of characterization data is ultimately limited by the extent to which the sample used was truly represen¬tative of the population from which it was taken.Sampling from particulate solids involves two basic problems: (1) the selection of a random', unbiased sample and (2) choice of the appropriate sample size.The problem of sample selection involves the design of a sample collection procedure that ensures that every kind of particle in the population has the proper chance of being included in the sample without bias. Specific procedures such as the well-known cone-and-quarter technique have been developed and are discussed at length in the literature on particle characterization (Allen, 1981: Herdan, 1960: Gy, 1982)."

Jan 1, 1989