Search Documents

By A T. Spathis, M G. Wheatly

Some preliminary dynamic pressure data were obtained from several charges detonated in a tunnel situated in massive granite rock. The context of the work is the potential for desensitisation of explosives, failure of detonators, and sympathetic detonation due to the close proximity of inter-hole and inter-deck explosive charges to each other. Dynamic pressures were measured using piezoelectric gauges in water-filled 45 mm diameter holes adjacent to the charges. Some of the first arrival peak pressures were noisy, and although not fully resolved, may be due to reflections and the physical arrangement of the transducers and their size with respect to the monitoring holes. The estimated peak pressures were between 0.1 to 8.7 MPa at approximate distances of 2.8 to 0.8 m, respectively. Further work is planned with gauges that are disposable, have a higher pressure range, and can be used within a few borehole diameters rather than the piezoelectric gauges used in the present work.

Jan 1, 2016

By Chas. G. Maier

The absence of plants on the Pacific coast for the reduction of iron ores usually is attributed to the fuel situation there. Thus, the bulletin of the. State Division of Mines for 1933, entitled "California Mineral Production," says: "There are considerable deposits of iron ore known in California, notably in Shasta, Mad era, Placer, Riverside, San Bernardino, and Los Angeles Counties, but production has so far been limited for lack of an economic supply of coking coal." It has been estimated that the six major steel plants of the Pacific coast have an annual ingot capacity of 600,000 tons. The present need for tin plate averages 300,000 tons yearly for California alone, of which some 12 percent is manufactured locally. If the consump¬tion of other iron and steel products in 1929 may be taken as an approximate, estimate of the normal requirement for such products, it may be estimated further that, 65,000 to 75,000 tons each of cast-iron pipe and steel reinforcing bars and 300,000 to 400,000 tons of structural shapes and plates will be required annually in California.

Jan 1, 1936

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By E. F. Adkins, R. W. Douglas

The variation of the spectral emissivity of osmium and ruthenium with temperature can be expressed by the following relations: DURING a study of the sintering characteristics of osmium and ruthenium, discrepancies in the previously accepted melting points of the metals were noted. The melting temperatures had not been measured at the time of the work, but were estimated in the literature as 2700°C for osmium and 2450°C for ruthenium.' A recent investigation by Baird2 has shown the melting temperatures of osmium and ruthenium are 3000" and 2250° C, respectively. In the present work, osmium bars sintered at temperatures as high as 2900° C showed no evidence of melting, whereas ruthenium showed definite evidence of melting at temperatures as low as 2250°C. In view of the apparent discrepancies, the melting temperatures of both metals were determined. The spectral emissivities of both metals were determined as an aid to studies of the sintering characteristics of these metals. MATERIALS AND PROCEDURES The materials used in these studies were metal powders supplied by Englehard Industries, Inc., through the courtesy of The International Nickel Co. Analytical data from three laboratories, although not in complete agreement as to the purity of the material or the major impurity elements, indicated that the maximum impurity levels were 0.5 and 1.0 wt pct in osmium and ruthenium, respectively. The metal powders were pressed to 1/4 by 1/4 by 6-in. bars at 20Tsi using carbon tetrachloride as a lubricant. The pressed bars were presintered 1 hr at 1200°C after heating 1 hr at 400°C. The presintered densities of the several bars of the metals ranged from 65 to 80 pct of ideal density. Specimens were self-resistance heated in a vacuum sintering bell. Temperatures were measured with an L&N, disappearing filament optical pyrometer. True temperatures were read at the base of an 0.30-in.-diam, 0.150-in. deep hole drilled into the center of a presintered bar. Apparent temperatures were read from the surface of the bar adjacent to the hole. MELTING POINT DETERMINATION The melting temperature of the metals was determined as the temperature at which a slight additional increase in current through the specimen resulted in a reduced temperature at the base of the hole. The apparent reduction in temperature is a result of the liquid metal filling the hole, thus altering the black-body conditions. The melting points of osmium and ruthenium, based on three deter-

Jan 1, 1962

By W. E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential."

Jan 1, 2002

By R. D. Leitch

"REASONS FOR AND PURPOSE OF WORKIn 1924 the United States Public Health Service was requested to undertake a special study of stream pollution. At that time the proposal that the United States Bureau of Mines take up the study was made by the Public Health Service because in point of training and experience the personnel of the latter was considered not to be as well, suited to this type of investigation as was that of the Bureau of Mines. H. Foster Bain, then Director of this bureau, promised to undertake the work, and, accordingly, field investigations were begun in the spring of 1925. The problems of mine-drainage wastes and of gas-house and coke-oven waste were investigated in the laboratory, and a method of treatment by sodium hydrate and benzol was found to be promising. The idea was obtained by A. C. Fieldner, chief engineer of the Bureau of Mines experiment stations, while in Germany in 1924, where he was shown a practical application of the process, but no information was obtained as to definite chemical or mechanical processes. Because of the then pending American patent application by the German firm, we made no attempt to develop our findings further. Shortly after, a similar method of treatment was developed in the United States, and since that time we have devoted our attention entirely to mine drainage. This paper is a presentation of some general facts and information gathered during the past five years on coal-mine drainage.SCOPE OF WORKAt the time our work was begun there was such a diversity of opinion on the whole subject and apparently so little was accurately known, that it was decided to undertake a basic study from which (1) certain definite information might be evident, and (2) what might be considered side issues of the original investigation would be suggested for subsequent study.A stream in a district thought to be representative of those in low to average sulphur bituminous coal fields and another in a high sulpbur district were selected for study, A fair (weber of factors entered into the tentative selection of these streams, the chief ones being their accessibility and freedom from other industrial or domestic pollution, besides, of course, the presence of mine drainage in these streams."

Apr 1, 1931

By Luis F. Morán

El presente texto señala algunos aspectos que comprende el proyecto de San Nicolás desarrollado por Marcona Mining Company. El proyecto señala las facilidades de la mina, transporte, almacenamiento del mineral, plantas chancadoras, lavado y concentración por medio denso, concentración magnética, instalaciones para almacenar productos comerciales, formación de pellets verdes, endurecimiento, terminado y control del proceso.

Jan 1, 1965

By E. D. Doney

The Kerr-McGee Coal Corporation's Galatia Mine's first longwall mining system was implemented on May 3; 1989. Start-up of the longwall face represnted the successful conclusion of an effort begun nearly four years earlier. This paper-presents a case history of the processes that led to the longwall's implementation, and the subsequent mining of the first 7,900 foot long panel.

Jan 1, 1990

By CHARLES R. KETES

I. INTRODUCTORY. INDUSTRIALLY, the most important service that geological science can now render to mining in the Upper Mississippi leadand zinc-fields is to devise some practical scheme whereby the productive ore-belts may be located with greater certainty than they have been in the past. Up to the present time there has been little service of this kind, and in spite of all that has been worked out concerning the geologic features of the region, and notwithstanding all that has been written about these ore-deposits, this particular phase of the subject has been, for some reason or other, the very one that has received the least consideration. The neglect by geologists in this respect has been all but complete. The following notes are suggestive of some practical solutions to the problems presented. As here suggested, the geologic relationships of the ore-bodies were surmised some years ago, though somewhat vaguely perhaps. No opportunity for securing critical data appeared until recent investigations of a private character were undertaken, which bad in view the extensive prospecting of undeveloped areas. Fresh from rather wide experiences of a decade in the principal mining-regions of four continents, and after a lenstrum's residence among the chief mining-camps of the West and of Mexico, under conditions which measured geologic hypotheses in meters and rigidly tested their values in, terms of dollars, the recent return to the Joplin field and a new survey of its ore-conditions were fraught with somewhat unexpected results. Aspects of the ore-deposition were presented of which previously there was no hint. Ten years' absence from the district had tended greatly to clarify former hazy impressions. It enabled many features, then only dimly outlined, to be considered more nearly in their true perspective and in their real relationships to their surroundings. It permitted a great mass of details collected a dozen years before in connection with the work of the Missouri Geological Survey to be viewed under new light and to

Feb 1, 1909

By AIME AIME

AS a new departure the annual business meeting was held at 4 p. m. on Tuesday, Feb. 16, instead of in the morning, as previously. The retiring President, Robert E. Tally, called the meeting to order and briefly spoke of the large measure of success that had been attained in balancing the budget of the Institute in 1931, so that, although receipts had declined over $26,000 compared to the previous year, expenditures had come within $3,000 of income. He referred in complimentary ,terms to the work of the committees on Membership, Admissions, Papers and Publications, and MINING AND METALLURGY, from which more would be heard late:. He also announced that a large and important committee on economics has been under consideration, and will be announced later. As an evidence of growth it was noted that a new Division, Mineral Industry Education, had been organized just an hour previously.

Jan 1, 1932

By P. Lind, A. Gagnon

"Goldcorp has embarked upon an ambitious, industry-leading, multi-year water use reduction effort. This is a proactive, voluntary effort that reflects our commitment to truly sustainable mining. This effort will focus on increasing water re-use and recycling, and reducing water inputs ultimately towards zero. All of our operating mines are expected to contribute to this effort and are currently in the process of developing plans to meet short and long term objectives. One of the largest needle movers to increase water re-use and recycling is in the area of tailings management. Within five to ten years at Goldcorp, it is envisioned that the need for wet tailings dams will be eliminated and that all new tailings facilities will consist of only filtered or dewatered tailings. Filtered tailings is developing into a mature technology with wide application in mine waste management. This paper describes a conceptual level evaluation on the transition from a slurry to a filtered tailings operation at the Cerro Negro mine in southern Argentina. Key benefits and challenges are highlighted.INTRODUCTION Goldcorp’s Cerro Negro operation is located in the Santa Cruz province in the Patagonian region of Argentina. Cerro Negro has been in operation since 2014 and commercial production was achieved on January 1, 2015. The processing capacity of the plant is 4,000 tonnes of ore per day and in 2016 produced 363,000 ounces of gold and 3.1 million ounces of silver (Goldcorp Inc., 2017). As the mine is located in a semi-arid area, it is important to evaluate technologies that could reduce freshwater consumption and maximize water re-use and recycle rates. The current tailings operation at Cerro Negro incorporates pumping of tailings slurry into a conventionally lined Tailings Storage Facility (TSF). Water is reclaimed from the tailings supernatant pond to the process plant via pumps, however, water losses occur due to evaporation and solution retention within the slurry tailings voids. Converting to a filtered or dewatered tailings operation would allow for increased water recovery prior to tailings disposal, and decreased water losses from evaporation and from retention in the tailings solids void space. This paper describes a conceptual level evaluation on the transition to filtered or dewatered tailings with the primary objective of moving closer Towards Zero Water."

Jan 1, 2017

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60 percent and 40 percent, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert, and a rigid insert for cleaning the roof bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the coveralls when using either of the inserts.

By T. W. Wlodek

"AbstractSatisfactory mine drilling operations depend on the good performance of the drilling machine, and of what may be called the drill set, i.e., the following four elements: bit, attachment, drill rod, and shank end. The field performances of these four elements in the drill set are analysed and their service lives are compared. The most .common causes of service failure are reviewed and possibilities of increasing service life are discussed.The laboratory methods now employed for the simulated service testing of tungsten carbide bits, conical push-on and threaded .types of attachments, drill rods, and shank ends are described, and some results are discussed. The objectives of the research programme now being carried out •on the above mentioned elements are outlined.A number of mines in British Columbia, northern Ontario, and northern Quebec have been visited, and, with the co-operation of the C.I.M. Branches in these areas, meetings with representatives of the mining and steel industries concerned have been held. In this paper, the mechanical-metallurgical problems most frequently encountered and discussed during these visits and meetings are described and .analysed.IntroductionSUCCESSFUL mine drill operations depend to a great extent on• the satisfactory field performance of the four elements which form the mining drill set, shown diagrammatically in Figure 1.These important elements are:1. -The bit, which may be one of the following types:(a) Detachable tungsten carbide bit( b) Inserted rod bit, so called chisel bit( c) Detachable steel bit( d) Solid rod bit"

Jan 1, 1952

By R. Costantini

The author discusses the promising future of the use of pipelines for transportation of ore slurries over long distances, citing existing installations. Various criteria and factors affecting the use and size of pipelines are considered. Among the factors influencing the use of pipelines are particle size, specific gravity, abrasiveness, minimum velocities, and pumping considerations. Long-distance transportation of solids by hydraulic pipelines holds the promise of great economic benefits. Today within the confines of most mineral processing plants, the moving of solids about in slurry form by pipeline is commonplace, since the method offers great advantages when conditions are suitable. Yet, this method is surprisingly slow in being adopted on a broad scale for transportation of solids over long distances (arbitrarily the term will be applied to one over five miles long). This is especially surprising in view of the successful realization in this country within the last five years of two daring ventures in long-distance solids pipelines. A 72-mile long, 6-in. diam pipeline of the American Gilsonite Co. has been satisfactorily transporting 700 tpd of gilsonite from the mine at Bonanza, Utah, to the processing plant at Grand Junction, Colo., since April 1957. The 108-mile long 10-in. diam pipeline of the Pittsburgh Consolidation Coal Co. has been transporting about 4000 tpd of finely crushed coal from the mine at Cadiz, Ohio, to the Eastlake power plant of the Cleveland Electric Illuminating Co. on Lake Erie since January 1958. However, besides two projects in the operations of The Anaconda Co. there have been hardly any other significant solids pipeline developments in the minerals industry during the last three years. The two projects are the 14-mile long, 6-in. diam copper concentrate gravity pipeline at Anaconda's El Salvador project in Chile which has been transporting about 800 tpd since January 1959. The second is a 16-in. diam tailings pipeline at the Anaconda Reduction Works, Anaconda, Mont., designed to transport about 20,000 tpd of deslimed flotation tailings for dam building. This pipeline, which is currently undergoing tryout tests and which will be about seven miles in length, will have a maximum of three 20-in. rubber-lined centrifugal pumps in series at the starting point, each developing a maximum of 100 ft of head, to supplement gravity. It is the writer's opinion that the major reason for the hesitation in considering pipeline operations is confusion due to an inadequate understanding of the basic physical principles affecting the slurry flow process by many engineers in the industry. This in turn begets an attitude of fear and trepidation instead of confidence on the part of many management executives, which leads to a minimizing of the advantages and exaggeration of difficulties when considering the possibility of a long-distance solids pipeline. The promotion of better understanding and consequently the promotion of greater confidence in the potentials of long-distance solids pipelines when conditions are suitable is thus the main purpose of this article. To this end, after considering several examples of the possibilities for solids pipelines in the minerals field, the relative significance of the major factors affecting pulp flow, and some major aspects of slurry pumping will be discussed on a general qualitative level. Then a brief outline of the semi-empirical quantitative methods developed to date for estimating slurry flow behavior will be presented. SOME POSSIBILITIES To give an idea of the magnitude of the possible economic benefits, it should be interesting to mention briefly some of the projects currently under consideration and to suggest some likely future possibilities. At Anaconda's El Salvador Project in Chile (Fig. 1) it is eventually planned to extend the existing 14-mile pipeline by another 60 miles to bring the copper concentrates down to the coast of the Pacific Ocean. Preliminary tests indicate that the projected 6-in. pipeline will be able to transport approximately 2000 tpd of concentrates at a pulp density of 40 to

Jan 1, 1961

The La Colosa, Colombia porphyry gold deposit is currently in the pre-feasibility stage. This large deposit has many types of gold mineralization: native gold, electrum, and tellurides. These variations in the gold mineralization lead to variability in the gold recovery. The final process flowsheet may include gravity concentration with cyanide leaching. Metallurgical testwork is utilized to identify the zones of ore that may be problematic to recover. To help select the samples that represent the fluctuating variability zones, geometallurgical models are constructed using mineralogy and geology data. These zones are then wireframed and compared to the geological and structural models for spatial correlation. Samples for the variability testwork will be selected from these different zones to identify and analyse the effect the different gold mineralization types have on the recovery. By using geometallurgy to aid in the sample selection for metallurgical testwork, the variability in the ore body can be understood and constrained to aid in process optimization.

Feb 27, 2013

Two small coral islands in the Pacific Ocean, situated close under the equator, and formerly classed among the Line Islands, have, during the last three or four years risen into prominence owing to the valuable deposits of phosphate of lime discovered on them.The deposits of Ocean and Pleasant Islands are under the control of the Pacific Islands Company (1902) Limited, of London and, Sydney, and the high grade of the phosphate, together with the exceptionally favourable facilities for mining this mineral, of which there are several millions of tons on these islands, give this company advantages which enable them to command the Australian and New Zealand markets, and also to make large contracts with Japan and other countries. Both islands, as far as surface indications are concerned, are entirely constructed of coral, with phosphate on the top from the highest points to the present sea level, there being no sign of volcanic rocks, with the exception of a few pieces of drift pumice on the coast.Banaba (Paanopa according to. the Admiralty charts), also known as Ocean Island, was discovered in 1804. It is situated in lat. 0° 52" S. and long. 169P 3[)" E.

Jan 1, 1904

By William Gleason

The Society for Mining Metallurgy and Exploration (SME) has a long and proud history of being the world?s leading resource for the dissemination for technical information regarding the fields of mining and mineral extraction and processing. That reputation was met, and maybe even exceeded, with the programming for the Society?s 2014 Annual Meeting in Salt Lake City, UT Feb. 23-26. The meeting drew more than 6,700 attendees to the three-day conference that featured more than 90 technical sessions with 670 presentations. These sessions covered the breadth of the mining and minerals industry, but it was the so-called ?softer issues? that were discussed in the keynote session that kicked off the meeting. The keynote session, ?Community Engagement: Building Partnerships for Mining,? brought together some of the leading voices from the mining industry, as well as some of the top voices from nongovernmental organizations (NGOs) that work in the mining sector. The common ground between the panelists was their dedication to working to ensure a social, economic and environmental balance in the development of mines. ?We wanted to bring these NGOs in to begin a dialogue to see how we can work together,? said SME President Jessica Kogel. ?This is a space that SME has not typically operated in, but one in which SME can bring a technical, scientific voice to the discussion. SME wants to play a leadership role in creating partnerships between the technical, social and economic areas that are crucial to the success of any mining project.? In today?s environment, finding mineral deposits and extracting the minerals in an economically viable manner is just one piece of an increasingly complex puzzle. Earning and maintaining a social license to operate requires careful consideration of local and global impacts. The industry often comes under intense scrutiny when a new project is proposed and, therefore, it must strive to meet the highest ethical and environmental standards. Success requires cooperation and collaboration between the industry, community and NGOs.

By Charles P. Williams

The lead-bearing area of Missouri has been subdivided, geographically, into the Southeastern, the Central, and the Southwestern

By King K. Mak

The objectives of this study are to: (1) Assess current signing regulations and practices; (2) Develop effective signing guidelines; and (3) Evaluate the applicability and appropriateness of the proposed signing guidelines through field demonstration at representative mines. A literature search was conducted to determine the state of the art for signing applicable to surface mine haulage roads as well as survey of existing MHSA regulations and review of MSHA accident records. Nine representative mines were visited to gather information on current signing practices. Preliminary signing guidelines were then developed based on the abovementioned data. Field demonstration of the preliminary signing guidelines was conducted in which signing programs were implemented in two selected mines. Signing requirements were first assessed at each of the two participating mines. Subsequently, the necessary signs were designed, purchased, and installed at the two mines. Evaluation of the signing program as to its adequacy, appropriateness, and effectiveness was solicited from both mine management and operations personnel. Experiences gained from field evaluation were then incorporated into the final signing guidelines as presented in this final report.

Jan 1, 1981

By C. Pelley, A. Piche

"The Canadian mining industry faces the prospects of a severe shortage of graduate mining engineers over the next decade. This arises from three factors: first, a growth in industrial activity; second, the average age of company engineering and management staff; and third, the reduced number of students in engineering faculties around the world. This paper aims to identify the critical factors underlying the trend of inadequate recruitment into higher education for mining and to examine means of alleviating the problem.This paper is based upon surveys of potential and current students and graduate mining engineers from four mining schools. An attempt is made to understand institutional and industrial images, career prospects and what is required to attract enough high-calibre young people into mining education over the next decade.IntroductionThe mining industry has started to experience a severe shortage of graduate mining engineers which is likely to persist and even worsen in the short- to medium-term.This arise s from three principal factors:1. a recent and strong growth in mining activity, which surpasses that experienced through the 70s, before the recent international industrial recession; .2. an increasingly older average age of mine engineering employees, at least in the industry's larger companies; and3. problems associated with maintaining adequate mining undergraduate recruitment levels ."

Jan 1, 1989