Search Documents

By R. F. Favreau, Patrice Favreau

In many quarries and construction sites visited by the authors over the last 50 years, the latter have observed muck piles from blasting with explosives, which included numerous large blocks, in some cases of dimensions larger than the input to the crusher. The names of these sites cannot be given in the article because the owners insist that data obtained on such visits be kept confidential. Often the blasters felt that the natural fissures in the rock would compensate for the use of a low powder factor, and they asked the authors to explain why such blocks were present. A detailed analysis of the situation often indicated that the cause of the blocks is that explained by figures such as 6 and 7 below in the article.

Jan 1, 2018

By AIME AIME

THE best meeting ever held, was the opinion expressed by a number of those who attended the annual meeting of the Institute in New York, Feb. 18 to 21, and there was an atmosphere of friendliness and good fellowship about it that fully justified the feeling. In numbers it was not quite so large as last year and unless the Engineering Societies should build for themselves a new building it is probable that no meeting can be larger, in respect to numbers, than that held in 1928, which was only made possible by the circumstance that the eighth floor of the building happened to be, temporarily vacant at the time. The number of rooms available for -sessions that were provided when the building was built long ago proved inadequate, and it is only by the expedient of obtaining the temporary use of the board and committee rooms of other societies that it is possible to arrange for the over 40 sessions that must be spread over the four days of the meeting. The-fifth floor, where. a buffet lunch is served each-day, has reached its full capacity and it seems quite evident that any future development of Institute meetings must be along the lines of quality, not size.

Jan 1, 1929

By F Farías, D Villa

Codelco’s Salvador Project has been operating a block/panel caving mine for more than 50 years. This underground mining method dynamically mixes the ore and dilution. As a result, forecasting grades is difficult and achieving 100 per cent extraction of the reserves is practically impossible. A substantial volume of the ore mixed with dilution becomes remnant ore and remains to be subsequently extracted.A potential open pit mine is under evaluation at Codelco’s Salvador Project, which includes the extraction of remnant ore post-block caving extraction. An effective methodology has been implemented to estimate what is left behind once the underground mine has closed. A new mixing method using the Cellular Automata (Alfaro and Saavedra, 2004) approach has been used to allow estimation of the remnant ore with a sufficient level of confidence to be included as part of the open pit reserve.A remnant block model is created using elements such as in situ block model, drawpoint layouts, historical production records and the drawpoint extraction. Using this information, simulations of the extraction of the mine by month from 1959 to 2019 were completed, using different mixing scenarios and trying to replicate the tonnage and grade extracted.Finally, the remnant block model is categorised using a score card with four inputs to assess the risk of the estimation of this material into a category class (measured, indicated and inferred).CITATION:Villa, D and Farías, F, 2016. Remnant ore model generation and categorisation post-block caving extraction at Salvador Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 461–470 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

A molten metal granulator was designed and fabricated at the U.S. Dept. of Energy, Albany Research Center, for granulation of precious metal-bearing alloys and slags. The system was designed to safely granulate a metal alloy at a temperature of up to 1,600°C at a rate of roughly 50 kg of alloy per minute. The primary water jet was supplied by a 18.6-kW, 600 liter per minute pump which provided approximately 600 kg of water per minute through the primary jet. Two 3.7-kW, 150 liter per minute auxiliary pumps provided additional wash water to wet the granulation trough through 4 secondary jets, which were placed at either side of the primary jet. The water supply was closed-loop, including a 37,850-liter supply tank and 22,710-liter recovery tank. Magnetic separators and particulate filters were included for collection of the finest fraction of the granulation product, which cleaned the water sufficiently for continuous recycle.

Jan 1, 2006

By M. D. Heresy, H. F. Coward

"Whenever a manometer has been used for recording explosion pressures it has been calibrated under a series of static pressures. Whether the readings taken during the rapidly changing pressures of an explosion (dynamic pressures) truly represent the actual pressures therefore is an open question. The authors had hoped to solve this problem by conducting the calibration with the aid of known pressures, applied at about the ammo rate as in an explosion, for example, by means of a cylinder and piston, the piston being driven in by an eccentric cam at a rate which would be determined accurately by the shape and rate of revolution of the cam. If the rate of compression were great enough, then the pressure in the cylinder (to which the manometer is attached) could be calculated from the laws of adiabatic changes of pressure and volume. It seems highly probably, however, from H. T. Tizard's observations on pressure changes in a cylinder during rapid compression (55) 4/ that there is much heat loss, therefore pressure loss, in the very small interval of time during compression; although Tizard was able to estimate the amount thereof, he did so only by relying on his nanometer, which is exactly the procedure that the authors challenge on the grounds that the manometer was not standardized under the conditions of its use. Hence the authors were driven from this scheme of calibration to another, namely, comparing records of ono and the same explosion taken simultaneously on several instruments of as varied a type as possible. If 2 of a number of instruments agree, perhaps both are accurate; if 3 agree, probably each of the 3 is accurate; if 4 agree, it is almost certain each of the 4 is accurate.There was a second objective in the present work. If the Bureau of Mines and the B.C.D. (British Coal Dust) manometers differ in their records, then from a sufficiently comprehensive series of experiments it may be possible to coordinate the extensive results already obtained at the American and British stations.Thirdly, it was hoped to learn which is the best available instrument for observing the pressures of coal-dust and as explosions and, if possible, to indicate means for improvement in manometry."

May 1, 1935

Jan 1, 2005

By Charles H. Simmons

Two versions of a VF transceiver to aid in location of trapped miners has been developed and tested. The belt worn model was produced in both transmitter and transceiver configurations. In addition, a quantity of the belt worn models were fabricated using aluminum wire instead of copper in order to reduce unit weight. Ten prototypes of a battery cap model VF transceiver were also fabricated demonstrating further unit size and weight reduction while maintaining electrical performance. Samples of- both versions were tested environmentally and the test data is included in this report. While both versions of the VF transceiver are similar electrically, and are constructed using convential manufacturing techniques, the battery cap model realizes a lower total weight, smaller volume and production cost than the belt worn version. Operationally, the battery cap model assures that the VF transceiver will always be with the miner.

Jan 1, 1981

By Clarke E. Schuetze

This project had as its objective the experimental investigation of water capsule production utilizing the Southwest Research Institute's submerged nozzle encapsulation apparatus (U.S. Patent 3,389,194). Initial efforts on this project involved nozzle configuration and shell formulation optimization. The shell formulation developed on a prior program was modified during the course of the project to obtain the best balance of capsule breakage resistance and water retention. Subsequent effort centered on determining operating conditions which would produce the best quality capsules for each candidate shell formulation as determined by laboratory tests. Some preliminary work was done to increase the production capacity of the encapsulation equipment. The program was extended with major emphasis concerned with scale-up studies of capsule production capacity and the treatment of problems associated with grouting cartridge fabrication. During the course of the program, water-containing capsules were produced which have good long-term water retention, block resistance and adequate strength. Using a single-nozzle design, a production capacity of 15.9kg (35 pounds) per hour was demonstrated to give acceptable capsules based on initial results.

Jan 1, 1978

By G C. Bolton

Experiments were conducted to access the feasibility of removing zinc from lead slag by sulfation or chlorination or both. Gaseous sulfation with sulfur dioxide and oxygen released only 50 per cent of zinc even under the most severe conditions. Sulfation with concentrated sulfuric acid by a fast-leach process released 95 per cent of zinc while pug-roasting released a maximum of 78 per cent of zinc. Chloridization with NaCl in the presence of sulfating gas released 50 per cent of zinc, while direct chlorination with chlorine gas and oxygen released 85 per cent of zinc and 100 per cent of lead in a chloride condensate containing little impurities.

Jan 1, 1980

By Kenneth Eilerts

The development and operation of "combination wells"5/ have created new and unusual problems, many of which can he solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to know, whether liquid will be formed in the reservoir as a result of isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how pressure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios off gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and. pressure of the system are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the Fluids under reservoir conditions are particularly important at this time, To meet the immediate requirements of the industry for such experimental information, an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date have been accumulated, it may be possible to make dependable estimates of the phase relations for high gas-liquid ratio fluids at the pressures anti temperatures characteristic of "combination-well? reservoirs.

Jan 1, 1940

By Wils L. Cooley

The report covers tests and criteria for the establishment of safe grounding systems for coal mines. The work deals primarily with under-ground coal mines, but much is applicable to surface mines as well. Included is an extensive guide to grounding and bonding procedures for mine surface substations. Xit-Rods are evaluated and shown to deviate from manufacturer's claims. An analysis shows that very long cables are difficult to monitor using audio frequency ground-check techniques. A method is developed to detect failing cable splices without removing the cable from service. Simulation and measurement are compared for a technique to detect bad rail bonds, and an assessment is made of grounding techniques for dc face equipment.

Jan 1, 1979

By A. Wahab Khair, John G. Oldsen, John C. Stankus, Song Guo

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews, the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Feb 24, 1997

By G. R. Robinson

Aggregate resources consist of sand and gravel, and crushed stone. They are large-tonnage, bulk-minable mineral commodities that are used in construction and industrial activities (Tepordei, 1999, 2001).Rates of aggregate production, use and mine permit approval in the mid-Atlantic region differ by population density. These rates are influenced by economic and human factors, such as demand, costs, land availability and community opposition. In some areas, the local availability of aggregate is limited. This is due to the lack of suitable local source materials for aggregate, the loss of potential high-quality aggregate resource production sites by preemptive land development and restrictive zoning (resource sterilization), and the difficulty of developing and permitting production sites for aggregate.

Jan 1, 2004

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By D. W. Fuerstenau

In 1940 Schuhmann1 showed that the size distribution of a comminuted material can be expressed by the following empirical relationship: y = 100 (|f [i] where y is the cumulative percentage of material finer than size x, k is a size modulus, and a is a distribution modulus which is constant for a given material and machine. During the past few years, considerable emphasis has been given to the investigation of the extent of size reduction resulting from the expenditure of mechanical energy in crushing and grinding. Recently Schuhmann' presented a derivation of the energy-size reduction relationship by postulating that comminution in a device such as a ball mill can be considered to be the summation of many single comminution events, each of which yields a size distribution of particles following the Schuhmann size distribution equation. By grinding

Jan 1, 1961

By H. A. Domian, H. Biloni, G. F. Bolling

Jan 1, 1965

By P. J. Rua

The Piedras Verdes copper mine is a new run-of-mine (ROM), heap leach, solvent-extraction/electrowinning (SX-EW) operation located 21 km (13 miles) north-northwest of the town of Alamos in the state of Sonora, Mexico. The Piedras Verdes copper mine is wholly owned by Frontera Copper Corp. (FCC), a Canadian corporation, through its 100 percent beneficial interest in Cobre del Mayo S.A. de C.V. (CDM), a Mexican registered company. The January 2008, minable reserves were estimated to be 193.6 Mt (213 million st) at a grade of 0.36 percent copper. The overall recovery of total copper was estimated to be 61.9 percent. The property has an additional 17-year life and is designed to produce 31.7 kt/a (70 million lbs/year) of cathode copper. Construction commenced in early October 2005. The first copper cathode was produced 12 months later at a total capital cost of $100 million. Elevations at the site range from 150 to 300 m (490 to 985 ft) above sea level. The area has excellent infra-structure in the form of towns, power, water, roads, rail, airfield and access to the deepwater port of Guaymas (Fig. 1). The surrounding area is also famous for its numerous polymetallic (lead, zinc, copper, silver and gold) epithermal veins. Some of these were mined for more than 200 years and provided the wealth on which the town of Alamos was built. The original village of Piedras Verdes was located in the area of the proposed openpit mine and, consequently, it was necessary to construct a new townsite 6 km (3.7 miles) to the south before project development could commence. The new town site (Fig. 2), complete with power and water supplies, roads, sewer system, schools, clinic and recreational facilities, was completed and occupied by 49 families in September 2005. CDM received its remaining permits from the Mexican environmental authorities on Sept. 20, 2005. This enabled the company to proceed with full-scale development. CDM owns or controls 27 mining concessions covering the resource. Surface rights to the Piedras Verdes project were controlled by four Ejidos (communal agrarian and/or ranching societies) and five individual landowners. CDM has acquired all surface rights necessary for its mining operations and associated facilities either through outright purchase or long term lease agreements.

Jan 1, 2008

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. But wait a minute: Isn't head loss a negative number, a debit? And isn't fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves - pressure losses as negative values and energy additions as positive values-and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Feb 24, 1997

By M. E. Wadsworth, T. D. Chatwin

The kinetics of sulfidization of hematite (Fe203) by H2S gas at various partial pressures have been determined over the temperature range of 170° to 500°C. The process was controlled by thin films of pyrite (FeS2) and troilite (FeS) which were protective and formed diffusional layers. At higher temperatures the thermodynamic drive to form FeS2 decreased, and consequently the rate of formation of FeS, decreased. Conditions for the development of thin layers of FeSz consisting of 10 to 100 atomic diameters are presented. Laboratory flotation results on synethetic ores indicate floatability identical to that of pyrite of normal xanthate flotation. The prospect of high-temperature sulfidization of metal oxides using H2S, S, or other sulfur bearing compounds is intriguing as a potential activation process for flotation since the thermodynamics are very favorable for a large number of systems. If the kinetic parameters are sufficiently well understood it may be possible to provide surface sulfide layers a few angstroms thick, thus imparting normal sulfide floatability characteristics to the oxide. For thin layers the total sulfur pick-up would be small except for very high surface area materials but in most cases this sulfur could be readily removed by roasting if necessary. The general reactions for the sul-fidization of metal oxide MxO, to a metal sulfide MpSq using H2S may be written for the three conditions py > xq; py < xq; and py = xq: A large thermodynamic advantage is obtained in many systems because of the relatively large negative free energy of formation of H,O compared to H,S. For the temperature range 2S° to 1500°C &apos; where AFOis the standard free energy and T is absolute temperature. As is evident from Eqs. 4 and 5, the free energy of formation of H ,0 is approximately 35 to 37 kilocalories per mole greater than that for H,S over broad variations of temperature. For oxide-sulfide systems as outlined above, sulfidization may be expected to occur for the conditions: Groups I and 111: that is, if the terms on the right are more negative than those on the left the reaction is expected to occur thermodynamically. The value hFg,(,) is included in Eq. 6 since hFLzs is based upon gaseous S2 rather than the normal reference state, orthorhombic sulfur. The

Jan 1, 1969