Search Documents

By J. O. Marsden

Part I in this series of papers considered the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical testing and initial process development for this technology. This initial work resulted in the development of a process flowsheet utilizing superfine grinding (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160° to 170ºC, followed by conventional solution extraction (SX) and electrowinning (EW) for the recovery of copper. However, this process required a significant amount of concentrated acid to be fed to the pressure leach vessel to meet the reaction requirements, representing a cost of between $0.03 and 0.05/lb copper (2006 basis) produced by the process. It was immediately recognized that the development of a process that did not require such a large acid addition would be advantageous. This paper, which is Part II in the series, describes the development of a process that incorporates medium-temperature pressure leaching and direct electrowinning (DEW) in a novel and innovative process flowsheet. Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold Inc.) refers to this as the ?MT-DEW-SX? process. Part III in this series covers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By J. P. Ulery

As a result of several recent methane/dust ignitions in surface auger and highwall mines, the U.S. Bureau of Mines investigated the occurrence of methane gas at these operations. Three mine sites were visited in western Kentucky and one in western Pennsylvania to collect run-of-mine coal samples for gas content determination using the modified-direct-method (MOM). Results indicate the samples emitted small quantities of methane, carbon dioxide, and nitrogen. Either methane or nitrogen was the predominant gas released. The same gases were released after crushing the samples for residual gas content; however, nitrogen was the primary component of this fraction. Total ~as contents ranged from less than 0.01 cm /g to 0.54 cm3/g. The hydrocarbon gases probably originated during coalification. Other gases may have originated partially as a byproduct of coalification and partially as a result of other, near-surface processes. The data suggest that although methane quantities are small, desorption could occur at near surface conditions prior to mining. The desorbed methane could accumulate as a free gas in fractures in the coal bed or roof rock. When these fractures are penetrated by the auger, methane could rapidly enter the whole atmosphere possibly creating explosive conditions.

Jan 1, 1994

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By C. O. Brawner, J. Kalejta II

The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than about 45°. As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result with less rock fall capacity. The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented.

Jan 1, 2002

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982

The use of belt air in underground coal mines has been a continuous discussion since it was first introduced in the Federal Coal Mine Health and Safety Act (Coal Act) of 1969. Although the Coal Act prohibits the use of belt air to ventilate active workings, there were two exceptions prior to the 2004 Final Rule. There have been several major studies/rule-proposals by MSHA since 1985 and the most recent of which is the Technical Study Panel (TSP) established by the Mine Improvement and New Emergency Response (MINER) Act of 2006 to study the use of belt air and related issues. This paper reviews the history of belt air use, its associated controver-sies, and more specifically, the 20 recommendations unanimously approved by the TSP.

Jan 1, 2009

By J. G. Kirby

According to the Bureau of Mines annual survey, as of January 1, 1954 there were 337 refineries with a total daily crude-oil throughput capacity of 8,006,897 barrels. The total daily capacity increased 368,236 barrels during the year while the total number of refineries declined 6. The capacity of the average refinery to process crude oil therefore increased during 1953 from 22,270 barrels to 23,759. With the exception of the Texas Inland, all refining districts reported gains in the installed capacity for the year, the largest being the Louisiana Gulf Coast with an increase of 20 percent. A total of 397,500 barrels of additional crude oil capacity was reported as under construction January 1, 1954. Accounting for 129,500 barrels of this total are facilities for 3 new refineries in North Dakota, 2 in Washington and I each in Ohio and Utah. Equipment being installed to replace existing units, totaled 180,750 barrels daily.

Jan 1, 1954

By E. P. Ferrero

Analyses of 38 crude oil samples from 25 fields in Algeria, Libya, and Nigeria are presented in this report. The 38 crude oils are listed alphabetically by country and field. Also shown are the geographic and geologic sources of the samples analyzed, the companies that supplied the samples, the general characteristics and analytical and computed data, and the production for the fields from which the samples were obtained.

Jan 1, 1966

By J. B. Gwiazda

S.S. Peng The highlights of this paper are : • The shield supports with lemniscate links will exert a tangential force on the roof strata, causing unnecessary and harmful roof movements, thus damaging the roof structure. The principal source of the tangential force is the horizontal movement of the point O, the pivotal joint between the canopy and the caving shield. When the support height is changed during setting, the point O will move along a curve upward and rearward toward the gob. As a result, it produces a vertical movement, causing the roof to move up a distance of ?d, and a horizontal movement toward the gob, creating vertical fractures in the roof. • The major purpose for employing the lemniscate-link system is to protect the hydraulic legs against the action of the bending moments induced by the tangential force that causes deformation or destruction of the legs. • Based on these two points, the author suggested that, in order to eliminate the harmful effects of the lemniscate-link system and strengthen its advantageous features, a shield support with a new design of that mechanism has been developed. With the new design, the conventional rigid lemniscate links are replaced by hydraulic rams. When the pressure inside the rams reaches a certain level, the ram will yield.

Jan 12, 1986

By E. P. Ferrero

Analyses of 38 crude oil samples from 25 fields in Algeria, Libya, and Nigeria are presented in this report. The 38 crude oils are listed alphabetically by country and field. Also shown are the geographic and geologic sources of the samples analyzed, the companies that supplied the samples, the general characteristics and analytical and computed data, and the production for the fields from which the samples were obtained.

Jan 1, 1966

By Nestor Chavez, Daniel Alayza

Taucane es un nuevo descubrimiento efectuado por Minsur S.A. en el año 2014, siendo el primer depósito de estaño ligado a mantos y vetas con contenido de sulfuros en Ag-Pb-(Zn-Sn) hospedados en las secuencias sedimentarias calcáreas de la franja morfo-estructural Pre-Cordillera de Carabaya (Puno), y único en su tipo en el sur del Perú.

May 1, 2008

By Patrick Bermingham

This report presents the results of six STATNAMIC loading tests that were carried out on four different pile types at the CALTRANS 280 Test Site (Bridge No. 34-46) in conjunction with the Tension Pile Test Program. The STATNAMIC testing was performed by Berminghammer Corporation at the request of the California Department of Transportation, Office of Geotechnical Engineering. Others performed the static tension (uplift) and compression loading tests which werecarried out on the piles tested using the STATNAMIC method. A summary of the STATNAMIC test results is presented and discussed, and the appropriate results are compared with the static test results

Jan 1, 1993

The following paper on the development of processes for the treatment of crude ore, accumulated dumps of tailing and slime at Broken Hill, has been prepared by a committee of the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy, with the object of recording, in chronological order, the developments of the various processes which have led up to the metallurgical practice of the present day.

Jan 1, 1930

By Issa S. Oweis

Limestone is a sedimentary rock composed primarily of calcite (calcium carbonate). In the presence of an aqueous solution of carbon dioxide (carbonic acid) bicarbonate radicals (2HCO3)- are produced that are highly soluble. The same type of reactions occur in terrains where dolomite (calcium magnesium bicarbonate) reacts with carbonic acid to produce highly soluble bicarbonates (4HCO3)-. The source of carbon dioxide is the small content in rainfall but to a large extent from the organics in the soil. The solution activity depends on many factors including the content of carbon in the rock, acidity of soil water, groundwater velocity and other factors. The resulting features are referred to in literature as sinkholes, solution channels, caves, karstic topography, and cavernous limestone. The presence of solution features affect the shafts in several ways: (a) the shaft resistance is affected by voids along the shaft, (b) concreting of the shaft should consider the presence of voids along the shaft, and (c) the shaft base may be in close proximity to a solution feature that may cause future collapse under structural loads. Methods to mitigate such effects include verification of rock to below the base (vertically and laterally). Cavities are stable by virtue of arching in the rock. Under the action of end bearing from a shaft, the arch may collapse depending on its proximity to the base of the shaft and the strength of the rock. This paper focuses on this issue. Finite Element analyses are conducted to relate shaft end load and bearing area that will produce failure based on given rock properties, size and location of cavity. Failure is defined as settlement of the base equivalent to 5% of shaft socket diameter. The software Plaxis is used for analysis. The rock is considered as c-f material derived based on Hoek-Brown failure criteria (2002 edition) that is based on Geological Strength Index (GSI).

Jan 1, 2009

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By J. R. Hoskins

This is the final report for Research Contract No. 00101300 (Min. 34) granted by the U.S. Bureau of Mines to the University of Idaho Mining Research Bureau. The research project is entitled "Development of Improved Ventilation Technology for Non-coal Mines and Other Underground Excavations.' The duration of the project was six calendar months, from 16 April to 16 October 1970. The budgeted cost was $34,867.00 of which $31,953.00 was to be furnished by the U.S. Bureau of Mines. The sequence of reporting that follows is to state the objectives as contracted, outline the program of investigation, highlight briefly the important technological factors peculiar to vein-type metal mine ventilation, and describe the normal methods of control. This is followed by the results achieved by the survey, and an itemization of the observed deficiencies in current technology. There follows a section dealing with the adopted Federal Regulations.

Jan 1, 1970

By Michel Robert

"In 1974, Copperfields Mining Corporation and Soquem formed a new company, Niobec Inc, to bring the niobium deposit of the St-Honore carbonatite into production.St-Honore is located in the Saguenay area, near the cities of Chicoutimi and Arvida, and about one hundred and forty (140) miles north of Quebec. The discovery of the carbonatite complex was made in the fall of 1967 as a result of an airborne radiometric survey in search of uranium. The detailed exploration of the carbonatite indicated two niobium-bearing formations besides the original discovery of a rare earths zone. During the following years, the niobium formations were defined by diamond drilling and a decline was driven down to obtain adequate samples for metallurgical evaluation. In 1974, after seven hundred (700) bench scale tests, eleven (11) months of pilot plant 2nd a worldwide market research, a joint decision was made to initiate the development of a fifteen hundred (1500) T.P.D. mine and mill, under the management of Teck Corporation. The construction of the facilities were completed in early 1976 both on time and within budget. Niobec is now the only north american and the world second largest producer of Niobium concentrate.The process used at Niobec was developed from the pilot plant programs and later modified by the mill personnel. A simplified flowsheet for this process is shown on the slide. Briefly, run of mine ore is crushed to minus 5/8"" and fed to a rod mill, ball mill, and screens circuit where the ore is ground to 92% passing 65 mesh. The ore is deslimed in two stages of cycloning, and the final cyclone overflow at 85% minus 11 microns goes to waste. The cyclone underflow is conditioned prior to flotation of a carbonate-apatite concentrate. This concentrate is cleaned twice and then pumped to tails. The carbonate rougher and cleaner tails are cycloned in two stages to change the process; water and then sent to the pyrochlore rougher flotation. The rougher concentrate is cleaned five times. This is followed by pyrite flotation to remove sulfur, leaching with hydrochloric acid to remove phosphorus and dyed to less than 0.1% moisture before being sent to packaging."

Jan 1, 1978

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009

By Gerald A. Crawford

"1880s - Unmasking the Sudbury Basin Falconbridge Ltd. turned 60 in 1988 but its roots go back more than a century to the discovery and development of the mineral resources of the Sudbury Basin. Nickel was first identified in the area in 1856 but sustained exploration awaited the early 1880s and the advance of the CPR westward from Sudbury. Rock was laid bare in the right-of-way and by forest fires and logging. Reddish oxidized outcropping or ""gossan"" were exposed, heralding the presence of nickel as the shape of this astounding geological formation gradually began to emerge. Many great mines of the area were opened up in this period on the south rim of the Basin west of Sudbury. To the east the ore dips below overburden, however, and Falconbridge remained a mere dot on the map until the turn of the century when Thomas Edison detected a magnetic occurrence by dip needle."

Jan 1, 1999

By B. M. O'Harra

Zinc smelting is frequently termed a ba.ckward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, lowunit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pou~ds of ore. The diameter of the retort is limited by the tirrie required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, qr ·producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser. attached to one end of the retort, where it conde_nses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls 11.nd of the ore charge itself, the heat efficiency even of the most modern regenerative furnacei;; is only about 12 per cent. The retorts have a short life, 30 to 6Q days, at the high temperature required-; zinc losses are heavy, usually 10 per cent or more; and the proportion of impurities in the retort charge must be carefully controlled to prevent the rapid corrosion of retorts. For these reasons, much work has been done in an e:ff ort to, find cheaper and more efficient methods o.f recovering zinc from its ores. Various methods have been proposed for smelting in the blast furnace. Some of these contemplated the production of zinc vapor and its condensation to liquid; others attempted to produce liquid zinc directly by smelting under pressure. It is now realized that fundamental difficulties render these proposals impracticable. The electric furnace for smelting offers obvious advantages in the way of the efficient utilization of energy, large units, easy attainment of high temperatures, and the possibility of treating complex ores. E. H. and A. H. Cowles first suggested a design for an electric furnace for the reduction of zinc ores and patented their process in 1885. Their attention was soon directed to other uses for their furnace and nothing further of importance was done in the electric smelting of zinc until about 1900. Several investigators then started work upon various processes and had more or less success. The chief difficulty they encountered was the impossibility of obtaining more, than a small amount of the zinc as liquid metal because most of the zinc vapor condensed as blue powder. Interest in the electrothermic metallurgy of zinc increased, many patents on processes and furnace design were taken out, and the literature on the subject grew, until in 1914 and 1915 the problem seemed to be approaching solution. About this time the hydrometallurgy of zinc, the development of which had been lagging somewhat behind that of the electrothermic metallurgy, sprang into the limelight and a commercial process was soon perfected. This rapid development, perhaps aided by the war premium on the high-grade spelter produced by electrolytic deposition, distracted attention from electric smelting to some extent, though progress continued. With the perfection and standardization of the electrolytic process has come a better realization of its limitations, especially the necessity for large-scale operation ·and the difficulty of obtaining high extraction. Because of these limitations the electrothermic metallurgy of zinc still has a field of its own and in fac-t promises to become a strong competitor of both hydrometallurgy and retort smelting except under conditions highly favorable to the latter methods. Because of the imperfections of the retort and electrolytic processes and the promise that the electric furnace offers in overcoming these imperfections, the. United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, has undertaken a study of the electrothermic metallurgy of zinc.

Jan 1, 1923